67 research outputs found
Robust acoustic signal detection and synchronization in a time varying ocean environment
Submitted in partial fulfillment of the requirements for the degree of Master of Science at the Massachusetts Institute of Technology and the Woods Hole Oceanographic Institution September 2012Signal detection and synchronization in the time varying ocean environment is a difficult endeavor. The current common methods include using a linear frequency modulated chirped pulse or maximal length sequence as a detection pulse, then match filtering to that signal. In higher signal to noise ratio (SNR) environments (~0 dB
and higher) this has been a suitable solution. As the SNR drops lower however, this
solution no longer provides an acceptable probability of detection for a given tolerable
probability of false alarm. The issue derives from the inherent coherence issues in
the ocean environment which limit the useful matched filter length. This thesis proposes
an alternative method of detection based on a recursive least squares linearly
adaptive equalizer which we term the Adaptive Linear Equalizer Detector (ALED).
This detectors performance has demonstrated reliable probability of detection with
minimal interfering false alarms with SNR as low as -20 dB. Additionally this thesis
puts forth a computationally feasible method for implementing the detector.Support from the Office of Naval
Research (through ONR grant #N00014-07-10738 and #N00014-11-10426)
Underwater Sensor Nodes and Networks
Sensor technology has matured enough to be used in any type of environment. The appearance of new physical sensors has increased the range of environmental parameters for gathering data. Because of the huge amount of unexploited resources in the ocean environment, there is a need of new research in the field of sensors and sensor networks. This special issue is focused on collecting recent advances on underwater sensors and underwater sensor networks in order to measure, monitor, surveillance of and control of underwater environments. On the one hand, from the sensor node perspective, we will see works related with the deployment of physical sensors, development of sensor nodes and transceivers for sensor nodes, sensor measurement analysis and several issues such as layer 1 and 2 protocols for underwater communication and sensor localization and positioning systems. On the other hand, from the sensor network perspective, we will see several architectures and protocols for underwater environments and analysis concerning sensor network measurements. Both sides will provide us a complete view of last scientific advances in this research field.Lloret, J. (2013). Underwater Sensor Nodes and Networks. Sensors. 13(9):11782-11796. doi:10.3390/s130911782S1178211796139Garcia, M., Sendra, S., Lloret, G., & Lloret, J. (2011). Monitoring and control sensor system for fish feeding in marine fish farms. IET Communications, 5(12), 1682-1690. doi:10.1049/iet-com.2010.0654Martinez, J. J., Myers, J. R., Carlson, T. J., Deng, Z. D., Rohrer, J. S., Caviggia, K. A., … Weiland, M. A. (2011). Design and Implementation of an Underwater Sound Recording Device. Sensors, 11(9), 8519-8535. doi:10.3390/s110908519Ardid, M., MartÃnez-Mora, J. A., Bou-Cabo, M., Larosa, G., Adrián-MartÃnez, S., & Llorens, C. D. (2012). Acoustic Transmitters for Underwater Neutrino Telescopes. Sensors, 12(4), 4113-4132. doi:10.3390/s120404113Baronti, F., Fantechi, G., Roncella, R., & Saletti, R. (2012). Wireless Sensor Node for Surface Seawater Density Measurements. Sensors, 12(3), 2954-2968. doi:10.3390/s120302954Mà nuel, A., Roset, X., Rio, J. D., Toma, D. M., Carreras, N., Panahi, S. S., … Cadena, J. (2012). Ocean Bottom Seismometer: Design and Test of a Measurement System for Marine Seismology. Sensors, 12(3), 3693-3719. doi:10.3390/s120303693Jollymore, A., Johnson, M. S., & Hawthorne, I. (2012). Submersible UV-Vis Spectroscopy for Quantifying Streamwater Organic Carbon Dynamics: Implementation and Challenges before and after Forest Harvest in a Headwater Stream. Sensors, 12(4), 3798-3813. doi:10.3390/s120403798Won, T.