Recursive receiver down-converters with multiband feedback and gain-reuse for low-power applications

Power minimization in wireless transceivers has become increasingly critical in recent years with the emergence of standards for short-distance applications in the 900 MHz and 2.4 GHz industrial, scientific and medical (ISM) radio bands. The demand for long battery life and better portability in such applications has led to extensive research on low power radio architectures. This dissertation introduces receiver topologies for low-power systems and presents a theoretical performance analysis of the topologies. Two fully integrated receiver down-converters that demonstrate the concept are implemented in a 0.13-[mu]m CMOS technology. These topologies employ merged mixers and IF amplifiers in order to reduce power dissipation for a given dynamic range performance. In the described topologies, the input stage of a mixer is used to simultaneously provide conversion gain and baseband amplification. This is achieved by applying the down-converted IF signal to input of the mixer. Consequently, the effective conversion gain of the design is greatly enhanced with current requirement primarily determined by the input transconductor. Potential degradation mechanisms related to instability and second-order distortion are identified and solved by the use of appropriate circuit techniques. Noise and linearity performance of the down-converters is analyzed and compared to that of conventional cascaded design counterparts. The potential for enhancement of IIP3 performance through cancellation of nonlinear products is discussed. Potential extensions of the above work including feedback-based architectures that exploit multiple loops for further maximizing the power efficiency of receiver front-ends are also presented.Electrical and Computer Engineerin

Ultra Wideband

Ultra wideband (UWB) has advanced and merged as a technology, and many more people are aware of the potential for this exciting technology. The current UWB field is changing rapidly with new techniques and ideas where several issues are involved in developing the systems. Among UWB system design, the UWB RF transceiver and UWB antenna are the key components. Recently, a considerable amount of researches has been devoted to the development of the UWB RF transceiver and antenna for its enabling high data transmission rates and low power consumption. Our book attempts to present current and emerging trends in-research and development of UWB systems as well as future expectations

Radio-Communications Architectures

Wireless communications, i.e. radio-communications, are widely used for our different daily needs. Examples are numerous and standard names like BLUETOOTH, WiFI, WiMAX, UMTS, GSM and, more recently, LTE are well-known [Baudoin et al. 2007]. General applications in the RFID or UWB contexts are the subject of many papers. This chapter presents radio-frequency (RF) communication systems architecture for mobile, wireless local area networks (WLAN) and connectivity terminals. An important aspect of today's applications is the data rate increase, especially in connectivity standards like WiFI and WiMAX, because the user demands high Quality of Service (QoS). To increase the data rate we tend to use wideband or multi-standard architecture. The concept of software radio includes a self-reconfigurable radio link and is described here on its RF aspects. The term multi-radio is preferred. This chapter focuses on the transmitter, yet some considerations about the receiver are given. An important aspect of the architecture is that a transceiver is built with respect to the radio-communications signals. We classify them in section 2 by differentiating Continuous Wave (CW) and Impulse Radio (IR) systems. Section 3 is the technical background one has to consider for actual applications. Section 4 summarizes state-of-the-art high data rate architectures and the latest research in multi-radio systems. In section 5, IR architectures for Ultra Wide Band (UWB) systems complete this overview; we will also underline the coexistence and compatibility challenges between CW and IR systems

Wireless wire - ultra-low-power and high-data-rate wireless communication systems

With the rapid development of communication technologies, wireless personal-area communication systems gain momentum and become increasingly important. When the market gets gradually saturated and the technology becomes much more mature, new demands on higher throughput push the wireless communication further into the high-frequency and high-data-rate direction. For example, in the IEEE 802.15.3c standard, a 60-GHz physical layer is specified, which occupies the unlicensed 57 to 64 GHz band and supports gigabit links for applications such as wireless downloading and data streaming. Along with the progress, however, both wireless protocols and physical systems and devices start to become very complex. Due to the limited cut-off frequency of the technology and high parasitic and noise levels at high frequency bands, the power consumption of these systems, especially of the RF front-ends, increases significantly. The reason behind this is that RF performance does not scale with technology at the same rate as digital baseband circuits. Based on the challenges encountered, the wireless-wire system is proposed for the millimeter wave high-data-rate communication. In this system, beamsteering directional communication front-ends are used, which confine the RF power within a narrow beam and increase the level of the equivalent isotropic radiation power by a factor equal to the number of antenna elements. Since extra gain is obtained from the antenna beamsteering, less front-end gain is required, which will reduce the power consumption accordingly. Besides, the narrow beam also reduces the interference level to other nodes. In order to minimize the system average power consumption, an ultra-low power asynchronous duty-cycled wake-up receiver is added to listen to the channel and control the communication modes. The main receiver is switched on by the wake-up receiver only when the communication is identified while in other cases it will always be in sleep mode with virtually no power consumed. Before transmitting the payload, the event-triggered transmitter will send a wake-up beacon to the wake-up receiver. As long as the wake-up beacon is longer than one cycle of the wake-up receiver, it can be captured and identified. Furthermore, by adopting a frequency-sweeping injection locking oscillator, the wake-up receiver is able to achieve good sensitivity, low latency and wide bandwidth simultaneously. In this way, high-data-rate communication can be achieved with ultra-low average power consumption. System power optimization is achieved by optimizing the antenna number, data rate, modulation scheme, transceiver architecture, and transceiver circuitries with regards to particular application scenarios. Cross-layer power optimization is performed as well. In order to verify the most critical elements of this new approach, a W-band injection-locked oscillator and the wake-up receiver have been designed and implemented in standard TSMC 65-nm CMOS technology. It can be seen from the measurement results that the wake-up receiver is able to achieve about -60 dBm sensitivity, 10 mW peak power consumption and 8.5 µs worst-case latency simultaneously. When applying a duty-cycling scheme, the average power of the wake-up receiver becomes lower than 10 µW if the event frequency is 1000 times/day, which matches battery-based or energy harvesting-based wireless applications. A 4-path phased-array main receiver is simulated working with 1 Gbps data rate and on-off-keying modulation. The average power consumption is 10 µW with 10 Gb communication data per day

Validation platform specification – D5.1

Deliverable D5.1 del projecte Europeu OneFIT (ICT-2009-257385)The present deliverable introduces the OneFIT Proof-of-Concept (PoC) Architecture which will be used as a basis for the validation platform development throughout the project. This PoC Architecture proposal is validated by identifying the roles of the various components in the framework of the OneFIT Scenarios as derived and detailed in WP2. The applied methodology ensures that all required features are appropriately considered. Furthermore, the hardware components available to the project are detailed which are the basis for the development of an integrated validation platform. Their role is highlighted by an instantiation step which maps the PoC Architecture components to the identified hardware components. Finally, a scenario instantiation is derived which illustrates the role of the various hardware components for the validation of selected OneFIT scenarios.Postprint (published version