Integrated circuits for efficient power delivery using pulse-width-modulation

Circuits and architectures for efficient power delivery have become crucial in emerging smart systems. Switching power amplifiers (PA) are very attractive for such applications, because they exhibit better efficiency compared to linear PA designs, due to saturated operation. Switching PAs also allow for utilization of deep submicron CMOS technologies, due to which these designs can be easily integrated with digital circuits, and can benefit from process scaling, in performance as well as in area. Pulse-width-modulation (PWM) is commonly used with switching PAs. A PWM signal typically employs a high-frequency switching pulse waveform as a carrier signal, wherein the pulse-width or duty-cycle of each pulse is modulated by a given low-frequency input signal. The carrier frequency can vary from several kHz to GHz, and is typically determined by the target application. In this thesis, efficient power-delivery circuits that use PWM with switching class-D stages are presented. Advanced circuit techniques, as well as architectures for PWM are proposed to enhance efficiency and circumvent the limitations of conventional architectures. A digitally-intensive transmitter using RF-PWM with a class-D PA is described in the first part of the thesis. The use of carrier switching for alleviating the dynamic range limitation that can be observed in classical RF-PWM implementations is introduced. The approach employs the full carrier frequency for half of the amplitude range, and the second harmonic of half of the carrier frequency, for the remainder of the amplitude range. This concept not only allows the transmitter to drive modulated signals with large peak-to-average power ratio (PAPR), but also improves the back-off efficiency due to reduced switching losses in the half carrier-frequency mode. A glitch-free phase selector is proposed that removes the deleterious glitches that can occur at the input data transitions. The phase-selector also prevents D flip-flop setup-and-hold time violations. The transmitter has been implemented in a 130-nm CMOS process. The measured peak output power and power-added-efficiency (PAE) are 25.6 dBm and 34%, respectively. While driving 802.11g 20-MHz 64-QAM OFDM signals, the average measured output power is 18.3 dBm and the PAE is 16%, with an EVM of -25.5 dB. The second part of the thesis describes a high-speed driver that provides a PWM output using a class-D PA. A PLL-based architecture is employed which eliminates the requirement for a precise ramp or triangular signal generator, and a high-speed comparator, which are typically used for PWM generation. Multi-level signaling is proposed to enhance back-off as well as peak efficiency, which is critical for signals with high PAPR. A differential, folded PWM scheme is introduced to achieve highly linear operation. 3-level operation is achieved without the requirement for additional supply source or sink paths, while 5-level operation is achieved with additional supply source and sink paths, compared to 2-level operation. The PWM driver has been implemented in a 130-nm CMOS process and can operate with a switching frequency of 40-to-170 MHz. For 2/3/5-level PA operation, with a 500 kHz sinusoidal input and 60 MHz switching frequency, the measured THD is -61/-62/-53 dB and corresponding efficiency is 71/83/86% with 175/200/220 mW output power level, respectively. Performance has also been verified for 2/3-level PA operation with a high PAPR signal with 500 kHz bandwidth. While intended as a general purpose amplifier, the approach is well-suited for applications such as power-line communications (PLC). The final part of the thesis introduces an efficient buck/buck-boost reconfigurable LED driver that supports PWM and PFM operation. The driver is based on peak current control. Rectified sin as well as sin² functions are employed in the reference signal to improve the power factor (PF) and total harmonic distortion (THD) of the buck and buck-boost converters. The design ensures that the peak of the inductor current maintains a constant level that is invariant for different AC line voltages. The operating mode of the design can be changed between PWM and PFM. The LED driver has been implemented in a 130-nm CMOS process. PF and THD are improved when the proposed reference is employed, and peak PF and lowest THD are 0.995/0.983/0.996 and 7.8/6.2/3.5% for the buck (PWM), buck (PFM), buck-boost (PFM) cases, respectively. The corresponding peak efficiency for the three cases is 88/92/91%, respectively.Electrical and Computer Engineerin

Energy Efficient RF Transmitter Design using Enhanced Breakdown Voltage SOI-CMOS Compatible MESFETs

