High Performance Power Management Integrated Circuits for Portable Devices

abstract: Portable devices often require multiple power management IC (PMIC) to power different sub-modules, Li-ion batteries are well suited for portable devices because of its small size, high energy density and long life cycle. Since Li-ion battery is the major power source for portable device, fast and high-efficiency battery charging solution has become a major requirement in portable device application. In the first part of dissertation, a high performance Li-ion switching battery charger is proposed. Cascaded two loop (CTL) control architecture is used for seamless CC-CV transition, time based technique is utilized to minimize controller area and power consumption. Time domain controller is implemented by using voltage controlled oscillator (VCO) and voltage controlled delay line (VCDL). Several efficiency improvement techniques such as segmented power-FET, quasi-zero voltage switching (QZVS) and switching frequency reduction are proposed. The proposed switching battery charger is able to provide maximum 2 A charging current and has an peak efficiency of 93.3%. By configure the charger as boost converter, the charger is able to provide maximum 1.5 A charging current while achieving 96.3% peak efficiency. The second part of dissertation presents a digital low dropout regulator (DLDO) for system on a chip (SoC) in portable devices application. The proposed DLDO achieve fast transient settling time, lower undershoot/overshoot and higher PSR performance compared to state of the art. By having a good PSR performance, the proposed DLDO is able to power mixed signal load. To achieve a fast load transient response, a load transient detector (LTD) enables boost mode operation of the digital PI controller. The boost mode operation achieves sub microsecond settling time, and reduces the settling time by 50% to 250 ns, undershoot/overshoot by 35% to 250 mV and 17% to 125 mV without compromising the system stability.Dissertation/ThesisDoctoral Dissertation Electrical Engineering 201

A Highly Digital VCO-Based ADC With Lookup-Table-Based Background Calibration

CMOS technology scaling has enabled dramatic improvement for digital circuits both in terms of speed and power efficiency. However, most traditional analog-to-digital converter (ADC) architectures are challenged by ever-decreasing supply voltage. The improvement in time resolution enabled by increased digital speeds drives design towards time-domain architectures such as voltage-controlled-oscillator (VCO) based ADCs. The main challenge in VCO-based ADC design is mitigating the nonlinearity of VCO Voltage-to-frequency (V-to-f) characteristics. Achieving signal-to-noise ratio (SNR) performance better than 40dB requires some form of calibration, which can be realized by analog or digital techniques, or some combination. This dissertation proposes a highly digital, reconfigurable VCO-based ADC with lookup-table (LUT) based background calibration based on split ADC architecture. Each of the two split channels, ADC A and B , contains two VCOs in a differential configuration. This helps alleviate even-order distortions as well as increase the dynamic range. A digital controller on chip can reconfigure the ADCs\u27 sampling rates and resolutions to adapt to various application scenarios. Different types of input signals can be used to train the ADC’s LUT parameters through the simple, anti-aliasing continuous-time input to achieve target resolution. The chip is fabricated in a 180 nm CMOS process, and the active area of analog and digital circuits is 0.09 and 0.16mm^2, respectively. Power consumption of the core ADC function is 25 mW. Measured results for this prototype design with 12-b resolution show ENOB improves from uncorrected 5-b to 11.5-b with calibration time within 200 ms (780K conversions at 5 MSps sample rate)

A Ringamp-Assisted, Output Capacitor-less Analog CMOS Low-Dropout Voltage Regulator

Continued advancements in state-of-the-art integrated circuits have furthered trends toward higher computational performance and increased functionality within smaller circuit area footprints, all while improving power efficiencies to meet the demands of mobile and battery-powered applications. A significant portion of these advancements have been enabled by continued scaling of CMOS technology into smaller process node sizes, facilitating faster digital systems and power optimized computation. However, this scaling has degraded classic analog amplifying circuit structures with reduced voltage headroom and lower device output resistance; and thus, lower available intrinsic gain. This work investigates these trends and their impact for fine-grain Low-Dropout (LDO) Voltage Regulators, leading to a presented design methodology and implementation of a state-of-the-art Ringamp-Assisted, Output Capacitor-less Analog CMOS LDO Voltage Regulator capable of both power scaling and process node scaling for general SoC applications

