A Fully-Integrated Reconfigurable Dual-Band Transceiver for Short Range Wireless Communications in 180 nm CMOS

© 2015 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other users, including reprinting/ republishing this material for advertising or promotional purposes, creating new collective works for resale or redistribution to servers or lists, or reuse of any copyrighted components of this work in other works.A fully-integrated reconfigurable dual-band (760-960 MHz and 2.4-2.5 GHz) transceiver (TRX) for short range wireless communications is presented. The TRX consists of two individually-optimized RF front-ends for each band and one shared power-scalable analog baseband. The sub-GHz receiver has achieved the maximum 75 dBc 3rd-order harmonic rejection ratio (HRR3) by inserting a Q-enhanced notch filtering RF amplifier (RFA). In 2.4 GHz band, a single-ended-to-differential RFA with gain/phase imbalance compensation is proposed in the receiver. A ΣΔ fractional-N PLL frequency synthesizer with two switchable Class-C VCOs is employed to provide the LOs. Moreover, the integrated multi-mode PAs achieve the output P1dB (OP1dB) of 16.3 dBm and 14.1 dBm with both 25% PAE for sub-GHz and 2.4 GHz bands, respectively. A power-control loop is proposed to detect the input signal PAPR in real-time and flexibly reconfigure the PA's operation modes to enhance the back-off efficiency. With this proposed technique, the PAE of the sub-GHz PA is improved by x3.24 and x1.41 at 9 dB and 3 dB back-off powers, respectively, and the PAE of the 2.4 GHz PA is improved by x2.17 at 6 dB back-off power. The presented transceiver has achieved comparable or even better performance in terms of noise figure, HRR, OP1dB and power efficiency compared with the state-of-the-art.Peer reviewe

Label-controlled optical switching nodes

Optical networks are evolving from initially static optical circuits and subsequently optical circuit switching towards optical packet switching in order to take advan- tage of the high transport capacity made available by WDM systems in a more °exible and e±cient way. Optically labeling of packets and routing the packets's payload optically under control of its label allows the network nodes to route and forward IP data without having to process the payload, thus keeping it in the optical domain; this is a promising solution to avoid electronic bottlenecks in routers. All-optical label switching can therefore be used to route and forward packets independent of their length and payload bitrate. Several optical signal labeling techniques have been proposed in previous re- search reported in literature; orthogonal labeling and time-serial labeling have been studied in this thesis. This thesis studies two orthogonal modulation label- ing techniques: one based on FSK labels with an IM payload, and another one on SCM labeling for a DPSK modulated payload. A time-serial labeling method based on IM labels with IM or DPSK payload is also presented and studied. The ¯rst two techniques assume electronic processing of the labels in the node, and hence assume that labels can be transmitted at a much lower bitrate than the payload data rate. The third technique assumes all-optical signal processing in the nodes, capable of handling a label at the same bitrate or slightly lower than the payload data. Labels at low bitrate in comparison with the payload bitrate are desirable in systems where the label processing will be conducted in the electrical domain, while labels at the same bitrate as the payload can be used in systems where the processing is conducted in the optical domain, exploiting all-optical processing techniques. These three techniques have been chosen because they are compatible with the existing networks, since the modulation format, bitrates, transmission properties, and other features of the signals are similar to the ones used for commercially available applications. Thus, they can be considered important candidates for migration scenarios from optical circuit switching towards optical burst switching networking. Orthogonal labeling based on FSK/IM is a promising scheme for implementing the labeling of optical signals, and it is the technology of choice in the STOLAS project. This technique o®ers advantageous features such as a relaxed timing de- lineation between payload and label, and ease of label erasure and re-writing of new labels. By using wavelength-agile tunable laser sources with FSK modula- tion capability, wavelength converters, and passive wavelength routing elements, a scalable modular label-controlled router featuring high reliability can be built. In this thesis, several aspects of the physical parameters of an FSK/IM labeling scheme within a routing node have been studied and presented. Optical ¯ltering requires special care, since the combined FSK/IM scheme has a broader spectrum than that of pure intensity modulated signals. The requirements on the limited extinction ratio for the IM signal can be relaxed at low bitrates of the label signal or, alternatively, by introducing data encoding. Optical labeling by using FSK/IM represents a simple and attractive way of implementing hybrid optical circuit and burst switching in optical networks. Architecturally, similar advantages can be mentioned for the second orthogo- nal labeling technique studied in this thesis, based on SCM labels and a DPSK payload. In-band subcarriers carrying low bitrate labels located at a frequency equal to half the bitrate of the payload signal can be inserted introducing only low power penalties. Wavelength conversion can be implemented by using passive highly nonlinear ¯bers and exploiting the four-wave mixing e®ect. This thesis also studies the design of two functional blocks of an all-optical core node proposed in the LASAGNE project, namely the all-optical label and payload separator and the wavelength converter unit for a time-serial labeling scheme. The label and payload processor can be realized exploiting nonlinear e®ects in SOAs. An implementation using polarization division multiplexing to transport the external control light for an IM/IM time-serial scheme was demon- strated. Label and payload processors with self-contained control signals were also demonstrated, either using a DPSK signal to simultaneously transport the payload data and the control signal or inserting a CW dummy in between the label and the payload, which were based on IM-RZ format. A study on single- and multi- wavelength conversion based on FWM in a HNLF was presented. This approach allows transparent wavelength conversion (independent of the data format used) at high bitrates (the nonlinear e®ects in a ¯ber are obtained at ultrafast speeds). The labeling techniques explored have indicated a viable way of migration towards optical burst packet switched networks while signi¯cantly improving the throughput of the routing nodes

