Layout area models for high-level synthesis

Traditionally, the common cost functions, the number of functional units, registers and selector inputs, are used in high level synthesis as quality measures. However, these traditional design quality measures may not reflect the real physical design. To establish quality measures based on the physical designs, we propose layout estimation models for two commonly used data path and control layout architectures. The results show that quality measures deriving from our models give an accurate prediction of the final layout. The results also show that traditional cost functions are not good indicators for optimization in high level synthesis

Turbo NOC: a framework for the design of Network On Chip based turbo decoder architectures

This work proposes a general framework for the design and simulation of network on chip based turbo decoder architectures. Several parameters in the design space are investigated, namely the network topology, the parallelism degree, the rate at which messages are sent by processing nodes over the network and the routing strategy. The main results of this analysis are: i) the most suited topologies to achieve high throughput with a limited complexity overhead are generalized de-Bruijn and generalized Kautz topologies; ii) depending on the throughput requirements different parallelism degrees, message injection rates and routing algorithms can be used to minimize the network area overhead.Comment: submitted to IEEE Trans. on Circuits and Systems I (submission date 27 may 2009

Tensor Computation: A New Framework for High-Dimensional Problems in EDA

Many critical EDA problems suffer from the curse of dimensionality, i.e. the very fast-scaling computational burden produced by large number of parameters and/or unknown variables. This phenomenon may be caused by multiple spatial or temporal factors (e.g. 3-D field solvers discretizations and multi-rate circuit simulation), nonlinearity of devices and circuits, large number of design or optimization parameters (e.g. full-chip routing/placement and circuit sizing), or extensive process variations (e.g. variability/reliability analysis and design for manufacturability). The computational challenges generated by such high dimensional problems are generally hard to handle efficiently with traditional EDA core algorithms that are based on matrix and vector computation. This paper presents "tensor computation" as an alternative general framework for the development of efficient EDA algorithms and tools. A tensor is a high-dimensional generalization of a matrix and a vector, and is a natural choice for both storing and solving efficiently high-dimensional EDA problems. This paper gives a basic tutorial on tensors, demonstrates some recent examples of EDA applications (e.g., nonlinear circuit modeling and high-dimensional uncertainty quantification), and suggests further open EDA problems where the use of tensor computation could be of advantage.Comment: 14 figures. Accepted by IEEE Trans. CAD of Integrated Circuits and System

Power Reductions with Energy Recovery Using Resonant Topologies

The problem of power densities in system-on-chips (SoCs) and processors has become more exacerbated recently, resulting in high cooling costs and reliability issues. One of the largest components of power consumption is the low skew clock distribution network (CDN), driving large load capacitance. This can consume as much as 70% of the total dynamic power that is lost as heat, needing elaborate sensing and cooling mechanisms. To mitigate this, resonant clocking has been utilized in several applications over the past decade. An improved energy recovering reconfigurable generalized series resonance (GSR) solution with all the critical support circuitry is developed in this work. This LC resonant clock driver is shown to save about 50% driver power (\u3e40% overall), on a 22nm process node and has 50% less skew than a non-resonant driver at 2GHz. It can operate down to 0.2GHz to support other energy savings techniques like dynamic voltage and frequency scaling (DVFS). As an example, GSR can be configured for the simpler pulse series resonance (PSR) operation to enable further power saving for double data rate (DDR) applications, by using de-skewing latches instead of flip-flop banks. A PSR based subsystem for 40% savings in clocking power with 40% driver active area reduction xii is demonstrated. This new resonant driver generates tracking pulses at each transition of clock for dual edge operation across DVFS. PSR clocking is designed to drive explicit-pulsed latches with negative setup time. Simulations using 45nm IBM/PTM device and interconnect technology models, clocking 1024 flip-flops show the reductions, compared to non-resonant clocking. DVFS range from 2GHz/1.3V to 200MHz/0.5V is obtained. The PSR frequency is set \u3e3× the clock rate, needing only 1/10th the inductance of prior-art LC resonance schemes. The skew reductions are achieved without needing to increase the interconnect widths owing to negative set-up times. Applications in data circuits are shown as well with a 90nm example. Parallel resonant and split-driver non-resonant configurations as well are derived from GSR. Tradeoffs in timing performance versus power, based on theoretical analysis, are compared for the first time and verified. This enables synthesis of an optimal topology for a given application from the GSR

Behavioral, Parameterized, and Broadband Modeling of Wired Interconnects with Internal Discontinuities

We present a complete workflow for the extraction of behavioral reduced-order models of wired interconnect links, including an explicit dependence on geometrical or material parameters describing internal discontinuities that may affect the quality of signal transmission. Thanks to the adopted structure, the models are easily identified from sampled frequency responses at discrete points in the parameter space. Such responses are obtained from off-the-shelf full-wave solvers. A novel algorithm is used for checking and enforcing model stability and passivity, two fundamental requirements for reliably running stable transient simulations. Finally, an ad hoc procedure is devised to synthesize the models as parameterized circuit equivalents, compatible with any SPICE solver. Several examples illustrate and validate the workflow, confirming the suitability of the proposed approach for what-if, parameter sweep, design centering, and optimization through time-domain simulations, possibly including nonlinear devices and terminations

A low cost reconfigurable soft processor for multimedia applications: design synthesis and programming model

This paper presents an FPGA implementation of a low cost 8 bit reconfigurable processor core for media processing applications. The core is optimized to provide all basic arithmetic and logic functions required by the media processing and other domains, as well as to make it easily integrable into a 2D array. This paper presents an investigation of the feasibility of the core as a potential soft processing architecture for FPGA platforms. The core was synthesized on the entire Virtex FPGA family to evaluate its overall performance, scalability and portability. A special feature of the proposed architecture is its simple programming model which allows low level programming. Throughput results for popular benchmarks coded using the programming model and cycle accurate simulator are presented

Comparing energy and latency of asynchronous and synchronous NoCs for embedded SoCs

Journal ArticlePower consumption of on-chip interconnects is a primary concern for many embedded system-on-chip (SoC) applications. In this paper, we compare energy and performance characteristics of asynchronous (clockless) and synchronous network on-chip implementations, optimized for a number of SoC designs. We adapted the COSI-2.0 framework with ORION 2.0 router and wire models for synchronous network generation. Our own tool, ANetGen, specifies the asynchronous network by determining the topology with simulated-annealing and router locations with force-directed placement. It uses energy and delay models from our 65 nm bundled-data router design. SystemC simulations varied traffic burstiness using the self-similar b-model. Results show that the asynchronous network provided lower median and maximum message latency, especially under bursty traffic, and used far less router energy with a slight overhead for the interrouter wires