Design, analysis and implementation of voltage sensor for power-constrained systems

PhD ThesisThanks to an extensive effort by the global research community, the electronic technology has significantly matured over the last decade. This technology has enabled certain operations which humans could not otherwise easily perform. For instance, electronic systems can be used to perform sensing, monitoring and even control operations in environments such as outer space, underground, under the sea or even inside the human body. The main difficulty for electronics operating in these environments is access to a reliable and permanent source of energy. Using batteries as the immediate solution for this problem has helped to provide energy for limited periods of time; however, regular maintenance and replacement are required. Consequently, battery solutions fail wherever replacing them is not possible or operation for long periods is needed. For such cases, researchers have proposed harvesting ambient energy and converting it into an electrical form. An important issue with energy harvesters is that their operation and output power depend critically on the amount of energy they receive and because ambient energy often tends to be sporadic in nature, energy harvesters cannot produce stable or fixed levels of power all of the time. Therefore, electronic devices powered in this way must be capable of adapting their operation to the energy status of the harvester. To achieve this, information on the energy available for use is needed. This can be provided by a sensor capable of measuring voltage. However, stable and fixed voltage and time references are a prerequisite of most traditional voltage measurement devices, but these generally do not exist in energy harvesting environments. A further challenge is that such a sensor also needs to be powered by the energy harvester’s unstable voltage. In this thesis, the design of a reference-free voltage sensor, which can operate with a varying voltage source, is provided based on the capture of a portion of the total energy which is directly related to II the energy being sensed. This energy is then used to power a computation which quantifies captured energy over time, with the information directly generated as digital code. The sensor was fabricated in the 180 nm technology node and successfully tested by performing voltage measurements over the range 1.8 V to 0.8 V

Design of Readout Electronics for the DEEP Particle Detector

Along with electromagnetic radiation, the Sun also emits a constant stream of charged particles in the form of solar wind. When these particles enter Earth’s atmosphere through a process known as particle precipitation, they can through a series of chemical reactions produce N Ox and HOx gases. These gases are greenhouse gases and deplete the ozone in the mesosphere and upper stratosphere. It is important to quantify the rate of production of these gases to model the potential climate impact. Existing particle detectors in space are suboptimal because they cannot determine the energy flux and pitch angle distribution of precipitating particles. The primary scientific objective of the DEEP project is to design a particle detector instrument that is specifically designed for particle precipitation measurements. This thesis investigates different data acquisition schemes for handling the signal from a pixel detector. The chosen approach is measuring the width of a shaped pulse to quantify the energy of the particle. Known as Time-over-Threshold, a detector circuit board is designed featuring high-speed comparators as threshold discriminators and the NG-MEDIUM FPGA from NanoXplore to implement the data acquisition. Digitizing the comparator pulse width is done with a Time-to-Digital converter (TDC) implemented in the FPGA fabric. Since the difference in pulse width is small for different energies, a high conversion resolution is required. Two high-resolution TDCs are designed and compared, both of which feature a digital counter and a method of interpolating the counter clock period. The first interpolation method applies the use of a multitapped delay line implemented with hard carry chain resources, and the second method oversamples the input with several equally off-phase sampling clocks. A resolution of 302 ps and a differential non-linearity of 3.26 was achieved with the delay line TDC clocked at 100 MHz. An automatic statistical calibration scheme is included to determine the actual delays of the delay line, utilizing a second asynchronous clock to generate uniformly distributed hits. The asynchronous oversampler resolution is clock frequency dependent and provides a 4-fold improvement to the clock period. The differential nonlinearity approaches zero with close matching of the off-phase clocks and operating frequency. A complete firmware design for the data acquisition and rocket telemetry of the detector is proposed and demonstrated. A simulation of the firmware utilizing each TDC topology is conducted and the delay line TDC is demonstrated to be the most accurate at all operating frequencies and thus the recommended TDC for the DEEP data acquisition.Masteroppgave i fysikkPHYS399MAMN-PHY

