Symbolic framework for linear active circuits based on port equivalence using limit variables

Published versio

Determination of Stray Inductance of Low-Inductive Laminated Planar Multiport Busbars Using Vector Synthesis Method

Laminated busbars connect capacitors with switching power modules, and they are designed to have low stray inductance to minimize electromagnetic interference. Attempts to accurately measure the stray inductance of these busbars have not been successful. The challenge lies with the capacitors, as they excite the busbar producing their individual stray inductances. These individual stray inductances cannot be arithmetically averaged to establish the total stray inductance that applies when all the capacitors excite the busbar at the same time. It is also not possible to measure the stray inductance by simultaneous excitation of each capacitor port using impedance analyzers. This paper presents a solution to the above dilemma. A vector synthesis method is proposed, whereby the individual stray inductance from each capacitor port is measured using an impedance analyzer. Each stray inductance is then mapped into an xyz frame with a distinct direction. This mapping exercise allows the data to be vectored. The total stray inductance is then the sum of all the vectors. The effectiveness of the proposed method is demonstrated on a busbar designed for H-bridge inverters by comparing the simulation and practical results. The absolute error of the total stray inductance between the simulation and the proposed method is 0.48 nH. The proposed method improves the accuracy by 14.9% compared to the conventional technique in measuring stray inductances

Design of a 12 channel fm microwave receiver

The design, fabrication, and performance of elements of a low cost FM microwave satellite ground station receiver is described. It is capable of accepting 12 contiguous color television equivalent bandwidth channels in the 11.72 to 12.2 GHz band. Each channel is 40 MHz wide and incorporates a 4 MHz guard band. The modulation format is wideband FM and the channels are frequency division multiplexed. Twelve independent CATV compatible baseband outputs are provided. The overall system specifications are first discussed, then consideration is given to the receiver subsystems and the signal branching network

Program on application of communications satellites to educational development: Design of a 12 channel FM microwave receiver

The design, fabrication, and performance of elements of a low cost FM microwave satellite ground station receiver is described. It is capable of accepting 12 contiguous color television equivalent bandwidth channels in the 11.72 to 12.2 GHz band. Each channel is 40 MHz wide and incorporates a 4 MHz guard band. The modulation format is wideband FM and the channels are frequency division multiplexed. Twelve independent CATV compatible baseband outputs are provided. The overall system specifications are first discussed, then consideration is given to the receiver subsystems and the signal branching network

A wideband linear tunable CDTA and its application in field programmable analogue array

This document is the Accepted Manuscript version of the following article: Hu, Z., Wang, C., Sun, J. et al. ‘A wideband linear tunable CDTA and its application in field programmable analogue array’, Analog Integrated Circuits and Signal Processing, Vol. 88 (3): 465-483, September 2016. Under embargo. Embargo end date: 6 June 2017. The final publication is available at Springer via https://link.springer.com/article/10.1007%2Fs10470-016-0772-7 © Springer Science+Business Media New York 2016In this paper, a NMOS-based wideband low power and linear tunable transconductance current differencing transconductance amplifier (CDTA) is presented. Based on the NMOS CDTA, a novel simple and easily reconfigurable configurable analogue block (CAB) is designed. Moreover, using the novel CAB, a simple and versatile butterfly-shaped FPAA structure is introduced. The FPAA consists of six identical CABs, and it could realize six order current-mode low pass filter, second order current-mode universal filter, current-mode quadrature oscillator, current-mode multi-phase oscillator and current-mode multiplier for analog signal processing. The Cadence IC Design Tools 5.1.41 post-layout simulation and measurement results are included to confirm the theory.Peer reviewedFinal Accepted Versio

Realization of an Inductance Scale Traceable to the Quantum Hall Effect Using an Automated Synchronous Sampling System

In this paper, the realization of an inductance scale from 1~$\mu$H to 10~H for frequencies ranging between 50~Hz to 20~kHz is presented. The scale is realized directly from a series of resistance standards using a fully automated synchronous sampling system. A careful systematic characterization of the system shows that the lowest uncertainties, around 12~$\mu$H/H, are obtained for inductances in the range from 10~mH to 100~mH at frequencies in the kHz range. This new measurement system which was successfully evaluated during an international comparison, provides a primary realization of the henry, directly traceable to the quantum Hall effect. An additional key feature of this system is its versatility. In addition to resistance-inductance (R-L) comparison, any kind of impedances can be compared: R-R, R-C, L-L or C-C, giving this sampling system a great potential of use in many laboratories around the world

Low cost ground receiving systems for television signals from high powered communications satellites, volume 1

The fabrication and evaluation of 10 engineering prototype ground signal processing systems of three converter types are reported for use with satellite television. Target cost converters and cost sensitivity analysis are discussed along with the converter configurations

EMI measurement and modeling techniques for complex electronic circuits and modules

This dissertation consists of four papers. In the first paper, a combined model for predicting the most critical radiated emissions and total radiated power due to the display signals in a TV by incorporating the main processing board using the Huygens Equivalence theorem and the radiation due to the flex cable based on active probe measurements was developed. In the second paper, a frequency-tunable resonant magnetic field probe was designed in the frequency range 900-2260 MHz for near-field scanning applications for the radio frequency interference studies by using a varactor diode providing the required capacitance and the parasitic inductance of a magnetic field loop (i.e., a parallel LC circuit). Measurement results showed good agreement with the simulated results. In the third paper, a wideband microwave method was developed as a means for rapid detection of slight dissimilarities (including counterfeit) and aging effects in integrated circuits (ICs) based on measuring the complex reflection coefficient of an IC when illuminated with an open-ended rectangular waveguide probe, at K-band (18-26.5 GHz) and Ka-band (26.5-40 GHz) microwave frequencies. In the fourth paper, a method to predict radiated emissions from DC-DC converters with cables attached on the input side to a LISN and on the output side to a DC brushless motor as load based on linear terminal equivalent circuit modeling was demonstrated. The linear terminal equivalent model was extracted using measured input and output side common mode currents for various characterization impedances connected at the input and output terminals of the converter --Abstract, page iv

Baseband analog front-end and digital back-end for reconfigurable multi-standard terminals

Multimedia applications are driving wireless network operators to add high-speed data services such as Edge (E-GPRS), WCDMA (UMTS) and WLAN (IEEE 802.11a,b,g) to the existing GSM network. This creates the need for multi-mode cellular handsets that support a wide range of communication standards, each with a different RF frequency, signal bandwidth, modulation scheme etc. This in turn generates several design challenges for the analog and digital building blocks of the physical layer. In addition to the above-mentioned protocols, mobile devices often include Bluetooth, GPS, FM-radio and TV services that can work concurrently with data and voice communication. Multi-mode, multi-band, and multi-standard mobile terminals must satisfy all these different requirements. Sharing and/or switching transceiver building blocks in these handsets is mandatory in order to extend battery life and/or reduce cost. Only adaptive circuits that are able to reconfigure themselves within the handover time can meet the design requirements of a single receiver or transmitter covering all the different standards while ensuring seamless inter-interoperability. This paper presents analog and digital base-band circuits that are able to support GSM (with Edge), WCDMA (UMTS), WLAN and Bluetooth using reconfigurable building blocks. The blocks can trade off power consumption for performance on the fly, depending on the standard to be supported and the required QoS (Quality of Service) leve

Single pole switch leg based multi‐port converter with an energy storage

Peer Reviewedhttp://deepblue.lib.umich.edu/bitstream/2027.42/163829/1/pel2bf03233.pd