Design of Digital Frequency Synthesizer for 5G SDR Systems

The previous frequency synthesizer techniques for scalable SDR are not compatible with high end applications due to its complex computations and the intolerance over increased path interference rate which leads to an unsatisfied performance with improved user rate in real time environment. Designing an efficient frequency synthesizer framework in the SDR system is essential for 5G wireless communication systems with improved Quality of service (QoS). Consequently, this research has been performed based on the merits of fully digitalized frequency synthesizer and its explosion in wide range of frequency band generations. In this paper hardware optimized reconfigurable digital base band processing and frequency synthesizer model is proposed without making any design complexity trade-off to deal with the multiple standards. Here fully digitalized frequency synthesizer is introduced using simplified delay units to reduce the design complexity. Experimental results and comparative analyzes are carried out to validate the performance metrics and exhaustive test bench simulation is also carried out to verify the functionality

Clock Generator Circuits for Low-Power Heterogeneous Multiprocessor Systems-on-Chip

In this work concepts and circuits for local clock generation in low-power heterogeneous multiprocessor systems-on-chip (MPSoCs) are researched and developed. The targeted systems feature a globally asynchronous locally synchronous (GALS) clocking architecture and advanced power management functionality, as for example fine-grained ultra-fast dynamic voltage and frequency scaling (DVFS). To enable this functionality compact clock generators with low chip area, low power consumption, wide output frequency range and the capability for ultra-fast frequency changes are required. They are to be instantiated individually per core. For this purpose compact all digital phase-locked loop (ADPLL) frequency synthesizers are developed. The bang-bang ADPLL architecture is analyzed using a numerical system model and optimized for low jitter accumulation. A 65nm CMOS ADPLL is implemented, featuring a novel active current bias circuit which compensates the supply voltage and temperature sensitivity of the digitally controlled oscillator (DCO) for reduced digital tuning effort. Additionally, a 28nm ADPLL with a new ultra-fast lock-in scheme based on single-shot phase synchronization is proposed. The core clock is generated by an open-loop method using phase-switching between multi-phase DCO clocks at a fixed frequency. This allows instantaneous core frequency changes for ultra-fast DVFS without re-locking the closed loop ADPLL. The sensitivity of the open-loop clock generator with respect to phase mismatch is analyzed analytically and a compensation technique by cross-coupled inverter buffers is proposed. The clock generators show small area (0.0097mm2 (65nm), 0.00234mm2 (28nm)), low power consumption (2.7mW (65nm), 0.64mW (28nm)) and they provide core clock frequencies from 83MHz to 666MHz which can be changed instantaneously. The jitter performance is compliant to DDR2/DDR3 memory interface specifications. Additionally, high-speed clocks for novel serial on-chip data transceivers are generated. The ADPLL circuits have been verified successfully by 3 testchip implementations. They enable efficient realization of future low-power MPSoCs with advanced power management functionality in deep-submicron CMOS technologies.In dieser Arbeit werden Konzepte und Schaltungen zur lokalen Takterzeugung in heterogenen Multiprozessorsystemen (MPSoCs) mit geringer Verlustleistung erforscht und entwickelt. Diese Systeme besitzen eine global-asynchrone lokal-synchrone Architektur sowie Funktionalität zum Power Management, wie z.B. das feingranulare, schnelle Skalieren von Spannung und Taktfrequenz (DVFS). Um diese Funktionalität zu realisieren werden kompakte Taktgeneratoren benötigt, welche eine kleine Chipfläche einnehmen, wenig Verlustleitung aufnehmen, einen weiten Bereich an Ausgangsfrequenzen erzeugen und diese sehr schnell ändern können. Sie sollen individuell pro Prozessorkern integriert werden. Dazu werden kompakte volldigitale Phasenregelkreise (ADPLLs) entwickelt, wobei eine bang-bang ADPLL Architektur numerisch modelliert und für kleine Jitterakkumulation optimiert wird. Es wird eine 65nm CMOS ADPLL implementiert, welche eine neuartige Kompensationsschlatung für den digital gesteuerten Oszillator (DCO) zur Verringerung der Sensitivität bezüglich Versorgungsspannung und Temperatur beinhaltet. Zusätzlich wird eine 28nm CMOS ADPLL mit einer neuen Technik zum schnellen Einschwingen unter Nutzung eines Phasensynchronisierers realisiert. Der Prozessortakt wird durch ein neuartiges Phasenmultiplex- und Frequenzteilerverfahren erzeugt, welches es ermöglicht die Taktfrequenz sofort zu ändern um schnelles DVFS zu realisieren. Die Sensitivität dieses Frequenzgenerators bezüglich Phasen-Mismatch wird theoretisch analysiert und durch Verwendung von kreuzgekoppelten Taktverstärkern kompensiert. Die hier entwickelten Taktgeneratoren haben eine kleine Chipfläche (0.0097mm2 (65nm), 0.00234mm2 (28nm)) und Leistungsaufnahme (2.7mW (65nm), 0.64mW (28nm)). Sie stellen Frequenzen von 83MHz bis 666MHz bereit, welche sofort geändert werden können. Die Schaltungen erfüllen die Jitterspezifikationen von DDR2/DDR3 Speicherinterfaces. Zusätzliche können schnelle Takte für neuartige serielle on-Chip Verbindungen erzeugt werden. Die ADPLL Schaltungen wurden erfolgreich in 3 Testchips erprobt. Sie ermöglichen die effiziente Realisierung von zukünftigen MPSoCs mit Power Management in modernsten CMOS Technologien

