Energy-efficient wireline transceivers

Power-efficient wireline transceivers are highly demanded by many applications in high performance computation and communication systems. Apart from transferring a wide range of data rates to satisfy the interconnect bandwidth requirement, the transceivers have very tight power budget and are expected to be fully integrated. This thesis explores enabling techniques to implement such transceivers in both circuit and system levels. Specifically, three prototypes will be presented: (1) a 5Gb/s reference-less clock and data recovery circuit (CDR) using phase-rotating phase-locked loop (PRPLL) to conduct phase control so as to break several fundamental trade-offs in conventional receivers; (2) a 4-10.5Gb/s continuous-rate CDR with novel frequency acquisition scheme based on bang-bang phase detector (BBPD) and a ring oscillator-based fractional-N PLL as the low noise wide range DCO in the CDR loop; (3) a source-synchronous energy-proportional link with dynamic voltage and frequency scaling (DVFS) and rapid on/off (ROO) techniques to cut the link power wastage at system level. The receiver/transceiver architectures are highly digital and address the requirements of new receiver architecture development, wide operating range, and low power/area consumption while being fully integrated. Experimental results obtained from the prototypes attest the effectiveness of the proposed techniques

저 잡음 디지털 위상동기루프의 합성

학위논문 (박사)-- 서울대학교 대학원 : 전기·컴퓨터공학부, 2014. 2. 정덕균.As a device scaling proceeds, Charge Pump PLL has been confronted by many design challenges. Especially, a leakage current in loop filter and reduced dynamic range due to a lower operating voltage make it difficult to adopt a conventional analog PLL architecture for a highly scaled technology. To solve these issues, All Digital PLL (ADPLL) has been widely studied recently. ADPLL mitigates a filter leakage and a reduced dynamic range issues by replacing the analog circuits with digital ones. However, it is still difficult to get a low jitter under low supply voltage. In this thesis, we propose a dual loop architecture to achieve a low jitter even with a low supply voltage. And bottom-up based multi-step TDC and DCO are proposed to meet both fine resolution and wide operation range. In the aspect of design methodology, ADPLL has relied on a full custom design method although ADPLL is fully described in HDL (Hardware Description Language). We propose a new cell based layout technique to automatically synthesize the whole circuit and layout. The test chip has no linearity degradation although it is fully synthesized using a commercially available auto P&R tool. We has implemented an all digital pixel clock generator using the proposed dual loop architecture and the cell based layout technique. The entire circuit is automatically synthesized using 28nm CMOS technology. And s-domain linear model is utilized to optimize the jitter of the dual-loop PLL. Test chip occupies 0.032mm2, and achieves a 15ps_rms integrated jitter although it has extremely low input reference clock of 100 kHz. The whole circuit operates at 1.0V and consumes only 3.1mW.Abstract i Lists of Figures vii Lists of Tables xiii 1. Introduction 1 1.1 Thesis Motivation and Organization 1 1.1.1 Motivation 1 1.1.2 Thesis Organization 2 1.2 PLL Design Issues in Scaled CMOS Technology 3 1.2.1 Low Supply Voltage 4 1.2.2 High Leakage Current 6 1.2.3 Device Reliability: NBTI, HCI, TDDB, EM 8 1.2.4 Mismatch due to Proximity Effects: WPE, STI 11 1.3 Overview of Clock Synthesizers 14 1.3.1 Dual Voltage Charge Pump PLL 14 1.3.2 DLL Based Edge Combining Clock Multiplier 16 1.3.3 Recirculation DLL 17 1.3.4 Reference Injected PLL 18 1.3.5 All Digital PLL 19 1.3.6 Flying Adder Clock Synthesizer 20 1.3.7 Dual Loop Hybrid PLL 21 1.3.8 Comparisons 23 2. Tutorial of ADPLL Design 25 2.1 Introduction 25 2.1.1 Motivation for a pure digital 25 2.1.2 Conversion to digital domain 26 2.2 Functional Blocks 26 2.2.1 TDC, and PFD/Charge Pump 26 2.2.2 Digital Loop Filter and Analog R/C Loop Filter 29 2.2.3 DCO and VCO 34 2.2.4 S-domain Model of the Whole Loop 34 2.2.5 ADPLL Loop Design Flow 36 2.3 S-domain Noise Model 41 2.3.1 Noise Transfer Functions 41 2.3.2 Quantization Noise due to Limited TDC Resolution 45 2.3.3 Quantization Noise due to Divider ΔΣ Noise 46 2.3.4 Quantization Noise due to Limited DCO Resolution 47 2.3.5 Quantization Noise due to DCO ΔΣ Dithering 48 2.3.6 Random Noise of DCO and Input Clock 50 2.3.7 Over-all Phase Noise 50 3. Synthesizable All Digital Pixel Clock PLL Design 53 3.1 Overview 53 3.1.1 Introduction of Pixel Clock PLL 53 3.1.1 Design Specifications 55 3.2 Proposed Architecture 60 3.2.1 All Digital Dual Loop PLL 60 3.2.2 2-step controlled TDC 61 3.2.3 3-step controlled DCO 64 3.2.4 Digital Loop Filter 76 3.3 S-domain Noise Model 78 3.4 Loop Parameter Optimization Based on the s-domain Model 85 3.5 RTL and Gate Level Circuit Design 88 3.5.1 Overview of the design flow 88 3.5.2 Behavioral Simulation and Gate level synthesis 89 3.5.1 Preventing a meta-stability 90 3.5.1 Reusable Coding Style 92 3.6 Layout Synthesis 94 3.6.1 Auto P&R 94 3.6.2 Design of Unit Cells 97 3.6.3 Linearity Degradation in Synthesized TDC 98 3.6.4 Linearity Degradation in Synthesized DCO 106 3.7 Experiment Results 109 3.7.1 DCO measurement 109 3.7.2 PLL measurement 113 3.8 Conclusions 117 A. Device Technology Scaling Trends 118 A.1. Motivation for Technology Scaling 118 A.2. Constant Field Scaling 120 A.3. Quasi Constant Voltage Scaling 123 A.4. Device Technology Trends in Real World 124 B. Spice Simulation Tip for a DCO 137 C. Phase Noise to Jitter Conversion 141 Bibliography 144 초록 151Docto

