Index to 1981 NASA Tech Briefs, volume 6, numbers 1-4

Short announcements of new technology derived from the R&D activities of NASA are presented. These briefs emphasize information considered likely to be transferrable across industrial, regional, or disciplinary lines and are issued to encourage commercial application. This index for 1981 Tech Briefs contains abstracts and four indexes: subject, personal author, originating center, and Tech Brief Number. The following areas are covered: electronic components and circuits, electronic systems, physical sciences, materials, life sciences, mechanics, machinery, fabrication technology, and mathematics and information sciences

In-line quality control for Zero Defect Manufacturing: design, development and uncertainty analysis of vision-based instruments for dimensional measurements at different scales

Lo scopo di questo progetto di dottorato industriale finanziato attraverso una borsa di studio della Regione Marche è stato quello di sviluppare ricerca con potenziale impatto su un settore industriale, promuovere il coinvolgimento delle fabbriche e delle imprese locali nella ricerca e innovazione svolta in collaborazione con l'università e produrre ricerca in linea con le esigenze dell'ambiente industriale, non solo a livello regionale. Quindi, attraverso la collaborazione con una torneria locale (Zannini SpA) e una piccola azienda high-tech focalizzata sull'introduzione dell'innovazione meccatronica nel settore della tornitura (Z4Tec srl), e anche grazie a una collaborazione internazionale con l'Università di Anversa, abbiamo progettato e sviluppato nuovi strumenti per il controllo qualità in linea, basati su tecnologie senza contatto, in particolare tecnologie elettro-ottiche. Portando anche l'attenzione sull'importanza di prendere in considerazione l'incertezza, poiché è fondamentale nel processo decisionale basato sui dati che sono alla base di una strategia di Zero Defect Manufacturing. Infatti, la scarsa qualità delle misure può pregiudicare la qualità dei dati. In particolare, questo lavoro presenta due strumenti di misura che sono stati progettati e sviluppati con lo scopo di effettuare controllo qualità in linea di produzione e l’incertezza di misura di ogni strumento è stata analizzata in confronto ad altri strumenti presenti sul mercato. Nella parte finale di questo lavoro si è valutata l’incertezza di un profilometro a triangolazione di linea laser. Pertanto, la ricerca condotta in questa tesi può essere organizzata in due obiettivi principali: lo sviluppo di nuovi sistemi di misura dimensionale basati sulla visione da implementare in linea di produzione e l'analisi dell'incertezza di questi strumenti di misura. Per il primo obiettivo ci siamo concentrati su due tipi di misure dimensionali imposte dall'industria manifatturiera: macroscopiche (misure in mm) e microscopiche (misure in µm). Per le misure macroscopiche l'obiettivo era il controllo in linea della qualità dimensionale di pezzi torniti attraverso la profilometria ottica telecentrica. Il campione da ispezionare è stato posto tra l'illuminatore e l'obiettivo per ottenere la proiezione dell'ombra del campione. Le misure sono state eseguite mediante analisi grafica dell'immagine. Abbiamo discusso le disposizioni meccaniche mirate a ottimizzare le immagini acquisite e i problemi che eventuali disallineamenti meccanici dei componenti potrebbero introdurre nella qualità delle immagini. Per le misure microscopiche abbiamo progettato un sistema di misurazione della rugosità superficiale basato sulla visione retroilluminata, con l'obiettivo di determinare le condizioni ottimali di imaging utilizzando la modulation transfer function e l'uso di una electrically tunable lens. Un campione tornito (un cilindro) è posto di fronte a una telecamera ed è retroilluminato da una sorgente di luce collimata; tale configurazione ottica fornisce l'immagine del bordo del campione. Per testare la sensibilità del sistema di misura è stata utilizzata una serie di campioni di acciaio torniti con diverse rugosità superficiali. Per il secondo obiettivo, le tecniche di valutazione dell'incertezza di misura utilizzate in questo lavoro sono state un'analisi dell'incertezza statistica di tipo A e un'analisi Gage R&R. Nel caso del profilometro telecentrico, l'analisi è stata eseguita in confronto con altri dispositivi presenti sul mercato con un'analisi di tipo A e una Gage R&R. L'incertezza di misura del profilometro si è rivelata sufficiente per ottenere risultati nell'intervallo di tolleranza richiesto. Per il sistema di visione retroilluminato, il confronto dei risultati è stato effettuato con altri strumenti allo stato dell'arte, con un'analisi di Tipo A. Il confronto ha mostrato che le prestazioni dello strumento retroilluminato dipendono dai valori di rugosità superficiale considerati; mentre a valori maggiori di rugosità l'offset aumenta, per valori inferiori di rugosità i risultati sono compatibili con quelli dello strumento di riferimento (a stilo). Infine, sono state valutate la