-H., & Park, S.-J. (2012). Design and Implementation of an Omni-Directional Underwater Acoustic Micro-Modem Based on a Low-Power Micro-Controller Unit. Sensors, 12(2), 2309-2323. doi:10.3390/s120202309Sánchez, A., Blanc, S., Yuste, P., Perles, A., & Serrano, J. J. (2012). An Ultra-Low Power and Flexible Acoustic Modem Design to Develop Energy-Efficient Underwater Sensor Networks. Sensors, 12(6), 6837-6856. doi:10.3390/s120606837Shin, S.-Y., & Park, S.-H. (2011). A Cost Effective Block Framing Scheme for Underwater Communication. Sensors, 11(12), 11717-11735. doi:10.3390/s111211717Kim, Y., & Park, S.-H. (2011). A Query Result Merging Scheme for Providing Energy Efficiency in Underwater Sensor Networks. Sensors, 11(12), 11833-11855. doi:10.3390/s111211833Llor, J., & Malumbres, M. P. (2012). Underwater Wireless Sensor Networks: How Do Acoustic Propagation Models Impact the Performance of Higher-Level Protocols? Sensors, 12(2), 1312-1335. doi:10.3390/s120201312Zhang, G., Hovem, J. M., & Dong, H. (2012). Experimental Assessment of Different Receiver Structures for Underwater Acoustic Communications over Multipath Channels. Sensors, 12(2), 2118-2135. doi:10.3390/s120202118Ramezani, H., & Leus, G. (2012). Ranging in an Underwater Medium with Multiple Isogradient Sound Speed Profile Layers. Sensors, 12(3), 2996-3017. doi:10.3390/s120302996Lloret, J., Sendra, S., Ardid, M., & Rodrigues, J. J. P. C. (2012). Underwater Wireless Sensor Communications in the 2.4 GHz ISM Frequency Band. Sensors, 12(4), 4237-4264. doi:10.3390/s120404237Gao, M., Foh, C. H., & Cai, J. (2012). On the Selection of Transmission Range in Underwater Acoustic Sensor Networks. Sensors, 12(4), 4715-4729. doi:10.3390/s120404715Gómez, J. V., Sandnes, F. E., & Fernández, B. (2012). Sunlight Intensity Based Global Positioning System for Near-Surface Underwater Sensors. Sensors, 12(2), 1930-1949. doi:10.3390/s120201930Han, G., Jiang, J., Shu, L., Xu, Y., & Wang, F. (2012). Localization Algorithms of Underwater Wireless Sensor Networks: A Survey. Sensors, 12(2), 2026-2061. doi:10.3390/s120202026Moradi, M., Rezazadeh, J., & Ismail, A. S. (2012). A Reverse Localization Scheme for Underwater Acoustic Sensor Networks. Sensors, 12(4), 4352-4380. doi:10.3390/s120404352Lee, S., & Kim, K. (2012). Localization with a Mobile Beacon in Underwater Acoustic Sensor Networks. Sensors, 12(5), 5486-5501. doi:10.3390/s120505486Mohamed, N., Jawhar, I., Al-Jaroodi, J., & Zhang, L. (2011). Sensor Network Architectures for Monitoring Underwater Pipelines. Sensors, 11(11), 10738-10764. doi:10.3390/s111110738Macias, E., Suarez, A., Chiti, F., Sacco, A., & Fantacci, R. (2011). A Hierarchical Communication Architecture for Oceanic Surveillance Applications. Sensors, 11(12), 11343-11356. doi:10.3390/s111211343Zhang, S., Yu, J., Zhang, A., Yang, L., & Shu, Y. (2012). Marine Vehicle Sensor Network Architecture and Protocol Designs for Ocean Observation. Sensors, 12(1), 373-390. doi:10.3390/s120100373Climent, S., Capella, J. V., Meratnia, N., & Serrano, J. J. (2012). Underwater Sensor Networks: A New Energy Efficient and Robust Architecture. Sensors, 12(1), 