Handover management in mobile WiMAX using adaptive cross-layer technique

The protocol type and the base station (BS) technology are the main communication media between the Vehicle to Infrastructure (V2I) communication in vehicular networks. During high speed vehicle movement, the best communication would be with a seamless handover (HO) delay in terms of lower packet loss and throughput. Many studies have focused on how to reduce the HO delay during lower speeds of the vehicle with data link (L2) and network (L3) layers protocol. However, this research studied the Transport Layer (L4) protocol mobile Stream Control Transmission Protocol (mSCTP) used as an optimal protocol in collaboration with the Location Manager (LM) and Domain Name Server (DNS). In addition, the BS technology that performs smooth HO employing an adaptive algorithm in L2 to perform the HO according to current vehicle speed was also included in the research. The methods derived from the combination of L4 and the BS technology methods produced an Adaptive Cross-Layer (ACL) design which is a mobility oriented handover management scheme that adapts the HO procedure among the protocol layers. The optimization has a better performance during HO as it is reduces scanning delay and diversity level as well as support transparent mobility among layers in terms of low packet loss and higher throughput. All of these metrics are capable of offering maximum flexibility and efficiency while allowing applications to refine the behaviour of the HO procedure. Besides that, evaluations were performed in various scenarios including different vehicle speeds and background traffic. The performance evaluation of the proposed ACL had approximately 30% improvement making it better than the other handover solutions

Efficient Micro-Mobility using Intra-domain Multicast-based Mechanisms (M&M)

One of the most important metrics in the design of IP mobility protocols is the handover performance. The current Mobile IP (MIP) standard has been shown to exhibit poor handover performance. Most other work attempts to modify MIP to slightly improve its efficiency, while others propose complex techniques to replace MIP. Rather than taking these approaches, we instead propose a new architecture for providing efficient and smooth handover, while being able to co-exist and inter-operate with other technologies. Specifically, we propose an intra-domain multicast-based mobility architecture, where a visiting mobile is assigned a multicast address to use while moving within a domain. Efficient handover is achieved using standard multicast join/prune mechanisms. Two approaches are proposed and contrasted. The first introduces the concept proxy-based mobility, while the other uses algorithmic mapping to obtain the multicast address of visiting mobiles. We show that the algorithmic mapping approach has several advantages over the proxy approach, and provide mechanisms to support it. Network simulation (using NS-2) is used to evaluate our scheme and compare it to other routing-based micro-mobility schemes - CIP and HAWAII. The proactive handover results show that both M&M and CIP shows low handoff delay and packet reordering depth as compared to HAWAII. The reason for M&M's comparable performance with CIP is that both use bi-cast in proactive handover. The M&M, however, handles multiple border routers in a domain, where CIP fails. We also provide a handover algorithm leveraging the proactive path setup capability of M&M, which is expected to outperform CIP in case of reactive handover.Comment: 12 pages, 11 figure

A network mobility management architecture for a heteregeneous network environment

