Advanced single-chip temperature stabilization system for silicon MEMS resonators and gyroscopes

The main objective of this research is to develop temperature and frequency stabilization techniques for silicon MEMS oven-controlled crystal oscillators (MEMS OCXO) with high-frequency stability. The device was built upon an ovenized platform that used a micro-heater to adjust the temperature of the resonator. Structural resistance-based (Rstruc) temperature sensing was used to improve the self-temperature monitoring accuracy of the silicon MEMS resonator. An analog feedback micro-oven control loop and a feedforward digital calibration scheme were developed for a 77MHz MEMS oscillator, which achieved a ±0.3ppm frequency stability from -25°C to 85°C. An AC heating scheme was also developed to enable tighter integration of the resonator, temperature sensor (Rstruc) and heaters. This temperature stabilization technique was also applied to silicon MEMS mode-matched vibratory x/y-axis and z-axis gyroscopes on a single chip. The temperature-induced frequency change, scale factor and output bias variations were all reduced significantly. The complete interface circuit for the single-chip three axes gyroscopes were also developed with an innovative trans-impedance amplifier to reduce the input-referred noise. For the first time, the simultaneous operation of mode-matched vibratory 3-axis MEMS gyroscopes on a single chip was demonstrated.Ph.D

Optical wireless data transfer for rotor detection and diagnostics

A special application of optical wireless data transfer, namely on-line monitoring and diagnostic of rotors in turbines and engines, has been considered in this thesis. In this application, to maintain line of sight, i.e. data transfer, between a sensor placed on a rotating component inside the turbine and a monitoring point placed in a fixed position outside the turbine, a periodic fast fading channel is generated, which gives the transceivers more flexibility regarding their mounting location. The communication in such a channel is affected by the intermittency and variation of the signal power, which produces a unique channel condition that influences the performance of the optical transceiver. To investigate the channel condition and the error rate of the periodic fast fading channel with signal fluctuation, a model is developed to simulate the optical channel by considering the variation of signal power as a result of the change in the relative position of the photodiode with respect to the Lambertian radiation pattern of the LED, in a simplified linear geometry. The error rate is estimated using the Saddlepoint approximation on a specific threshold strategy. The results show that the channel can afford the sensor data transmission and the performance can be improved by modifying several parameters, such as geometrical distance, transmitter power and load resistor. Compared to a normal channel, a higher load resistor on the photodiode front end has the advantage of decreasing the noise level and increasing the data capacity in the fast fading channel. The analysis of the automatic gain control amplifier indicates that a higher load resistor needs a lower loop gain and from the model of the Transimpedance amplifier (TIA), the bandwidth extension from the amplifier is more significant for a higher resistor. In addition to the theoretical model, an experimental setup is built to emulate the channel in practice. The degree of similarity between the experimental setup and the theoretical model of the channel is estimated from the comparison of the generated communication windows. Since it has been found that differences exist in the duration of the communication window and the variation of the signal power, scaling factors to ensure their compatibility have been derived. Transceiver hardware which implemented the modelled functionality has been developed and a protocol to establish the communication with the required error rate has been proposed. Using the hardware implementation, a detection method for both rising and falling edges of the signal pulses and a threshold strategy have been demonstrated. The device power consumption is also estimated. What is more, the electromagnetic environment of a squirrel cage motor is simulated using the finite element method to investigate the interference and the possibility of providing power to the IR communication devices using power scavenging. In the conclusion, the key findings of the thesis are summarised. A solution is proposed for sensor data transfer using an optical channel for rotor monitoring applications, which involves the design of the IR transceiver, the implementation of the developed protocol and the power consumption estimation

Ultra Low Latency 71~76/81~86GHz E-band Radiolink Design

Department of Electrical EngineeringFor the special purpose of a time-sensitive system, such as a financial network, banking network, or medical network for real-time access in hospital, a very low latency of several tenths of a nano-second with a 1.25 Gbps transceiver is required. However, most commercial radiolinks are too slow at 5 ~ 350 ???s of latency through the use of Layer-2 topology with higher-level digital modulation. In this work, a unique topology of an ultra low latency transceiver was implemented by using high-speed ASK modulation with the scheme of physical Layer-1 transmission. In order to achieve a range of tenths of a nano-second of ultra-low latency with simple low cost, the direct conversion architecture was tried first. It was simple but still needed to be revised to address several problems. First, it was too difficult to build an ASK modulator directly at a 70/80 GHz millimeter-wave as it was too sensitive at its physical dimension. Secondly, the flatness was important, but it was difficult to secure the required bandwidth. Most of all, the conversion loss was significantly increased when the received power is low. In order to solve these problems, a heterodyne transceiver was considered. The ASK modulation was conducted at the IF stage. By adopting the heterodyne topology, the burdens of building an ultra wideband ASK modulator in 70/80 GHz millimeter-wave range was alleviated. However, building a 1.25 Gbps ASK modulator in the IF stage presented another new challenge. Several wide band design techniques were proposed as well as trial and error. According to the measurement results, the sensitivity was -45 dBm for 1.25 Gbps under BER 10-12, or error free, and one-way latency was measured by 19.1 ns, which is a superior achievement compared to existing commercial radiolinks worldwide. It was field tested at 4.1 km and showed a good match with its link budget. As a field proven solution, this research result has been partially adapted to a financial network in service between Chicago and New York.ope

Techniques for signal to noise ratio adaptation in infared optical wireless for optimisation of receiver performance

The challenge of creating a new environment of links for wireless infrared and optical local area networks (LANs) is driving new innovations in the design of optical transceivers. This thesis is concerned with a systematic approach to the design of receivers for indoor optical wireless communication. In particular, it is concerned with how to offer bandwidth adjustment capability in a receiver according to the dynamic service quality of the incoming signals. Another part of the discussion of the thesis is how one can properly choose the front-end preamplifier and biasing circuitry for the photodetector. Also, comparison is made between different types of amplifier, and the methods of bandwidth enhancement. The designs of six different techniques of integrating transimpedance amplifiers, with photodetectors to adapt an adjustable bandwidth control receiver are discussed. The proposed topologies provide an adjustable range of bandwidths for different frequency ranges, typically between 52Hz to 115MHz. The composite technique designs were used to incorporate into a system with an automatic gain control to study its effect, on an optical wireless receiver which had bandwidth adjustment and automatic gain adjustment. Theoretical analysis of noise performance for all the designed circuits is also presented. The theory and design of obstacles of indoor optical wireless receiver delivery, in addition to techniques for mitigating these effects, are discussed. This shows that infrared is a viable alternative to ratio for certain applications