PVT-Robust Ultra-Low-Jitter Clock Multipliers Using an Injection-Locking Technique

Department of Electrical EngineeringThis thesis presents process-voltage-temperature (PVT)-robust ultra-low-jitter clock multipliers using an injection-locking technique. First, an injection-locked clock multiplier (ILCM) using a two-phase PVT-calibrator is proposed. The proposed PVT-calibration technique is based on the dual-loop architecture which consists of a main-voltage-controlled oscillator (VCO) and a replica-VCO. While the main-VCO is injection-locked and generates the precise target frequency, the real-time frequency variation of the replica-VCO can be monitored by the PVT-calibrator which adjusts the control voltage shared by the two identical VCOs. Using the two-phase calibration technique, the tradeoff between the calibration resolution and the lock time was removed. The proposed ILCM, fabricated in the 65-nm CMOS process, generated five different reference frequencies, i.e., 19.2, 28.8, 48.0, 57.6, and 96.0 MHz with a 19.2 MHz external clock. When injection-locked, the integrated jitter from 1 kHz to 10 MHz of the 96-MHz signal was 1.69 ps. The proposed PVT-calibrator restricted the phase noise degradation over the temperature range of 30 to 80 ??C to less than 0.5 dB. Second, a fractional-resolution ILCM using a delay-locked-loop (DLL)-based PVT-calibrator is proposed. In this architecture, the ring-type VCO and the voltage-controlled delay line (VCDL) of the DLL consist of identical delay cells, and they share the same control voltage. Thus, by changing the ratio between the numbers of stages of the VCDL and the VCO, the frequency of the VCO can be calibrated at a target frequency, a non-integer times the reference frequency. The proposed ILCM, designed in the 65-nm CMOS process, generated output frequencies that range from 1.2 to 2.0 GHz with a frequency resolution of 40 MHz with a 400-MHz reference clock. When injection-locked, the integrated jitter from 1 kHz to 40 MHz of the 1.6-GHz signal was 440 fs. The proposed DLL-based PVT-calibrator restricted the degradations of phase noise and jitter over the temperature and the supply variations to less than 0.7 dB and 20%, respectively. Both architectures presented in this thesis can overcome real-time frequency drifts as well as static process variationsthus, excellent jitter performance can be sustained during any environmental variations.ope

Self-Calibrated, Low-Jitter and Low-Reference-Spur Injection-Locked Clock Multipliers