고속 시리얼 링크를 위한 고리 발진기를 기반으로 하는 주파수 합성기

학위논문(박사) -- 서울대학교대학원 : 공과대학 전기·정보공학부, 2022. 8. 정덕균.In this dissertation, major concerns in the clocking of modern serial links are discussed. As sub-rate, multi-standard architectures are becoming predominant, the conventional clocking methodology seems to necessitate innovation in terms of low-cost implementation. Frequency synthesis with active, inductor-less oscillators replacing LC counterparts are reviewed, and solutions for two major drawbacks are proposed. Each solution is verified by prototype chip design, giving a possibility that the inductor-less oscillator may become a proper candidate for future high-speed serial links. To mitigate the high flicker noise of a high-frequency ring oscillator (RO), a reference multiplication technique that effectively extends the bandwidth of the following all-digital phase-locked loop (ADPLL) is proposed. The technique avoids any jitter accumulation, generating a clean mid-frequency clock, overall achieving high jitter performance in conjunction with the ADPLL. Timing constraint for the proper reference multiplication is first analyzed to determine the calibration points that may correct the existent phase errors. The weight for each calibration point is updated by the proposed a priori probability-based least-mean-square (LMS) algorithm. To minimize the time required for the calibration, each gain for the weight update is adaptively varied by deducing a posteriori which error source dominates the others. The prototype chip is fabricated in a 40-nm CMOS technology, and its measurement results verify the low-jitter, high-frequency clock generation with fast calibration settling. The presented work achieves an rms jitter of 177/223 fs at 8/16-GHz output, consuming 12.1/17-mW power. As the second embodiment, an RO-based ADPLL with an analog technique that addresses the high supply sensitivity of the RO is presented. Unlike prior arts, the circuit for the proposed technique does not extort the RO voltage headroom, allowing high-frequency oscillation. Further, the performance given from the technique is robust over process, voltage, and temperature (PVT) variations, avoiding the use of additional calibration hardware. Lastly, a comprehensive analysis of phase noise contribution is conducted for the overall ADPLL, followed by circuit optimizations, to retain the low-jitter output. Implemented in a 40-nm CMOS technology, the frequency synthesizer achieves an rms jitter of 289 fs at 8 GHz output without any injected supply noise. Under a 20-mVrms white supply noise, the ADPLL suppresses supply-noise-induced jitter by -23.8 dB.