403 research outputs found
A low-cost time-hopping impulse radio system for high data rate transmission
We present an efficient, low-cost implementation of time-hopping impulse
radio that fulfills the spectral mask mandated by the FCC and is suitable for
high-data-rate, short-range communications. Key features are: (i) all-baseband
implementation that obviates the need for passband components, (ii) symbol-rate
(not chip rate) sampling, A/D conversion, and digital signal processing, (iii)
fast acquisition due to novel search algorithms, (iv) spectral shaping that can
be adapted to accommodate different spectrum regulations and interference
environments. Computer simulations show that this system can provide 110Mbit/s
at 7-10m distance, as well as higher data rates at shorter distances under FCC
emissions limits. Due to the spreading concept of time-hopping impulse radio,
the system can sustain multiple simultaneous users, and can suppress narrowband
interference effectively.Comment: To appear in EURASIP Journal on Applied Signal Processing (Special
Issue on UWB - State of the Art
Accurate Positioning in Ultra-Wideband Systems
Cataloged from PDF version of article.Accurate positioning systems can be realized via ultra-wideband signals due to their high time resolution. In this article, position estimation is studied for UWB systems. After a brief introduction to UWB signals and their positioning applications,
two-step positioning systems are investigated from a UWB perspective. It is observed that time-based positioning is well suited for UWB systems. Then time-based UWB ranging is studied in detail, and the main challenges, theoretical limits, and range estimation algorithms are presented. Performance of some practical time-based ranging algorithms is investigated and compared against the maximum likelihood estimator and the theoretical limits. The trade-off between complexity and accuracy is .observe
Ultra Wideband Indoor Navigation System
Typical indoor environments contain multiple walls and obstacles consisting of different materials. As a result, current narrowband radio frequency (RF) indoor navigation systems cannot satisfy the challenging demands for most indoor applications. The RF ultra wideband (UWB) system is a promising technology for indoor localisation owing to its high bandwidth that permits mitigation of the multipath identification problem. This work proposes a novel UWB navigation system that permits accurate mobile robot (MR) navigation in indoor environments. The navigation system is composed of two sub-systems: the localisation system and the MR control system. The main contributions of this work are focused on estimation algorithm for localisation, digital implementation of transmitter and receiver and integration of both sub-systems that enable autonomous robot navigation. For sub-systems performance evaluation, statics and dynamics experiments were carried out which demonstrated that the proposed system reached an accuracy that outperforms traditional sensors technologies used in robot navigation, such as odometer and sonar.Fil: Segura M.. Universidad Nacional de San Juan; ArgentinaFil: Mut, Vicente Antonio. Universidad Nacional de San Juan; Argentina. Consejo Nacional de Investigaciones CientĂficas y TĂ©cnicas; ArgentinaFil: Sisterna C.. Universidad Nacional de San Juan; Argentin
Ultra Wideband Communications: from Analog to Digital
ï»żUltrabreitband-Signale (Ultra Wideband [UWB]) können einen
signifikanten Nutzen im Bereich drahtloser Kommunikationssysteme haben. Es
sind jedoch noch einige Probleme offen, die durch Systemdesigner und
Wissenschaftler gelöst werden mĂŒssen. Ein Funknetzsystem mit einer derart
groĂen Bandbreite ist normalerweise auch durch eine groĂe Anzahl an
Mehrwegekomponenten mit jeweils verschiedenen Pfadamplituden
gekennzeichnet. Daher ist es schwierig, die zeitlich verteilte Energie
effektiv zu erfassen. AuĂerdem ist in vielen FĂ€llen der naheliegende
Ansatz, ein kohÀrenter EmpfÀnger im Sinne eines signalangepassten Filters
oder eines Korrelators, nicht unbedingt die beste Wahl. In der vorliegenden
Arbeit wird dabei auf die bestehende Problematik und weitere
Lösungsmöglichkeiten eingegangen.
