Pipeline analog-to-digital converters for wide-band wireless communications

During the last decade, the development of the analog electronics has been dictated by the enormous growth of the wireless communications. Typical for the new communication standards has been an evolution towards higher data rates, which allows more services to be provided. Simultaneously, the boundary between analog and digital signal processing is moving closer to the antenna, thus aiming for a software defined radio. For analog-to-digital converters (ADCs) of radio receivers this indicates higher sample rate, wider bandwidth, higher resolution, and lower power dissipation. The radio receiver architectures, showing the greatest potential to meet the commercial trends, include the direct conversion receiver and the super heterodyne receiver with an ADC sampling at the intermediate frequency (IF). The pipelined ADC architecture, based on the switched capacitor (SC) technique, has most successfully covered the widely separated resolution and sample rate requirements of these receiver architectures. In this thesis, the requirements of ADCs in both of these receiver architectures are studied using the system specifications of the 3G WCDMA standard. From the standard and from the limited performance of the circuit building blocks, design constraints for pipeline ADCs, at the architectural and circuit level, are drawn. At the circuit level, novel topologies for all the essential blocks of the pipeline ADC have been developed. These include a dual-mode operational amplifier, low-power voltage reference circuits with buffering, and a floating-bulk bootstrapped switch for highly-linear IF-sampling. The emphasis has been on dynamic comparators: a new mismatch insensitive topology is proposed and measurement results for three different topologies are presented. At the architectural level, the optimization of the ADCs in the single-chip direct conversion receivers is discussed: the need for small area, low power, suppression of substrate noise, input and output interfaces, etc. Adaptation of the resolution and sample rate of a pipeline ADC, to be used in more flexible multi-mode receivers, is also an important topic included. A 6-bit 15.36-MS/s embedded CMOS pipeline ADC and an 8-bit 1/15.36-MS/s dual-mode CMOS pipeline ADC, optimized for low-power single-chip direct conversion receivers with single-channel reception, have been designed. The bandwidth of a pipeline ADC can be extended by employing parallelism to allow multi-channel reception. The errors resulted from mismatch of parallel signal paths are analyzed and their elimination is presented. Particularly, an optimal partitioning of the resolution between the stages, and the number of parallel channels, in time-interleaved ADCs are derived. A low-power 10-bit 200-MS/s CMOS parallel pipeline ADC employing double sampling and a front-end sample-and-hold (S/H) circuit is implemented. Emphasis of the thesis is on high-resolution pipeline ADCs with IF-sampling capability. The resolution is extended beyond the limits set by device matching by using calibration, while time interleaving is applied to widen the signal bandwidth. A review of calibration and error averaging techniques is presented. A simple digital self-calibration technique to compensate capacitor mismatch within a single-channel pipeline ADC, and the gain and offset mismatch between the channels of a time-interleaved ADC, is developed. The new calibration method is validated with two high-resolution BiCMOS prototypes, a 13-bit 50-MS/s single-channel and a 14-bit 160-MS/s parallel pipeline ADC, both utilizing a highly linear front-end allowing sampling from 200-MHz IF-band.reviewe

Design Techniques for High Speed Low Voltage and Low Power Non-Calibrated Pipeline Analog to Digital Converters

The profound digitization of modern microelectronic modules made Analog-to- Digital converters (ADC) key components in many systems. With resolutions up to 14bits and sampling rates in the 100s of MHz, the pipeline ADC is a prime candidate for a wide range of applications such as instrumentation, communications and consumer electronics. However, while past work focused on enhancing the performance of the pipeline ADC from an architectural standpoint, little has been done to individually address its fundamental building blocks. This work aims to achieve the latter by proposing design techniques to improve the performance of these blocks with minimal power consumption in low voltage environments, such that collectively high performance is achieved in the pipeline ADC. Towards this goal, a Recycling Folded Cascode (RFC) amplifier is proposed as an enhancement to the general performance of the conventional folded cascode. Tested in Taiwan Semiconductor Manufacturing Company (TSMC) 0.18?m Complementary Metal Oxide Semiconductor (CMOS) technology, the RFC provides twice the bandwidth, 8-10dB additional gain, more than twice the slew rate and improved noise performance over the conventional folded cascode-all at no additional power or silicon area. The direct auto-zeroing offset cancellation scheme is optimized for low voltage environments using a dual level common mode feedback (CMFB) circuit, and amplifier differential offsets up to 50mV are effectively cancelled. Together with the RFC, the dual level CMFB was used to implement a sample and hold amplifier driving a singleended load of 1.4pF and using only 2.6mA; at 200MS/s better than 9bit linearity is achieved. Finally a power conscious technique is proposed to reduce the kickback noise of dynamic comparators without resorting to the use of pre-amplifiers. When all techniques are collectively used to implement a 1Vpp 10bit 160MS/s pipeline ADC in Semiconductor Manufacturing International Corporation (SMIC) 0.18[mu]m CMOS, 9.2 effective number of bits (ENOB) is achieved with a near Nyquist-rate full scale signal. The ADC uses an area of 1.1mm2 and consumes 42mW in its analog core. Compared to recent state-of-the-art implementations in the 100-200MS/s range, the presented pipeline ADC uses the least power per conversion rated at 0.45pJ/conversion-step

Energy Efficient Techniques For Algorithmic Analog-To-Digital Converters

Analog-to-digital converters (ADCs) are key design blocks in state-of-art image, capacitive, and biomedical sensing applications. In these sensing applications, algorithmic ADCs are the preferred choice due to their high resolution and low area advantages. Algorithmic ADCs are based on the same operating principle as that of pipelined ADCs. Unlike pipelined ADCs where the residue is transferred to the next stage, an N-bit algorithmic ADC utilizes the same hardware N-times for each bit of resolution. Due to the cyclic nature of algorithmic ADCs, many of the low power techniques applicable to pipelined ADCs cannot be directly applied to algorithmic ADCs. Consequently, compared to those of pipelined ADCs, the traditional implementations of algorithmic ADCs are power inefficient. This thesis presents two novel energy efficient techniques for algorithmic ADCs. The first technique modifies the capacitors' arrangement of a conventional flip-around configuration and amplifier sharing technique, resulting in a low power and low area design solution. The other technique is based on the unit multiplying-digital-to-analog-converter approach. The proposed approach exploits the power saving advantages of capacitor-shared technique and capacitor-scaled technique. It is shown that, compared to conventional techniques, the proposed techniques reduce the power consumption of algorithmic ADCs by more than 85\%. To verify the effectiveness of such approaches, two prototype chips, a 10-bit 5 MS/s and a 12-bit 10 MS/s ADCs, are implemented in a 130-nm CMOS process. Detailed design considerations are discussed as well as the simulation and measurement results. According to the simulation results, both designs achieve figures-of-merit of approximately 60 fJ/step, making them some of the most power efficient ADCs to date