적응형 눈 감지 방법을 포함한 저전력 메모리 컨트롤러의 설계

학위논문 (박사)-- 서울대학교 대학원 공과대학 전기·컴퓨터공학부, 2017. 8. 김수환.and the read margin was enhanced from 0.30UI and 76mV without AF-CTLE to 0.47UI and 80mV to with AF-CTLE. The power efficiency during burst write and read were 5.68pJ/bit and 1.83pJ/bit respectively.A 4266Mb/s/pin LPDDR4 memory controller with an asynchronous feedback continuous-time linear equalizer and an adaptive 3-step eye detection algorithm is presented. The asynchronous feedback continuous-time linear equalizer removes the glitch of DQS without training by applying an offset larger than the noise, and improves read margin by operating as a decision feedback equalizer in DQ path. The adaptive 3-step eye detection algorithm reduces power consumption and black-out time in initialization sequence and retraining in comparison to the 2-dimensional full scanning. In addition, the adaptive 3-step eye detection algorithm can maintain the accuracy by sequentially searching the eye boundaries and initializing the resolution using the binary search method when the eye detection result changes. To achieve high bandwidth, a transmitter and receiver suitable for training are proposed. The transmitter consists of a phase interpolator, a digitally-controlled delay line, a 16:1 serializer, a pre-driver and low-voltage swing terminated logic. The receiver consists of a reference voltage generator, a continuous-time linear equalizer, a phase interpolator, a digitally-controlled delay line, a 1:4 deserializer, and a 4:16 deserializer. The clocking architecture is also designed for low power consumption in idle periods, which are commonly lengthy in mobile applications. A prototype chip was implemented in a 65nm CMOS process with ball grid array package and tested with commodity LPDDR4. The write margin was 0.36UI and 148mVCHAPTER 1 INTRODUCTION 1 1.1 MOTIVATION 1 1.2 THESIS ORGANIZATION 5 CHAPTER 2 LPDDR4 6 2.1 COMPARISON BETWEEN LPDDR3 AND LPDDR4 6 2.2 SOURCE SYNCHRONOUS CLOCKING SCHEME 9 2.3 SIGNALING STANDARDS 11 2.4 MULTIPLE TRAININGS 14 2.5 RE-TRAINING AND RE-INITIALIZATION 16 CHAPTER 3 ADAPTIVE EYE DETECTION 18 3.1 EYE DETECTION 18 3.2 1X2Y3X EYE DETECTION 20 3.3 ADAPTIVE GAIN CONTROL 22 3.4 ADAPTIVE 1X2Y3X EYE DETECTION 24 CHAPTER 4 LPDDR4 MEMORY CONTROLLER 26 4.1 DESIGN PROCEDURE 26 4.2 ARCHITECTURE 30 4.2.1 TRANSMITTER 33 4.2.2 RECEIVER 35 4.2.3 CLOCKING ARCHITECTURE 38 4.3 CIRCUIT IMPLEMENTATION 43 4.3.1 ADPLL WITH MULTI-MODULUS DIVIDER 43 4.3.2 ADDLL WITH TRIANGULAR-MODULATED PI 45 4.3.3 CTLE WITH AUTO-DQS CLEANING 47 4.3.4 DES WITH CLOCK DOMAIN CROSSING 52 4.3.5 LVSTL WITH ZQ CALIBRATION 54 4.3.6 COARSE-FINE DCDL 56 4.4 LINK TRAINING 57 4.4.1 SIMULATION RESULTS 59 CHAPTER 5 MEASUREMENT RESULTS 72 5.1 MEASUREMENT SETUP 72 5.2 MEASUREMENT RESULTS OF SUB-BLOCK 80 5.2.1 ADPLL WITH MULTI-MODULUS DIVIDER 80 5.2.2 ADDLL WITH TRIANGULAR-MODULATED PI 82 5.2.3 COARSE-FINE DCDL 84 5.3 LPDDR4 INTERFACE MEASUREMENT RESULTS 84 CHAPTER 6 CONCLUSION 88 BIBLIOGRAPHY 90Docto