704-731. doi:10.3390/s120100704Min, H., Cho, Y., & Heo, J. (2012). Enhancing the Reliability of Head Nodes in Underwater Sensor Networks. Sensors, 12(2), 1194-1210. doi:10.3390/s120201194Yoon, S., Azad, A. K., Oh, H., & Kim, S. (2012). AURP: An AUV-Aided Underwater Routing Protocol for Underwater Acoustic Sensor Networks. Sensors, 12(2), 1827-1845. doi:10.3390/s120201827Caiti, A., Calabrò, V., Dini, G., Lo Duca, A., & Munafò, A. (2012). Secure Cooperation of Autonomous Mobile Sensors Using an Underwater Acoustic Network. Sensors, 12(2), 1967-1989. doi:10.3390/s120201967Wu, H., Chen, M., & Guan, X. (2012). A Network Coding Based Routing Protocol for Underwater Sensor Networks. Sensors, 12(4), 4559-4577. doi:10.3390/s120404559Navarro, G., Huertas, I. E., Costas, E., Flecha, S., DÃez-Minguito, M., Caballero, I., … Ruiz, J. (2012). Use of a Real-Time Remote Monitoring Network (RTRM) to Characterize the Guadalquivir Estuary (Spain). Sensors, 12(2), 1398-1421. doi:10.3390/s120201398Baladrón, C., Aguiar, J. M., Calavia, L., Carro, B., Sánchez-Esguevillas, A., & Hernández, L. (2012). Performance Study of the Application of Artificial Neural Networks to the Completion and Prediction of Data Retrieved by Underwater Sensors. Sensors, 12(2), 1468-1481. doi:10.3390/s12020146
Development of an acoustic communication link for micro underwater vehicles
PhD ThesisIn recent years there has been an increasing trend towards the use of
Micro Remotely Operated Vehicles (μROVs), such as the Videoray and
Seabotix LBV products, for a range of subsea applications, including
environmental monitoring, harbour security, military surveillance and
offshore inspection. A major operational limitation is the umbilical cable,
which is traditionally used to supply power and communications to the
vehicle. This tether has often been found to significantly restrict the
agility of the vehicle or in extreme cases, result in entanglement with
subsea structures.
This thesis addresses the challenges associated with developing a reliable
full-duplex wireless communications link aimed at tetherless operation
of a μROV. Previous research has demonstrated the ability to
support highly compressed video transmissions over several kilometres
through shallow water channels with large range-depth ratios. However,
the physical constraints of these platforms paired with the system cost
requirements pose significant additional challenges.
Firstly, the physical size/weight of transducers for the LF (8-16kHz)
and MF (16-32kHz) bands would significantly affect the dynamics of the
vehicle measuring less than 0.5m long. Therefore, this thesis explores the
challenges associated with moving the operating frequency up to around
50kHz centre, along with the opportunities for increased data rate and
tracking due to higher bandwidth.
The typical operating radius of μROVs is less than 200m, in water
< 100m deep, which gives rise to multipath channels characterised by
long timespread and relatively sparse arrivals. Hence, the system must
be optimised for performance in these conditions. The hardware costs of
large multi-element receiver arrays are prohibitive when compared to the
cost of the μROV platform. Additionally, the physical size of such arrays
complicates deployment from small surface vessels. Although some
recent developments in iterative equalisation and decoding structures
have enhanced the performance of single element receivers, they are not
found to be adequate in such channels. This work explores the optimum
cost/performance trade-off in a combination of a micro beamforming array
using a Bit Interleaved Coded Modulation with Iterative Decoding
(BICM-ID) receiver structure.