본 논문은 현대 시리얼 링크의 클락킹에 관여되는 주요한 문제들에 대하여 기술한다. 준속도, 다중 표준 구조들이 채택되고 있는 추세에 따라, 기존의 클라킹 방법은 낮은 비용의 구현의 관점에서 새로운 혁신을 필요로 한다. LC 공진기를 대신하여 능동 소자 발진기를 사용한 주파수 합성에 대하여 알아보고, 이에 발생하는 두가지 주요 문제점과 각각에 대한 해결 방안을 탐색한다. 각 제안 방법을 프로토타입 칩을 통해 그 효용성을 검증하고, 이어서 능동 소자 발진기가 미래의 고속 시리얼 링크의 클락킹에 사용될 가능성에 대해 검토한다. 첫번째 시연으로써, 고주파 고리 발진기의 높은 플리커 잡음을 완화시키기 위해 기준 신호를 배수화하여 뒷단의 위상 고정 루프의 대역폭을 효과적으로 극대화 시키는 회로 기술을 제안한다. 본 기술은 지터를 누적 시키지 않으며 따라서 깨끗한 중간 주파수 클락을 생성시켜 위상 고정 루프와 함께 높은 성능의 고주파 클락을 합성한다. 기준 신호를 성공적으로 배수화하기 위한 타이밍 조건들을 먼저 분석하여 타이밍 오류를 제거하기 위한 방법론을 파악한다. 각 교정 중량은 연역적 확률을 기반으로한 LMS 알고리즘을 통해 갱신되도록 설계된다. 교정에 필요한 시간을 최소화 하기 위하여, 각 교정 이득은 타이밍 오류 근원들의 크기를 귀납적으로 추론한 값을 바탕으로 지속적으로 제어된다. 40-nm CMOS 공정으로 구현된 프로토타입 칩의 측정을 통해 저소음, 고주파 클락을 빠른 교정 시간안에 합성해 냄을 확인하였다. 이는 177/223 fs의 rms 지터를 가지는 8/16 GHz의 클락을 출력한다. 두번째 시연으로써, 고리 발진기의 높은 전원 노이즈 의존성을 완화시키는 기술이 포함된 주파수 합성기가 설계되었다. 이는 고리 발진기의 전압 헤드룸을 보존함으로서 고주파 발진을 가능하게 한다. 나아가, 전원 노이즈 감소 성능은 공정, 전압, 온도 변동에 대하여 민감하지 않으며, 따라서 추가적인 교정 회로를 필요로 하지 않는다. 마지막으로, 위상 노이즈에 대한 포괄적 분석과 회로 최적화를 통하여 주파수 합성기의 저잡음 출력을 방해하지 않는 방법을 고안하였다. 해당 프로토타입 칩은 40-nm CMOS 공정으로 구현되었으며, 전원 노이즈가 인가되지 않은 상태에서 289 fs의 rms 지터를 가지는 8 GHz의 클락을 출력한다. 또한, 20 mVrms의 전원 노이즈가 인가되었을 때에 유도되는 지터의 양을 -23.8 dB 만큼 줄이는 것을 확인하였다.1 Introduction 1 1.1 Motivation 3 1.1.1 Clocking in High-Speed Serial Links 4 1.1.2 Multi-Phase, High-Frequency Clock Conversion 8 1.2 Dissertation Objectives 10 2 RO-Based High-Frequency Synthesis 12 2.1 Phase-Locked Loop Fundamentals 12 2.2 Toward All-Digital Regime 15 2.3 RO Design Challenges 21 2.3.1 Oscillator Phase Noise 21 2.3.2 Challenge 1: High Flicker Noise 23 2.3.3 Challenge 2: High Supply Noise Sensitivity 26 3 Filtering RO Noise 28 3.1 Introduction 28 3.2 Proposed Reference Octupler 34 3.2.1 Delay Constraint 34 3.2.2 Phase Error Calibration 38 3.2.3 Circuit Implementation 51 3.3 IL-ADPLL Implementation 55 3.4 Measurement Results 59 3.5 Summary 63 4 RO Supply Noise Compensation 69 4.1 Introduction 69 4.2 Proposed Analog Closed Loop for Supply Noise Compensation 72 4.2.1 Circuit Implementation 73 4.2.2 Frequency-Domain Analysis 76 4.2.3 Circuit Optimization 81 4.3 ADPLL Implementation 87 4.4 Measurement Results 90 4.5 Summary 98 5 Conclusions 99 A Notes on the 8REF 102 B Notes on the ACSC 105박

