Four-element phased-array beamformers and a self-interference canceling full-duplex transciver in 130-nm SiGe for 5G applications at 26 GHz

This thesis is on the design of radio-frequency (RF) integrated front-end circuits for next generation 5G communication systems. The demand for higher data rates and lower latency in 5G networks can only be met using several new technologies including, but not limited to, mm-waves, massive-MIMO, and full-duplex. Use of mm-waves provides more bandwidth that is necessary for high data rates at the cost of increased attenuation in air. Massive-MIMO arrays are required to compensate for this increased path loss by providing beam steering and array gain. Furthermore, full duplex operation is desirable for improved spectrum efficiency and reduced latency. The difficulty of full duplex operation is the self-interference (SI) between transmit (TX) and receive (RX) paths. Conventional methods to suppress this interference utilize either bulky circulators, isolators, couplers or two separate antennas. These methods are not suitable for fully-integrated full-duplex massive-MIMO arrays. This thesis presents circuit and system level solutions to the issues summarized above, in the form of SiGe integrated circuits for 5G applications at 26 GHz. First, a full-duplex RF front-end architecture is proposed that is scalable to massive-MIMO arrays. It is based on blind, RF self-interference cancellation that is applicable to single/shared antenna front-ends. A high resolution RF vector modulator is developed, which is the key building block that empowers the full-duplex frontend architecture by achieving better than state-of-the-art 10-b monotonic phase control. This vector modulator is combined with linear-in-dB variable gain amplifiers and attenuators to realize a precision self-interference cancellation circuitry. Further, adaptive control of this SI canceler is made possible by including an on-chip low-power IQ downconverter. It correlates copies of transmitted and received signals and provides baseband/dc outputs that can be used to adaptively control the SI canceler. The solution comes at the cost of minimal additional circuitry, yet significantly eases linearity requirements of critical receiver blocks at RF/IF such as mixers and ADCs. Second, to complement the proposed full-duplex front-end architecture and to provide a more complete solution, high-performance beamformer ICs with 5-/6- b phase and 3-/4-b amplitude control capabilities are designed. Single-channel, separate transmitter and receiver beamformers are implemented targeting massive- MIMO mode of operation, and their four-channel versions are developed for phasedarray communication systems. Better than state-of-the-art noise performance is obtained in the RX beamformer channel, with a full-channel noise figure of 3.3 d

Wideband Watt-Level Spatial Power-Combined Power Amplifier in SiGe BiCMOS Technology for Efficient mm-Wave Array Transmitters

The continued demand for high-speed wireless communications is driving the development of integrated high-power transmitters at millimeter wave (mm-Wave) frequencies. Si-based technologies allow achieving a high level of integration but usually provide insufficient generated RF power to compensate for the increased propagation and material losses at mm-Wave bands due to the relatively low breakdown voltage of their devices. This problem can be reduced significantly if one could combine the power of multiple active devices on each antenna element. However, conventional on-chip power combining networks have inherently high insertion losses reducing transmitter efficiency and limiting its maximum achievable output power.This work presents a non-conventional design approach for mm-Wave Si-based Watt-level power amplifiers that is based on novel power-combining architecture, where an array of parallel custom PA-cells suited on the same chip is interfaced to a single substrate integrated waveguide (to be a part of an antenna element). This allows one to directly excite TEm0 waveguide modes with high power through spatial power combining functionality, obviating the need for intermediate and potentially lossy on-chip power combiners. The proposed solution offers wide impedance bandwidth (50%) and low insertion losses (0.4 dB), which are virtually independent from the number of interfaced PA-cells. The work evaluates the scalability bounds of the architecture as well as discusses the critical effects of coupled non-identical PA-cells, which are efficiently reduced by employing on-chip isolation load resistors.The proposed architecture has been demonstrated through an example of the combined PA with four differential cascode PA-cells suited on the same chip, which is flip-chip interconnected to the combiner placed on a laminate. This design is implemented in a 0.25 um SiGe BiCMOS technology. The PA-cell has a wideband performance (38.6%) with both high peak efficiency (30%) and high saturated output power (24.9 dBm), which is the highest reported output power level obtained without the use of circuit-level power combining in Si-based technologies at Ka-band. In order to achieve the optimal system-level performance of the combined PA, an EM-circuit-thermal optimization flow has been proposed, which accounts for various multiphysics effects occurring in the joint structure. The final PA achieves the peak PAE of 26.7% in combination with 30.8 dBm maximum saturated output power, which is the highest achievable output power in practical applications, where the 50-Ohms load is placed on a laminate. The high efficiency (>20%) and output power (>29.8 dBm) over a wide frequency range (30%) exceed the state-of-the-art in Si-based PAs