Network mobility management enables mobility of personal area networks and vehicular networks across heterogeneous access networks using a Mobile Router. This dissertation presents a network mobility management architecture for minimizing the impact of handoffs on the communications of nodes in the mobile network. The architecture addresses mobility in legacy networks without infrastructure support, but can also exploit infrastructure support for improved handoff performance. Further, the proposed architecture increases the efficiency of communications of nodes in the mobile network with counter parts in the fixed network through the use of caching and route optimization. The performance and costs of the proposed architecture are evaluated through empirical and numerical analysis. The analysis shows the feasibility of the architecture in the networks of today and in those of the near future.Verkkojen liikkuuvudenhallinta mahdollistaa henkilökohtaisten ja ajoneuvoihin asennettujen verkkojen liikkuvuuden heterogeenisessä verkkoympäristössä käyttäen liikkuvaa reititintä. Tämä väitöskirja esittää uuden arkkitehtuurin verkkojen liikkuvuudenhallintaan, joka minimoi verkonvaihdon vaikutuksen päätelaitteiden yhteyksiin. Vanhoissa verkoissa, joiden infrastruktuuri ei tue verkkojen liikkuvuutta, verkonvaihdos täytyy hallita liikkuvassa reitittimessa. Standardoitu verkkojen liikkuvuudenhallintaprotokolla NEMO mahdollistaa tämän käyttäen ankkurisolmua kiinteässä verkossa pakettien toimittamiseen päätelaitteiden kommunikaatiokumppaneilta liikkuvalle reitittimelle. NEMO:ssa verkonvaihdos aiheuttaa käynnissä olevien yhteyksien keskeytymisen yli sekunnin mittaiseksi ajaksi, aiheuttaen merkittävää häiriötä viestintäsovelluksille. Esitetyssä arkkitehtuurissa verkonvaihdon vaikutus minimoidaan varustamalla liikkuva reititin kahdella radiolla. Käyttäen kahta radiota liikkuva reititin pystyy suorittamaan verkonvaihdon keskeyttämättä päätelaitteiden yhteyksiä, mikäli verkonvaihtoon on riittävästi aikaa. Käytettävissa oleva aika riippuu liikkuvan reitittimen nopeudesta ja radioverkon rakenteesta. Arkkitehtuuri osaa myös hyödyntää infrastruktuurin tukea saumattomaan verkonvaihtoon. Verkkoinfrastruktuurin tuki nopeuttaa verkonvaihdosprosessia, kasvattaenmaksimaalista verkonvaihdos tahtia. Tällöin liikkuva reitin voi käyttää lyhyen kantaman radioverkkoja, joiden solun säde on yli 80m, ajonopeuksilla 90m/s asti ilman, että verkonvaihdos keskeyttää päätelaitteiden yhteyksiä. Lisäksi ehdotettu arkkitehtuuri tehostaa kommunikaatiota käyttäen cache-palvelimia liikkuvassa ja kiinteässä verkossa ja optimoitua reititystä liikkuvien päätelaitteiden ja kiinteässä verkossa olevien kommunikaatiosolmujen välillä. Cache-palvelinarkkitehtuuri hyödyntää vapaita radioresursseja liikkuvan verkon cache-palvelimen välimuistin päivittämiseen. Heterogeenisessä verkkoympäristossä cache-palvelimen päivitys suoritetaan lyhyen kantaman laajakaistaisia radioverkkoja käyttäen. Liikkuvan reitittimen siirtyessä laajakaistaisen radioverkon peitealueen ulkopuolelle päätelaitteille palvellaan sisältöä, kuten www sivuja tai videota cache-palvelimelta, säästäen laajemman kantaman radioverkon rajoitetumpia resursseja. Arkkitehtuurissa käytetään optimoitua reititystä päätelaitteiden ja niiden kommunikaatiokumppaneiden välillä. Optimoitu reititysmekanismi vähentää liikkuvuudenhallintaan käytettyjen protokollien langattoman verkon resurssien kulutusta. Lisäksi optimoitu reititysmekanismi tehostaa pakettien reititystä käyttäen suorinta reittiä kommunikaatiosolmujen välillä. Esitetyn arkkitehtuurin suorituskyky arvioidaan empiirisen ja numeerisen analyysin avulla. Analyysi arvioi arkkitehtuurin suorituskykyä ja vertaa sitä aikaisemmin ehdotettuihin ratkaisuihin ja osoittaa arkkitehtuurin soveltuvan nykyisiin ja lähitulevaisuuden langattomiin verkkoihin.reviewe

A survey on subjecting electronic product code and non-ID objects to IP identification

Over the last decade, both research on the Internet of Things (IoT) and real-world IoT applications have grown exponentially. The IoT provides us with smarter cities, intelligent homes, and generally more comfortable lives. However, the introduction of these devices has led to several new challenges that must be addressed. One of the critical challenges facing interacting with IoT devices is to address billions of devices (things) around the world, including computers, tablets, smartphones, wearable devices, sensors, and embedded computers, and so on. This article provides a survey on subjecting Electronic Product Code and non-ID objects to IP identification for IoT devices, including their advantages and disadvantages thereof. Different metrics are here proposed and used for evaluating these methods. In particular, the main methods are evaluated in terms of their: (i) computational overhead, (ii) scalability, (iii) adaptability, (iv) implementation cost, and (v) whether applicable to already ID-based objects and presented in tabular format. Finally, the article proves that this field of research will still be ongoing, but any new technique must favorably offer the mentioned five evaluative parameters.Comment: 112 references, 8 figures, 6 tables, Journal of Engineering Reports, Wiley, 2020 (Open Access