Digital enhancement techniques for fractional-N frequency synthesizers

Meeting the demand for unprecedented connectivity in the era of internet-of-things (IoT) requires extremely energy efficient operation of IoT nodes to extend battery life. Managing the data traffic generated by trillions of such nodes also puts severe energy constraints on the data centers. Clock generators that are essential elements in these systems consume significant power and therefore must be optimized for low power and high performance. The focus of this thesis is on improving the energy efficiency of frequency synthesizers and clocking modules by exploring design techniques at both the architectural and circuit levels. In the first part of this work, a digital fractional-N phase locked loop (FNPLL) that employs a high resolution time-to-digital converter (TDC) and a truly ΔΣ fractional divider to achieve low in-band noise with a wide bandwidth is presented. The fractional divider employs a digital-to-time converter (DTC) to cancel out ΔΣ quantization noise in time domain, thus alleviating TDC dynamic range requirements. The proposed digital architecture adopts a narrow range low-power time-amplifier based TDC (TA-TDC) to achieve sub 1ps resolution. Fabricated in 65nm CMOS process, the prototype PLL achieves better than -106dBc/Hz in-band noise and 3MHz PLL bandwidth at 4.5GHz output frequency using 50MHz reference. The PLL achieves excellent jitter performance of 490fsrms, while consumes only 3.7mW. This translates to the best reported jitter-power figure-of-merit (FoM) of -240.5dB among previously reported FNPLLs. Phase noise performance of ring oscillator based digital FNPLLs is severely compromised by conflicting bandwidth requirements to simultaneously suppress oscillator phase and quantization noise introduced by the TDC, ΔΣ fractional divider, and digital-to-analog converter (DAC). As a consequence, their FoM that quantifies the power-jitter tradeoff is at least 25dB worse than their LC-oscillator based FNPLL counterparts. In the second part of this thesis, we seek to close this performance gap by extending PLL bandwidth using quantization noise cancellation techniques and by employing a dual-path digital loop filter to suppress the detrimental impact of DAC quantization noise. A prototype was implemented in a 65nm CMOS process operating over a wide frequency range of 2.0GHz-5.5GHz using a modified extended range multi-modulus divider with seamless switching. The proposed digital FNPLL achieves 1.9psrms integrated jitter while consuming only 4mW at 5GHz output. The measured in-band phase noise is better than -96 dBc/Hz at 1MHz offset. The proposed FNPLL achieves wide bandwidth up to 6MHz using a 50 MHz reference and its FoM is -228.5dB, which is at about 20dB better than previously reported ring-based digital FNPLLs. In the third part, we propose a new multi-output clock generator architecture using open loop fractional dividers for system-on-chip (SoC) platforms. Modern multi-core processors use per core clocking, where each core runs at its own speed. The core frequency can be changed dynamically to optimize for performance or power dissipation using a dynamic frequency scaling (DFS) technique. Fast frequency switching is highly desirable as long as it does not interrupt code execution; therefore it requires smooth frequency transitions with no undershoots. The second main requirement in processor clocking is the capability of spread spectrum frequency modulation. By spreading the clock energy across a wide bandwidth, the electromagnetic interference (EMI) is dramatically reduced. A conventional PLL clock generation approach suffers from a slow frequency settling and limited spread spectrum modulation capabilities. The proposed open loop fractional divider architecture overcomes the bandwidth limitation in fractional-N PLLs. The fractional divider switches the output frequency instantaneously and provides an excellent spread spectrum performance, where precise and programmable modulation depth and frequency can be applied to satisfy different EMI requirements. The fractional divider has unlimited modulation bandwidth resulting in spread spectrum modulation with no filtering, unlike fractional-N PLL; consequently it achieves higher EMI reduction. A prototype fractional divider was implemented in a 65nm CMOS process, where the measured peak-to-peak jitter is less than 27ps over a wide frequency range from 20MHz to 1GHz. The total power consumption is about 3.2mW for 1GHz output frequency. The all-digital implementation of the divider occupies the smallest area of 0.017mm2 compared to state-of-the-art designs. As the data rate of serial links goes higher, the jitter requirements of the clock generator become more stringent. Improving the jitter performance of conventional PLLs to less than (200fsrms) always comes with a large power penalty (tens of mWs). This is due to the PLL coupled noise bandwidth trade-off, which imposes stringent noise requirements on the oscillator and/or loop components. Alternatively, an injection-locked clock multiplier (ILCM) provides many advantages in terms of phase noise, power, and area compared to classical PLLs, but they suffer from a narrow lock-in range and a high sensitivity to PVT variations especially at a large multiplication factor (N). In the fourth part of this thesis, a low-jitter, low-power LC-based ILCM with a digital frequency-tracking loop (FTL) is presented. The proposed FTL relies on a new pulse gating technique to continuously tune the oscillator's free-running frequency. The FTL ensures robust operation across PVT variations and resolves the race condition existing in injection locked PLLs by decoupling frequency tuning from the injection path. As a result, the phase locking condition is only determined by the injection path. This work also introduces an accurate theoretical large-signal analysis for phase domain response (PDR) of injection locked oscillators (ILOs). The proposed PDR analysis captures the asymmetric nature of ILO's lock-in range, and the impact of frequency error on injection strength and phase noise performance. The proposed architecture and analysis are demonstrated by a prototype fabricated in 65 nm CMOS process with active area of 0.25mm2. The prototype ILCM multiplies the reference frequency by 64 to generate an output clock in the range of 6.75GHz-8.25GHz. A superior jitter performance of 190fsrms is achieved, while consuming only 2.25mW power. This translates to a best FoM of -251dB. Unlike conventional PLLs, ILCMs have been fundamentally limited to only integer-N operation and cannot synthesize fractional-N frequencies. In the last part of this thesis, we extend the merits of ILCMs to fractional-N and overcome this fundamental limitation. We employ DTC-based QNC techniques in order to align injected pulses to the oscillator's zero crossings, which enables it to pull the oscillator toward phase lock, thus realizing a fractional-N ILCM. Fabricated in 65nm CMOS process, a prototype 20-bit fractional-N ILCM with an output range of 6.75GHz-8.25GHz consumes only 3.25mW. It achieves excellent jitter performance of 110fsrms and 175fsrms in integer- and fractional-N modes respectively, which translates to the best-reported FoM in both integer- (-255dB) and fractional-N (-252dB) modes. The proposed fractional-N ILCM also features the first-reported rapid on/off capability, where the transient absolute jitter performance at wake-up is bounded below 4ps after less than 4ns. This demonstrates almost instantaneous phase settling. This unique capability enables tremendous energy saving by turning on the clock multiplier only when needed. This energy proportional operation leverages idle times to save power at the system-level of wireline and wireless transceivers