ripetibilità e la riproducibilità di un profilometro a triangolazione di linea laser, attraverso uno studio Gage R&R. Ogni punto di misura è stato ispezionato da tre operatori e l'insieme dei dati è stato elaborato con un'analisi dell'incertezza di Tipo A. Successivamente, uno studio Gage R&R ha contribuito a indagare la ripetibilità, la riproducibilità e la variabilità del sistema. Questa analisi ha dimostrato un'incertezza accettabile.The purpose of this industrial PhD project financed through a scholarship from the Regione Marche was to develop research with potential impact on an industrial sector, to promote the involvement of local factories and companies in research and innovation performed jointly with the university and to produce research in line with the needs of the industrial environment, not only at regional level. Hence, through collaborating with a local turning factory (Zannini SpA) and a small high-tech company focused on introducing mechatronic innovation in the turning sector (Z4Tec srl), and also thanks to an international collaboration with the University of Antwerp, we designed and developed new instruments for in-line quality control, based on non-contact technologies, specifically electro-optical technologies. While also bringing attention to the importance of taking uncertainty into consideration, since it is pivotal in data-based decision making which are at the base of a Zero Defect Manufacturing strategy. This means that poor quality of measurements can prejudice the quality of the data. In particular, this work presents two measurement instruments that were designed and developed for the purpose of in-line quality control and the uncertainty of each of the two instruments was evaluated and analyzed in comparison with instruments already present on the market. In the last part of this work, the uncertainty of a hand-held laser-line triangulation profilometer is estimated. Hence, the research conducted in this thesis can be organized in two main objectives: the development of new vision-based dimensional measurement systems to be implemented in production line and the uncertainty analysis of these measurement instruments. For the first objective we focused on two types of dimensional measurements imposed by the manufacturing industry: macroscopic (measuring dimensions in mm) and microscopic (measuring roughness in µm). For macroscopic measurements the target was the in-production dimensional quality control of turned parts through telecentric optical profilometry. The sample to be inspected was placed between illuminator and objective in order to obtain the projection of the shadow of the sample over a white background. Dimensional measurements were then performed by means of image processing over the image obtained. We discussed the mechanical arrangements targeted to optimize images acquired as well as the main issues that eventual mechanical misalignments of components might introduce in the quality of images. For microscopic measurements we designed a backlit vision-based surface roughness measurement system with a focus on smart behaviors such as determining the optimal imaging conditions using the modulation transfer function and the use of an electrically tunable lens. A turned sample (a cylinder) is placed in front of a camera and it is backlit by a collimated source of light; such optical configuration provides the image of the edge of the sample. A set of turned steel samples with different surface roughness was used to test the sensitivity of the measurement system. For the second objective, the measurement uncertainty evaluation techniques used in this work were a Type A statistical uncertainty analysis and a Gage R&R analysis. In the case of the telecentric profilometer, the analysis was performed in comparison with other on-the-market devices with a Type A analysis and a Gage R&R analysis. The measurement uncertainty of the profilometer proved to be sufficient to obtain results within the tolerance interval required. For the backlit vision system, the comparison of the results was made with other state-of-the-art instruments, with a Type A analysis. The comparison showed that the performance of the backlit instrument depends on the values of surface roughness considered; while at larger values of roughness the offset increases, the results are compatible with the ones of the reference instrument (stylus-based) at lower values of roughness. Lastly, the repeatability and reproducibility of a laser-line triangulation profilometer were assessed, through a Gage R&R study. Each measuring point was inspected by three different operators and the data set has been, at first, processed by a Type A uncertainty analysis. Then, a Gage R&R study helped investigate repeatability, reproducibility and the system variability. This analysis showed that the presented laser-line triangulation system has an acceptable uncertainty

Training of Crisis Mappers and Map Production from Multi-sensor Data: Vernazza Case Study (Cinque Terre National Park, Italy)

