Pseudo-three-stage Miller op-amp with enhanced small-signal and large-signal performance

A simple technique to implement highly power efficient class AB-AB Miller op-amps is presented in this paper. It uses a composite input stage with resistive local common mode feedback that provides class AB operation to the input stage and essentially enhances the op-amp's effective transconductance gain, the dc open-loop gain, the gain-bandwidth product, and slew rate with just moderate increase in power dissipation. The experimental results of op-amps in strong inversion and subthreshold fabricated in a 130-nm standard CMOS technology validate the proposed approach. The op-amp has 9 V·pF/μs·μW large-signal figure of merit (FOM) and 17 MHz · pF/μW small-signal FOM with 1.2-V supply voltage. In subthreshold, the op-amp has 10 V · pF/μs · μW large-signal FOM and 92 MHz · pF/μW small-signal FOM with 0.5-V supply voltage.This work was supported by Grant TEC2016-80396- C2-R (AEI/FEDER)

Microelectromechanical Systems for Wireless Radio Front-ends and Integrated Frequency References.

Microelectromechanical systems (MEMS) have great potential in realizing chip-scale integrated devices for energy-efficient analog spectrum processing. This thesis presents the development of a new class of MEMS resonators and filters integrated with CMOS readout circuits for RF front-ends and integrated timing applications. Circuit-level innovations coupled with new device designs allowed for realizing integrated systems with improved performance compared to standalone devices reported in the literature. The thesis is comprised of two major parts. The first part of the thesis is focused on developing integrated MEMS timing devices. Fused silica is explored as a new structural material for fabricating high-Q vibrating micromechanical resonators. A piezoelectric-on-silica MEMS resonator is demonstrated with a high Q of more than 20,000 and good electromechanical coupling. A low phase noise CMOS reference oscillator is implemented using the MEMS resonator as a mechanical frequency reference. Temperature-stable operation of the MEMS oscillator is realized by ovenizing the platform using an integrated heater. In an alternative scheme, the intrinsic temperature sensitivity of MEMS resonators is utilized for temperature sensing, and active compensation for MEMS oscillators is realized by oven-control using a phase-locked loop (PLL). CMOS circuits are implemented for realizing the PLL-based low-power oven-control system. The active compensation technique realizes a MEMS oscillator with an overall frequency drift within +/- 4 ppm across -40 to 70 °C, without the need for calibration. The CMOS PLL circuits for oven-control is demonstrated with near-zero phase noise invasion on the MEMS oscillators. The properties of PLL-based compensation for realizing ultra-stable MEMS frequency references are studied. In the second part of the thesis, RF MEMS devices, including tunable capacitors, high-Q inductors, and ohmic switches, are fabricated using a surface micromachined integrated passive device (IPD) process. Using this process, an integrated ultra-wideband (UWB) filter has been demonstrated, showing low loss and a small form factor. To further address the issue of narrow in-band interferences in UWB communication, a tunable MEMS bandstop filter is integrated with the bandpass filter with more than an octave frequency tuning range. The bandstop filter can be optionally switched off by employing MEMS ohmic switches co-integrated on the same chip.PhDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/109069/1/zzwu_1.pd

Third International Symposium on Magnetic Suspension Technology

In order to examine the state of technology of all areas of magnetic suspension and to review recent developments in sensors, controls, superconducting magnet technology, and design/implementation practices, the Third International Symposium on Magnetic Suspension Technology was held at the Holiday Inn Capital Plaza in Tallahassee, Florida on 13-15 Dec. 1995. The symposium included 19 sessions in which a total of 55 papers were presented. The technical sessions covered the areas of bearings, superconductivity, vibration isolation, maglev, controls, space applications, general applications, bearing/actuator design, modeling, precision applications, electromagnetic launch and hypersonic maglev, applications of superconductivity, and sensors

CMOS current amplifiers : speed versus nonlinearity

This work deals with analogue integrated circuit design using various types of current-mode amplifiers. These circuits are analysed and realised using modern CMOS integration technologies. The dynamic nonlinearities of these circuits are discussed in detail as in the literature only linear nonidealities and static nonlinearities are conventionally considered. For the most important open-loop current-mode amplifier, the second-generation current-conveyor (CCII), a macromodel is derived that, unlike other reported macromodels, can accurately predict the common-mode behaviour in differential applications. Similarly, this model is used to describe the nonidealities of several other current-mode amplifiers because similar circuit structures are common in such amplifiers. With modern low-voltage CMOS-technologies, the current-mode operational amplifier and the high-gain current-conveyor (CCII∞) perform better than open-loop current-amplifiers. Similarly, unlike with conventional voltage-mode operational amplifiers, the large-signal settling behaviour of these two amplifier types does not degrade as CMOS-processes are scaled down. In this work, two 1 MHz 3rd -order low-pass continuous-time filters are realised with a 1.2 μm CMOS-process. These filters use a differential CCII∞ with linearised, dynamically biased output stages resulting in performance superior to most OTA-C filter realisations reported. Similarly, two logarithmic amplifier chips are designed and fabricated. The first circuit, implemented with a 1.2 μm BiCMOS-process, uses again a CCII∞. This circuit uses a pn-junction as a logarithmic feedback element. With a CCII∞ the constant gain-bandwidth product, typical of voltage-mode operational amplifiers, is avoided resulting in a constant 1 MHz bandwidth with a 60 dB signal amplitude range. The second current-mode logarithmic amplifier, based on piece-wise linear approximation of the logarithmic function by a cascade of limiting current amplifier stages, is realised in a standard 1.2 μm CMOS-process. The limiting level in these current amplifiers is less sensitive to process variation than in limiting voltage amplifiers resulting in exceptionally low temperature dependency of the logarithmic output signal. Additionally, along with this logarithmic amplifier a new current peak detectoris developed.reviewe