A Bang-Bang All-Digital PLL for Frequency Synthesis

abstract: Phase locked loops are an integral part of any electronic system that requires a clock signal and find use in a broad range of applications such as clock and data recovery circuits for high speed serial I/O and frequency synthesizers for RF transceivers and ADCs. Traditionally, PLLs have been primarily analog in nature and since the development of the charge pump PLL, they have almost exclusively been analog. Recently, however, much research has been focused on ADPLLs because of their scalability, flexibility and higher noise immunity. This research investigates some of the latest all-digital PLL architectures and discusses the qualities and tradeoffs of each. A highly flexible and scalable all-digital PLL based frequency synthesizer is implemented in 180 nm CMOS process. This implementation makes use of a binary phase detector, also commonly called a bang-bang phase detector, which has potential of use in high-speed, sub-micron processes due to the simplicity of the phase detector which can be implemented with a simple D flip flop. Due to the nonlinearity introduced by the phase detector, there are certain performance limitations. This architecture incorporates a separate frequency control loop which can alleviate some of these limitations, such as lock range and acquisition time.Dissertation/ThesisM.S. Electrical Engineering 201

High Performance Local Oscillator Design for Next Generation Wireless Communication

Local Oscillator (LO) is an essential building block in modern wireless radios. In modern wireless radios, LO often serves as a reference of the carrier signal to modulate or demod- ulate the outgoing or incoming data. The LO signal should be a clean and stable source, such that the frequency or timing information of the carrier reference can be well-defined. However, as radio architecture evolves, the importance of LO path design has become much more important than before. Of late, many radio architecture innovations have exploited sophisticated LO generation schemes to meet the ever-increasing demands of wireless radio performances. The focus of this thesis is to address challenges in the LO path design for next-generation high performance wireless radios. These challenges include (1) Congested spectrum at low radio frequency (RF) below 5GHz (2) Continuing miniaturization of integrated wireless radio, and (3) Fiber-fast (>10Gb/s) mm-wave wireless communication. The thesis begins with a brief introduction of the aforementioned challenges followed by a discussion of the opportunities projected to overcome these challenges. To address the challenge of congested spectrum at frequency below 5GHz, novel ra- dio architectures such as cognitive radio, software-defined radio, and full-duplex radio have drawn significant research interest. Cognitive radio is a radio architecture that opportunisti- cally utilize the unused spectrum in an environment to maximize spectrum usage efficiency. Energy-efficient spectrum sensing is the key to implementing cognitive radio. To enable energy-efficient spectrum sensing, a fast-hopping frequency synthesizer is an essential build- ing block to swiftly sweep the carrier frequency of the radio across the available spectrum. Chapter 2 of this thesis further highlights the challenges and trade-offs of the current LO gen- eration scheme for possible use in sweeping LO-based spectrum analysis. It follows by intro- duction of the proposed fast-hopping LO architecture, its implementation and measurement results of the validated prototype. Chapter 3 proposes an embedded phase-shifting LO-path design for wideband RF self-interference cancellation for full-duplex radio. It demonstrates a synergistic design between the LO path and signal to perform self-interference cancellation. To address the challenge of continuing miniaturization of integrated wireless radio, ring oscillator-based frequency synthesizer is an attractive candidate due to its compactness. Chapter 4 discussed the difficulty associated with implementing a Phase-Locked Loop (PLL) with ultra-small form-factor. It further proposes the concept sub-sampling PLL with time- based loop filter to address these challenges. A 65nm CMOS prototype and its measurement result are presented for validation of the concept. In shifting from RF to mm-wave frequencies, the performance of wireless communication links is boosted by significant bandwidth and data-rate expansion. However, the demand for data-rate improvement is out-pacing the innovation of radio architectures. A >10Gb/s mm-wave wireless communication at 60GHz is required by emerging applications such as virtual-reality (VR) headsets, inter-rack data transmission at data center, and Ultra-High- Definition (UHD) TV home entertainment systems. Channel-bonding is considered to be a promising technique for achieving >10Gb/s wireless communication at 60GHz. Chapter 5 discusses the fundamental radio implementation challenges associated with channel-bonding for 60GHz wireless communication and the pros and cons of prior arts that attempted to address these challenges. It is followed by a discussion of the proposed 60GHz channel- bonding receiver, which utilizes only a single PLL and enables both contiguous and non- contiguous channel-bonding schemes. Finally, Chapter 6 presents the conclusion of this thesis