Im ersten Abschnitt geht es um âImpulse Radio UWBâ-Systeme mit
niedriger Datenrate. Bei diesen Systemen kommt ein inkohÀrenter EmpfÀnger
zum Einsatz. InkohÀrente Signaldetektion stellt insofern einen
vielversprechenden Ansatz dar, als das damit aufwandsgĂŒnstige und robuste
Implementierungen möglich sind. Dies trifft vor allem in AnwendungsfÀllen
wie den von drahtlosen Sensornetzen zu, wo preiswerte GerÀte mit langer
Batterielaufzeit nötigsind. Dies verringert den fĂŒr die KanalschĂ€tzung
und die Synchronisation nötigen Aufwand, was jedoch auf Kosten der
Leistungseffizienz geht und eine erhöhte Störempfindlichkeit gegenĂŒber
Interferenz (z.B. Interferenz durch mehrere Nutzer oder schmalbandige
Interferenz) zur Folge hat.
Um die Bitfehlerrate der oben genannten Verfahren zu bestimmen, wurde
zunÀchst ein inkohÀrenter Combining-Verlust spezifiziert, welcher
auftritt im Gegensatz zu kohÀrenter Detektion mit Maximum Ratio Multipath
Combining. Dieser Verlust hÀngt von dem Produkt aus der LÀnge des
Integrationsfensters und der Signalbandbreite ab.
Um den Verlust durch inkohÀrentes Combining zu reduzieren und somit die
Leistungseffizienz des EmpfÀngers zu steigern, werden verbesserte
Combining-Methoden fĂŒr Mehrwegeempfang vorgeschlagen. Ein analoger
EmpfÀnger, bei dem der Hauptteil des Mehrwege-Combinings durch einen
âIntegrate and Dumpâ-Filter implementiert ist, wird fĂŒr UWB-Systeme
mit Zeit-Hopping gezeigt. Dabei wurde die Einsatzmöglichkeit von dĂŒnn
besetzten Codes in solchen System diskutiert und bewertet. Des Weiteren
wird eine Regel fĂŒr die Code-Auswahl vorgestellt, welche die StabilitĂ€t
des Systems gegen Mehrnutzer-Störungen sicherstellt und gleichzeitig den
Verlust durch inkohÀrentes Combining verringert.
Danach liegt der Fokus auf digitalen Lösungen bei inkohÀrenter
Demodulation. Im Vergleich zum AnalogempfÀnger besitzt ein
DigitalempfÀnger einen Analog-Digital-Wandler im Zeitbereich gefolgt von
einem digitalen Optimalfilter. Der digitale Optimalfilter dekodiert den
Mehrfachzugriffscode kohÀrent und beschrÀnkt das inkohÀrente Combining
auf die empfangenen Mehrwegekomponenten im Digitalbereich. Es kommt ein
schneller Analog-Digital-Wandler mit geringer Auflösung zum Einsatz, um
einen vertretbaren Energieverbrauch zu gewÀhrleisten. Diese Digitaltechnik
macht den Einsatz langer Analogverzögerungen bei differentieller
Demodulation unnötig und ermöglicht viele Arten der digitalen
Signalverarbeitung. Im Vergleich zur Analogtechnik reduziert sie nicht nur
den inkohÀrenten Combining-Verlust, sonder zeigt auch eine stÀrkere
Resistenz gegenĂŒber Störungen. Dabei werden die Auswirkungen der
Auflösung und der Abtastrate der Analog-Digital-Umsetzung analysiert. Die
Resultate zeigen, dass die verminderte Effizienz solcher
Analog-Digital-Wandler gering ausfÀllt. Weiterhin zeigt sich, dass im
Falle starker Mehrnutzerinterferenz sogar eine Verbesserung der Ergebnisse
zu beobachten ist. Die vorgeschlagenen Design-Regeln spezifizieren die
Anwendung der Analog-Digital-Wandler und die Auswahl der Systemparameter in
AbhÀngigkeit der verwendeten Mehrfachzugriffscodes und der Modulationsart.