High Temperature Electronics Design for Aero Engine Controls and Health Monitoring

There is a growing desire to install electronic power and control systems in high temperature harsh environments to improve the accuracy of critical measurements, reduce the amount of cabling and to eliminate cooling systems. Typical target applications include electronics for energy exploration, power generation and control systems. Technical topics presented in this book include:• High temperature electronics market• High temperature devices, materials and assembly processes• Design, manufacture and testing of multi-sensor data acquisition system for aero-engine control• Future applications for high temperature electronicsHigh Temperature Electronics Design for Aero Engine Controls and Health Monitoring contains details of state of the art design and manufacture of electronics targeted towards a high temperature aero-engine application. High Temperature Electronics Design for Aero Engine Controls and Health Monitoring is ideal for design, manufacturing and test personnel in the aerospace and other harsh environment industries as well as academic staff and master/research students in electronics engineering, materials science and aerospace engineering

High Temperature Electronics Design for Aero Engine Controls and Health Monitoring

There is a growing desire to install electronic power and control systems in high temperature harsh environments to improve the accuracy of critical measurements, reduce the amount of cabling and to eliminate cooling systems. Typical target applications include electronics for energy exploration, power generation and control systems. Technical topics presented in this book include:• High temperature electronics market• High temperature devices, materials and assembly processes• Design, manufacture and testing of multi-sensor data acquisition system for aero-engine control• Future applications for high temperature electronicsHigh Temperature Electronics Design for Aero Engine Controls and Health Monitoring contains details of state of the art design and manufacture of electronics targeted towards a high temperature aero-engine application. High Temperature Electronics Design for Aero Engine Controls and Health Monitoring is ideal for design, manufacturing and test personnel in the aerospace and other harsh environment industries as well as academic staff and master/research students in electronics engineering, materials science and aerospace engineering

Biomimetic cochlea filters : from modelling, design to analogue VLSI implementation

This thesis presents a novel biomimetic cochlea filter which closely resembles the biological cochlea behaviour. The filter is highly feasible for analogue very-large-scale integration (VLSI) circuits, which leads to a micro-watt-power and millimetre-sized hardware implementation. By virtue of such features, the presented filter contributes to a solid foundation for future biologically-inspired audio signal processors. Unlike existing works, the presented filter is developed by taking direct inspirations from the physiologically measured results of the biological cochlea. Since the biological cochlea has prominently different characteristics of frequency response from low to high frequencies, the biomimetic cochlea filter is built by cascading three sub-filters accordingly: a 2nd-order bandpass filter for the constant gentle low-frequency response, a 2nd-order tunable low-pass filter for the variable and selective centre frequency response and a 5th-order elliptic filter for the ultra-steep roll-off at stop-band. As a proof of concept, a biomimetic cochlea filter bank is built to process audio signals, which demonstrates the highly discriminative spectral decomposition and high-resolution time-frequency analysis capabilities similar to the biological cochlea. The filter has simple representation in the Laplace domain which leads to a convenient analogue circuit realisation. A floating-active-inductor circuit cell is developed to build the corresponding RLC ladder for each of the three sub-filters. The circuits are designed based on complementary metal-oxide-semiconductor (CMOS) transistors for VLSI implementation. Non-ideal factors of CMOS transistors including parasitics, noise and mismatches are extensively analysed and consciously considered in the circuit design. An analogue VLSI chip is successfully fabricated using 0.35μ m CMOS process. The chip measurements demonstrate that the centre frequency response of the filter has about 20 dB wide gain tuning range and a high quality factor reaching maximally over 19. The filter has a 20 dB/decade constant gentle low-frequency tail and an over 300 dB/decade sharp stop-band roll-off slope. The measured results agree with the filter model expectations and are comparable with the biological cochlea characteristics. Each filter channel consumes as low as 59.5 ~90μ Wpower and occupies only 0.9 mm2 area. Besides, the biomimetic cochlea filter chip is characterised from a wide range of angles and the experimental results cover not only the auditory filter specifications but also the integrated circuit design considerations. Furthermore, following the progressive development of the acoustic resonator based on microelectro- mechanical systems (MEMS) technology, a MEMS-CMOS implementation of the proposed filter becomes possible in the future. A key challenge for such implementation is the low sensing capacitance of the MEMS resonator which suffers significantly from sensitivity degradation due to the parasitic capacitance. A novel MEMS capacitive interface circuit chip is additionally developed to solve this issue. As shown in the chip results, the interface circuit is able to cancel the parasitic capacitance and increase the sensitivity of capacitive sensors by 35 dB without consuming any extra power. Besides, the chopper-stabilisation technique is employed which effectively reduces the circuit flicker noise and offsets. Due to these features, the interface circuit chip is capable of converting a 7.5 fF capacitance change of a 1-Volt-biased 0.5 pF capacitive sensor pair into a 0.745 V signal-conditioned output while consuming only 165.2μ W power