Design of energy efficient high speed I/O interfaces

Energy efficiency has become a key performance metric for wireline high speed I/O interfaces. Consequently, design of low power I/O interfaces has garnered large interest that has mostly been focused on active power reduction techniques at peak data rate. In practice, most systems exhibit a wide range of data transfer patterns. As a result, low energy per bit operation at peak data rate does not necessarily translate to overall low energy operation. Therefore, I/O interfaces that can scale their power consumption with data rate requirement are desirable. Rapid on-off I/O interfaces have a potential to scale power with data rate requirements without severely affecting either latency or the throughput of the I/O interface. In this work, we explore circuit techniques for designing rapid on-off high speed wireline I/O interfaces and digital fractional-N PLLs. A burst-mode transmitter suitable for rapid on-off I/O interfaces is presented that achieves 6 ns turn-on time by utilizing a fast frequency settling ring oscillator in digital multiplying delay-locked loop and a rapid on-off biasing scheme for current mode output driver. Fabricated in 90 nm CMOS process, the prototype achieves 2.29 mW/Gb/s energy efficiency at peak data rate of 8 Gb/s. A 125X (8 Gb/s to 64 Mb/s) change in effective data rate results in 67X (18.29 mW to 0.27 mW) change in transmitter power consumption corresponding to only 2X (2.29 mW/Gb/s to 4.24 mW/Gb/s) degradation in energy efficiency for 32-byte long data bursts. We also present an analytical bit error rate (BER) computation technique for this transmitter under rapid on-off operation, which uses MDLL settling measurement data in conjunction with always-on transmitter measurements. This technique indicates that the BER bathtub width for 10^(−12) BER is 0.65 UI and 0.72 UI during rapid on-off operation and always-on operation, respectively. Next, a pulse response estimation-based technique is proposed enabling burst-mode operation for baud-rate sampling receivers that operate over high loss channels. Such receivers typically employ discrete time equalization to combat inter-symbol interference. Implementation details are provided for a receiver chip, fabricated in 65nm CMOS technology, that demonstrates efficacy of the proposed technique. A low complexity pulse response estimation technique is also presented for low power receivers that do not employ discrete time equalizers. We also present techniques for implementation of highly digital fractional-N PLL employing a phase interpolator based fractional divider to improve the quantization noise shaping properties of a 1-bit ∆Σ frequency-to-digital converter. Fabricated in 65nm CMOS process, the prototype calibration-free fractional-N Type-II PLL employs the proposed frequency-to-digital converter in place of a high resolution time-to-digital converter and achieves 848 fs rms integrated jitter (1 kHz-30 MHz) and -101 dBc/Hz in-band phase noise while generating 5.054 GHz output from 31.25 MHz input

An Analog Multiphase Self-Calibrating DLL to Minimize the Effects of Process, Supply Voltage, and Temperature Variations