DIGITALLY ASSISTED TECHNIQUES FOR NYQUIST RATE ANALOG-to-DIGITAL CONVERTERS

With the advance of technology and rapid growth of digital systems, low power high speed analog-to-digital converters with great accuracy are in demand. To achieve high effective number of bits Analog-to-Digital Converter(ADC) calibration as a time consuming process is a potential bottleneck for designs. This dissertation presentsa fully digital background calibration algorithm for a 7-bit redundant flash ADC using split structure and look-up table based correction. Redundant comparators are used in the flash ADC design of this work in order to tolerate large offset voltages while minimizing signal input capacitance. The split ADC structure helps by eliminating the unknown input signal from the calibration path. The flash ADC has been designed in 180nm IBM CMOS technology and fabricated through MOSIS. This work was supported by Analog Devices, Wilmington,MA. While much research on ADC design has concentrated on increasing resolution and sample rate, there are many applications (e.g. biomedical devices and sensor networks) that do not require high performance but do require low power energy efficient ADCs. This dissertation also explores on design of a low quiescent current 100kSps Successive Approximation (SAR) ADC that has been used as an error detection ADC for an automotive application in 350nm CD (CMOS-DMOS) technology. This work was supported by ON Semiconductor Corp, East Greenwich,RI

Digital ADCs and ultra-wideband RF circuits for energy constrained wireless applications by Denis Clarke Daly.

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2009.Cataloged from PDF version of thesis.Includes bibliographical references (p. 173-183).Ongoing advances in semiconductor technology have enabled a multitude of portable, low power devices like cellular phones and wireless sensors. Most recently, as transistor device geometries reach the nanometer scale, transistor characteristics have changed so dramatically that many traditional circuits and architectures are no longer optimal and/or feasible. As a solution, much research has focused on developing 'highly digital' circuits and architectures that are tolerant of the increased leakage, variation and degraded voltage headrooms associated with advanced CMOS processes. This thesis presents several highly digital, mixed-signal circuits and architectures designed for energy constrained wireless applications. First, as a case study, a highly digital, voltage scalable flash ADC is presented. The flash ADC, implemented in 0.18 [mu]m CMOS, leverages redundancy and calibration to achieve robust operation at supply voltages from 0.2 V to 0.9 V. Next, the thesis expands in scope to describe a pulsed, noncoherent ultra-wideband transceiver chipset, implemented in 90 nm CMOS and operating in the 3-to-5 GHz band. The all-digital transmitter employs capacitive combining and pulse shaping in the power amplifier to meet the FCC spectral mask without any off-chip filters. The noncoherent receiver system-on-chip achieves both energy efficiency and high performance by employing simple amplifier and ADC structures combined with extensive digital calibration. Finally, the transceiver chipset is integrated in a complete system for wireless insect flight control.(cont.) Through the use of a flexible PCB and 3D die stacking, the total weight of the electronics is kept to 1 g, within the carrying capacity of an adult Manduca sexta moth. Preliminary wireless flight control of a moth in a wind tunnel is demonstrated.Ph.D

High-Speed Delta-Sigma Data Converters for Next-Generation Wireless Communication

