Ultra-Low Power and Radiation Hardened Asynchronous Circuit Design

This dissertation proposes an ultra-low power design methodology called bit-wise MTNCL for bit-wise pipelined asynchronous circuits, which combines multi-threshold CMOS (MTCMOS) with bit-wise pipelined NULL Convention Logic (NCL) systems. It provides the leakage power advantages of an all high-Vt implementation with a reasonable speed penalty compared to the all low-Vt implementation, and has negligible area overhead. It was enhanced to handle indeterminate standby states. The original MTNCL concept was enhanced significantly by sleeping Registers and Completion Logic as well as Combinational circuits to reduce area, leakage power, and energy per operation. This dissertation also develops an architecture that allows NCL circuits to recover from a Single Event Upset (SEU) or Single Event Latchup (SEL) fault without any data loss. Finally, an accurate throughput derivation formula for pipelined NCL circuits was developed, which can be used for static timing analysis

Comparing energy and latency of asynchronous and synchronous NoCs for embedded SoCs

Journal ArticlePower consumption of on-chip interconnects is a primary concern for many embedded system-on-chip (SoC) applications. In this paper, we compare energy and performance characteristics of asynchronous (clockless) and synchronous network on-chip implementations, optimized for a number of SoC designs. We adapted the COSI-2.0 framework with ORION 2.0 router and wire models for synchronous network generation. Our own tool, ANetGen, specifies the asynchronous network by determining the topology with simulated-annealing and router locations with force-directed placement. It uses energy and delay models from our 65 nm bundled-data router design. SystemC simulations varied traffic burstiness using the self-similar b-model. Results show that the asynchronous network provided lower median and maximum message latency, especially under bursty traffic, and used far less router energy with a slight overhead for the interrouter wires

Spatial parallelism in the routers of asynchronous on-chip networks

State-of-the-art multi-processor systems-on-chip use on-chip networks as their communication fabric. Although most on-chip networks are implemented synchronously, asynchronous on-chip networks have several advantages over their synchronous counterparts. Timing division multiplexing (TDM) flow control methods have been utilized in asynchronous on-chip networks extensively. The synchronization required by TDM leads to significant speed penalties. Compared with using TDM methods, spatial parallelism methods, such as the spatial division multiplexing (SDM) flow control method, achieve better network throughput with less area overhead.This thesis proposes several techniques to increase spatial parallelism in the routers of asynchronous on-chip networks.Channel slicing is a new pipeline structure that alleviates the speed penalty by removing the synchronization among bit-level data pipelines. It is also found out that the lookahead pipeline using early evaluated acknowledgement can be used in routers to further improve speed.SDM is a new flow control method proposed for asynchronous on-chip networks. It improves network throughput without introducing synchronization among buffers of different frames, which is required by TDM methods. It is also found that the area overhead of SDM is smaller than the virtual channel (VC) flow control method -- the most used TDM method. The major design problem of SDM is the area consuming crossbars. A novel 2-stage Clos switch structure is proposed to replace the crossbar in SDM routers, which significantly reduces the area overhead. This Clos switch is dynamically reconfigured by a new asynchronous Clos scheduler.Several asynchronous SDM routers are implemented using these new techniques. An asynchronous VC router is also reproduced for comparison. Performance analyses show that the SDM routers outperform the VC router in throughput, area overhead and energy efficiency.EThOS - Electronic Theses Online ServiceGBUnited Kingdo

Spatial parallelism in the routers of asynchronous on-chip networks

State-of-the-art multi-processor systems-on-chip use on-chip networks as their communication fabric. Although most on-chip networks are implemented synchronously, asynchronous on-chip networks have several advantages over their synchronous counterparts. Timing division multiplexing (TDM) flow control methods have been utilized in asynchronous on-chip networks extensively. The synchronization required by TDM leads to significant speed penalties. Compared with using TDM methods, spatial parallelism methods, such as the spatial division multiplexing (SDM) flow control method, achieve better network throughput with less area overhead.This thesis proposes several techniques to increase spatial parallelism in the routers of asynchronous on-chip networks.Channel slicing is a new pipeline structure that alleviates the speed penalty by removing the synchronization among bit-level data pipelines. It is also found out that the lookahead pipeline using early evaluated acknowledgement can be used in routers to further improve speed.SDM is a new flow control method proposed for asynchronous on-chip networks. It improves network throughput without introducing synchronization among buffers of different frames, which is required by TDM methods. It is also found that the area overhead of SDM is smaller than the virtual channel (VC) flow control method -- the most used TDM method. The major design problem of SDM is the area consuming crossbars. A novel 2-stage Clos switch structure is proposed to replace the crossbar in SDM routers, which significantly reduces the area overhead. This Clos switch is dynamically reconfigured by a new asynchronous Clos scheduler.Several asynchronous SDM routers are implemented using these new techniques. An asynchronous VC router is also reproduced for comparison. Performance analyses show that the SDM routers outperform the VC router in throughput, area overhead and energy efficiency.EThOS - Electronic Theses Online ServiceGBUnited Kingdo