Delay locked loops have been found to be useful tools in such applications as computing, TDCs, and communications. These system can be found in space exploration vehicles and satellites, which operate in extreme environments. Unfortunately, in these environments supply voltage and temperature will not be constant, therefore they must be under consideration when designing a DLL. Furthermore, solar radiation in conjunction with the varying environmental aspects, could cause the delay locked loop to lose it locked state. Delay locked loops are inherently good at tracking these environmental aspects, but in order to do so, the voltage controlled delay line must exhibit a very large gain, which translates to a large capture range. Assuming charged particles hit a key node in the DLL (e.g. the control voltage), the DLL would lose lock and would have to recapture it. Depending on the severity of the uctuation, this relocking process could easily take on the order of many microseconds assuming the bandwidth was kept low to minimize jitter. To date, no delay locked loops have been published for extreme environment applications. In many other extreme environment circuits, calibration techniques have been applied to minimize the environmental effects. Whereas there have been multiple calibration methods published related to delay locked loops, none of them were intended for extreme environments. Furthermore, none of these methods are directly suitable for an analog multiphase delay locked loop. The self-calibrating DLL in this work includes an all digital calibration circuit, as well as a system transient monitor. The coarse calibration helps minimize global process, voltage, and temperature errors for an analog multiphase DLL. The system monitor is used to detect any transients that might cause the DLL to unlock, which could be used to allow the DLL to be recalibrated to the new environmental conditions. The presented measurement results will demonstrate that the DLL can be used in extreme environments such as space, or other extreme environment applications

Digital Intensive Mixed Signal Circuits with In-situ Performance Monitors

University of Minnesota Ph.D. dissertation.November 2016. Major: Electrical/Computer Engineering. Advisor: Chris Kim. 1 computer file (PDF); x, 137 pages.Digital intensive circuit design techniques of different mixed-signal systems such as data converters, clock generators, voltage regulators etc. are gaining attention for the implementation of modern microprocessors and system-on-chips (SoCs) in order to fully utilize the benefits of CMOS technology scaling. Moreover different performance improvement schemes, for example, noise reduction, spur cancellation, linearity improvement etc. can be easily performed in digital domain. In addition to that, increasing speed and complexity of modern SoCs necessitate the requirement of in-situ measurement schemes, primarily for high volume testing. In-situ measurements not only obviate the need for expensive measurement equipments and probing techniques, but also reduce the test time significantly when a large number of chips are required to be tested. Several digital intensive circuit design techniques are proposed in this dissertation along with different in-situ performance monitors for a variety of mixed signal systems. First, a novel beat frequency quantization technique is proposed in a two-step VCO quantizer based ADC implementation for direct digital conversion of low amplitude bio- potential signals. By direct conversion, it alleviates the requirement of the area and power consuming analog-frontend (AFE) used in a conventional ADC designs. This prototype design is realized in a 65nm CMOS technology. Measured SNDR is 44.5dB from a 10mVpp, 300Hz signal and power consumption is only 38μW. Next, three different clock generation circuits, a phase-locked loop (PLL), a multiplying delay-locked loop (MDLL) and a frequency-locked loop (FLL) are presented. First a 0.4-to-1.6GHz sub-sampling fractional-N all digital PLL architecture is discussed that utilizes a D-flip-flop as a digital sub-sampler. Measurement results from a 65nm CMOS test-chip shows 5dB lower phase noise at 100KHz offset frequency, compared to a conventional architecture. The Digital PLL (DPLL) architecture is further extended for a digital MDLL implementation in order to suppress the VCO phase noise beyond the DPLL bandwidth. A zero-offset aperture phase detector (APD) and a digital- to-time converter (DTC) are employed for static phase-offset (SPO) cancellation. A unique in-situ detection circuitry achieves a high resolution SPO measurement in time domain. A 65nm test-chip shows 0.2-to-1.45GHz output frequency range while reducing the phase-noise by 9dB compared to a DPLL. Next, a frequency-to-current converter (FTC) based fractional FLL is proposed for a low accuracy clock generation in an extremely low area for IoT application. High density deep-trench capacitors are used for area reduction. The test-chip is fabricated in a 32nm SOI technology that takes only 0.0054mm2 active area. A high-resolution in-situ period jitter measurement block is also incorporated in this design. Finally, a time based digital low dropout (DLDO) regulator architecture is proposed for fine grain power delivery over a wide load current dynamic range and input/output voltage in order to facilitate dynamic voltage and frequency scaling (DVFS). High- resolution beat frequency detector dynamically adjusts the loop sampling frequency for ripple and settling time reduction due to load transients. A fixed steady-state voltage offset provides inherent active voltage positioning (AVP) for ripple reduction. Circuit simulations in a 65nm technology show more than 90% current efficiency for 100X load current variation, while it can operate for an input voltage range of 0.6V – 1.2V

Toward realizing power scalable and energy proportional high-speed wireline links

