Mixed Linearity Improvement Techniques for Ultra-wideband Low Noise Amplifier

We present the linearization of an ultra-wideband low noise amplifier (UWB-LNA) operating from 2GHz to 11GHz through combining two linearization methods. The used linearization techniques are the combination of post-distortion cancellation and derivative-superposition linearization methods. The linearized UWB-LNA shows an improved linearity (IIP3) of +12dBm, a minimum noise figure (NFmin.) of 3.6dB, input and output insertion losses (S11 and S22)  below -9dB over the entire working bandwidth, midband gain of 6dB at 5.8GHz, and overall circuit power consumption of 24mW supplied from a 1.5V voltage source. Both UWB-LNA and linearized UWB-LNA designs are verified and simulated with ADS2016.01 software using BSIM3v3 TSMC 180nm CMOS model files. In addition, the linearized UWB-LNA performance is compared with other recent state-of-the-art LNAs

A Novel High Linearity and Low Power Folded CMOS LNA for UWB Receivers

© 2017 World Scientific Publishing Company. Electronic version of an article published as Journal of Circuits, Systems and Computers, Vol. 27, No. 03, 1850047, https://doi.org/10.1142/S0218126618500470.This paper presents a high linearity and low power Low-Noise Amplifier (LNA) for Ultra-Wideband (UWB) receivers based on CHRT 0.18μm CMOS technology. In this work, the folded topology is adopted in order to reduce the supply voltage and power consumption. Moreover, a band-pass LC filter is embedded in the folded-cascode circuit to extend bandwidth. The transconductance nonlinearity has a great impact on the whole LNA linearity performance under a low supply voltage. A post-distortion (PD) technique employing an auxiliary transistor is applied in the transconductance stage to improve the linearity. The post-layout simulation results indicate that the proposed LNA achieves a maximum power gain of 12.8dB. The input and output reflection coefficients both are lower than -10.0dB over 2.5~11.5GHz. The input third-order intercept point (IIP3) is 5.6dBm at 8GHz and the noise figure (NF) is lower than 4.0dB. The LNA consumes 5.4mW power under a 1V supply voltage.Peer reviewe

An Ultra-wideband Low-power Low-noise Amplifier Linearized by Adjusted Derivative Superposition and Feedback Techniques

Ultra-wideband (UWB) applications require low-power and low-noise amplifiers (LNAs) that can operate over a wide frequency range. However, conventional LNAs often suffer from poor linearity and high-power consumption. This research work proposes a novel LNA design that uses the adjusted derivative superposition (DS) technique and feedback to improve the linearity and reduce the power consumption of UWB LNAs. The DS technique enhances the third-order intermodulation (IM3) cancellation by adjusting the bias currents of the transistors, whereas the feedback improves the stability and input matching of the LNA. The LNA is implemented using a degenerated common source topology in a 180 nm standard CMOS technology. The simulation results show that the LNA achieves a power gain of 10–12.2 dB, an input third-order intercept point (IIP3) of about 12 dBm, and a noise figure of less than 2.5 dB over the UWB frequency band of 3.1–10.6 GHz. The input reflection coefficient is less than -10 dB, and the power consumption is 11.6 mW with a 1.5 V power supply. The designed LNA offers a novel and innovative solution for UWB applications that significantly improve the performance and efficiency of UWB LNAs whereas reducing the cost and complexity of implementation

9.1 dBm IIP3 36 dB Gain Controllable LNA for WCDMA in 0.13-m CMOS

This article presents a low-power, high-linearity cascodetype low noise amplifier (LNA) with 36 dB of variable gain for the WIDE Code Division Multiple Access systems. By enhancing the substrate resistance of a common gate transistor along with adopting multiple-gate technique, the linearity is significantly improved. Shunt-current steering is adopted for smooth gain control. Step gain mode is used to further increase the gain control range. The main common source transistor is disabled in attenuation mode, saving unwanted power consumption. Measurements show maximum gain of 12.3 dB with S11 of 19.5 dB, and S22 of 14 dB. The total gain control range is 36 dB. NF is measured as 2 dB and two-tone test shows 9.1 dBm of IIP3. Implemented in 0.13-m CMOS technology, the LNA consumes only 1.6 mA at maximum gain mode and only 0.2 mA in attenuation mode from 1.2 V supply. Its die size is 0.3 mm2. © 2009 Wiley Periodicals, Inc. Microwave Opt Technol Lett 51: 1385–1388, 2009; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/mop. 2432

Discrete-Time Mixing Receiver Architecture for RF-Sampling Software-Defined Radio

