A New Transmitted Reference Pulse Cluster Based Ultra-Wideband Transmitter Design

An energy efficient ultra-wideband (UWB) transmitter based on the novel transmitted reference pulse cluster (TRPC) modulation scheme is presented. The TRPC-UWB transmitter integrates, namely, wideband active baluns, wideband I-Q modulator based up-conversion mixer, and differential to single-ended converter. The integrated circuits of TRPC-UWB front end is designed and implemented in the 130-nm CMOS process technology. the measured worst-case carrier leakage suppression is 22.4 dBc, while the single sideband suppression is higher than 31.6 dBc, operating at the frequency from 3.1 GHz to 8.2 GHz. With adjustable data rate of 10 to 300 Mbps, the transmitter achieves a high energy efficiency of 38.4 pJ/pulse.Comment: 4 page, 8 figure

The Experimental UWB Link

The experimental results from simple ultra wideband link are presented. The UWB link consisting of typical broadband microwave circuits built of commercially available components is able to send and detect unmodulated broadband electrical pulses with 20 MHz pulse repetition frequency. The system operates with approximately 60% of fractional bandwidth in 4GHz band with spectral density of -140dBW/Hz

The BLIXER, a Wideband Balun-LNA-I/Q-Mixer Topology

This paper proposes to merge an I/Q current-commutating mixer with a noise-canceling balun-LNA. To realize a high bandwidth, the real part of the impedance of all RF nodes is kept low, and the voltage gain is not created at RF but in baseband where capacitive loading is no problem. Thus a high RF bandwidth is achieved without using inductors for bandwidth extension. By using an I/Q mixer with 25% duty-cycle LO waveform the output IF currents have also 25% duty-cycle, causing 2 times smaller DC-voltage drop after IF filtering. This allows for a 2 times increase in the impedance level of the IF filter, rendering more voltage gain for the same supply headroom. The implemented balun-LNA-I/Q-mixer topology achieves > 18 dB conversion gain, a flat noise figure < 5.5 dB from 500 MHz to 7 GHz, IIP2 = +20 dBm and IIP3 = -3 dBm. The core circuit consumes only 16 mW from a 1.2 V supply voltage and occupies less than 0.01 mm2 in 65 nm CMOS

A 1.2 V and 69 mW 60 GHz Multi-channel Tunable CMOS Receiver Design

A multi-channel receiver operating between 56 GHz and 70 GHz for coverage of different 60 GHz bands worldwide is implemented with a 90 nm Complementary Metal-Oxide Semiconductor (CMOS) process. The receiver containing an LNA, a frequency down-conversion mixer and a variable gain amplifier incorporating a band-pass filter is designed and implemented. This integrated receiver is tested at four channels of centre frequencies 58.3 GHz, 60.5 GHz, 62.6 GHz and 64.8 GHz, employing a frequency plan of an 8 GHz-intermediate frequency (IF). The achieved conversion gain by coarse gain control is between 4.8 dB–54.9 dB. The millimeter-wave receiver circuit is biased with a 1.2V supply voltage. The measured power consumption is 69 mW

Passive Mixer-based UWB Receiver with Low Loss, High Linearity and Noise-cancelling for Medical Applications

A double balanced passive mixer-based receiver operating in the 3-5 GHz UWB for medical applications is described in this paper. The receiver front-end circuit is composed of an inductorless low noise amplifier (LNA) followed by a fully differential voltage-driven double-balanced passive mixer. A duty cycle of 25% was chosen to eliminate overlap between LO signals, thereby improving receiver linearity. The LNA realizes a gain of 25.3 dB and a noise figure of 2.9 dB. The proposed receiver achieves an IIP3 of 3.14 dBm, an IIP2 of 17.5 dBm and an input return loss (S11) below -12.5dB. Designed in 0.18μm CMOS technology, the proposed mixer consumes 0.72pW from a 1.8V power supply. The designed receiver demonstrated a good ports isolation performance with LO_IF isolation of 60dB and RF_IF isolation of 78dB

An IR-UWB photonic distribution system

Experimental results are presented for a novel distribution system for an impulse radio ultra-wideband (UWB) radio signals employing a gain-switched laser. The pulse position modulated short optical pulses with a bit rate of 1.25 Gb/s are transmitted over fiber to a remote antenna unit, where the signal is converted to the electrical domain and undergoes spectral shaping to remove unwanted components according to UWB requirements. An experimental radio terminal has also been constructed to enable bit-error-rate measurements to be carried out. These experiments show that the optical distribution system will be capable of supporting the radio part of the system

A coupled-line balun for ultra-wideband single-balanced diode mixer

A multi-section coupled-line balun design for an ultra-wideband diode mixer is presented in this paper. The multi-section coupled-line balun was used to interface with the diode mixer in which it can deliver a good impedance matching between the diode mixer and input/output ports. The mixer design operates with a Local Oscillator (LO) power level of 10 dBm, Radio Frequency (RF) power level of -20 dBm and Intermediate Frequency (IF) of 100 MHz with the balun characteristic of 180° phase shift over UWB frequency (3.1 to 10.6 GHz), the mixer design demonstrated a good conversion loss of -8 to -16 dB over the frequency range from 3.1 to 10.6 GHz. Therefore, the proposed multi-section coupled-line balun for application of UWB mixer showed a good isolation between the mixer’s ports