Design of Low Power, High Speed Frequency Multiplier Based On DPLL for Clock Generation

A low-power and high-speed frequency multiplier for a DPLL-based clock generator is proposed to produce a multiplied clock with a high frequency and a greatest frequency rang. The proposed frequency multiplier devours low power and accomplishes a rapid activity. The proposed frequency multiplier minimizes the delay difference between the positive and negative edge generation paths. This is fabricated in a 0.12μm CMOS process technology and accomplished power utilization to a frequency ratio of 0.698mw, and it generates 59 phase differential clocksand has the maximum multiplication ratio of 33, and an output range of 100MHz

펄스 기반 피드 포워드 이퀄라이저를 갖춘 고용량 DRAM을 위한 컨트롤러 PHY 설계

학위논문 (박사) -- 서울대학교 대학원 : 공과대학 전기·정보공학부, 2020. 8. 김수환.A controller PHY for managed DRAM solution, which is a new memory structure to maximize capacity while minimizing refresh power, is presented. Inter-symbol interference is critical in such a high-capacity DRAM interface in which many DRAM chips share a command/address (C/A) channel. A pulse-based feed-forward equalizer (PB-FFE) is introduced to reduce ISI on a C/A channel. The controller PHY supports all the training sequences specified in the DDR4 standard. A glitch-free DCDL is also adopted to perform link training efficiently and to reduce training time. The DQ transmitter adopts quarter-rate architecture to reduce output latency. For the quarter-rate transmitters in DQ, we propose a quadrature error corrector (QEC), in which clock signal phase errors are corrected using two replicas of the 4:1 serializer of the output stage. Pulse shrinking is used to compare and equalize the outputs of these two replica serializers. A controller PHY was fabricated in 55nm CMOS. The PB-FFE increases the timing margin from 0.23UI to 0.29UI at 1067Mbps. At 2133Mbps, the read timing and voltage margins are 0.53UI and 211mV after read training, and the write margins are 0.72UI and 230mV after write training. To validate the QEC effectiveness, a prototype quarter-rate transmitter, including the QEC, was fabricated to another chip in 65nm CMOS. Adopting our QEC, the experimental results show that the output phase errors of the transmitter are reduced to a residual error of 0.8ps, and the output eye width and height are improved by 84% and 61%, respectively, at a data-rate of 12.8Gbps.