KEY FRONT-END CIRCUITS IN MILLIMETER-WAVE SILICON-BASED WIRELESS TRANSMITTERS FOR PHASED-ARRAY APPLICATIONS

Millimeter-wave (mm-Wave) phased arrays have been widely used in numerous wireless systems to perform beam forming and spatial filtering that can enhance the equivalent isotropically radiated power (EIRP) for the transmitter (TX). Regarding the existing phased-array architectures, an mm-Wave transmitter includes several building blocks to perform the desired delivered power and phases for wireless communication. Power amplifier (PA) is the most important building block. It needs to offer several advantages, e.g., high efficiency, broadband operation and high linearity. With the recent escalation of interest in 5G wireless communication technologies, mm-Wave transceivers at the 5G frequency bands (e.g., 28 GHz, 37 GHz, 39 GHz, and 60 GHz) have become an important topic in both academia and industry. Thus, PA design is a critical obstacle due to the challenges associated with implementing wideband, highly efficient and highly linear PAs at mm-Wave frequencies. In this dissertation, we present several PA design innovations to address the aforementioned challenges. Additionally, phase shifter (PS) also plays a key role in a phased-array system, since it governs the beam forming quality and steering capabilities. A high-performance phase shifter should achieve a low insertion loss, a wide phase shifting range, dense phase shift angles, and good input/output matching.Ph.D

High-Efficiency Millimeter-Wave Front-Ends for Large Phased-Array Transmitters

The ever-increasing demand for wireless broadband connectivity requires infrastructure capable of supporting data transfer rates at multi-Gbps. To accommodate such heavy traffic, the channel capacity for the given spectrum must be utilized as efficiently as possible. Wideband millimeter-wave phased-array systems can enhance the capacity of the channel by providing multiple steerable directional beams. However the cost, complexity, and high power consumption of phased-array systems are key barriers to the commercialization of such technology. Silicon-based beam-former chips and scalable phased-array technology offer promising solutions to lower the cost of phased-array systems. However, the implementation of low-power phased-array architectures is still a challenge. Millimeter-wave power generation in silicon beam-formers suffers from low efficiency. The stringent linearity requirements for multi-beam wideband arrays further limits the achievable efficiency. In scalable phased-arrays, each module consists of an antenna sub-array and a beam-former chip that feeds the antenna elements. To improve efficiency, a design methodology that considers the beam-former chip and the antenna array as one entity is necessary. In this thesis, power-efficient solutions for a millimeter-wave phased-array transmitter are studied and different high-efficiency power amplifier structures for broadband applications are proposed. Initially, the design of a novel 27-30 GHz RF front-end consisting of a variable gain amplifier, a 360 degree phase shifter, and a two-stage linear power amplifier with output power of 12 dBm is described. It is fabricated using 0.13 $\mu m$ SiGe technology. This chip serves as the RF core of a beam-former chip with eight outputs for feeding a 2$\times$2 dual-feed sub-array. Such sub-arrays are used as part of large phased-arrays for SATCOM infrastructure. Measurement results show 26.7 \% total efficiency for the designed chip. The chip achieves the highest efficiency among Ka-band phased-array transmitters reported in the literature. In addition, original transformer-based output matching structures are proposed for harmonic-tuned power amplifiers. Harmonic-tuned power amplifiers have high peak-efficiency but their complicated output matching structure can limit their use in beam-former RF front-ends. The proposed output matching structures have the layout footprint of a transformer, making their use in beam-former chips feasible. A 26-38 GHz power amplifier based on a non-inverting 1:1 transformer is fabricated. A measured efficiency of more than 27 \% is achieved across the band with an output power of 12 dBm. Furthermore, two continuous class $F^{-1}$ power amplifiers using 1:1 inverting transformers are described. Simulation results show a peak-efficiency of 35 \% and output power of 12 dBm from 24 to 30 GHz. A common-base power amplifier with inverting transformer output matching is also demonstrated. This amplifier achieves a peak-efficiency of 42 \% and peak output power of 16 dBm. Finally, a low-loss Ka-band re-configurable output matching structure based on tunable lines is proposed and implemented. A double-stub matching structure with three tunable segments is proposed to maximize the impedance matching coverage. This structure can potentially compensate for the antenna impedance variation in phased-array antennas

