Cross-Layer measurement on an IEEE 802.11g wireless network supporting MPEG-2 video streaming applications in the presence of interference

The performance of wireless local area networks supporting video streaming applications, based on MPEG-2 video codec, in the presence of interference is here dealt with. IEEE 802.11g standard wireless networks, that do not support QoS in according with IEEE 802.11e standard, are, in particular, accounted for and Bluetooth signals, additive white Gaussian noise, and competitive data traffic are considered as sources of interference. The goal is twofold: from one side, experimentally assessing and correlating the values that some performance metrics assume at the same time at different layers of an IEEE 802.11g WLAN delivering video streaming in the presence of in-channel interference; from the other side, deducing helpful and practical hints for designers and technicians, in order to efficiently assess and enhance the performance of an IEEE 802.11g WLAN supporting video streaming in some suitable setup conditions and in the presence of interference. To this purpose, an experimental analysis is planned following a cross-layer measurement approach, and a proper testbed within a semianechoic chamber is used. Valuable results are obtained in terms of signal-to-interference ratio, packet loss ratio, jitter, video quality, and interference data rate; helpful hints for designers and technicians are finally gained

Scalable and rate adaptive wireless multimedia multicast

The methods that are described in this work enable highly efficient audio-visual streaming over wireless digital communication systems to an arbitrary number of receivers. In the focus of this thesis is thus point-to-multipoint transmission at constrained end-to-end delay. A fundamental difference as compared to point-to-point connections between exactly two communicating sending and receiving stations is in conveying information about successful or unsuccessful packet reception at the receiver side. The information to be transmitted is available at the sender, whereas the information about successful reception is only available to the receiver. Therefore, feedback about reception from the receiver to the sender is necessary. This information may be used for simple packet repetition in case of error, or adaptation of the bit rate of transmission to the momentary bit rate capacity of the channel, or both. This work focuses on the single transmission (including retransmissions) of data from one source to multiple destinations at the same time. A comparison with multi-receiver sequentially redundant transmission systems (simulcast MIMO) is made. With respect to feedback, this work considers time division multiple access systems, in which a single channel is used for data transmission and feedback. Therefore, the amount of time that can be spent for transmitting feedback is limited. An increase in time used for feedback transmissions from potentially many receivers results in a decrease in residual time which is usable for data transmission. This has direct impact on data throughput and hence, the quality of service. In the literature, an approach to reduce feedback overhead which is based on simultaneous feedback exists. In the scope of this work, simultaneous feedback implies equal carrier frequency, bandwidth and signal shape, in this case orthogonal frequency-division multiplex signals, during the event of the herein termed feedback aggregation in time. For this scheme, a constant amount of time is spent for feedback, independent of the number of receivers giving feedback about reception. Therefore, also data throughput remains independent of the number of receivers. This property of audio-visual digital transmission is taken for granted for statically configured, single purpose systems, such as terrestrial television. In the scope of this work are, however, multi-user and multi-purpose digital communication networks. Wireless LANs are a well-known example and are covered in detail herein. In suchlike systems, it is of great importance to remain independent of the number of receivers, as otherwise the service of ubiquitous digital connectivity is at the risk of being degraded. In this regard, the thesis at hand elaborates at what bit rates audio-visual transmission to multiple receivers may take place in conjunction with feedback aggregation. It is shown that the scheme achieves a multi-user throughput gain when used in conjunction with adaptivity of the bit rate to the channel. An assumption is the use of an ideal overlay packet erasure correcting code in this case. Furthermore, for delay constrained transmission, such as in so-called live television, throughput bit rates are examined. Applications have to be tolerant to a certain level of residual error in case of delay constrained transmission. Improvement of the rate adaptation algorithm is shown to increase throughput while residual error rates are