The highly dynamic nature of μROVs, with rapid acceleration/deceleration
and complex thruster/wake effects, are also a significant challenge to reliable
continuous communications. The thesis also explores how these effects
can best be mitigated via advanced Doppler correction techniques,
and adaptive coding and modulation via a simultaneous frequency multiplexed
down link. In order to fully explore continuous adaptation of
the transmitted signals, a real-time full-duplex communication system
was constructed in hardware, utilising low cost components and a highly
optimised PC based receiver structure. Rigorous testing, both in laboratory
conditions and through extensive field trials, have enabled the
author to explore the performance of the communication link on a vehicle
carrying out typical operations and presenting a wide range of channel,
noise, Doppler and transmission latency conditions. This has led to a
comprehensive set of design recommendations for a reliable and cost effective
link capable of continuous throughputs of >30 kbits/s
Mobile node-aided localization and tracking in terrestrial and underwater networks
In large-scale wireless sensor networks (WSNs), the position information of individual
sensors is very important for many applications. Generally, there are a small number
of position-aware nodes, referred to as the anchors. Every other node can estimate its
distances to the surrounding anchors, and then employ trilateration or triangulation for
self-localization. Such a system is easy to implement, and thus popular for both terrestrial
and underwater applications, but it suffers from some major drawbacks. First, the density
of the anchors is generally very low due to economical considerations, leading to poor
localization accuracy. Secondly, the energy and bandwidth consumptions of such systems
are quite significant. Last but not the least, the scalability of a network based on fixed
anchors is not good. Therefore, whenever the network expands, more anchors should be
deployed to guarantee the required performance. Apart from these general challenges,
both terrestrial and underwater networks have their own specific ones. For example, realtime
channel parameters are generally required for localization in terrestrial WSNs. For
underwater networks, the clock skew between the target sensor and the anchors must
be considered. That is to say, time synchronization should be performed together with
localization, which makes the problem complicated.
An alternative approach is to employ mobile anchors to replace the fixed ones. For
terrestrial networks, commercial drones and unmanned aerial vehicles (UAVs) are very
good choices, while autonomous underwater vehicles (AUVs) can be used for underwater
applications. Mobile anchors can move along a predefined trajectory and broadcast beacon
signals. By listening to the messages, the other nodes in the network can localize themselves
passively. This architecture has three major advantages: first, energy and bandwidth consumptions can be significantly reduced; secondly, the localization accuracy can be much
improved with the increased number of virtual anchors, which can be boosted at negligible
cost; thirdly, the coverage can be easily extended, which makes the solution and the network
highly scalable.
Motivated by this idea, this thesis investigates the mobile node-aided localization and
tracking in large-scale WSNs. For both terrestrial and underwater WSNs, the system
design, modeling, and performance analyses will be presented for various applications,
including: (1) the drone-assisted localization in terrestrial networks; (2) the ToA-based
underwater localization and time synchronization; (3) the Doppler-based underwater localization;
(4) the underwater target detection and tracking based on the convolutional
neural network and the fractional Fourier transform. In these applications, different challenges
will present, and we will see how these challenges can be addressed by replacing
the fixed anchors with mobile ones. Detailed mathematical models will be presented, and
extensive simulation and experimental results will be provided to verify the theoretical
results. Also, we will investigate the channel estimation for the fifth generation (5G) wireless
communications. A pilot decontamination method will be presented for the massive
multiple-input-multiple-output communications, and the data-aided channel tracking will
be discussed for millimeter wave communications. We will see that the localization problem
is highly coupled with the channel estimation in wireless communications
Using ships of opportunity for passive ocean sensing
In recent years, there has been an increased interest in passive ocean sensing. Commercial shipping vessels are ubiquitous in many parts of the ocean and can serve as stand-in sources for ocean sensing experiments. The ray-based blind deconvolution (RBD) technique for ocean waveguides estimates both the unknown waveform radiated by some source of opportunity and the channel impulse response (CIR) between the source and the receiving elements of an array of hydrophones using only measured signals, knowledge of the array geometry, and the local sound speed. This research explores the use of the RBD estimator to generate a robust, source-independent, acoustic observable from measurements of ships of opportunity and the use this observable together with state-of-the-art signal processing tools in solving underwater acoustics inverse problems, such as source localization and tomography.Ph.D
- …