Growing computational demand and proliferation of cloud computing has placed high-speed serial links at the center stage. Due to saturating energy efficiency improvements over the last five years, increasing the data throughput comes at the cost of power consumption. Conventionally, serial link power can be reduced by optimizing individual building blocks such as output drivers, receiver, or clock generation and distribution. However, this approach yields very limited efficiency improvement. This dissertation takes an alternative approach toward reducing the serial link power. Instead of optimizing the power of individual building blocks, power of the entire serial link is reduced by exploiting serial link usage by the applications. It has been demonstrated that serial links in servers are underutilized. On average, they are used only 15% of the time, i.e. these links are idle for approximately 85% of the time. Conventional links consume power during idle periods to maintain synchronization between the transmitter and the receiver. However, by powering-off the link when idle and powering it back when needed, power consumption of the serial link can be scaled proportionally to its utilization. This approach of rapid power state transitioning is known as the rapid-on/off approach. For the rapid-on/off to be effective, ideally the power-on time, off-state power, and power state transition energy must all be close to zero. However, in practice, it is very difficult to achieve these ideal conditions. Work presented in this dissertation addresses these challenges. When this research work was started (2011-12), there were only a couple of research papers available in the area of rapid-on/off links. Systematic study or design of a rapid power state transitioning in serial links was not available in the literature. Since rapid-on/off with nanoseconds granularity is not a standard in any wireline communication, even the popular test equipment does not support testing any such feature, neither any formal measurement methodology was available. All these circumstances made the beginning difficult. However, these challenges provided a unique opportunity to explore new architectural techniques and identify trade-offs. The key contributions of this dissertation are as follows. The first and foremost contribution is understanding the underlying limitations of saturating energy efficiency improvements in serial links and why there is a compelling need to find alternative ways to reduce the serial link power. The second contribution is to identify potential power saving techniques and evaluate the challenges they pose and the opportunities they present. The third contribution is the design of a 5Gb/s transmitter with a rapid-on/off feature. The transmitter achieves rapid-on/off capability in voltage mode output driver by using a fast-digital regulator, and in the clock multiplier by accurate frequency pre-setting and periodic reference insertion. To ease timing requirements, an improved edge replacement logic circuit for the clock multiplier is proposed. Mathematical modeling of power-on time as a function of various circuit parameters is also discussed. The proposed transmitter demonstrates energy proportional operation over wide variations of link utilization, and is, therefore, suitable for energy efficient links. Fabricated in 90nm CMOS technology, the voltage mode driver, and the clock multiplier achieve power-on-time of only 2ns and 10ns, respectively. This dissertation highlights key trade-off in the clock multiplier architecture, to achieve fast power-on-lock capability at the cost of jitter performance. The fourth contribution is the design of a 7GHz rapid-on/off LC-PLL based clock multi- plier. The phase locked loop (PLL) based multiplier was developed to overcome the limita- tions of the MDLL based approach. Proposed temperature compensated LC-PLL achieves power-on-lock in 1ns. The fifth and biggest contribution of this dissertation is the design of a 7Gb/s embedded clock transceiver, which achieves rapid-on/off capability in LC-PLL, current-mode transmit- ter and receiver. It was the first reported design of a complete transceiver, with an embedded clock architecture, having rapid-on/off capability. Background phase calibration technique in PLL and CDR phase calibration logic in the receiver enable instantaneous lock on power-on. The proposed transceiver demonstrates power scalability with a wide range of link utiliza- tion and, therefore, helps in improving overall system efficiency. Fabricated in 65nm CMOS technology, the 7Gb/s transceiver achieves power-on-lock in less than 20ns. The transceiver achieves power scaling by 44x (63.7mW-to-1.43mW) and energy efficiency degradation by only 2.2x (9.1pJ/bit-to-20.5pJ/bit), when the effective data rate (link utilization) changes by 100x (7Gb/s-to-70Mb/s). The sixth and final contribution is the design of a temperature sensor to compensate the frequency drifts due to temperature variations, during long power-off periods, in the fast power-on-lock LC-PLL. The proposed self-referenced VCO-based temperature sensor is designed with all digital logic gates and achieves low supply sensitivity. This sensor is suitable for integration in processor and DRAM environments. The proposed sensor works on the principle of directly converting temperature information to frequency and finally to digital bits. A novel sensing technique is proposed in which temperature information is acquired by creating a threshold voltage difference between the transistors used in the oscillators. Reduced supply sensitivity is achieved by employing junction capacitance, and the overhead of voltage regulators and an external ideal reference frequency is avoided. The effect of VCO phase noise on the sensor resolution is mathematically evaluated. Fabricated in the 65nm CMOS process, the prototype can operate with a supply ranging from 0.85V to 1.1V, and it achieves a supply sensitivity of 0.034oC/mV and an inaccuracy of ±0.9oC and ±2.3oC from 0-100oC after 2-point calibration, with and without static nonlinearity correction, respectively. It achieves a resolution of 0.3oC, resolution FoM of 0.3(nJ/conv)res2 , and measurement (conversion) time of 6.5μs