An Ultra Low Power Digital to Analog Converter Optimized for Small Format LCD Applications

Liquid crystal displays (LCDs) for mobile applications present a unique design challenge. These small format displays can be found primarily in cell phones and PDAs which are devices that have particularly stringent power requirements. At the same time, the displays are increasing in resolution with every generation. This is creating demand for new LCD display technologies. The predominant amorphous thin film transistor technology is no longer feasible in the new high resolution small format screens due to the fact that the displays require too many connections to the driver and the aperture ratios do not allow high density displays. New technologies such as low temperature polysilicon (LTPS) displays continue to shrink in size and increase in resolution. LTPS technology enables the display manufacturer to create relatively high quality transistors on the glass. This allows for a display architecture which integrates the gate driver on the glass. Newer LTPS LCDs also enable a high level of multiplexing the sources lines on the glass which allows for a much simpler connection to the display driver chip. The electronic drivers for these display applications must adhere to strict power and area budgets. This work describes a low-power, area efficient, scalable, digital-to-analog conversion (DAC) integrated circuit architecture optimized for driving small format LCDs. The display driver is based on a twelve channel, 9-bit DAC driver. This architecture, suitable for % VGA resolution displays, exhibited a 2 MSPS conversion rate, less than 300 pW power dissipation per channel using a 5 V supply, and a die area of 0.042 mm per DAC. A new performance standard is set for DAC display drivers in joules per bit areal density

Performance enhancement in the desing of amplifier and amplifier-less circuits in modern CMOS technologies.

In the context of nowadays CMOS technology downscaling and the increasing demand of high performance electronics by industry and consumers, analog design has become a major challenge. On the one hand, beyond others, amplifiers have traditionally been a key cell for many analog systems whose overall performance strongly depends on those of the amplifier. Consequently, still today, achieving high performance amplifiers is essential. On the other hand, due to the increasing difficulty in achieving high performance amplifiers in downscaled modern technologies, a different research line that replaces the amplifier by other more easily achievable cells appears: the so called amplifier-less techniques. This thesis explores and contributes to both philosophies. Specifically, a lowvoltage differential input pair is proposed, with which three multistage amplifiers in the state of art are designed, analysed and tested. Moreover, a structure for the implementation of differential switched capacitor circuits, specially suitable for comparator-based circuits, that features lower distortion and less noise than the classical differential structures is proposed, an, as a proof of concept, implemented in a ΔΣ modulator

Pseudo-three-stage Miller op-amp with enhanced small-signal and large-signal performance

A simple technique to implement highly power efficient class AB-AB Miller op-amps is presented in this paper. It uses a composite input stage with resistive local common mode feedback that provides class AB operation to the input stage and essentially enhances the op-amp's effective transconductance gain, the dc open-loop gain, the gain-bandwidth product, and slew rate with just moderate increase in power dissipation. The experimental results of op-amps in strong inversion and subthreshold fabricated in a 130-nm standard CMOS technology validate the proposed approach. The op-amp has 9 V·pF/μs·μW large-signal figure of merit (FOM) and 17 MHz · pF/μW small-signal FOM with 1.2-V supply voltage. In subthreshold, the op-amp has 10 V · pF/μs · μW large-signal FOM and 92 MHz · pF/μW small-signal FOM with 0.5-V supply voltage.This work was supported by Grant TEC2016-80396- C2-R (AEI/FEDER)

Exploiting the bulk-driven approach in CMOS analogue amplifier design

This thesis presents a collection of new novel techniques using the bulk-driven approach, which can lead to performance enhancement in the field of CMOS analogue amplifier design under the very low-supply voltage constraints. In this thesis, three application areas of the bulk-driven approach are focused – at the input-stage of differential pairs, at the source followers, and at the cascode devices. For the input stage of differential pairs, this thesis proposes two new novel circuit design techniques. One of them utilises the concept of the replica-biased scheme in order to solve the non-linearity and latch-up issues, which are the potential problems that come along with the bulk-driven approach. The other proposed circuit design technique utilises the flipped voltage scheme and the Quasi-Floating Gate technique in order to achieve low-power high-speed performances, and furthermore the reversed-biased diode concept to overcome the issue of degraded input impedance characteristics that come along with the bulk-driven approach. Applying the bulk-driven approach in source followers is a new type of circuit blocks in CMOS analogue field, in which to the author’s best knowledge has not been proposed at any literatures in the past. This thesis presents the bulk-driven version of the flipped voltage followers and super source followers, which can lead to eliminating the DC level shift. Furthermore, a technique for programming the DC level shift less than the threshold voltage of a MOSFET, which cannot be achieved by conventional types of source followers, is presented. The effectiveness of the cascode device using the bulk-driven approach is validated by implementing it in a complete schematics design of a fully differential bulk-driven operational transcoductance amplifier (OTA). This proposal leads to solving the lowtranconductance problem of a bulk-driven differential pair, and in effect the open loop gain of the OTA exceeds 60dB using a 0.35μm CMOS technology. The final part of this thesis provides the study result of the input capacitance of a bulk-driven buffer. To verify the use of the BSIM3 MOSFET model in the simulation for predicting the input capacitance, the measurement data of the fabricated device are compared with the postlayout simulation results