High Performance Power Management Integrated Circuits for Portable Devices

abstract: Portable devices often require multiple power management IC (PMIC) to power different sub-modules, Li-ion batteries are well suited for portable devices because of its small size, high energy density and long life cycle. Since Li-ion battery is the major power source for portable device, fast and high-efficiency battery charging solution has become a major requirement in portable device application. In the first part of dissertation, a high performance Li-ion switching battery charger is proposed. Cascaded two loop (CTL) control architecture is used for seamless CC-CV transition, time based technique is utilized to minimize controller area and power consumption. Time domain controller is implemented by using voltage controlled oscillator (VCO) and voltage controlled delay line (VCDL). Several efficiency improvement techniques such as segmented power-FET, quasi-zero voltage switching (QZVS) and switching frequency reduction are proposed. The proposed switching battery charger is able to provide maximum 2 A charging current and has an peak efficiency of 93.3%. By configure the charger as boost converter, the charger is able to provide maximum 1.5 A charging current while achieving 96.3% peak efficiency. The second part of dissertation presents a digital low dropout regulator (DLDO) for system on a chip (SoC) in portable devices application. The proposed DLDO achieve fast transient settling time, lower undershoot/overshoot and higher PSR performance compared to state of the art. By having a good PSR performance, the proposed DLDO is able to power mixed signal load. To achieve a fast load transient response, a load transient detector (LTD) enables boost mode operation of the digital PI controller. The boost mode operation achieves sub microsecond settling time, and reduces the settling time by 50% to 250 ns, undershoot/overshoot by 35% to 250 mV and 17% to 125 mV without compromising the system stability.Dissertation/ThesisDoctoral Dissertation Electrical Engineering 201

A Novel Boost-Buck Converter Architecture for Improving Transient Response and Output-Voltage Ripple

Buck-boost converters are widely used in the development of DC-DC converters. Several techniques and algorithms have been introduced to improve the transient response of buck-boost converters. However, due to the opposite trends of the output current change and the output voltage change, undershoot or overshoot in the output voltage still seems to be inevitable. In order to overcome this problem, a novel boost-buck converter architecture is proposed to build a fast transient response DC-DC converter. The converter consists of a cascaded configuration of the boost and buck stages. The boost stage converts the input voltage to the shared capacitor voltage and the buck stage supplies energy to the load by converting the shared capacitor voltage to the output voltage. By harnessing the energy stored in the shared capacitor, the transient response of the boost buck converter can be improved to 2 µs in a step-up load current change of 1 A with an output-voltage ripple of 15 mV

POWER DISTRIBUTION ANALYSIS IN COMPLEX SYSTEMS

Electronic systems are continuously growing nowadays in every ambit and application; concepts like mobile systems, domotic, wireless monitoring are becoming very common, and the reason is the continuous reduction of the energy and time needed to collect, process and send information and data to the end user. The energy management complexity of these systems is increasing in parallel both in terms of efficiency and reliability, in order to increase the lifetime of the application and try to make it energy-autonomous, thus also the power management should not be seen only as an efficient energy conversion stage, but as a complex system which can now manage different energy sources, and ensure an uninterrupted power supply to the application. The problems that must be overcome increase as the number of scenarios where the end applications have to be used: this thesis aims to present some complex power distribution systems and provide a detailed analysis of the strategies necessary to make the solution reliable and efficient

Power Management Circuits for Front-End ASICs Employed in High Energy Physics Applications

The instrumentation of radiation detectors for high energy physics calls for the development of very low-noise application-specific integrated-circuits and demanding system-level design strategies, with a particular focus on the minimisation of inter-ference noise from power anagement circuitry. On the other hand, the aggressive pixelisation of sensors and associated front-end electronics, and the high radiation exposure at the innermost tracking and vertex detectors, requires radiation-aware design and radiation-tolerant deep sub-micron CMOS technologies. This thesis explores circuit design techniques towards radiation tolerant power management integrated circuits, targeting applications on particle detectors and monitoring of accelerator-based experiments, aerospace and nuclear applications. It addresses advantages and caveats of commonly used radiation-hard layout techniques, which often employ Enclosed Layout or H-shaped transistors, in respect to the use of linear transistors. Radiation tolerant designs for bandgap circuits are discussed, and two different topologies were explored. A low quiescent current bandgap for sub-1 V CMOS circuits is proposed, where the use of diode-connected MOSFETs in weak-inversion is explored in order to increase its radiation tolerance. An any-load stable LDO architecture is proposed, and three versions of the design using different layout techniques were implemented and characterised. In addition, a switched DC-DC Buck converter is also studied. For reasons concerning testability and silicon area, the controller of the Buck converter is on-chip, while the inductance and the power transistors are left on-board. A prototype test chip with power management IP blocks was fabricated, using a TSMC 65 nm CMOS technology. The chip features Linear, ELT and H-shape LDO designs, bandgap circuits and a Buck DC-DC converter. We discuss the design, layout and test results of the prototype. The specifications in terms of voltage range and output current capability are based on the requirements set for the integrated on-detector electronics of the new CGEM-IT tracker for the BESIII detector. The thesis discusses the fundamental aspects of the proposed on-detector electronics and provides an in-depth depiction of the front-end design for the readout ASIC