Department of Electrical EngineeringThis dissertation focuses primarily on the design of calibrators for the injection-locked clock multiplier (ILCM). ILCMs have advantage to achieve an excellent jitter performance at low cost, in terms of area and power consumption. The wide loop bandwidth (BW) of the injection technique could reject the noise of voltage-controlled oscillator (VCO), making it thus suitable for the rejection of poor noise of a ring-VCO and a high frequency LC-VCO. However, it is difficult to use without calibrators because of its sensitiveness in process-voltage-temperature (PVT) variations. In Chapter 2, conventional frequency calibrators are introduced and discussed. This dissertation introduces two types of calibrators for low-power high-frequency LC-VCO-based ILFMs in Chapter 3 and Chapter 4 and high-performance ring-VCO-based ILCM in Chapter 5. First, Chapter 3 presents a low power and compact area LC-tank-based frequency multiplier. In the proposed architecture, the input signals have a pulsed waveform that involves many high-order harmonics. Using an LC-tank that amplifies only the target harmonic component, while suppressing others, the output signal at the target frequency can be obtained. Since the core current flows for a very short duration, due to the pulsed input signals, the average power consumption can be dramatically reduced. Effective removal of spurious tones due to the damping of the signal is achieved using a limiting amplifier. In this work, a prototype frequency tripler using the proposed architecture was designed in a 65 nm CMOS process. The power consumption was 950 ??W, and the active area was 0.08 mm2. At a 3.12 GHz frequency, the phase noise degradation with respect to the theoretical bound was less than 0.5 dB. Second, Chapter 4 presents an ultra-low-phase-noise ILFM for millimeter wave (mm-wave) fifth-generation (5G) transceivers. Using an ultra-low-power frequency-tracking loop (FTL), the proposed ILFM is able to correct the frequency drifts of the quadrature voltage-controlled oscillator of the ILFM in a real-time fashion. Since the FTL is monitoring the averages of phase deviations rather than detecting or sampling the instantaneous values, it requires only 600??W to continue to calibrate the ILFM that generates an mm-wave signal with an output frequency from 27 to 30 GHz. The proposed ILFM was fabricated in a 65-nm CMOS process. The 10-MHz phase noise of the 29.25-GHz output signal was ???129.7 dBc/Hz, and its variations across temperatures and supply voltages were less than 2 dB. The integrated phase noise from 1 kHz to 100 MHz and the rms jitter were???39.1 dBc and 86 fs, respectively. Third, Chapter 5 presents a low-jitter, low-reference-spur ring voltage-controlled oscillator (ring VCO)-based ILCM. Since the proposed triple-point frequency/phase/slope calibrator (TP-FPSC) can accurately remove the three root causes of the frequency errors of ILCMs (i.e., frequency drift, phase offset, and slope modulation), the ILCM of this work is able to achieve a low-level reference spur. In addition, the calibrating loop for the frequency drift of the TP-FPSC offers an additional suppression to the in-band phase noise of the output signal. This capability of the TP-FPSC and the naturally wide bandwidth of the injection-locking mechanism allows the ILCM to achieve a very low RMS jitter. The ILCM was fabricated in a 65-nm CMOS technology. The measured reference spur and RMS jitter were ???72 dBc and 140 fs, respectively, both of which are the best among the state-of-the-art ILCMs. The active silicon area was 0.055 mm2, and the power consumption was 11.0 mW.clos

LOW-JITTER AND LOW-SPUR RING-OSCILLATOR-BASED PHASE-LOCKED LOOPS

Department of Electrical EngineeringIn recent years, ring-oscillator based clock generators have drawn a lot of attention due to the merits of high area efficiency, potentially wide tuning range, and multi-phase generation. However, the key challenge is how to suppress the poor jitter of ring oscillators. There have been many efforts to develop a ring-oscillator-based clock generator targeting very low-jitter performance. However, it remains difficult for conventional architectures to achieve both low RMS jitter and low levels of reference spurs concurrently while having a high multiplication factor. In this dissertation, a time-domain analysis is presented that provides an intuitive understanding of RMS jitter calculation of the clock generators from their phase-error correction mechanisms. Based on this analysis, we propose new designs of a ring-oscillator-based PLL that addresses the challenges of prior-art ring-based architectures. This dissertation introduces a ring-oscillator-based PLL with the proposed fast phase-error correction (FPEC) technique, which emulates the phase-realignment mechanism of an injection-locked clock multiplier (ILCM). With the FPEC technique, the phase error of the voltage-controlled oscillator (VCO) is quickly removed, achieving ultra-low jitter. In addition, in the transfer function of the proposed architecture, an intrinsic integrator is involved since it is naturally based on a PLL topology. The proposed PLL can thus have low levels of reference spurs while maintaining high stability even for a large multiplication factor. Furthermore, it presents another design of a digital PLL embodying the FPEC technique (or FPEC DPLL). To overcome the problem of a conventional TDC, a low-power optimally-spaced (OS) TDC capable of effectively minimizing the quantization error is presented. In the proposed FPEC DPLL, background digital controllers continuously calibrate the decision thresholds and the gain of the error correction by the loop to be optimal, thus dramatically reducing the quantization error. Since the proposed architecture is implemented in a digital fashion, the variables defining the characteristics of the loop can be easily estimated and calibrated by digital calibrators. As a result, the performances of an ultra-low jitter and the figure-of-merit can be achieved.clos