A discrete-time (DT) mixing architecture for RF-sampling receivers is presented. This architecture makes RF sampling more suitable for software-defined radio (SDR) as it achieves wideband quadrature demodulation and wideband harmonic rejection. The paper consists of two parts. In the first part, different downconversion techniques are classified and compared, leading to the definition of a DT mixing concept. The suitability of CT-mixing and RF-sampling receivers to SDR is also discussed. In the second part, we elaborate the DT-mixing architecture, which can be realized by de-multiplexing. Simulation shows a wideband 90° phase shift between I and Q outputs without systematic channel bandwidth limitation. Oversampling and harmonic rejection relaxes RF pre-filtering and reduces noise and interference folding. A proof-of-concept DT-mixing downconverter has been built in 65 nm CMOS, for 0.2 to 0.9 GHz RF band employing 8-times oversampling. It can reject 2nd to 6th harmonics by 40 dB typically and without systematic channel bandwidth limitation. Without an LNA, it achieves a gain of -0.5 to 2.5 dB, a DSB noise figure of 18 to 20 dB, an IIP3 = +10 dBm, and an IIP2 = +53 dBm, while consuming less than 19 mW including multiphase clock generation

Flexible Receivers in CMOS for Wireless Communication

Consumers are pushing for higher data rates to support more services that are introduced in mobile applications. As an example, a few years ago video-on-demand was only accessed through landlines, but today wireless devices are frequently used to stream video. To support this, more flexible network solutions have merged in 4G, introducing new technical problems to the mobile terminal. New techniques are thus needed, and this dissertation explores five different ideas for receiver front-ends, that are cost-efficient and flexible both in performance and operating frequency. All ideas have been implemented in chips fabricated in 65 nm CMOS technology and verified by measurements. Paper I explores a voltage-mode receiver front-end where sub-threshold positive feedback transistors are introduced to increase the linearity in combination with a bootstrapped passive mixer. Paper II builds on the idea of 8-phase harmonic rejection, but simplifies it to a 6-phase solution that can reject noise and interferers at the 3rd order harmonic of the local oscillator frequency. This provides a good trade-off between the traditional quadrature mixer and the 8- phase harmonic rejection mixer. Furthermore, a very compact inductor-less low noise amplifier is introduced. Paper III investigates the use of global negative feedback in a receiver front-end, and also introduces an auxiliary path that can cancel noise from the main path. In paper IV, another global feedback based receiver front-end is designed, but with positive feedback instead of negative. By introducing global positive feedback, the resistance of the transistors in a passive mixer-first receiver front-end can be reduced to achieve a lower noise figure, while still maintaining input matching. Finally, paper V introduces a full receiver chain with a single-ended to differential LNA, current-mode downconversion mixers, and a baseband circuity that merges the functionalities of the transimpedance amplifier, channel-select filter, and analog-to-digital converter into one single power-efficient block

HIGH LINEARITY UNIVERSAL LNA DESIGNS FOR NEXT GENERATION WIRELESS APPLICATIONS

Design of the next generation (4G) systems is one of the most active and important area of research and development in wireless communications. The 2G and 3G technologies will still co-exist with the 4G for a certain period of time. Other applications such as wireless LAN (Local Area Network) and RFID are also widely used. As a result, there emerges a trend towards integrating multiple wireless functionalities into a single mobile device. Low noise amplifier (LNA), the most critical component of the receiver front-end, determines the sensitivity and noise figure of the receiver and is indispensable for the complete system. To satisfy the need for higher performance and diversity of wireless communication systems, three LNAs with different structures and techniques are proposed in the thesis based on the 4G applications. The first LNA is designed and optimized specifically for LTE applications, which could be easily added to the existing system to support different standards. In this cascode LNA, the nonlinearity coming from the common source (CS) and common gate (CG) stages are analyzed in detail, and a novel linear structure is proposed to enhance the linearity in a relatively wide bandwidth. The LNA has a bandwidth of 900MHz with the linearity of greater than 7.5dBm at the central frequency of 1.2GHz. Testing results show that the proposed structure effectively increases and maintains linearity of the LNA in a wide bandwidth. However, a broadband LNA that covers multiple frequency ranges appears more attractive due to system simplicity and low cost. The second design, a wideband LNA, is proposed to cover multiple wireless standards, such as LTE, RFID, GSM, and CDMA. A novel input-matching network is proposed to relax the tradeoff among noise figure and bandwidth. A high gain (>10dB) in a wide frequency range (1-3GHz) and a minimum NF of 2.5dB are achieved. The LNA consumes only 7mW on a 1.2V supply. The first and second LNAs are designed mainly for the LTE standard because it is the most widely used standard in the 4G communication systems. However, WiMAX, another 4G standard, is also being widely used in many applications. The third design targets on covering both the LTE and the WiMAX. An improved noise cancelling technique with gain enhancing structure is proposed in this design and the bandwidth is enlarged to 8GHz. In this frequency range, a maximum power gain of 14.5dB and a NF of 2.6-4.3dB are achieved. The core area of this LNA is 0.46x0.67mm2 and it consumes 17mW from a 1.2V supply. The three designs in the thesis work are proposed for the multi-standard applications based on the realization of the 4G technologies. The performance tradeoff among noise, linearity, and broadband impedance matching are explored and three new techniques are proposed for the tradeoff relaxation. The measurement results indicate the techniques effectively extend the bandwidth and suppress the increase of the NF and nonlinearity at high frequencies. The three proposed structures can be easily applied to the wideband and multi-standard LNA design