Techniques for low power analog, digital and mixed signal CMOS integrated circuit design

With the continuously expanding of market for portable devices such as wireless communication devices, portable computers, consumer electronics and implantable medical devices, low power is becoming increasingly important in integrated circuits. The low power design can increase operation time and/or utilize a smaller size and lighter-weight battery. In this dissertation, several low power complementary metal-oxide-semiconductor (CMOS) integrated circuit design techniques are investigated. A metal-oxide-semiconductor field effect transistor (MOSFET) can be operated at a lower voltage by forward-biasing the source-substrate junction. This approach has been investigated in detail and used to designing an ultra-low power CMOS operational amplifier for operation at ± 0.4 V. The issue of CMOS latchup and noise has been investigated in detail because of the forward biasing of the substrates of MOSFETs in CMOS. With increasing forward body-bias, the leakage current increases significantly. Dynamic threshold MOSFET (DTMOS) technique is proposed to overcome the drawback which is inherent in a forward-biased MOSFET. By using the DTMOS method with the forward source-body biased MOSFET, two low-power low-voltage CMOS VLSI circuits that of a CMOS analog multiplexer and a Schmitt trigger circuits are designed. In this dissertation, an adaptive body-bias technique is proposed. Adaptive body-bias voltage is generated for several operational frequencies. Another issue, which the chip design community is facing, is the development of portable, cost effective and low power supply voltage. This dissertation proposes a new cost-effective DC/DC converter design in standard 1.5 um n-well CMOS, which adopts a delay-line controller for voltage regulation

CMOS Design of Reconfigurable SoC Systems for Impedance Sensor Devices

La rápida evolución en el campo de los sensores inteligentes, junto con los avances en las tecnologías de la computación y la comunicación, está revolucionando la forma en que recopilamos y analizamos datos del mundo físico para tomar decisiones, facilitando nuevas soluciones que desempeñan tareas que antes eran inconcebibles de lograr.La inclusión en un mismo dado de silicio de todos los elementos necesarios para un proceso de monitorización y actuación ha sido posible gracias a los avances en micro (y nano) electrónica. Al mismo tiempo, la evolución de las tecnologías de procesamiento y micromecanizado de superficies de silicio y otros materiales complementarios ha dado lugar al desarrollo de sensores integrados compatibles con CMOS, lo que permite la implementación de matrices de sensores de alta densidad. Así, la combinación de un sistema de adquisición basado en sensores on-Chip, junto con un microprocesador como núcleo digital donde se puede ejecutar la digitalización de señales, el procesamiento y la comunicación de datos proporciona características adicionales como reducción del coste, compacidad, portabilidad, alimentación por batería, facilidad de uso e intercambio inteligente de datos, aumentando su potencial número de aplicaciones.Esta tesis pretende profundizar en el diseño de un sistema portátil de medición de espectroscopía de impedancia de baja potencia operado por batería, basado en tecnologías microelectrónicas CMOS, que pueda integrarse con el sensor, proporcionando una implementación paralelizable sin incrementar significativamente el tamaño o el consumo, pero manteniendo las principales características de fiabilidad y sensibilidad de un instrumento de laboratorio. Esto requiere el diseño tanto de la etapa de gestión de la energía como de las diferentes celdas que conforman la interfaz, que habrán de satisfacer los requisitos de un alto rendimiento a la par que las exigentes restricciones de tamaño mínimo y bajo consumo requeridas en la monitorización portátil, características que son aún más críticas al considerar la tendencia actual hacia matrices de sensores.A nivel de celdas, se proponen diferentes circuitos en un proceso CMOS de 180 nm: un regulador de baja caída de voltaje como unidad de gestión de energía, que proporciona una alimentación de 1.8 V estable, de bajo ruido, precisa e independiente de la carga para todo el sistema; amplificadores de instrumentación con una aproximación completamente diferencial, que incluyen una etapa de entrada de voltaje/corriente configurable, ganancia programable y ancho de banda ajustable, tanto en la frecuencia de corte baja como alta; un multiplicador para conformar la demodulación dual, que está embebido en el amplificador para optimizar consumo y área; y filtros pasa baja totalmente integrados, que actúan como extractores de magnitud de DC, con frecuencias de corte ajustables desde sub-Hz hasta cientos de Hz.<br /

