Developing large-scale field-programmable analog arrays for rapid prototyping

Field-programmable analog arrays (FPAAs) provide a method for rapidly prototyping analog systems. While currently available FPAAs vary in architecture and interconnect design, they are often limited in size and flexibility. For FPAAs to be as useful and marketable as modern digital reconfigurable devices, new technologies must be explored to provide area efficient, accurately programmable analog circuitry that can be easily integrated into a larger digital/mixed signal system. By leveraging recent advances in floating gate transistors, a new generation of FPAAs are achievable that will dramatically advance the current state of the art in terms of size, functionality, and flexibility

Analysis and Design Methodologies for Switched-Capacitor Filter Circuits in Advanced CMOS Technologies

Analog filters are an extremely important block in several electronic systems, such as RF transceivers, data acquisition channels, or sigma-delta modulators. They allow the suppression of unwanted frequencies bands in a signal, improving the system’s performance. These blocks are typically implemented using active RC filters, gm-C filters, or switched-capacitor (SC) filters. In modern deep-submicron CMOS technologies, the transistors intrinsic gain is small and has a large variability, making the design of moderate and high-gain amplifiers, used in the implementation of filter blocks, extremely difficult. To avoid this difficulty, in the case of SC filters, the opamp can be replaced with a voltage buffer or a low-gain amplifier (< 2), simplifying the amplifier’s design and making it easier to achieve higher bandwidths, for the same power. However, due to the loss of the virtual ground node, the circuit becomes sensitive to the effects of parasitic capacitances, which effect needs to be compensated during the design process. This thesis addresses the task of optimizing SC filters (mainly focused on implementations using low-gain amplifiers), helping designers with the complex task of designing high performance SC filters in advanced CMOS technologies. An efficient optimization methodology is introduced, based on hybrid cost functions (equation-based/simulation-based) and using genetic algorithms. The optimization software starts by using equations in the cost function to estimate the filter’s frequency response reducing computation time, when compared with the electrical simulation of the circuit’s impulse response. Using equations, the frequency response can be quickly computed (< 1 s), allowing the use of larger populations in the genetic algorithm (GA) to cover the entire design space. Once the specifications are met, the population size is reduced and the equation-based design is fine-tuned using the more computationally intensive, but more accurate, simulation-based cost function, allowing to accurately compensate the parasitic capacitances, which are harder to estimate using equations. With this hybrid approach, it is possible to obtain the final optimized design within a reasonable amount of computation time. Two methods are described for the estimation of the filter’s frequency response. The first method is hierarchical in nature where, in the first step, the frequency response is optimized using the circuit’s ideal transfer function. The following steps are used to optimize circuits, at transistor level, to replace the ideal blocks (amplifier and switches) used in the first step, while compensating the effects of the circuit’s parasitic capacitances in the ideal design. The second method uses a novel efficient numerical methodology to obtain the frequency response of SC filters, based on the circuit’s first-order differential equations. The methodology uses a non-hierarchical approach, where the non-ideal effects of the transistors (in the amplifier and in the switches) are taken into consideration, allowing the accurate computation of the frequency response, even in the case of incomplete settling in the SC branches. Several design and optimization examples are given to demonstrate the performance of the proposed methods. The prototypes of a second order programmable bandpass SC filter and a 50 Hz notch SC filter have been designed in UMC 130 nm CMOS technology and optimized using the proposed optimization software with a supply voltage of 0.9 V. The bandpass SC filter has a total power consumption of 249 uW. The filter’s central frequency can be tuned between 3.9 kHz and 7.1 kHz, the gain between -6.4 dB and 12.6 dB, and the quality factor between 0.9 and 6.9. Depending on the bit configuration, the circuit’s THD is between -54.7 dB and -61.7 dB. The 50 Hz notch SC filter has a total power consumption of 273 uW. The transient simulation of the circuit’s extracted view (C+CC) shows an attenuation of 52.3 dB in the 50 Hz interference and that the desired 5 kHz signal has a THD of -92.3 dB

Low-Power and Programmable Analog Circuitry for Wireless Sensors

Embedding networks of secure, wirelessly-connected sensors and actuators will help us to conscientiously manage our local and extended environments. One major challenge for this vision is to create networks of wireless sensor devices that provide maximal knowledge of their environment while using only the energy that is available within that environment. In this work, it is argued that the energy constraints in wireless sensor design are best addressed by incorporating analog signal processors. The low power-consumption of an analog signal processor allows persistent monitoring of multiple sensors while the device\u27s analog-to-digital converter, microcontroller, and transceiver are all in sleep mode. This dissertation describes the development of analog signal processing integrated circuits for wireless sensor networks. Specific technology problems that are addressed include reconfigurable processing architectures for low-power sensing applications, as well as the development of reprogrammable biasing for analog circuits

Low-Power and Programmable Analog Circuitry for Wireless Sensors

Embedding networks of secure, wirelessly-connected sensors and actuators will help us to conscientiously manage our local and extended environments. One major challenge for this vision is to create networks of wireless sensor devices that provide maximal knowledge of their environment while using only the energy that is available within that environment. In this work, it is argued that the energy constraints in wireless sensor design are best addressed by incorporating analog signal processors. The low power-consumption of an analog signal processor allows persistent monitoring of multiple sensors while the device\u27s analog-to-digital converter, microcontroller, and transceiver are all in sleep mode. This dissertation describes the development of analog signal processing integrated circuits for wireless sensor networks. Specific technology problems that are addressed include reconfigurable processing architectures for low-power sensing applications, as well as the development of reprogrammable biasing for analog circuits