Design of multi-homing architecture for mobile hosts

This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.This thesis proposes a new multi-homing mobile architecture for future heterogeneous network environment. First, a new multi-homed mobile architecture called Multi Network Switching enabled Mobile IPv6 (MNS-MIP6) is proposed which enables a Mobile Node (MN) having multiple communication paths between itself and its Correspondent Node (CN) to take full advantage of being multi-homed. Multiple communication paths exist because MN, CN, or both are simultaneously attached to multiple access networks. A new sub layer is introduced within IP layer of the host’s protocol stack. A context is established between the MN and the CN. Through this context, additional IP addresses are exchanged between the two. Our MNS-MIP6 architecture allows one communication to smoothly switch from one interface/communication path to another. This switch remains transparent to other layers above IP. Second, to make communication more reliable in multi-homed mobile environments, a new failure detection and recovery mechanism called Mobile Reach ability Protocol (M-REAP) is designed within the proposed MNS-MIP6 architecture. The analysis shows that our new mechanism makes communication more reliable than the existing failure detection and recovery procedures in multi-homed mobile environments. Third, a new network selection mechanism is introduced in the proposed architecture which enables a multi-homed MN to choose the network best suited for particular application traffic. A Policy Engine is defined which takes parameters from iv the available networks, compares them according to application profiles and user preferences, and chooses the best network. The results show that in multi-homed mobile environment, load can be shared among different networks/interfaces through our proposed load sharing mechanism. Fourth, a seamless handover procedure is introduced in the system which enables multi-homed MN to seamlessly roam in a heterogeneous network environment. Layer 2 triggers are defined which assist in handover process. When Signal to Noise Ratio (SNR) on a currently used active interface becomes low, a switch is made to a different active interface. We show through mathematical and simulation analysis that our proposed scheme outperforms the existing popular handover management enhancement scheme in MIPv6 networks namely Fast Handover for MIPv6 (FMIPv6). Finally, a mechanism is introduced to allow legacy hosts to communicate with MNS-MIP6 MNs and gain the benefits of reliability, load sharing and seamless handover. The mechanism involves introducing middle boxes in CN’s network. These boxes are called Proxy-MNS boxes. Context is established between the middle boxes and a multi-homed MN

Future Trends and Challenges for Mobile and Convergent Networks

Some traffic characteristics like real-time, location-based, and community-inspired, as well as the exponential increase on the data traffic in mobile networks, are challenging the academia and standardization communities to manage these networks in completely novel and intelligent ways, otherwise, current network infrastructures can not offer a connection service with an acceptable quality for both emergent traffic demand and application requisites. In this way, a very relevant research problem that needs to be addressed is how a heterogeneous wireless access infrastructure should be controlled to offer a network access with a proper level of quality for diverse flows ending at multi-mode devices in mobile scenarios. The current chapter reviews recent research and standardization work developed under the most used wireless access technologies and mobile access proposals. It comprehensively outlines the impact on the deployment of those technologies in future networking environments, not only on the network performance but also in how the most important requirements of several relevant players, such as, content providers, network operators, and users/terminals can be addressed. Finally, the chapter concludes referring the most notable aspects in how the environment of future networks are expected to evolve like technology convergence, service convergence, terminal convergence, market convergence, environmental awareness, energy-efficiency, self-organized and intelligent infrastructure, as well as the most important functional requisites to be addressed through that infrastructure such as flow mobility, data offloading, load balancing and vertical multihoming.Comment: In book 4G & Beyond: The Convergence of Networks, Devices and Services, Nova Science Publishers, 201

A Multi-Hop 6LoWPAN Wireless Sensor Network for Waste Management Optimization

In the first part of this Thesis several Wireless Sensor Network technologies, including the ones based on the IEEE 802.15.4 Protocol Standard like ZigBee, 6LoWPAN and Ultra Wide Band, as well as other technologies based on other protocol standards like Z-Wave, Bluetooth and Dash7, are analyzed with respect to relevance and suitability with the Waste Management Outsmart European FP7 Project. A particular attention is given to the parameters which characterize a Large Scale WSN for Smart Cities, due to the amount of sensors involved and to the practical application requested by the project. Secondly, a prototype of sensor network is proposed: an Operative System named Contiki is chosen for its portability on different hardware platforms, its Open Source license, for the use of the 6LoW-PAN protocol and for the implementation of the new RPL routing protocol. The Operative System is described in detail, with a special focus on the uIPv6 TCP/IP stack and RPL implementation. With regard to this innovative routing proto col designed specifically for Low Power Lossy Networks, chapter 4 describes in detail how the network topology is organized as a Directed Acyclic Graph, what is an RPL Instance and how downward and upward routes are constructed and maintained. With the use of several AVR Atmel modules mounting the Contiki OS a real WSN is created and, with an Ultrasonic Sensor, the filling level of a waste basket prototype is periodically detected and transmitted through a multi-hop wireless network to a sink nodeope