고속 시리얼 링크를 위한 고리 발진기를 기반으로 하는 주파수 합성기

학위논문(박사) -- 서울대학교대학원 : 공과대학 전기·정보공학부, 2022. 8. 정덕균.In this dissertation, major concerns in the clocking of modern serial links are discussed. As sub-rate, multi-standard architectures are becoming predominant, the conventional clocking methodology seems to necessitate innovation in terms of low-cost implementation. Frequency synthesis with active, inductor-less oscillators replacing LC counterparts are reviewed, and solutions for two major drawbacks are proposed. Each solution is verified by prototype chip design, giving a possibility that the inductor-less oscillator may become a proper candidate for future high-speed serial links. To mitigate the high flicker noise of a high-frequency ring oscillator (RO), a reference multiplication technique that effectively extends the bandwidth of the following all-digital phase-locked loop (ADPLL) is proposed. The technique avoids any jitter accumulation, generating a clean mid-frequency clock, overall achieving high jitter performance in conjunction with the ADPLL. Timing constraint for the proper reference multiplication is first analyzed to determine the calibration points that may correct the existent phase errors. The weight for each calibration point is updated by the proposed a priori probability-based least-mean-square (LMS) algorithm. To minimize the time required for the calibration, each gain for the weight update is adaptively varied by deducing a posteriori which error source dominates the others. The prototype chip is fabricated in a 40-nm CMOS technology, and its measurement results verify the low-jitter, high-frequency clock generation with fast calibration settling. The presented work achieves an rms jitter of 177/223 fs at 8/16-GHz output, consuming 12.1/17-mW power. As the second embodiment, an RO-based ADPLL with an analog technique that addresses the high supply sensitivity of the RO is presented. Unlike prior arts, the circuit for the proposed technique does not extort the RO voltage headroom, allowing high-frequency oscillation. Further, the performance given from the technique is robust over process, voltage, and temperature (PVT) variations, avoiding the use of additional calibration hardware. Lastly, a comprehensive analysis of phase noise contribution is conducted for the overall ADPLL, followed by circuit optimizations, to retain the low-jitter output. Implemented in a 40-nm CMOS technology, the frequency synthesizer achieves an rms jitter of 289 fs at 8 GHz output without any injected supply noise. Under a 20-mVrms white supply noise, the ADPLL suppresses supply-noise-induced jitter by -23.8 dB.