Modelling and thermal analysis of a seismic borehole sensor: diploma 2015

Analysis and adaptation of an acquisition system for a seismometer to enable operation at high temperatures (up to 180 [°C]). The simulation software and thermal measurements are used to validate theoretical results

Optimal inductor current in boost DC/DC converters operating in burst mode under light-load conditions

This letter analyzes how the efficiency of boost dc/dc converters operating in burst mode under light-load conditions can be improved by an appropriate selection of the inductor current that transfers energy from the input to the output. A theoretical analysis evaluates the main power losses (fixed, conduction, and switching losses) involved in such converters, and how do they depend on the inductor current. This analysis shows that there is an optimal value of this current that causes minimum losses and, hence, maximum efficiency. These theoretical predictions are then compared with experimental data resulting from a commercial boost dc/dc converter (TPS61252), whose average inductor current is adjustable. Experimental results show that the use of the optimal inductor current, which was around 340 mA for an output voltage of 5 V, provides an efficiency increase of 7%.Peer ReviewedPostprint (author's final draft

Modeling and Design of High-Performance DC-DC Converters

The goal of the research that was pursued during this PhD is to eventually facilitate the development of high-performance, fast-switching DC-DC converters. High-switching frequency in switching mode power supplies (SMPS) can be exploited by reducing the output voltage ripple for the same size of passives (mainly inductors and capacitors) and improve overall system performance by providing a voltage supply with less unwanted harmonics to the subsystems that they support. The opposite side of the trade-off is also attractive for designers as the same amount of ripple can be achieved with smaller values of inductance and/or capacitance which can result in a physically smaller and potentially cheaper end product. Another benefit is that the spectrum of the resulting switching noise is shifted to higher frequencies which in turn allows designers to push the corner frequency of the control loop of the system higher without the switching noise affecting the behavior of the system. This in turn, is translated to a system capable of responding faster to strong transients that are common in modern systems that may contain microprocessors or other electronics that tend to consume power in bursts and may even require the use of features like dynamic voltage scaling to minimize the overall consumption of the system. While the analysis of the open loop behavior of a DC-DC converter is relatively straightforward, it is of limited usefulness as they almost always operate in closed loop and therefore can suffer from degraded stability. Therefore, it is important to have a way to simulate their closed loop behavior in the most efficient manner possible. The first chapter is dedicated to a library of technology-agnostic high-level models that can be used to improve the efficiency of transient simulations without sacrificing the ability to model and localize the different losses. This work also focuses further in fixed-frequency converters that employ Peak Current Mode Control (PCM) schemes. PCM schemes are frequently used due to their simple implementation and their ability to respond quickly to line transients since any change of the battery voltage is reflected in the slope of the rising inductor current which in turn is monitored by a fast internal control loop that is closed with the help of a current sensor. Most existing models for current sensors assume that they behave in an ideal manner with infinite bandwidth and ideal constant gain. These assumptions tend to be in significant error as the minimum on-time of the sensor and therefore the settling time requirements of the sensor are reduced. Some sensing architectures, like the ones that approximate the inductor current with the high-side switch current, can be even more complex to analyze as they require the use of extended masking time to prevent spike currents caused by the switch commutation to be injected to the output of the sensor and therefore the signal processing blocks of the control loop. In order to solve this issue, this work also proposes a current sensor model that is compatible with time averaged models of DC-DC converters and is able to predict the effects of static and transient non-idealities of the block on the behavior of a PCM DC-DC converter. Lastly, this work proposes a new 40 V, 6 A, fully-integrated, high-side current sensing circuit with a response time of 51 . The proposed sensor is able to achieve this performance with the help of a feedback resistance emulation technique that prevents the sensor from debiasing during its masking phase which tends to extend the response time of similar fully integrated sensors