A 0.1–5.0 GHz flexible SDR receiver with digitally assisted calibration in 65 nm CMOS

© 2017 Elsevier Ltd. All rights reserved.A 0.1–5.0 GHz flexible software-defined radio (SDR) receiver with digitally assisted calibration is presented, employing a zero-IF/low-IF reconfigurable architecture for both wideband and narrowband applications. The receiver composes of a main-path based on a current-mode mixer for low noise, a high linearity sub-path based on a voltage-mode passive mixer for out-of-band rejection, and a harmonic rejection (HR) path with vector gain calibration. A dual feedback LNA with “8” shape nested inductor structure, a cascode inverter-based TCA with miller feedback compensation, and a class-AB full differential Op-Amp with Miller feed-forward compensation and QFG technique are proposed. Digitally assisted calibration methods for HR, IIP2 and image rejection (IR) are presented to maintain high performance over PVT variations. The presented receiver is implemented in 65 nm CMOS with 5.4 mm2 core area, consuming 9.6–47.4 mA current under 1.2 V supply. The receiver main path is measured with +5 dB m/+5dBm IB-IIP3/OB-IIP3 and +61dBm IIP2. The sub-path achieves +10 dB m/+18dBm IB-IIP3/OB-IIP3 and +62dBm IIP2, as well as 10 dB RF filtering rejection at 10 MHz offset. The HR-path reaches +13 dB m/+14dBm IB-IIP3/OB-IIP3 and 62/66 dB 3rd/5th-order harmonic rejection with 30–40 dB improvement by the calibration. The measured sensitivity satisfies the requirements of DVB-H, LTE, 802.11 g, and ZigBee.Peer reviewedFinal Accepted Versio

Tunable Balun Low-Noise Amplifier in 65nm CMOS Technology

The presented paper includes the design and implementation of a 65 nm CMOS low-noise amplifier (LNA) based on inductive source degeneration. The amplifier is realized with an active balun enabling a single-ended input which is an important requirement for low-cost system on chip implementations. The LNA has a tunable bandpass characteristics from 4.7 GHz up to 5.6 GHz and a continuously tunable gain from 22 dB down to 0 dB, which enables the required flexibility for multi-standard, multi-band receiver architectures. The gain and band tuning is realized with an optimized tunable active resistor in parallel to a tunable L-C tank amplifier load. The amplifier achieves an IIP3 linearity of -8dBm and a noise figure of 2.7 dB at the highest gain and frequency setting with a low power consumption of 10 mW. The high flexibility of the proposed LNA structure together with the overall good performance makes it well suited for future multi-standard low-cost receiver front-ends

Linearity vs. Power Consumption of CMOS LNAs in LTE Systems

This paper presents a study of linearity in wideband CMOS low noise amplifiers (LNA) and its relationship to power consumption in context of Long Term Evolution (LTE) system. Using proposed figure of merit to compare 35 state-of-the-art LNA circuits published in recent years, the paper shows a proportional but relatively weak dependence between amplifier performance (that is combined linearity, noise figure and gain) with power consumption. As a result, the predicted increase of LNA performance, necessary to satisfy stringent linearity specifications of LTE standard, may require a significant increase in power, a critical budget planning aspect for both handheld devices and base stations operating in small cells

Digitally-Enhanced Software-Defined Radio Receiver Robust to Out-of-Band Interference

A software-defined radio (SDR) receiver with improved robustness to out-of-band interference (OBI) is presented. Two main challenges are identified for an OBI-robust SDR receiver: out-of-band nonlinearity and harmonic mixing. Voltage gain at RF is avoided, and instead realized at baseband in combination with low-pass filtering to mitigate blockers and improve out-of-band IIP3. Two alternative “iterative” harmonic-rejection (HR) techniques are presented to achieve high HR robust to mismatch: a) an analog two-stage polyphase HR concept, which enhances the HR to more than 60 dB; b) a digital adaptive interference cancelling (AIC) technique, which can suppress one dominating harmonic by at least 80 dB. An accurate multiphase clock generator is presented for a mismatch-robust HR. A proof-of-concept receiver is implemented in 65 nm CMOS. Measurements show 34 dB gain, 4 dB NF, and 3.5 dBm in-band IIP3 while the out-of-band IIP3 is + 16 dBm without fine tuning. The measured RF bandwidth is up to 6 GHz and the 8-phase LO works up to 0.9 GHz (master clock up to 7.2 GHz). At 0.8 GHz LO, the analog two-stage polyphase HR achieves a second to sixth order HR > dB over 40 chips, while the digital AIC technique achieves HR > 80 dB for the dominating harmonic. The total power consumption is 50 mA from a 1.2 V supply