본 논문은 현대 시리얼 링크의 클락킹에 관여되는 주요한 문제들에 대하여 기술한다. 준속도, 다중 표준 구조들이 채택되고 있는 추세에 따라, 기존의 클라킹 방법은 낮은 비용의 구현의 관점에서 새로운 혁신을 필요로 한다. LC 공진기를 대신하여 능동 소자 발진기를 사용한 주파수 합성에 대하여 알아보고, 이에 발생하는 두가지 주요 문제점과 각각에 대한 해결 방안을 탐색한다. 각 제안 방법을 프로토타입 칩을 통해 그 효용성을 검증하고, 이어서 능동 소자 발진기가 미래의 고속 시리얼 링크의 클락킹에 사용될 가능성에 대해 검토한다. 첫번째 시연으로써, 고주파 고리 발진기의 높은 플리커 잡음을 완화시키기 위해 기준 신호를 배수화하여 뒷단의 위상 고정 루프의 대역폭을 효과적으로 극대화 시키는 회로 기술을 제안한다. 본 기술은 지터를 누적 시키지 않으며 따라서 깨끗한 중간 주파수 클락을 생성시켜 위상 고정 루프와 함께 높은 성능의 고주파 클락을 합성한다. 기준 신호를 성공적으로 배수화하기 위한 타이밍 조건들을 먼저 분석하여 타이밍 오류를 제거하기 위한 방법론을 파악한다. 각 교정 중량은 연역적 확률을 기반으로한 LMS 알고리즘을 통해 갱신되도록 설계된다. 교정에 필요한 시간을 최소화 하기 위하여, 각 교정 이득은 타이밍 오류 근원들의 크기를 귀납적으로 추론한 값을 바탕으로 지속적으로 제어된다. 40-nm CMOS 공정으로 구현된 프로토타입 칩의 측정을 통해 저소음, 고주파 클락을 빠른 교정 시간안에 합성해 냄을 확인하였다. 이는 177/223 fs의 rms 지터를 가지는 8/16 GHz의 클락을 출력한다. 두번째 시연으로써, 고리 발진기의 높은 전원 노이즈 의존성을 완화시키는 기술이 포함된 주파수 합성기가 설계되었다. 이는 고리 발진기의 전압 헤드룸을 보존함으로서 고주파 발진을 가능하게 한다. 나아가, 전원 노이즈 감소 성능은 공정, 전압, 온도 변동에 대하여 민감하지 않으며, 따라서 추가적인 교정 회로를 필요로 하지 않는다. 마지막으로, 위상 노이즈에 대한 포괄적 분석과 회로 최적화를 통하여 주파수 합성기의 저잡음 출력을 방해하지 않는 방법을 고안하였다. 해당 프로토타입 칩은 40-nm CMOS 공정으로 구현되었으며, 전원 노이즈가 인가되지 않은 상태에서 289 fs의 rms 지터를 가지는 8 GHz의 클락을 출력한다. 또한, 20 mVrms의 전원 노이즈가 인가되었을 때에 유도되는 지터의 양을 -23.8 dB 만큼 줄이는 것을 확인하였다.1 Introduction 1 1.1 Motivation 3 1.1.1 Clocking in High-Speed Serial Links 4 1.1.2 Multi-Phase, High-Frequency Clock Conversion 8 1.2 Dissertation Objectives 10 2 RO-Based High-Frequency Synthesis 12 2.1 Phase-Locked Loop Fundamentals 12 2.2 Toward All-Digital Regime 15 2.3 RO Design Challenges 21 2.3.1 Oscillator Phase Noise 21 2.3.2 Challenge 1: High Flicker Noise 23 2.3.3 Challenge 2: High Supply Noise Sensitivity 26 3 Filtering RO Noise 28 3.1 Introduction 28 3.2 Proposed Reference Octupler 34 3.2.1 Delay Constraint 34 3.2.2 Phase Error Calibration 38 3.2.3 Circuit Implementation 51 3.3 IL-ADPLL Implementation 55 3.4 Measurement Results 59 3.5 Summary 63 4 RO Supply Noise Compensation 69 4.1 Introduction 69 4.2 Proposed Analog Closed Loop for Supply Noise Compensation 72 4.2.1 Circuit Implementation 73 4.2.2 Frequency-Domain Analysis 76 4.2.3 Circuit Optimization 81 4.3 ADPLL Implementation 87 4.4 Measurement Results 90 4.5 Summary 98 5 Conclusions 99 A Notes on the 8REF 102 B Notes on the ACSC 105박