Integrated Distributed Amplifiers for Ultra-Wideband BiCMOS Receivers Operating at Millimeter-Wave Frequencies

Millimetre-wave technology is used for applications such as telecommunications and imaging. For both applications, the bandwidth of existing systems has to be increased to support higher data rates and finer imaging resolutions. Millimetrewave circuits with very large bandwidths are developed in this thesis. The focus is put on amplifiers and the on-chip integration of the amplifiers with antennas. Circuit prototypes, fabricated in a commercially available 130nm Silicon-Germanium (SiGe) Bipolar Complementary Metal-Oxide-Semiconductor (BiCMOS) process, validated the developed techniques. Cutting-edge performances have been achieved in the field of distributed and resonant-matched amplifiers, as well as in that of the antenna-amplifier co-integration. Examples are as follows: - A novel cascode gain-cell with three transistors was conceived. By means of transconductance peaking towards high frequencies, the losses of the synthetic line can be compensated up to higher frequencies. The properties were analytically derived and explained. Experimental demonstration validated the technique by a Traveling-Wave Amplifier (TWA) able to produce 10 dB of gain over a frequency band of 170GHz.# - Two Cascaded Single-Stage Distributed Amplifiers (CSSDAs) have been demonstrated. The first CSSDA, optimized for low power consumption, requires less than 20mW to provide 10 dB of gain over a frequency band of 130 GHz. The second amplifier was designed for high-frequency operation and works up to 250 GHz leading to a record bandwidth for distributed amplifiers in SiGe technology. - The first complete CSSDA circuit analysis as function of all key parameters was presented. The typical degradation of the CSSDA output matching towards high frequencies was analytically quantified. A balanced architecture was then introduced to retain the frequency-response advantages of CSSDAs and yet ensure matching over the frequency band of interested. A circuit prototype validated experimentally the technique. - The first traveling-wave power combiner and divider capable of operation from the MHz range up to 200 GHz were demonstrated. The circuits improved the state of the art of the maximum frequency of operation and the bandwidth by a factor of five. - A resonant-matched balanced amplifier was demonstrated with a centre frequency of 185 GHz, 10 dB of gain and a 55GHz wide –3 dB-bandwidth. The power consumption of the amplifier is 16.8mW, one of the lowest for this circuit class, while the bandwidth is the broadest reported in literature for resonant-matched amplifiers in SiGe technology

Millimeter-Wave Concurrent Dual-Band BiCMOS RFIC Transmitter for Radar and Communication Systems

This dissertation presents new circuit architectures and techniques for improving the performance of several key BiCMOS RFIC building blocks used in radar and wireless communication systems operating up to millimeter-wave frequencies, and the development of an advanced, low-cost and miniature millimeter-wave concurrent dual-band transmitter for short-range, high-resolution radar and high-rate communication systems. A new type of low-power active balun consisting of a common emitter amplifier with degenerative inductor and a common collector amplifier is proposed. The parasitic neutralization and compensation techniques are used to keep the balun well balanced at very high frequencies and across an ultra-wide bandwidth. A novel RF switch architecture with ultra-high isolation and possible gain is proposed, analyzed and demonstrated. The new RF switch architecture achieves an ultra-high isolation through implementation of a new RF leaking cancellation technique. A new class of concurrent dual-band impedance matching networks and technique for synthesizing them are presented together with a 25.5/37-GHz concurrent dual-band PA. These matching networks enable simultaneous matching of two arbitrary loads to two arbitrary sources at two different frequencies, utilizing the impedance-equivalence properties of LC networks that any LC network can be equivalent to an inductor, capacitor, open or short at different frequencies. K- and Ka-band ultra-low-leakage RF-pulse formers capable of producing very narrow RF pulses in the order of 200 ps with small rising and falling time for short-range high-resolution radar and high-data-rate communication systems are also developed. The complete transmitter exhibiting unique characteristics obtained from capabilities of producing very narrow and tunable RF pulses with extremely RF leakage and working concurrently in dual bands at 24.5 and 35 GHz was designed. Capability of generating narrow and tunable RF pulses allows the radar system to flexibly work at high and multiple range resolutions. The extremely low RF leakage allows the transmitter to share one antenna system with receiver, turn on the PA at all time, comply the transmitting spectrum requirements, increase the system dynamic range, avoid harming to other systems; hence improving system size, cost and performance. High data-rate in communication systems is achieved as the consequence of transmitting very narrow RF pulses at high rates. In addition, the dissertation demonstrates a design approach for low chip-area, cost and power consumption systems in which a single dual-band component (power amplifier) is designed to operate with two RF signals simultaneously