Wir zeigen, wie unter Anwendung erweiterter Modulationsverfahren die
Leistungseffizienz verbessert werden kann und schlagen ein Verfahren zur
UnterdrĂŒckung schmalbandiger Störer vor, welches auf Soft Limiting
aufbaut. Durch die Untersuchungen und Ergebnissen zeigt sich, dass
inkohÀrente EmpfÀnger in UWB-Kommunikationssystemen mit niedriger
Datenrate ein groĂes Potential aufweisen.
AuĂerdem wird die Auswahl der benutzbaren Bandbreite untersucht, um einen
Kompromiss zwischen inkohÀrentem Combining-Verlust und StabilitÀt
gegenĂŒber langsamen Schwund zu erreichen. Dadurch wurde ein neues Konzept
fĂŒr UWB-Systeme erarbeitet: wahlweise kohĂ€rente oder inkohĂ€rente
EmpfÀnger, welche als UWB-Systeme Frequenz-Hopping nutzen. Der wesentliche
Vorteil hiervon liegt darin, dass die Bandbreite im Basisband sich deutlich
verringert. Mithin ermöglicht dies einfach zu realisierende digitale
Signalverarbeitungstechnik mit kostengĂŒnstigen Analog-Digital-Wandlern.
Dies stellt eine neue Epoche in der Forschung im Bereich drahtloser
Sensorfunknetze dar.
Der Schwerpunkt des zweiten Abschnitts stellt adaptiven Signalverarbeitung
fĂŒr hohe Datenraten mit âDirect Sequenceâ-UWB-Systemen in den
Vordergrund. In solchen Systemen entstehen, wegen der groĂen Anzahl der
empfangenen Mehrwegekomponenten, starke Inter- bzw.
Intrasymbolinterferenzen. AuĂerdem kann die FunktionalitĂ€t des Systems
durch Mehrnutzerinterferenz und Schmalbandstörungen deutlich beeinflusst
werden. Um sie zu eliminieren, wird die âWidely Linearâ-Rangreduzierung
benutzt. Dabei verbessert die Rangreduzierungsmethode das
Konvergenzverhalten, besonders wenn der gegebene Vektor eine sehr groĂe
Anzahl an Abtastwerten beinhaltet (in Folge hoher einer Abtastrate).
ZusÀtzlich kann das System durch die Anwendung der R-linearen Verarbeitung
die Statistik zweiter Ordnung des nicht-zirkularen Signals vollstÀndig
ausnutzen, was sich in verbesserten SchÀtzergebnissen widerspiegelt.
Allgemeine kann die Methode der âWidely Linearâ-Rangreduzierung auch in
andern Bereichen angewendet werden, z.B. in âDirect
Sequenceâ-Codemultiplexverfahren (DS-CDMA), im MIMO-Bereich, im Global
System for Mobile Communications (GSM) und beim Beamforming.The aim of this thesis is to investigate key issues encountered in the
design of transmission schemes and receiving techniques for Ultra Wideband
(UWB) communication systems. Based on different data rate applications,
this work is divided into two parts, where energy efficient and robust
physical layer solutions are proposed, respectively.
Due to a huge bandwidth of UWB signals, a considerable amount of multipath
arrivals with various path gains is resolvable at the receiver. For low
data rate impulse radio UWB systems, suboptimal non-coherent detection is a
simple way to effectively capture the multipath energy. Feasible techniques
that increase the power efficiency and the interference robustness of
non-coherent detection need to be investigated. For high data rate direct
sequence UWB systems, a large number of multipath arrivals results in
severe inter-/intra-symbol interference. Additionally, the system
performance may also be deteriorated by multi-user interference and
narrowband interference. It is necessary to develop advanced signal
processing techniques at the receiver to suppress these interferences.