Analysis and Design of Wideband Low Noise Amplifier with Digital Control

The design issues in designing low noise amplifier (LNA) for Software-Defined-Radio (SDR) are reviewed. An inductor-less wideband low noise amplifier aiming at low frequency band (0.2-2GHz) for Software-Defined-Radio is presented. Shunt-shunt LNA with active feedback is used as the first stage which is carefully optimized for low noise and wide band applications. A digitally controlled second stage is employed to provide an additional 12dB gain control. A novel method is proposed to bypass the first stage without degrading input matching. This LNA is fabricated in a standard 0.18 um CMOS technology. The measurement result shows the proposed LNA has a gain range of 6dB-18dB at high gain mode and -12dB-0dB at low gain mode, as well as a –3dB bandwidth of 2GHz. The noise figure (NF) is 3.5-4.5dB in the high gain setting mode. It consumes 20mW from a 1.8V supply

Flexible Receivers in CMOS for Wireless Communication

Consumers are pushing for higher data rates to support more services that are introduced in mobile applications. As an example, a few years ago video-on-demand was only accessed through landlines, but today wireless devices are frequently used to stream video. To support this, more flexible network solutions have merged in 4G, introducing new technical problems to the mobile terminal. New techniques are thus needed, and this dissertation explores five different ideas for receiver front-ends, that are cost-efficient and flexible both in performance and operating frequency. All ideas have been implemented in chips fabricated in 65 nm CMOS technology and verified by measurements. Paper I explores a voltage-mode receiver front-end where sub-threshold positive feedback transistors are introduced to increase the linearity in combination with a bootstrapped passive mixer. Paper II builds on the idea of 8-phase harmonic rejection, but simplifies it to a 6-phase solution that can reject noise and interferers at the 3rd order harmonic of the local oscillator frequency. This provides a good trade-off between the traditional quadrature mixer and the 8- phase harmonic rejection mixer. Furthermore, a very compact inductor-less low noise amplifier is introduced. Paper III investigates the use of global negative feedback in a receiver front-end, and also introduces an auxiliary path that can cancel noise from the main path. In paper IV, another global feedback based receiver front-end is designed, but with positive feedback instead of negative. By introducing global positive feedback, the resistance of the transistors in a passive mixer-first receiver front-end can be reduced to achieve a lower noise figure, while still maintaining input matching. Finally, paper V introduces a full receiver chain with a single-ended to differential LNA, current-mode downconversion mixers, and a baseband circuity that merges the functionalities of the transimpedance amplifier, channel-select filter, and analog-to-digital converter into one single power-efficient block