decreased. Finally, with a consumer hardware prototype for digital live-TV re-distribution in the local wireless network, most of the mechanisms as described herein can be demonstrated.Die in vorliegender Arbeit aufgezeigten Methoden der paketbasierten drahtlosen digitalen Kommunikation ermöglichen es, Fernsehinhalte, aber auch audio-visuelle Datenströme im Allgemeinen, bei hoher Effizienz an beliebig große Gruppen von Empfängern zu verteilen. Im Fokus dieser Arbeit steht damit die Punkt- zu Mehrpunktübertragung bei begrenzter Ende-zu-Ende Verzögerung. Ein grundlegender Unterschied zur Punkt-zu-Punkt Verbindung zwischen genau zwei miteinander kommunizierenden Sender- und Empfängerstationen liegt in der Übermittlung der Information über erfolgreichen oder nicht erfolgreichen Paketempfang auf Seite der Empfänger. Da die zu übertragende Information am Sender vorliegt, die Information über den Erfolg der Übertragung jedoch ausschließlich beim jeweiligen Empfänger, muss eine Erfolgsmeldung auf dem Rückweg von Empfänger zu Sender erfolgen. Diese Information wird dann zum Beispiel zur einfachen Paketwiederholung im nicht erfolgreichen Fall genutzt, oder aber um die Übertragungsrate an die Kapazität des Kanals anzupassen, oder beides. Grundsätzlich beschäftigt sich diese Arbeit mit der einmaligen, gleichzeitigen Übertragung von Information (einschließlich Wiederholungen) an mehrere Empfänger, wobei ein Vergleich zu an mehrere Empfänger sequentiell redundant übertragenden Systemen (Simulcast MIMO) angestellt wird. In dieser Arbeit ist die Betrachtung bezüglich eines Rückkanals auf Zeitduplexsysteme beschränkt. In diesen Systemen wird der Kanal für Hin- und Rückweg zeitlich orthogonalisiert. Damit steht für die Übermittlung der Erfolgsmeldung eine beschränkte Zeitdauer zur Verfügung. Je mehr an Kanalzugriffszeit für die Erfolgsmeldungen der potentiell vielen Empfänger verbraucht wird, desto geringer wird die Restzeit, in der dann entsprechend weniger audio-visuelle Nutzdaten übertragbar sind, was sich direkt auf die Dienstqualität auswirkt. Ein in der Literatur weniger ausführlich betrachteter Ansatz ist die gleichzeitige Übertragung von Rückmeldungen mehrerer Teilnehmer auf gleicher Frequenz und bei identischer Bandbreite, sowie unter Nutzung gleichartiger Signale (hier: orthogonale Frequenzmultiplexsignalformung). Das Schema wird in dieser Arbeit daher als zeitliche Aggregation von Rückmeldungen, engl. feedback aggregation, bezeichnet. Dabei wird, unabhängig von der Anzahl der Empfänger, eine konstante Zeitdauer für Rückmeldungen genutzt, womit auch der Datendurchsatz durch zusätzliche Empfänger nicht notwendigerweise sinkt. Diese Eigenschaft ist aus statisch konfigurierten und für einen einzigen Zweck konzipierten Systemen, wie z. B. der terrestrischen Fernsehübertragung, bekannt. In dieser Arbeit werden im Gegensatz dazu jedoch am Beispiel von WLAN Mehrzweck- und Mehrbenutzersysteme betrachtet. Es handelt sich in derartigen Systemen zur digitalen Datenübertragung dabei um einen entscheidenden Vorteil, unabhängig von der Empfängeranzahl zu bleiben, da es sonst unweigerlich zu Einschränkungen in der Güte der angebotenen Dienstleistung der allgegenwärtigen digitalen Vernetzung kommen muss. Vorliegende Arbeit zeigt in diesem Zusammenhang auf, welche Datenraten unter Benutzung von feedback aggregation in der Verteilung an mehrere Empfänger und in verschiedenen Szenarien zu erreichen sind. Hierbei zeigt sich, dass das Schema im Zusammenspiel mit einer Adaption der Datenrate an den Übertragungskanal inhärent einen Datenratengewinn durch Mehrbenutzerempfang zu erzielen vermag, wenn ein überlagerter idealer Paketauslöschungsschutz-Code angenommen wird. Des weiteren wird bei der Übertragung mit zeitlich begrenzter Ausführungsdauer, z. B. dem sogenannten Live-Fernsehen, aufgezeigt, wie sich die erreichbare Datenrate reduziert und welche Restfehlertoleranz an die Übertragung gestellt werden muss. Hierbei wird ebenso aufgezeigt, wie sich durch Verbesserung der Ratenadaption erstere erhöhen und zweitere verringern lässt. An einem auf handelsüblichen Computer-Systemen realisiertem Prototypen zur Live-Fernsehübertragung können die hierin beschriebenen Mechanismen zu großen Teilen gezeigt werden

Satellite Networks: Architectures, Applications, and Technologies

Since global satellite networks are moving to the forefront in enhancing the national and global information infrastructures due to communication satellites' unique networking characteristics, a workshop was organized to assess the progress made to date and chart the future. This workshop provided the forum to assess the current state-of-the-art, identify key issues, and highlight the emerging trends in the next-generation architectures, data protocol development, communication interoperability, and applications. Presentations on overview, state-of-the-art in research, development, deployment and applications and future trends on satellite networks are assembled