Master of Science

thesisIntegrated circuits often consist of multiple processing elements that are regularly tiled across the two-dimensional surface of a die. This work presents the design and integration of high speed relative timed routers for asynchronous network-on-chip. It researches NoC's efficiency through simplicity by directly translating simple T-router, source-routing, single-flit packet to higher radix routers. This work is intended to study performance and power trade-offs adding higher radix routers, 3D topologies, Virtual Channels, Accurate NoC modeling, and Transmission line communication links. Routers with and without virtual channels are designed and integrated to arrayed communication networks. Furthermore, the work investigates 3D networks with diffusive RC wires and transmission lines on long wrap interconnects

Doctor of Philosophy

dissertationPortable electronic devices will be limited to available energy of existing battery chemistries for the foreseeable future. However, system-on-chips (SoCs) used in these devices are under a demand to offer more functionality and increased battery life. A difficult problem in SoC design is providing energy-efficient communication between its components while maintaining the required performance. This dissertation introduces a novel energy-efficient network-on-chip (NoC) communication architecture. A NoC is used within complex SoCs due it its superior performance, energy usage, modularity, and scalability over traditional bus and point-to-point methods of connecting SoC components. This is the first academic research that combines asynchronous NoC circuits, a focus on energy-efficient design, and a software framework to customize a NoC for a particular SoC. Its key contribution is demonstrating that a simple, asynchronous NoC concept is a good match for low-power devices, and is a fruitful area for additional investigation. The proposed NoC is energy-efficient in several ways: simple switch and arbitration logic, low port radix, latch-based router buffering, a topology with the minimum number of 3-port routers, and the asynchronous advantages of zero dynamic power consumption while idle and the lack of a clock tree. The tool framework developed for this work uses novel methods to optimize the topology and router oorplan based on simulated annealing and force-directed movement. It studies link pipelining techniques that yield improved throughput in an energy-efficient manner. A simulator is automatically generated for each customized NoC, and its traffic generators use a self-similar message distribution, as opposed to Poisson, to better match application behavior. Compared to a conventional synchronous NoC, this design is superior by achieving comparable message latency with half the energy

Custom Cell Placement Automation for Asynchronous VLSI

Asynchronous Very-Large-Scale-Integration (VLSI) integrated circuits have demonstrated many advantages over their synchronous counterparts, including low power consumption, elastic pipelining, robustness against manufacturing and temperature variations, etc. However, the lack of dedicated electronic design automation (EDA) tools, especially physical layout automation tools, largely limits the adoption of asynchronous circuits. Existing commercial placement tools are optimized for synchronous circuits, and require a standard cell library provided by semiconductor foundries to complete the physical design. The physical layouts of cells in this library have the same height to simplify the placement problem and the power distribution network. Although the standard cell methodology also works for asynchronous designs, the performance is inferior compared with counterparts designed using the full-custom design methodology. To tackle this challenge, we propose a gridded cell layout methodology for asynchronous circuits, in which the cell height and cell width can be any integer multiple of two grid values. The gridded cell approach combines the shape regularity of standard cells with the size flexibility of full-custom layouts. Therefore, this approach can achieve a better space utilization ratio and lower wire length for asynchronous designs. Experiments have shown that the gridded cell placement approach reduces area without impacting the routability. We have also used this placer to tape out a chip in a 65nm process technology, demonstrating that our placer generates design-rule clean results

Asynchronous techniques for new generation variation-tolerant FPGA

PhD ThesisThis thesis presents a practical scenario for asynchronous logic implementation that would benefit the modern Field-Programmable Gate Arrays (FPGAs) technology in improving reliability. A method based on Asynchronously-Assisted Logic (AAL) blocks is proposed here in order to provide the right degree of variation tolerance, preserve as much of the traditional FPGAs structure as possible, and make use of asynchrony only when necessary or beneficial for functionality. The newly proposed AAL introduces extra underlying hard-blocks that support asynchronous interaction only when needed and at minimum overhead. This has the potential to avoid the obstacles to the progress of asynchronous designs, particularly in terms of area and power overheads. The proposed approach provides a solution that is complementary to existing variation tolerance techniques such as the late-binding technique, but improves the reliability of the system as well as reducing the design’s margin headroom when implemented on programmable logic devices (PLDs) or FPGAs. The proposed method suggests the deployment of configurable AAL blocks to reinforce only the variation-critical paths (VCPs) with the help of variation maps, rather than re-mapping and re-routing. The layout level results for this method's worst case increase in the CLB’s overall size only of 6.3%. The proposed strategy retains the structure of the global interconnect resources that occupy the lion’s share of the modern FPGA’s soft fabric, and yet permits the dual-rail iv completion-detection (DR-CD) protocol without the need to globally double the interconnect resources. Simulation results of global and interconnect voltage variations demonstrate the robustness of the method