Current reuse topology in UWB CMOS LNA

Non

Design of broadband inductor-less RF front-ends with high dynamic range for G.hn

System-on-Chip (SoC) was adopted in recent years as one of the solutions to reduce the cost of integrated systems. When the SoC solution started to be used, the final product was actually more expensive due to lower yield. The developments in integrated technology through the years allowed the integration of more components in lesser area with a better yield. Thus, SoCs became a widely used solution to reduced the cost of the final product, integrating into a single-chip the main parts of a system: analog, digital and memory. As integrated technology kept scaling down to allow a higher density of transistors and thus providing more functionality with the same die area, the analog RF parts of the SoC became a bottleneck to cost reduction as inductors occupy a large die area and do not scale down with technology. Hence, the trend moves toward the research and design of inductor-less SoCs that further reduce the cost of the final solution. Also, as the demand for home networking high-data-rates communication systems has increased over the last decade, several standards have been developed to satisfy the requirements of each application, the most popular being wireless local area networks (WLANs) based on the IEEE 802.11 standard. However, poor signal propagation across walls make WLANs unsuitable for high-speed applications such as high-definition in-home video streaming, leading to the development of wired technologies using the existing in-home infrastructure. The ITU-T G.hn recommendation (G.9960 and G.9961) unifies the most widely used wired infrastructures at home (coaxial cables, phone lines and power lines) into a single standard for high-speed data transmission of up to 1 Gb/s. The G.hn recommendation defines a unified networking over power lines, phone lines and coaxial cables with different plans for baseband and RF. The RF-coax bandplan, where this thesis is focused, uses 50 MHz and 100 MHz bandwidth channels with 256 and 512 carriers respectively. The center frequency can range from 350 MHz to 2450 MHz. The recommendation specifies a transmission power limit of 5 dBm for the 50 MHz bandplan and 8~dBm for the 100 MHz bandplan, therefore the maximum transmitted power in each carrier is the same for both bandplans. Due to the nature of an in-home wired environment, receivers that can handle both very large and very small amplitude signals are required; when transmitter and receiver are connected on the same electric outlet there is no channel attenuation and the signal-to-noise-plus-distortion ratio (SNDR) is dominated by the receiver linearity, whereas when transmitter and receiver are several rooms apart channel attenuation is high and the SNDR is dominated by the receiver noise figure. The high dynamic range specifications for these receivers require the use of configurable-gain topologies that can provide both high-linearity and low-noise for different configurations. Thus, this thesis has been aimed at researching high dynamic range broadband inductor-less topologies to be used as the RF front-end for a G.hn receiver complying with the provided specifications. A large part of the thesis has been focused on the design of the input amplifier of the front-end, which is the most critical stage as the noise figure and linearity of the input amplifier define the achievable overall specifications of the whole front-end. Three prototypes has been manufactured using a 65 nm CMOS process: two input RFPGAs and one front-end using the second RFPGA prototype.El "sistema en un chip" (SoC) fue adoptado recientemente como una de las soluciones para reducir el coste de sistemas integrados. Cuando se empezó a utilizar la solución SoC, el producto final era más caro debido al bajo rendimiento de producción. Los avances en tecnología integrada a lo largo de los años han permitido la integración de más componentes en menos área con mejoras en rendimiento. Por lo tanto, SoCs pasó a ser una solución ampliamente utilizada para reducir el coste del producto final, integrando en un único chip las principales partes de un sistema: analógica, digital y memoria. A medida que las tecnologías integradas se reducían en tamaño para permitir una mayor densisdad de transistores y proveer mayor funcionalidad con la misma área, las partes RF analógicas del SoC pasaron a ser la limitación en la reducción de costes ya que los inductores ocupan mucha área y no escalan con la tecnología. Por lo tanto, las tendencias en investigación se mueven hacia el diseño de SoCs sin inductores que todavía reducen más el coste final del producto. También, a medida que la demanda en sistemas de comunicación domésticos de alta velocidad ha crecido a lo largo de la última década, se han desarrollado varios estándares para satisfacer los requisitos de cada aplicación, siendo las redes sin hilos (WLANs) basadas en el estándar IEEE 802.11 las más populares. Sin embargo, una pobre propagación de señal a través de las paredes hacen que las WLANs sean inadecuadas para aplicaciones de alta-velocidad como transmisión de vídeo de alta definición en tiempo real, resultando en el desarrollo de tecnologías con hilos utilizando la infraestructura existente en los domicilios. La recomendación ITU-T G.hn (G.9960 and G.9961) unifica las principales infraestructuras con hilos domésticas (cables coaxiales, línias de teléfono y línias de electricidad) en un sólo estándar para la transmisión de datos hasta 1 Gb/s. La recomendación G.hn define una red unificada sobre línias de electricidad, de teléfono y coaxiales con diferentes esquemas para banda base y RF. El esquema RF-coax en el cual se basa esta tesis, usa canales con un ancho de banda de 50 MHz y 100 MHz con 256 y 512 portadoras respectivamente. La frecuencia centra puede variar desde 350 MHz hasta 2450 MHz. La recomendación especifica un límite en la potencia de transmisión de 5 dBm para el esquema de 50 MHz y 8 dBm para el esquema de 100 MHz, de tal forma que la potencia máxima por portadora es la misma en ambos esquemas. Debido a la estructura de un entorno doméstico con hilos, los receptores deben ser capaces de procesar señales con amplitud muy grande o muy pequeña; cuando transmisor y receptor están conectados en la misma toma eléctrica no hay atenuación de canal y el ratio de señal a rudio más distorsión (SNDR) está dominado por la linealidad del receptor, mientras que cuando transmisor y receptor están separados por varias habitaciones la atenuación es elevada y el SNDR está dominado por la figura de ruido del receptor. Los elevados requisitos de rango dinámico para este tipo de receptores requieren el uso de topologías de ganancia configurable que pueden proporcionar tanto alta linealidad como bajo ruido para diferentes configuraciones. Por lo tanto, esta tesis está encarada a la investigación de topologías sin inductores de banda ancha y elevado rango dinámico para ser usadas a la entrada de un receptor G.hn cumpliendo con las especificaciones proporcionadas. Una gran parte de la tesis se ha centrado en el diseño del amplificador de entrada al ser la etapa más crítica, ya que la figura de ruido y linealidad del amplificador de entrada definen lás máximas especificaciones que el sistema puede conseguir. Se han fabricado 3 prototipos con un proceso CMOS de 65 nm: 2 amplificadores y un sistema completo con amplificador y mezclador.Postprint (published version

Discrete-Time Mixing Receiver Architecture for RF-Sampling Software-Defined Radio

A discrete-time (DT) mixing architecture for RF-sampling receivers is presented. This architecture makes RF sampling more suitable for software-defined radio (SDR) as it achieves wideband quadrature demodulation and wideband harmonic rejection. The paper consists of two parts. In the first part, different downconversion techniques are classified and compared, leading to the definition of a DT mixing concept. The suitability of CT-mixing and RF-sampling receivers to SDR is also discussed. In the second part, we elaborate the DT-mixing architecture, which can be realized by de-multiplexing. Simulation shows a wideband 90° phase shift between I and Q outputs without systematic channel bandwidth limitation. Oversampling and harmonic rejection relaxes RF pre-filtering and reduces noise and interference folding. A proof-of-concept DT-mixing downconverter has been built in 65 nm CMOS, for 0.2 to 0.9 GHz RF band employing 8-times oversampling. It can reject 2nd to 6th harmonics by 40 dB typically and without systematic channel bandwidth limitation. Without an LNA, it achieves a gain of -0.5 to 2.5 dB, a DSB noise figure of 18 to 20 dB, an IIP3 = +10 dBm, and an IIP2 = +53 dBm, while consuming less than 19 mW including multiphase clock generation