Mobility in IPv6

Masteroppgave i informasjons- og kommunikasjonsteknologi 2001 - Høgskolen i Agder, GrimstadIn the future it is expectable that the number of terminals with wireless access to network resources will be more and more widespread, and it is therefore necessary to integrate mobility support into future generation networks so that users can be online, even while in motion. The increasing use of Internet suggests that the Internet technology can be the best candidate for effective realization of future generation mobile systems. Mobile IP can offer the possibility for use of the mobile Internet in other ways than it is used in the standard wired environment, and may be the solution to increasing mobility demands. Due to this, mobility in IPv6 (MIPv6) is designed to be scalable, stable, efficient and secure, which are the factors considered important for this thesis. Scalable – The number of users are expected to be so many that MIPv6 is, according to its specification, designed to scale almost as well as Internet without mobility support integrated. This implies the elimination of triangle routing, currently a challenge in MIPv4, and also a reasonable amount of data that must be managed by the nodes involved in mobility. MIPv6 is also designed so that future extensions and modifications are possible by allowing further growth. Stable – For the adoption rate of this technology to high, the users must be able to depend on the services provided. At present the implementations shows that there are still a few more steps to take until necessary stability is offered, but product quality releases of MIPv6 is expected to be released sometime next year. The implementation tested in this thesis reflects transparent mobility as to simple higher-level applications such as telnet and http, but not real-time applications. The implementation described in this thesis had some initial problems with the procedures for Duplicate Address Detection (DAD), which shall guarantee that all addresses on any given IPv6 network is unique. Some improvements for DAD have therefore been proposed in order to get better solutions as to fault-handling procedures when DAD fails. Efficient – Base MIPv6 as used in our implementation does not provide the handover efficiency needed for all kinds of applications. Seen from a traditional Internet point of view, the services offered are of best effort quality. A future version of the Internet protocol must, however, be designed to support applications with greater demands to handover latencies, than what a best effort service level can provide. Thus, the handover latency must in these cases be so small that it goes within the boundaries for e.g. demanding real-time applications. Several solutions are proposed for this purpose, but the area of research is still very new and no proposal will be defined for still some time. It seems like the initial mobility deployment phase will be without support for these services, but the technology is very promising and will most likely be integrated as the use of MIPv6 advances. Secure – In a large mobile environment mobile nodes will not only require Internet access within their own domain. They will also probably visit foreign networks, and as known from GSM infrastructure today, this will not be free of charge. Service providers in foreign domains commonly require authorization to ensure a good business relationship with the client. This leads directly to authentication, and of course accounting (AAA). This AAA infrastructure should be in place before mobile Internet can be deployed worldwide

Wireless Multi Hop Access Networks and Protocols

As more and more applications and services in our society now depend on the Internet, it is important that dynamically deployed wireless multi hop networks are able to gain access to the Internet and other infrastructure networks and services. This thesis proposes and evaluates solutions for providing multi hop Internet Access. It investigates how ad hoc networks can be combined with wireless and mesh networks in order to create wireless multi hop access networks. When several access points to the Internet are available, and the mobile node roams to a new access point, the node has to make a decision when and how to change its point of attachment. The thesis describes how to consider the rapid fluctuations of the wireless medium, how to handle the fact that other nodes on the path to the access point are also mobile which results in frequent link and route breaks, and the impact the change of attachment has on already existing connections. Medium access and routing protocols have been developed that consider both the long term and the short term variations of a mobile wireless network. The long term variations consider the fact that as nodes are mobile, links will frequently break and new links appear and thus the network topology map is constantly redrawn. The short term variations consider the rapid fluctuations of the wireless channel caused by mobility and multi path propagation deviations. In order to achieve diversity forwarding, protocols are presented which consider the network topology and the state of the wireless channel when decisions about forwarding need to be made. The medium access protocols are able to perform multi dimensional fast link adaptation on a per packet level with forwarding considerations. This i ncludes power, rate, code and channel adaptation. This will enable the type of performance improvements that are of significant importance for the success of multi hop wireless networks