Part I of this thesis deals with the co-design of signaling schemes and
receiver architectures in low data rate impulse radio UWB systems based on
non-coherent detection.â We analyze the bit error rate performance of
non-coherent detection and characterize a non-coherent combining loss,
i.e., a performance penalty with respect to coherent detection with maximum
ratio multipath combining. The thorough analysis of this loss is very
helpful for the design of transmission schemes and receive techniques
innon-coherent UWB communication systems.â We propose to use optical
orthogonal codes in a time hopping impulse radio UWB system based on an
analog non-coherent receiver. The âanalogâ means that the major part of
the multipath combining is implemented by an integrate and dump filter. The
introduced semi-analytical method can help us to easily select the time
hopping codes to ensure the robustness against the multi-user interference
and meanwhile to alleviate the non-coherent combining loss.â The main
contribution of Part I is the proposal of applying fully digital solutions
in non-coherent detection. The proposed digital non-coherent receiver is
based on a time domain analog-to-digital converter, which has a high speed
but a very low resolution to maintain a reasonable power consumption.
Compared to its analog counterpart, itnot only significantly reduces the
non-coherent combining loss but also offers a higher interference
robustness. In particular, the one-bit receiver can effectively suppress
strong multi-user interference and is thus advantageous in separating
simultaneously operating piconets.The fully digital solutions overcome the
difficulty of implementing long analog delay lines and make differential
UWB detection possible. They also facilitate the development of various
digital signal processing techniques such as multi-user detection and
non-coherent multipath combining methods as well as the use of advanced
modulationschemes (e.g., M-ary Walsh modulation).â Furthermore, we
present a novel impulse radio UWB system based on frequency hopping, where
both coherent and non-coherent receivers can be adopted. The key advantage
is that the baseband bandwidth can be considerably reduced (e.g., lower
than 500 MHz), which enables low-complexity implementation of the fully
digital solutions. It opens up various research activities in the
application field of wireless sensor networks.
Part II of this thesis proposes adaptive widely linear reduced-rank
techniques to suppress interferences for high data rate direct sequence UWB
systems, where second-order non-circular signals are used. The reduced-rank
techniques are designed to improve the convergence performance and the
interference robustness especially when the received vector contains a
large number of samples (due to a high sampling rate in UWB systems). The
widely linear processing takes full advantage of the second-order
statistics of the non-circular signals and enhances the estimation
performance. The generic widely linear reduced-rank concept also has a
great potential in the applications of other systems such as Direct
Sequence Code Division Multiple Access (DS-CDMA), Multiple Input Multiple
Output (MIMO) system, and Global System for Mobile Communications (GSM), or
in other areas such as beamforming
Doctor of Philosophy
dissertationDevice-free localization (DFL) and tracking services are important components in security, emergency response, home and building automation, and assisted living applications where an action is taken based on a person's location. In this dissertation, we develop new methods and models to enable and improve DFL in a variety of radio frequency sensor network configurations. In the first contribution of this work, we develop a linear regression and line stabbing method which use a history of line crossing measurements to estimate the track of a person walking through a wireless network. Our methods provide an alternative approach to DFL in wireless networks where the number of nodes that can communicate with each other in a wireless network is limited and traditional DFL methods are ill-suited. We then present new methods that enable through-wall DFL when nodes in the network are in motion. We demonstrate that we can detect when a person crosses between ultra-wideband radios in motion based on changes in the energy contained in the first few nanoseconds of a measured channel impulse response. Through experimental testing, we show how our methods can localize a person through walls with transceivers in motion. Next, we develop new algorithms to localize boundary crossings when a person crosses between multiple nodes simultaneously. We experimentally evaluate our algorithms with received signal strength (RSS) measurements collected from a row of radio frequency (RF) nodes placed along a boundary and show that our algorithms achieve orders of magnitude better localization classification than baseline DFL methods. We then present a way to improve the models used in through-wall radio tomographic imaging with E-shaped patch antennas we develop and fabricate which remain tuned even when placed against a dielectric. Through experimentation, we demonstrate the E-shaped patch antennas lower localization error by 44% compared with omnidirectional and microstrip patch antennas. In our final contribution, we develop a new mixture model that relates a link's RSS as a function of a person's location in a wireless network. We develop new localization methods that compute the probabilities of a person occupying a location based on our mixture model. Our methods continuously recalibrate the model to achieve a low localization error even in changing environments
- âŠ