In recent years, Continuous-time Delta-Sigma(CT-ΔΣ) analog-to-digital converters (ADCs) have been extensively investigated for their use in wireless receivers to achieve conversion bandwidths greater than 15 MHz and higher resolution of 10 to 14 bits. This dissertation investigates the current state-of-the-art high-speed single-bit and multi-bit Continuous-time Delta-Sigma modulator (CT-ΔΣM) designs and their limitations due to circuit non-idealities in achieving the performance required for next-generation wireless standards. Also, we presented complete architectural and circuit details of a high-speed single-bit and multi-bit CT-ΔΣM operating at a sampling rate of 1.25 GSps and 640 MSps respectively (the highest reported sampling rate in a 0.13 μm CMOS technology node) with measurement results. Further, we propose novel hybrid ΔΣ architecture with two-step quantizer to alleviate the bandwidth and resolution bottlenecks associated with the contemporary CT-ΔΣM topologies. To facilitate the design with the proposed architecture, a robust systematic design method is introduced to determine the loop-filter coefficients by taking into account the non-ideal integrator response, such as the finite opamp gain and the presence of multiple parasitic poles and zeros. Further, comprehensive system-level simulation is presented to analyze the effect of two-step quantizer non-idealities such as the offset and gain error in the sub-ADCs, and the current mismatch between the MSB and LSB elements in the feedback DAC. The proposed novel architecture is demonstrated by designing a high-speed wideband 4th order CT-ΔΣ modulator prototype, employing a two-step quantizer with 5-bits resolution. The proposed modulator takes advantage of the combination of a high-resolution two-step quantization technique and an excess-loop delay (ELD) compensation of more than one clock cycle to achieve lower-power consumption (28 mW), higher dynamic range (\u3e69 dB) with a wide conversion bandwidth (20 MHz), even at a lower sampling rate of 400 MHz. The proposed modulator achieves a Figure of Merit (FoM) of 340 fJ/level

Cost effective technology applied to domotics and smart home energy management systems

Premio extraordinario de Trabajo Fin de Máster curso 2019/2020. Máster en Energías Renovables DistribuidasIn this document is presented the state of art for domotics cost effective technologies available on market nowadays, and how to apply them in Smart Home Energy Management Systems (SHEMS) allowing peaks shaving, renewable management and home appliance controls, always in cost effective context in order to be massively applied. Additionally, beyond of SHEMS context, it will be also analysed how to apply this technology in order to increase homes energy efficiency and monitoring of home appliances. Energy management is one of the milestones for distributed renewable energy spread; since renewable energy sources are not time-schedulable, are required control systems capable of the management for exchanging energy between conventional sources (power grid), renewable sources and energy storage sources. With the proposed approach, there is a first block dedicated to show an overview of Smart Home Energy Management Systems (SMHEMS) classical architecture and functional modules of SHEMS; next step is to analyse principles which has allowed some devices to become a cost-effective technology. Once the technology has been analysed, it will be reviewed some specific resources (hardware and software) available on marked for allowing low cost SHEMS. Knowing the “tools” available; it will be shown how to adapt classical SHEMS to cost effective technology. Such way, this document will show some specific applications of SHEMS. Firstly, in a general point of view, comparing the proposed low-cost technology with one of the main existing commercial proposals; and secondly, developing the solution for a specific real case.En este documento se aborda el estado actual de la domótica de bajo coste disponible en el mercado actualmente y cómo aplicarlo en los sistemas inteligentes de gestión energética en la vivienda (SHEMS) permitiendo el recorte de las puntas de demanda, gestión de energías renovables y control de electrodomésticos, siempre en el contexto del bajo coste, con el objetivo de lograr la máxima difusión de los SHEMS. Adicionalmente, más allá del contexto de la tecnología SHEMS, se analizará cómo aplicar esta tecnología para aumentar la eficiencia energética de los hogares y para la supervisión de los electrodomésticos. La gestión energética es uno de los factores principales para lograr la difusión de las energías renovables distribuidas; debido a que las fuentes de energía renovable no pueden ser planificadas, se requieren sistemas de control capaces de gestionar el intercambio de energía entre las fuentes convencionales (red eléctrica de distribución), energías renovables y dispositivos de almacenamiento energético. Bajo esta perspectiva, este documento presenta un primer bloque en el que se exponen las bases de la arquitectura y módulos funcionales de los sistemas inteligentes de gestión energética en la vivienda (SHEMS); el siguiente paso será analizar los principios que han permitido a ciertos dispositivos convertirse en dispositivos de bajo coste. Una vez analizada la tecnología, nos centraremos en los recursos (hardware y software) existentes que permitirán la realización de un SHEMS a bajo coste. Conocidas las “herramientas” a nuestra disposición, se mostrará como adaptar un esquema SHEMS clásico a la tecnología de bajo coste. Primeramente, comparando de modo genérico la tecnología de bajo coste con una de las principales propuestas comerciales de SHEMS, para seguidamente desarrollar la solución de bajo coste a un caso específico real