This aim of paper is to presents the development of a multidisciplinary project carried out by the cooperation between Politecnico di Torino and ITHACA (Information Technology for Humanitarian Assistance, Cooperation and Action). The goal of the project was the training in geospatial data acquiring and processing for students attending Architecture and Engineering Courses, in order to start up a team of "volunteer mappers". Indeed, the project is aimed to document the environmental and built heritage subject to disaster; the purpose is to improve the capabilities of the actors involved in the activities connected in geospatial data collection, integration and sharing. The proposed area for testing the training activities is the Cinque Terre National Park, registered in the World Heritage List since 1997. The area was affected by flood on the 25th of October 2011. According to other international experiences, the group is expected to be active after emergencies in order to upgrade maps, using data acquired by typical geomatic methods and techniques such as terrestrial and aerial Lidar, close-range and aerial photogrammetry, topographic and GNSS instruments etc.; or by non conventional systems and instruments such us UAV, mobile mapping etc. The ultimate goal is to implement a WebGIS platform to share all the data collected with local authorities and the Civil Protectio

An inspection technology of inner surface of the fine hole based on machine vision

Fine holes are an important structural component of industrial components, and their inner surface quality is closely related to their function.In order to detect the quality of the inner surface of the fine hole,a special optical measurement system was investigated in this paper. A sight pipe is employed to guide the external illumination light into the fine hole and output the relevant images simultaneously. A flexible light array is introduced to suit the narrow space, and the effective field of view is analyzed. Besides, the arc surface projection error and manufacturing assembly error of the device are analyzed, then compensated or ignored if small enough. In the test of prefabricated circular defects with the diameter {\phi}0.1mm, {\phi}0.2mm, 0.4mm distance distribution and the fissure defects with the width 0.3mm, the maximum measurement error standard deviation are all about 10{\mu}m. The minimum diameter of the measured fine hole is 4mm and the depth can reach 47mm

Thermal Modeling and Imaging of As-built Automotive Parts

Simulation is of significant importance in the automotive industry and can be done for various applications ranging from fluid flow analysis to complex thermal management of components. This thesis describes the method and necessary requirements for thermal modeling of automotive parts. Simulation of under hood and under vehicle automotive poses several challenges, the shape and complexity of the geometry used being the first and foremost to be considered. This thesis addresses the simulation of thermal images of as-built automotive parts using the 3D meshes generated from 3D modeling tools, CAD meshes and reverse engineered meshes. Thermal modeling requires complete knowledge about the under hood and under vehicle automotive components. Many factors, both inside and outside the vehicle, affect the heat flow pattern of the vehicle under consideration. Thermal image sequences of under vehicle chassis were acquired to understand the thermal heat pattern and to serve as a basis for simulation. It was inferred that the exhaust system is the system with significant change in temperature and is at temperature close to 450 degree Celsius when the engine is operating at its full capacity. The exhaust system components, namely the catalytic converter, muffler and the exhaust pipes, were considered as the significant components for thermal modeling. The temperature curves of those components were measured with the help of an infrared thermometer to enhance the results of simulation. Application of thermal imaging in the field of threat detection is also addressed in this thesis. Simulation or thermal modeling of the automotive components was done using the software MuSES. The thermal properties and the boundary conditions were assigned to the 3D geometry used and the transient solution was carried out over a period of time. The results for the three types of meshes mentioned earlier are presented and the thermal predictions are analyzed. As-built models can be modeled as they are with the help of reverse engineering, and the temperature predictions of those components provide better simulation results close to reality. The thesis also addresses the idea of comparison between simulation results and real time experimental results

Proceeding Of Mechanical Engineering Research Day 2016 (MERD’16)

This Open Access e-Proceeding contains a compilation of 105 selected papers from the Mechanical Engineering Research Day 2016 (MERD’16) event, which is held in Kampus Teknologi, Universiti Teknikal Malaysia Melaka (UTeM) - Melaka, Malaysia, on 31 March 2016. The theme chosen for this event is ‘IDEA. INSPIRE. INNOVATE’. It was gratifying to all of us when the response for MERD’16 is overwhelming as the technical committees received more than 200 submissions from various areas of mechanical engineering. After a peer-review process, the editors have accepted 105 papers for the e-proceeding that cover 7 main themes. This open access e-Proceeding can be viewed or downloaded at www3.utem.edu.my/care/proceedings. We hope that these proceeding will serve as a valuable reference for researchers. With the large number of submissions from the researchers in other faculties, the event has achieved its main objective which is to bring together educators, researchers and practitioners to share their findings and perhaps sustaining the research culture in the university. The topics of MERD’16 are based on a combination of fundamental researches, advanced research methodologies and application technologies. As the editor-in-chief, we would like to express our gratitude to the editorial board and fellow review members for their tireless effort in compiling and reviewing the selected papers for this proceeding. We would also like to extend our great appreciation to the members of the Publication Committee and Secretariat for their excellent cooperation in preparing the proceeding of MERD’16