A 1000 FPS at 128×128 vision processor with 8-bit digitized I/O

This paper presents a mixed-signal programmable chip for high-speed vision applications. It consists of an array of processing elements, arranged to operate in accordance with the principles of single instruction multiple data (SIMD) computing architectures. This chip, implemented in a 0.35-μm fully digital CMOS technology, contains ∼ 3.75 M transistors and exhibits peak performance figures of 330 GOPS (8-bit equivalent giga-operations per second), 3.6 GOPS/mm2 and 82.5 GOPS/W. It includes structures for image acquisition and for image processing, meaning that it does not require a separate imager for operation. At the sensory side, integration and log-compression sensing circuits are embedded, thus allowing the chip to handle a large variety of illumination conditions. At the processing plane, analog and digital circuits are employed whose parameters can be programmed and their architecture reconfigured for the realization of software-coded processing algorithms. The chip provides, and accepts, 8-bit digitized data through a 32-bit bidirectional data bus which operates at 120 MB/s. Experimental results show that frame rates of 1000 frames per second (FPS) can be achieved under room illumination conditions; applications using exposures of about 50 μs have been recently reached by using special illumination setups. The chip can capture an image, run approximately 150 two-dimensional linear convolutions, and download the result in 8-bit digital format, in less than 1 ms. This feature, together with the possibility of executing sequences of user-definable instructions (stored on a full-custom 32-kb on-chip memory), and storing intermediate results (up to 8 grayscale images) makes the chip a true general-purpose sensory/processing device.European Commission IST-2001-38097Office of Naval Research (USA) N00014021088

Analog signal processing on a reconfigurable platform

The Cooperative Analog/Digital Signal Processing (CADSP) research group's approach to signal processing is to see what opportunities lie in adjusting the line between what is traditionally computed in digital and what can be done in analog. By allowing more computation to be done in analog, we can take advantage of its low power, continuous domain operation, and parallel capabilities. One setback keeping Analog Signal Processing (ASP) from achieving more wide-spread use, however, is its lack of programmability. The design cycle for a typical analog system often involves several iterations of the fabrication step, which is labor intensive, time consuming, and expensive. These costs in both time and money reduce the likelihood that engineers will consider an analog solution. With CADSP's development of a reconfigurable analog platform, a Field-Programmable Analog Array (FPAA), it has become much more practical for systems to incorporate processing in the analog domain. In this Thesis, I present an entire chain of tools that allow one to design simply at the system block level and then compile that design onto analog hardware. This tool chain uses the Simulink design environment and a custom library of blocks to create analog systems. I also present several of these ASP blocks, covering a broad range of functions from matrix computation to interfacing. In addition to these tools and blocks, the most recent FPAA architectures are discussed. These include the latest RASP general-purpose FPAAs as well as an adapted version geared toward high-speed applications.M.S.Committee Chair: Hasler, Paul; Committee Member: Anderson, David; Committee Member: Ghovanloo, Maysa

A design for testability study on a high performance automatic gain control circuit.

A comprehensive testability study on a commercial automatic gain control circuit is presented which aims to identify design for testability (DfT) modifications to both reduce production test cost and improve test quality. A fault simulation strategy based on layout extracted faults has been used to support the study. The paper proposes a number of DfT modifications at the layout, schematic and system levels together with testability. Guidelines that may well have generic applicability. Proposals for using the modifications to achieve partial self test are made and estimates of achieved fault coverage and quality levels presente

A systematic approach to circuit design and analysis: classification of Two-VCCS Circuits

This paper discusses a systematic approach to the design and analysis of circuits, using a transconductor or voltage controlled current source (VCCS) as a building block. It is shown that two independent Kirchhoff relations among the VCCS voltages and currents play a crucial role in establishing a unique transfer function in two-port circuits with two VCCSs. A class of two VCCS circuits is defined, which can be subdivided into three main classes and 14 subclasses, based on different imposable sets of two Kirchhoff relations. The classification is useful for circuit synthesis and analysis, as it reveals all the basically different ways to exploit two VCCS's, and allows for a unified analysis of classes of circuits. To exemplify this, all complementary metal-oxide-semiconductor (CMOS) V-I converter kernels, based on two matched MOS transistor (MOST)-VCCSs, are generated and analyzed with respect to distortion. It is shown that dozens of published transconductor circuits can be classified in only four classes, with essentially different distortion behavio

A cooperative cellular and broadcast conditional access system for Pay-TV systems

This is the author's accepted manuscript. The final published article is available from the link below. Copyright @ 2009 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other users, including reprinting/ republishing this material for advertising or promotional purposes, creating new collective works for resale or redistribution to servers or lists, or reuse of any copyrighted components of this work in other works.The lack of interoperability between Pay-TV service providers and a horizontally integrated business transaction model have compromised the competition in the Pay-TV market. In addition, the lack of interactivity with customers has resulted in high churn rate and improper security measures have contributed into considerable business loss. These issues are the main cause of high operational costs and subscription fees in the Pay-TV systems. As a result, this paper presents the Mobile Conditional Access System (MICAS) as an end-to-end access control solution for Pay-TV systems. It incorporates the mobile and broadcasting systems and provides a platform whereby service providers can effectively interact with their customers, personalize their services and adopt appropriate security measurements. This would result in the decrease of operating expenses and increase of customers' satisfaction in the system. The paper provides an overview of state-of-the-art conditional access solutions followed by detailed description of design, reference model implementation and analysis of possible MICAS security architectures.Strategy & Technology (S&T) Lt