Design of High-Speed SerDes Transceiver for Chip-to-Chip Communications in CMOS Process

With the continuous increase of on-chip computation capacities and exponential growth of data-intensive applications, the high-speed data transmission through serial links has become the backbone for modern communication systems. To satisfy the massive data-exchanging requirement, the data rate of such serial links has been updated from several Gb/s to tens of Gb/s. Currently, the commercial standards such as Ethernet 400GbE, InfiniBand high data rate (HDR), and common electrical interface (CEI)-56G has been developing towards 40+ Gb/s. As the core component within these links, the transceiver chipset plays a fundamental role in balancing the operation speed, power consumption, area occupation, and operation range. Meanwhile, the CMOS process has become the dominant technology in modern transceiver chip fabrications due to its large-scale digital integration capability and aggressive pricing advantage. This research aims to explore advanced techniques that are capable of exploiting the maximum operation speed of the CMOS process, and hence provides potential solutions for 40+ Gb/s CMOS transceiver designs. The major contributions are summarized as follows. A low jitter ring-oscillator-based injection-locked clock multiplier (RILCM) with a hybrid frequency tracking loop that consists of a traditional phase-locked loop (PLL), a timing-adjusted loop, and a loop selection state-machine is implemented in 65-nm C-MOS process. In the ring voltage-controlled oscillator, a full-swing pseudo-differential delay cell is proposed to lower the device noise to phase noise conversion. To obtain high operation speed and high detection accuracy, a compact timing-adjusted phase detector tightly combined with a well-matched charge pump is designed. Meanwhile, a lock-loss detection and lock recovery is devised to endow the RILCM with a similar lock-acquisition ability as conventional PLL, thus excluding the initial frequency set- I up aid and preventing the potential lock-loss risk. The experimental results show that the figure-of-merit of the designed RILCM reaches -247.3 dB, which is better than previous RILCMs and even comparable to the large-area LC-ILCMs. The transmitter (TX) and receiver (RX) chips are separately designed and fab- ricated in 65-nm CMOS process. The transmitter chip employs a quarter-rate multi-multiplexer (MUX)-based 4-tap feed-forward equalizer (FFE) to pre-distort the output. To increase the maximum operating speed, a bandwidth-enhanced 4:1 MUX with the capability of eliminating charge-sharing effect is proposed. To produce the quarter-rate parallel data streams with appropriate delays, a compact latch array associated with an interleaved-retiming technique is designed. The receiver chip employs a two-stage continuous-time linear equalizer (CTLE) as the analog front-end and integrates an improved clock data recovery to extract the sampling clocks and retime the incoming data. To automatically balance the jitter tracking and jitter suppression, passive low-pass filters with adaptively-adjusted bandwidth are introduced into the data-sampling path. To optimize the linearity of the phase interpolation, a time-averaging-based compensating phase interpolator is proposed. For equalization, a combined TX-FFE and RX-CTLE is applied to compensate for the channel loss, where a low-cost edge-data correlation-based sign zero-forcing adaptation algorithm is proposed to automatically adjust the TX-FFE’s tap weights. Measurement results show that the fabricated transmitter/receiver chipset can deliver 40 Gb/s random data at a bit error rate of 16 dB loss at the half-baud frequency, while consuming a total power of 370 mW

Special Topics in Information Technology

This open access book presents thirteen outstanding doctoral dissertations in Information Technology from the Department of Electronics, Information and Bioengineering, Politecnico di Milano, Italy. Information Technology has always been highly interdisciplinary, as many aspects have to be considered in IT systems. The doctoral studies program in IT at Politecnico di Milano emphasizes this interdisciplinary nature, which is becoming more and more important in recent technological advances, in collaborative projects, and in the education of young researchers. Accordingly, the focus of advanced research is on pursuing a rigorous approach to specific research topics starting from a broad background in various areas of Information Technology, especially Computer Science and Engineering, Electronics, Systems and Control, and Telecommunications. Each year, more than 50 PhDs graduate from the program. This book gathers the outcomes of the thirteen best theses defended in 2019-20 and selected for the IT PhD Award. Each of the authors provides a chapter summarizing his/her findings, including an introduction, description of methods, main achievements and future work on the topic. Hence, the book provides a cutting-edge overview of the latest research trends in Information Technology at Politecnico di Milano, presented in an easy-to-read format that will also appeal to non-specialists

Wide-Dynamic Range Image Sensor Prototype Based On Digital Readout Integrated Circuit