abstract: The high cut-off frequency of deep sub-micron CMOS technologies has enabled the integration of radio frequency (RF) transceivers with digital circuits. However, the challenging point is the integration of RF power amplifiers, mainly due to the low breakdown voltage of CMOS transistors. Silicon-on-insulator (SOI) metal semiconductor field effect transistors (MESFETs) have been introduced to remedy the limited headroom concern in CMOS technologies. The MESFETs presented in this thesis have been fabricated on different SOI-CMOS processes without making any change to the standard fabrication steps and offer 2-30 times higher breakdown voltage than the MOSFETs on the same process. This thesis explains the design steps of high efficiency and wideband RF transmitters using the proposed SOI-CMOS compatible MESFETs. This task involves DC and RF characterization of MESFET devices, along with providing a compact Spice model for simulation purposes. This thesis presents the design of several SOI-MESFET RF power amplifiers operating at 433, 900 and 1800 MHz with ~40% bandwidth. Measurement results show a peak power added efficiency (PAE) of 55% and a peak output power of 22.5 dBm. The RF-PAs were designed to operate in Class-AB mode to minimize the linearity degradation. Class-AB power amplifiers lead to poor power added efficiency, especially when fed with signals with high peak to average power ratio (PAPR) such as wideband code division multiple access (W-CDMA). Polar transmitters have been introduced to improve the efficiency of RF-PAs at backed-off powers. A MESFET based envelope tracking (ET) polar transmitter was designed and measured. A low drop-out voltage regulator (LDO) was used as the supply modulator of this polar transmitter. MESFETs are depletion mode devices; therefore, they can be configured in a source follower configuration to have better stability and higher bandwidth that MOSFET based LDOs. Measurement results show 350 MHz bandwidth while driving a 10 pF capacitive load. A novel polar transmitter is introduced in this thesis to alleviate some of the limitations associated with polar transmitters. The proposed architecture uses the backgate terminal of a partially depleted transistor on SOI process, which relaxes the bandwidth and efficiency requirements of the envelope amplifier in a polar transmitter. The measurement results of the proposed transmitter demonstrate more than three times PAE improvement at 6-dB backed-off output power, compared to the traditional RF transmitters.Dissertation/ThesisPh.D. Electrical Engineering 201

Four-element phased-array beamformers and a self-interference canceling full-duplex transciver in 130-nm SiGe for 5G applications at 26 GHz

This thesis is on the design of radio-frequency (RF) integrated front-end circuits for next generation 5G communication systems. The demand for higher data rates and lower latency in 5G networks can only be met using several new technologies including, but not limited to, mm-waves, massive-MIMO, and full-duplex. Use of mm-waves provides more bandwidth that is necessary for high data rates at the cost of increased attenuation in air. Massive-MIMO arrays are required to compensate for this increased path loss by providing beam steering and array gain. Furthermore, full duplex operation is desirable for improved spectrum efficiency and reduced latency. The difficulty of full duplex operation is the self-interference (SI) between transmit (TX) and receive (RX) paths. Conventional methods to suppress this interference utilize either bulky circulators, isolators, couplers or two separate antennas. These methods are not suitable for fully-integrated full-duplex massive-MIMO arrays. This thesis presents circuit and system level solutions to the issues summarized above, in the form of SiGe integrated circuits for 5G applications at 26 GHz. First, a full-duplex RF front-end architecture is proposed that is scalable to massive-MIMO arrays. It is based on blind, RF self-interference cancellation that is applicable to single/shared antenna front-ends. A high resolution RF vector modulator is developed, which is the key building block that empowers the full-duplex frontend architecture by achieving better than state-of-the-art 10-b monotonic phase control. This vector modulator is combined with linear-in-dB variable gain amplifiers and attenuators to realize a precision self-interference cancellation circuitry. Further, adaptive control of this SI canceler is made possible by including an on-chip low-power IQ downconverter. It correlates copies of transmitted and received signals and provides baseband/dc outputs that can be used to adaptively control the SI canceler. The solution comes at the cost of minimal additional circuitry, yet significantly eases linearity requirements of critical receiver blocks at RF/IF such as mixers and ADCs. Second, to complement the proposed full-duplex front-end architecture and to provide a more complete solution, high-performance beamformer ICs with 5-/6- b phase and 3-/4-b amplitude control capabilities are designed. Single-channel, separate transmitter and receiver beamformers are implemented targeting massive- MIMO mode of operation, and their four-channel versions are developed for phasedarray communication systems. Better than state-of-the-art noise performance is obtained in the RX beamformer channel, with a full-channel noise figure of 3.3 d

Techniques for Wideband All Digital Polar Transmission

abstract: Modern Communication systems are progressively moving towards all-digital transmitters (ADTs) due to their high efficiency and potentially large frequency range. While significant work has been done on individual blocks within the ADT, there are few to no full systems designs at this point in time. The goal of this work is to provide a set of multiple novel block architectures which will allow for greater cohesion between the various ADT blocks. Furthermore, the design of these architectures are expected to focus on the practicalities of system design, such as regulatory compliance, which here to date has largely been neglected by the academic community. Amongst these techniques are a novel upconverted phase modulation, polyphase harmonic cancellation, and process voltage and temperature (PVT) invariant Delta Sigma phase interpolation. It will be shown in this work that the implementation of the aforementioned architectures allows ADTs to be designed with state of the art size, power, and accuracy levels, all while maintaining PVT insensitivity. Due to the significant performance enhancement over previously published works, this work presents the first feasible ADT architecture suitable for widespread commercial deployment.Dissertation/ThesisDoctoral Dissertation Electrical Engineering 201