본 연구에서 용량을 최대화하면서도 리프레시 전력을 최소화할 수 있는 새로운 메모리 구조인 관리형 DRAM 솔루션을 위한 컨트롤러 PHY를 제시하였다. 이와 같은 고용량 DRAM 인터페이스에서는 많은 DRAM 칩이 명령 / 주소 (C/A) 채널을 공유하고 있어서 심볼 간 간섭이 발생한다. 본 연구에서는 이러한 C/A 채널에서의 심볼 간 간섭을 줄이기 위해 펄스 기반 피드 포워드 이퀄라이저 (PB-FFE)를 채택하였다. 또한 본 연구의 컨트롤러 PHY는 DDR4 표준에 지정된 모든 트레이닝 시퀀스를 지원한다. 링크 트레이닝을 효율적으로 수행하고 트레이닝 시간을 줄이기 위해 글리치가 발생하지 않는 디지털 제어 지연 라인 (DCDL)을 채택하였다. 컨트롤러 PHY의 DQ 송신기는 출력 대기 시간을 줄이기 위해 쿼터 레이트 구조를 채택하였다. 쿼터 레이트 송신기의 경우에는 직교 클럭 간 위상 오류가 출력 신호의 무결성에 영향을 주게 된다. 이러한 영향을 최소화하기 위해 본 연구에서는 출력 단의 4 : 1 직렬 변환기의 두 복제본을 사용하여 클록 신호 위상 오류를 수정하는 QEC (Quadrature Error Corrector)를 제안하였다. 복제된 2개의 직렬 변환기의 출력을 비교하고 균등화하기 위해 펄스 수축 지연 라인이 사용되었다. 컨트롤러 PHY는 55nm CMOS 공정으로 제조되었다. PB-FFE는 1067Mbps에서 C/A 채널 타이밍 마진을 0.23UI에서 0.29UI로 증가시킨다. 읽기 트레이닝 후 읽기 타이밍 및 전압 마진은 2133Mbps에서 0.53UI 및 211mV이고, 쓰기 트레이닝 후 쓰기 마진은 0.72UI 및 230mV이다. QEC의 효과를 검증하기 위해 QEC를 포함한 프로토 타입 쿼터 레이트 송신기를 65nm CMOS의 다른 칩으로 제작하였다. QEC를 적용한 실험 결과, 송신기의 출력 위상 오류가 0.8ps의 잔류 오류로 감소하고, 출력 데이터 눈의 폭과 높이가 12.8Gbps의 데이터 속도에서 각각 84 %와 61 % 개선되었음을 보여준다.CHAPTER 1 INTRODUCTION 1 1.1 MOTIVATION 1 1.1.1 HEAVY LOAD C/A CHANNEL 5 1.1.2 QUARTER-RATE ARCHITECTURE IN DQ TRANSMITTER 7 1.1.3 SUMMARY 8 1.2 THESIS ORGANIZATION 10 CHAPTER 2 ARCHITECTURE 11 2.1 MDS DIMM STRUCTURE 11 2.2 MDS CONTROLLER 15 2.3 MDS CONTROLLER PHY 17 2.3.1 INITIALIZATION SEQUENCE 20 2.3.2 LINK TRAINING FINITE-STATE MACHINE 23 2.3.3 POWER DOWN MODE 28 CHAPTER 3 PULSE-BASED FEED-FORWARD EQUALIZER 29 3.1 COMMAND/ADDRESS CHANNEL 29 3.2 COMMAND/ADDRESS TRANSMITTER 33 3.3 PULSE-BASED FEED-FORWARD EQUALIZER 35 CHAPTER 4 CIRCUIT IMPLEMENTATION 39 4.1 BUILDING BLOCKS 39 4.1.1 ALL-DIGITAL PHASE-LOCKED LOOP (ADPLL) 39 4.1.2 ALL-DIGITAL DELAY-LOCKED LOOP (ADDLL) 44 4.1.3 GLITCH-FREE DCDL CONTROL 47 4.1.4 DUTY-CYCLE CORRECTOR (DCC) 50 4.1.5 DQ/DQS TRANSMITTER 52 4.1.6 DQ/DQS RECEIVER 54 4.1.7 ZQ CALIBRATION 56 4.2 MODELING AND VERIFICATION OF LINK TRAINING 59 4.3 BUILT-IN SELF-TEST CIRCUITS 66 CHAPTER 5 QUADRATURE ERROR CORRECTOR USING REPLICA SERIALIZERS AND PULSE-SHRINKING DELAY LINES 69 5.1 PHASE CORRECTION USING REPLICA SERIALIZERS AND PULSE-SHRINKING UNITS 69 5.2 OVERALL QEC ARCHITECTURE AND ITS OPERATION 71 5.3 FINE DELAY UNIT IN THE PSDL 76 CHAPTER 6 EXPERIMENTAL RESULTS 78 6.1 CONTROLLER PHY 78 6.2 PROTOTYPE QEC 88 CHAPTER 7 CONCLUSION 94 BIBLIOGRAPHY 96Docto