Emerging infrared and visible imaging applications require higher sensitivity, larger pixel array, larger contrast ratio (dynamic range), very low power consumption and faster data readout rate operations all at the same time. Some of these applications are camera surveillance used both in day/night (very bright and dark conditions), medical diagnostics, weather forecasting, and aerial search & rescue operations etc. The digital-pixel focal plane array (DFPA) implemented in this thesis has the capabilities to capture a wide dynamic range of more than 120dB in a single global shutter without saturating the pixels at a huge frame rate of more than 500Hz. An adaptive Integration Window technique has been developed which ensures that we are able to measure such a huge dynamic range using a counter of only 10 bits (this helps us lower the power consumption of the design). This proposed image sensor has been designed, fabricated and tested in 65nm CMOS technology. It has 16 x 16-pixel array with 16 x 9 pixels with an inbuilt Silicon APD for optical testing and 16 x 7 dummy pixels for electrical testing. Our design proposes an off-chip digital calibration technique to cut down the burden on the analog circuitry. The sensor design achieved more than 128dB+ of dynamic range with a DNL/INL of 0.65/1.65 respectively with a power consumption of only 0.58 uW/pixel. The digital calibration scheme successfully cuts down the pixel-pixel variation standard deviations by a factor of 4. The proposed image sensor design should be able to address most of the short-comings of conventional FPAs and provides a one-shot solution to the design of high performance CMOS image sensors

Wide-Dynamic Range Image Sensor Prototype Based On Digital Readout Integrated Circuit

Emerging infrared and visible imaging applications require higher sensitivity, larger pixel array, larger contrast ratio (dynamic range), very low power consumption and faster data readout rate operations all at the same time. Some of these applications are camera surveillance used both in day/night (very bright and dark conditions), medical diagnostics, weather forecasting, and aerial search & rescue operations etc. The digital-pixel focal plane array (DFPA) implemented in this thesis has the capabilities to capture a wide dynamic range of more than 120dB in a single global shutter without saturating the pixels at a huge frame rate of more than 500Hz. An adaptive Integration Window technique has been developed which ensures that we are able to measure such a huge dynamic range using a counter of only 10 bits (this helps us lower the power consumption of the design). This proposed image sensor has been designed, fabricated and tested in 65nm CMOS technology. It has 16 x 16-pixel array with 16 x 9 pixels with an inbuilt Silicon APD for optical testing and 16 x 7 dummy pixels for electrical testing. Our design proposes an off-chip digital calibration technique to cut down the burden on the analog circuitry. The sensor design achieved more than 128dB+ of dynamic range with a DNL/INL of 0.65/1.65 respectively with a power consumption of only 0.58 uW/pixel. The digital calibration scheme successfully cuts down the pixel-pixel variation standard deviations by a factor of 4. The proposed image sensor design should be able to address most of the short-comings of conventional FPAs and provides a one-shot solution to the design of high performance CMOS image sensors

A Low-Jitter and Fractional-Resolution Injection-Locked Clock Multiplier Using a DLL-Based Real-time PVT-Calibrator with Replica-Delay Cells

A low-jitter and fractional-resolution injectionlocked clock multiplier (ILCM) with a delay-locked-loop (DLL)- based process-voltage-temperature (PVT)-calibrator is proposed. The ring-type voltage-controlled oscillator (VCO) and the voltagecontrolled delay line (VCDL) of the DLL consist of identical delay cells, and they share the same control voltage. Thus, by changing the ratio between the numbers of stages of the VCDL and the VCO, the frequency of the VCO can be calibrated at any target frequencies, noninteger times the reference frequency. As the amount of the unit delay is adjusted continuously by the DLL, the VCO can overcome real-time frequency drifts as well as static process variations; thus, excellent jitter performance can be sustained during any environmental variations. The proposed ILCM, designed in the 65 nm CMOS process, generated output frequenciesthat range from 1.2 to 2.0 GHz with a frequency resolution of 40 MHz and a 400 MHz reference clock. When injection locked, the integrated jitter from 1 kHz to 40 MHz of the 1.6 GHz signal was 440 fs. The proposed real-time PVT calibrator restricted the degradations of phase noise and jitter over the temperature and the supply variations to less than 0.7 dB and 20%, respectively. The active area was 0.032 mm2 and the power consumption was 3.6 mW.clos