무선랜 비디오 멀티캐스트의 문제 발견 및 성능 향상 기법

학위논문 (박사)-- 서울대학교 대학원 공과대학 전기·컴퓨터공학부, 2017. 8. 최성현.Video multicast, streaming real-time videos via multicast, over wireless local area network (WLAN) has been considered a promising solution to share common venue-specific videos. By virtue of the nature of the wireless broadcast medium, video multicast basically enables scale-free video delivery, i.e., it can deliver a common video with the fixed amount of wireless resource regardless of the number of receivers. However, video multicast has not been widely enjoyed in our lives due to three major challenges: (1) power saving-related problem, (2) low reliability and efficiency, and (3) limited coverage. In this dissertation, we consider three research topics, i.e., (1) identification of practical issues with multicast power saving, (2) physical (PHY) rate and forward erasure correction code (FEC) rate adaptation over a single-hop network, and (3) multi-hop multicast, which deal with the three major challenges, respectively. Firstly, video multicast needs to be reliably delivered to power-saving stations, given that many portable devices are battery-powered. Accordingly, we investigate the impact of multicast power saving, and address two practical issues related with the multicast power saving. From the measurement with several commercial WLAN devices, we observe that many devices are not standard compliant, thus making video multicast performance severely degraded. We categorize such standard incompliant malfunctions that can result in significant packet losses. We also figure out a coexistence problem between video multicast and voice over Internet protocol (VoIP) when video receivers runs in power saving mode (PSM). The standard-compliant power save delivery of multicast deteriorates the VoIP performance in the same WLAN. We analyze the VoIP packet losses due to the coexistence problem, and propose a new power save delivery scheme to resolve the problem. We further implement the proposed scheme with an open source device driver, and our measurement results demonstrate that the proposed scheme significantly enhances the VoIP performance without sacrificing the video multicast performance. Second, multi-PHY rate FEC-applied wireless multicast enables reliable and efficient video multicast with intelligent selection of PHY rate and FEC rate. The optimal PHY/FEC rates depend on the cause of the packet losses. However, previous approaches select the PHY/FEC rates by considering only channel errors even when interference is also a major source of packet losses.We propose InFRA, an interference-aware PHY/FEC rate adaptation framework that (1) infers the cause of the packet losses based on received signal strength indicator (RSSI) and cyclic redundancy check (CRC) error notifications, and (2) determines the PHY/FEC rates based on the cause of packet losses. Our prototype implementation with off-the-shelf chipsets demonstrates that InFRA enhances the multicast delivery under various network scenarios. InFRA enables 2.3x and 1.8x more nodes to achieve a target video packet loss rate with a contention interferer and a hidden interferer, respectively, compared with the state-of-theart PHY/FEC rate adaptation scheme. To the best of our knowledge, InFRA is the first work to take the impact of interference into account for the PHY/FEC rate adaptation. Finally, collaborative relaying that enables selected receiver nodes to relay the received packets from source node to other nodes enhances service coverage, reliability, and efficiency of video multicast. The intelligent