Efficient and Linear CMOS Power Amplifier and Front-end Design for Broadband Fully-Integrated 28-GHz 5G Phased Arrays

Demand for data traffic on mobile networks is growing exponentially with time and on a global scale. The emerging fifth-generation (5G) wireless standard is being developed with millimeter-wave (mm-Wave) links as a key technological enabler to address this growth by a 2020 time frame. The wireless industry is currently racing to deploy mm-Wave mobile services, especially in the 28-GHz band. Previous widely-held perceptions of fundamental propagation limitations were overcome using phased arrays. Equally important for success of 5G is the development of low-power, broadband user equipment (UE) radios in commercial-grade technologies. This dissertation demonstrates design methodologies and circuit techniques to tackle the critical challenge of key phased array front-end circuits in low-cost complementary metal oxide semiconductor (CMOS) technology. Two power amplifier (PA) proof-of-concept prototypes are implemented in deeply scaled 28- nm and 40-nm CMOS processes, demonstrating state-of-the-art linearity and efficiency for extremely broadband communication signals. Subsequently, the 40 nm PA design is successfully embedded into a low-power fully-integrated transmit-receive front-end module. The 28 nm PA prototype in this dissertation is the first reported linear, bulk CMOS PA targeting low-power 5G mobile UE integrated phased array transceivers. An optimization methodology is presented to maximizing power added efficiency (PAE) in the PA output stage at a desired error vector magnitude (EVM) and range to address challenging 5G uplink requirements. Then, a source degeneration inductor in the optimized output stage is shown to further enable its embedding into a two-stage transformer-coupled PA. The inductor helps by broadening inter-stage impedance matching bandwidth, and helping to reduce distortion. Designed and fabricated in 1P7M 28 nm bulk CMOS and using a 1 V supply, the PA achieves +4.2 dBm/9% measured Pout/PAE at −25 dBc EVM for a 250 MHz-wide, 64-QAM orthogonal frequency division multiplexing (OFDM) signal with 9.6 dB peak-to-average power ratio (PAPR). The PA also achieves 35.5%/10% PAE for continuous wave signals at saturation/9.6dB back-off from saturation. To the best of the author’s knowledge, these are the highest measured PAE values among published K- and K a-band CMOS PAs to date. To drastically extend the communication bandwidth in 28 GHz-band UE devices, and to explore the potential of CMOS technology for more demanding access point (AP) devices, the second PA is demonstrated in a 40 nm process. This design supports a signal radio frequency bandwidth (RFBW) >3× the state-of-the-art without degrading output power (i.e. range), PAE (i.e. battery life), or EVM (i.e. amplifier fidelity). The three-stage PA uses higher-order, dual-resonance transformer matching networks with bandwidths optimized for wideband linearity. Digital gain control of 9 dB range is integrated for phased array operation. The gain control is a needed functionality, but it is largely absent from reported high-performance mm-Wave PAs in the literature. The PA is fabricated in a 1P6M 40 nm CMOS LP technology with 1.1 V supply, and achieves Pout/PAE of +6.7 dBm/11% for an 8×100 MHz carrier aggregation 64-QAM OFDM signal with 9.7 dB PAPR. This PA therefore is the first to demonstrate the viability of CMOS technology to address even the very challenging 5G AP/downlink signal bandwidth requirement. Finally, leveraging the developed PA design methodologies and circuits, a low power transmit-receive phased array front-end module is fully integrated in 40 nm technology. In transmit-mode, the front-end maintains the excellent performance of the 40 nm PA: achieving +5.5 dBm/9% for the same 8×100 MHz carrier aggregation signal above. In receive-mode, a 5.5 dB noise figure (NF) and a minimum third-order input intercept point (IIP₃) of −13 dBm are achieved. The performance of the implemented CMOS frontend is comparable to state-of-the-art publications and commercial products that were very recently developed in silicon germanium (SiGe) technologies for 5G communication