A Multi-Channel Low-Power System-on-Chip for in Vivo Recording and Wireless Transmission of Neural Spikes

This paper reports a multi-channel neural spike recording system-on-chip with digital data compression and wireless telemetry. The circuit consists of 16 amplifiers, an analog time-division multiplexer, a single 8 bit analog-to-digital converter, a digital signal compression unit and a wireless transmitter. Although only 16 amplifiers are integrated in our current die version, the whole system is designed to work with 64, demonstrating the feasibility of a digital processing and narrowband wireless transmission of 64 neural recording channels. Compression of the raw data is achieved by detecting the action potentials (APs) and storing 20 samples for each spike waveform. This compression method retains sufficiently high data quality to allow for single neuron identification (spike sorting). The 400 MHz transmitter employs a Manchester-Coded Frequency Shift Keying (MC-FSK) modulator with low modulation index. In this way, a 1.25 Mbit/s data rate is delivered within a limited band of about 3 MHz. The chip is realized in a 0.35 um AMS CMOS process featuring a 3 V power supply with an area of 3.1x 2.7 mm2. The achieved transmission range is over 10 m with an overall power consumption for 64 channels of 17.2 mW. This figure translates into a power budget of 269uW per channel, in line with published results but allowing a larger transmission distance and more efficient bandwidth occupation of the wireless link. The integrated circuit was mounted on a small and light board to be used during neuroscience experiments with freely-behaving rats. Powered by 2 AAA batteries, the system can continuously work for more than 100 hours allowing for long-lasting neural spike recordings

Coherent multicarrier lightwave technology for flexible capacity networks (invited)

Highly flexible and survivable networks can be built by allocating optical carriers of heterodyne systems. The basic features of heterodyne systems are reviewed, especially the use of multicarriers, tunability, and selectivity. Then specific application areas that may benefit from flexible multicarrier allocation schemes are discussed. Examples are taken from the RACE Phase II project R2065, coherent optical systems implemented for business traffic routing and access (COBRA). Next, trends and progress in heterodyne systems in general and related key components are summarized, and then examples of ongoing field trials in Europe are discussed. Finally, the coherent multicarrier technology are compared briefly with direct detection multiwavelength technolog

Design Considerations of a Sub-50 {\mu}W Receiver Front-end for Implantable Devices in MedRadio Band

Emerging health-monitor applications, such as information transmission through multi-channel neural implants, image and video communication from inside the body etc., calls for ultra-low active power (<50${\mu}$W) high data-rate, energy-scalable, highly energy-efficient (pJ/bit) radios. Previous literature has strongly focused on low average power duty-cycled radios or low power but low-date radios. In this paper, we investigate power performance trade-off of each front-end component in a conventional radio including active matching, down-conversion and RF/IF amplification and prioritize them based on highest performance/energy metric. The analysis reveals 50${\Omega}$ active matching and RF gain is prohibitive for 50${\mu}$W power-budget. A mixer-first architecture with an N-path mixer and a self-biased inverter based baseband LNA, designed in TSMC 65nm technology show that sub 50${\mu}$W performance can be achieved up to 10Mbps (< 5pJ/b) with OOK modulation.Comment: Accepted to appear on International Conference on VLSI Design 2018 (VLSID

Hybrid receiver study

The results are presented of a 4 month study to design a hybrid analog/digital receiver for outer planet mission probe communication links. The scope of this study includes functional design of the receiver; comparisons between analog and digital processing; hardware tradeoffs for key components including frequency generators, A/D converters, and digital processors; development and simulation of the processing algorithms for acquisition, tracking, and demodulation; and detailed design of the receiver in order to determine its size, weight, power, reliability, and radiation hardness. In addition, an evaluation was made of the receiver's capabilities to perform accurate measurement of signal strength and frequency for radio science missions