selection of sender nodes (source and relays) and their transmission parameters (PHY rate and the number of packets to send) is the key to optimize the performance. We propose EV-CAST, an interference and energy-aware video multicast system using collaborative relays, which entails online network management based on interference-aware link characterization, an algorithm for joint determination of sender nodes and transmission parameters, and polling-based relay protocol. In order to select most appropriate set of the relay nodes, EV-CAST considers interference, battery status, and spatial reuse, as well as other factors accumulated over last decades. Our prototype-based measurement results demonstrate that EV-CAST outperforms the state-of-the-art video multicast schemes. In summary, from Chapter 2 to Chapter 4, the aforementioned three pieces of the research work, i.e., identification of power saving-related practical issues, InFRA for interference-resilient single-hop multicast, and EV-CAST for efficient multi-hop multicast, will be presented, respectively.1 Introduction 1 1.1 Video Multicast over WLAN 1 1.2 Overview of Existing Approaches 4 1.2.1 Multicast Power Saving 4 1.2.2 Reliability and Efficiency Enhancement 4 1.2.3 Coverage Extension 5 1.3 Main Contributions 7 1.3.1 Practical Issues with Multicast Power Saving 7 1.3.2 Interference-aware PHY/FEC Rate Adaptation 8 1.3.3 Energy-aware Multi-hop Multicast 9 1.4 Organization of the Dissertation 10 2 Practical Issues with Multicast Power Saving 12 2.1 Introduction 12 2.2 Multicast & Power Management Operation in IEEE 802.11 14 2.3 Inter-operability Issue 15 2.3.1 Malfunctions of Commercial WLAN Devices 17 2.3.2 Performance Evaluation 20 2.4 Coexistence Problem of Video Multicast and VoIP 21 2.4.1 Problem Statement 21 2.4.2 Problem Identification: A Measurement Study 23 2.4.3 Packet Loss Analysis 27 2.4.4 Proposed Scheme 32 2.4.5 Performance Evaluation 33 2.5 Summary 37 3 InFRA: Interference-Aware PHY/FEC Rate Adaptation for Video Multicast over WLAN 39 3.1 Introduction 39 3.2 Related Work 42 3.2.1 Reliable Multicast Protocol 42 3.2.2 PHY/FEC rate adaptation for multicast service 44 3.2.3 Wireless Video Transmission 45 3.2.4 Wireless Loss Differentiation 46 3.3 Impact of Interference on Multi-rate FEC-applied Multicast 46 3.3.1 Measurement Setup 47 3.3.2 Measurement Results 47 3.4 InFRA: Interference-aware PHY/FEC Rate Adaptation Framework 49 3.4.1 Network Model and Objective 49 3.4.2 Overall Architecture 50 3.4.3 FEC Scheme 52 3.4.4 STA-side Operation 53 3.4.5 AP-side Operation 61 3.4.6 Practical Issues 62 3.5 Performance Evaluation 65 3.5.1 Measurement Setup 66 3.5.2 Small Scale Evaluation 67 3.5.3 Large Scale Evaluation 70 3.6 Summary 74 4 EV-CAST: Interference and Energy-aware Video Multicast Exploiting Collaborative Relays 75 4.1 Introduction 75 4.2 Factors for Sender Node and Transmission Parameter Selection 78 4.3 EV-CAST: Interference and Energy-aware Multicast Exploiting Collaborative Relays 80 4.3.1 Network Model and Objective 80 4.3.2 Overview 81 4.3.3 Network Management 81 4.3.4 Interference and Energy-aware Sender Nodes and Transmission Parameter Selection (INFER) Algorithm 87 4.3.5 Assignment, Polling, and Re-selection of Relays 93 4.3.6 Discussion 95 4.4 Evaluation 96 4.4.1 Measurement Setup 96 4.4.2 Micro-benchmark 98 4.4.3 Macro-benchmark 103 4.5 Related Work 105 4.5.1 Multicast Opportunistic Routing 105 4.5.2 Multicast over WLAN 106 4.6 Summary 106 5 Conclusion 108 5.1 Research Contributions 108 5.2 Future Research Directions 109 Abstract (In Korean) 121Docto

Secure and Privacy-Preserving Data Aggregation Protocols for Wireless Sensor Networks

This chapter discusses the need of security and privacy protection mechanisms in aggregation protocols used in wireless sensor networks (WSN). It presents a comprehensive state of the art discussion on the various privacy protection mechanisms used in WSNs and particularly focuses on the CPDA protocols proposed by He et al. (INFOCOM 2007). It identifies a security vulnerability in the CPDA protocol and proposes a mechanism to plug that vulnerability. To demonstrate the need of security in aggregation process, the chapter further presents various threats in WSN aggregation mechanisms. A large number of existing protocols for secure aggregation in WSN are discussed briefly and a protocol is proposed for secure aggregation which can detect false data injected by malicious nodes in a WSN. The performance of the protocol is also presented. The chapter concludes while highlighting some future directions of research in secure data aggregation in WSNs.Comment: 32 pages, 7 figures, 3 table

QoS framework for video streaming in home networks

In this thesis we present a new SNR scalable video coding scheme. An important advantage of the proposed scheme is that it requires just a standard video decoder for processing each layer. The quality of the delivered video depends on the allocation of bit rates to the base and enhancement layers. For a given total bit rate, the combination with a bigger base layer delivers higher quality. The absence of dependencies between frames in enhancement layers makes the system resilient to losses of arbitrary frames from an enhancement layer. Furthermore, that property can be used in a more controlled fashion. An important characteristic of any video streaming scheme is the ability to handle network bandwidth fluctuations. We made a streaming technique that observes the network conditions and based on the observations reconfigures the layer configuration in order to achieve the best possible quality. A change of the network conditions forces a change in the number of layers or the bit rate of these layers. Knowledge of the network conditions allows delivery of a video of higher quality by choosing an optimal layer configuration. When the network degrades, the amount of data transmitted per second is decreased by skipping frames from an enhancement layer on the sender side. The presented video coding scheme allows skipping any frame from an enhancement layer, thus enabling an efficient real-time control over transmission at the network level and fine-grained control over the decoding of video data. The methodology proposed is not MPEG-2 specific and can be applied to other coding standards. We made a terminal resource manager that enables trade-offs between quality and resource consumption due to the use of scalable video coding in combination with scalable video algorithms. The controller developed for the decoding process optimizes the perceived quality with respect to the CPU power available and the amount of input data. The controller does not depend on the type of scalability technique and can therefore be used with any scalable video. The controller uses the strategy that is created offline by means of a Markov Decision Process. During the evaluation it was found that the correctness of the controller behavior depends on the correctness of parameter settings for MDP, so user tests should be employed to find the optimal settings

Routing and video streaming in drone networks

PhDDrones can be used for several civil applications including search and rescue, coverage, and aerial imaging. Newer applications like construction and delivery of goods are also emerging. Performing tasks as a team of drones is often beneficial but requires coordination through communication. In this thesis, the communication requirements of video streaming drone applications based on existing works are studied. The existing communication technologies are then analyzed to understand if the communication requirements posed by these drone applications can be met by the available technologies. The shortcomings of existing technologies with respect to drone applications are identified and potential requirements for future technologies are suggested. The existing communication and routing protocols including ad-hoc on-demand distance vector (AODV), location-aided routing (LAR), and greedy perimeter stateless routing (GPSR) protocols are studied to identify their limitations in context to the drone networks. An application scenario where a team of drones covers multiple areas of interest is considered, where the drones follow known trajectories and transmit continuous streams of sensed traffic (images or video) to a ground station. A route switching (RS) algorithm is proposed that utilizes both the location and the trajectory information of the drones to schedule and update routes to overcome route discovery and route error overhead. Simulation results show that the RS scheme outperforms LAR and AODV by achieving higher network performance in terms of throughput and delay. Video streaming drone applications such as search and rescue, surveillance, and disaster management, benefit from multicast wireless video streaming to transmit identical data to multiple users. Video multicast streaming using IEEE 802.11 poses challenges of reliability, performance, and fairness under tight delay bounds. Because of the mobility of the video sources and the high data-rate of the videos, the transmission rate should be adapted based on receivers' link conditions. Rate-adaptive video multicast streaming in IEEE 802.11 requires wireless link estimation as well as frequent feedback from multiple receivers. A contribution to this thesis is an application-layer rate-adaptive video multicast streaming framework using an 802.11 ad-hoc network that is applicable when both the sender and the receiver nodes are mobile. The receiver nodes of a multicast group are assigned with roles dynamically based on their link conditions. An application layer video multicast gateway (ALVM-GW) adapts the transmission rate and the video encoding rate based on the received feedback. Role switching between multiple receiver nodes (designated nodes) cater for mobility and rate adaptation addresses the challenges of performance and fairness. The reliability challenge is addressed through re-transmission of lost packets while delays under given bounds are achieved through video encoding rate adaptation. Emulation and experimental results show that the proposed approach outperforms legacy multicast in terms of packet loss and video quality

Integration of unidirectional technologies into wireless back-haul architecture

This thesis was submitted for the degree of Docter of Philosophy and awarded by Brunel University.Back-haul infrastructures of today's wireless operators must support the triple-play services demanded by the market or regulatory bodies. To cope with increasing capacity demand, the EU FP7 project CARMEN has developed a cost-effective heterogeneous multi-radio wireless back-haul architecture, which may also leverage the native multicast capabilities of broadcast technologies such as DVB-T to off-load high-bandwidth broadcast content delivery. However, the integration of such unidirectional technologies into a packet-switched architecture requires careful considerations. The contribution of this thesis is the investigation, design and evaluation of protocols and mechanisms facilitating the integration of such unidirectional technologies into the wireless back-haul architecture so that they can be configured and utilized by the spectrum and capacity optimization modules. This integration mainly concerns the control plane and, in particular, the aspects related to resource and capability descriptions, neighborhood, link and Multi Protocol Label Switching (MPLS) Label-Switched Path (LSP) monitoring, unicast and multicast LSP signalling as well as topology forming and maintenance. During the course of this study we have analyzed the problem space, proposed solutions to the resulting research questions and evaluated our approach. Our results show that the now Unidirectional Technology (UDT)-aware architecture can readily consider Unidirectional Technologies (UDTs) to distribute, for example, broadcast content