Low-power CMOS front-ends for wireless personal area networks

The potential of implementing subthreshold radio frequency circuits in deep sub-micron CMOS technology was investigated for developing low-power front-ends for wireless personal area network (WPAN) applications. It was found that the higher transconductance to bias current ratio in weak inversion could be exploited in developing low-power wireless front-ends, if circuit techniques are employed to mitigate the higher device noise in subthreshold region. The first fully integrated subthreshold low noise amplifier was demonstrated in the GHz frequency range requiring only 260 μW of power consumption. Novel subthreshold variable gain stages and down-conversion mixers were developed. A 2.4 GHz receiver, consuming 540 μW of power, was implemented using a new subthreshold mixer by replacing the conventional active low noise amplifier by a series-resonant passive network that provides both input matching and voltage amplification. The first fully monolithic subthreshold CMOS receiver was also implemented with integrated subthreshold quadrature LO (Local Oscillator) chain for 2.4 GHz WPAN applications. Subthreshold operation, passive voltage amplification, and various low-power circuit techniques such as current reuse, stacking, and differential cross coupling were combined to lower the total power consumption to 2.6 mW. Extremely compact resistive feedback CMOS low noise amplifiers were presented as a cost-effective alternative to narrow band LNAs using high-Q inductors. Techniques to improve linearity and reduce power consumption were presented. The combination of high linearity, low noise figure, high broadband gain, extremely small die area and low power consumption made the proposed LNA architecture a compelling choice for many wireless applications.Ph.D.Committee Chair: Laskar, Joy; Committee Member: Chakraborty, Sudipto; Committee Member: Chang, Jae Joon; Committee Member: Divan, Deepakraj; Committee Member: Kornegay, Kevin; Committee Member: Tentzeris, Emmanoui

Recursive receiver down-converters with multiband feedback and gain-reuse for low-power applications

Power minimization in wireless transceivers has become increasingly critical in recent years with the emergence of standards for short-distance applications in the 900 MHz and 2.4 GHz industrial, scientific and medical (ISM) radio bands. The demand for long battery life and better portability in such applications has led to extensive research on low power radio architectures. This dissertation introduces receiver topologies for low-power systems and presents a theoretical performance analysis of the topologies. Two fully integrated receiver down-converters that demonstrate the concept are implemented in a 0.13-[mu]m CMOS technology. These topologies employ merged mixers and IF amplifiers in order to reduce power dissipation for a given dynamic range performance. In the described topologies, the input stage of a mixer is used to simultaneously provide conversion gain and baseband amplification. This is achieved by applying the down-converted IF signal to input of the mixer. Consequently, the effective conversion gain of the design is greatly enhanced with current requirement primarily determined by the input transconductor. Potential degradation mechanisms related to instability and second-order distortion are identified and solved by the use of appropriate circuit techniques. Noise and linearity performance of the down-converters is analyzed and compared to that of conventional cascaded design counterparts. The potential for enhancement of IIP3 performance through cancellation of nonlinear products is discussed. Potential extensions of the above work including feedback-based architectures that exploit multiple loops for further maximizing the power efficiency of receiver front-ends are also presented.Electrical and Computer Engineerin

Energy-Efficient Wireless Circuits and Systems for Internet of Things

As the demand of ultra-low power (ULP) systems for internet of thing (IoT) applications has been increasing, large efforts on evolving a new computing class is actively ongoing. The evolution of the new computing class, however, faced challenges due to hard constraints on the RF systems. Significant efforts on reducing power of power-hungry wireless radios have been done. The ULP radios, however, are mostly not standard compliant which poses a challenge to wide spread adoption. Being compliant with the WiFi network protocol can maximize an ULP radio’s potential of utilization, however, this standard demands excessive power consumption of over 10mW, that is hardly compatible with in ULP systems even with heavy duty-cycling. Also, lots of efforts to minimize off-chip components in ULP IoT device have been done, however, still not enough for practical usage without a clean external reference, therefore, this limits scaling on cost and form-factor of the new computer class of IoT applications. This research is motivated by those challenges on the RF systems, and each work focuses on radio designs for IoT applications in various aspects. First, the research covers several endeavors for relieving energy constraints on RF systems by utilizing existing network protocols that eventually meets both low-active power, and widespread adoption. This includes novel approaches on 802.11 communication with articulate iterations on low-power RF systems. The research presents three prototypes as power-efficient WiFi wake-up receivers, which bridges the gap between industry standard radios and ULP IoT radios. The proposed WiFi wake-up receivers operate with low power consumption and remain compatible with the WiFi protocol by using back-channel communication. Back-channel communication embeds a signal into a WiFi compliant transmission changing the firmware in the access point, or more specifically just the data in the payload of the WiFi packet. With a specific sequence of data in the packet, the transmitter can output a signal that mimics a modulation that is more conducive for ULP receivers, such as OOK and FSK. In this work, low power mixer-first receivers, and the first fully integrated ultra-low voltage receiver are presented, that are compatible with WiFi through back-channel communication. Another main contribution of this work is in relieving the integration challenge of IoT devices by removing the need for external, or off-chip crystals and antennas. This enables a small form-factor on the order of mm3-scale, useful for medical research and ubiquitous sensing applications. A crystal-less small form factor fully integrated 60GHz transceiver with on-chip 12-channel frequency reference, and good peak gain dual-mode on-chip antenna is presented.PHDElectrical and Computer EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/162975/1/jaeim_1.pd

Design Of Low-Noise Amplifier Utilising Active Shunt Feedback For Medradio Band Applications

A low-power 0.18-µm CMOS low-noise amplifier (LNA) for MedRadio applications has been designed and verified in this research work. Cadence IC5 software with Silterra’s C18G CMOS Process Design Kit were used for all design and simulation work. This LNA utilises complementary common-source current-reuse topology and subthreshold biasing to achieve low-power operation with simultaneous high gain and low noise figure. An active shunt feedback circuit is used as input matching network to provide a suitable input return loss. For test and measurement purpose, an output buffer was designed and integrated with this LNA. Inductorless design approach of this LNA, together with the use of MOSCAPs as capacitors, help to minimise the die size. On post-layout simulations with simulated total power consumption of 0.5 mW, all targeted specifications are met albeit with some degradations from the pre-layout simulation results. From pre-layout to post-layout simulations, the simulated gain and input return loss are reduced to 16.3 dB and 10.1 dB respectively whilst the simulated noise figure worsens to 4.9 dB. However, the simulated IP1dB and IIP3 slightly improve to -26.7 dBm and -18.6 dBm respectively. Overall, the post-layout simulated performance of this proposed LNA is fairly comparable to some current state-of-the-art LNAs for MedRadio applications. However, the worsening simulated input return loss and noise figure at post-layout level due to parasitic capacitances and resistances in the integrated circuit layout need to be given serious attention. This is because the post-layout simulation results of these two parameters virtually have no margin to their respective targeted specifications

Configurable circuits and their impact on multi-standard RF front-end architectures

This thesis studies configurable circuits and their impact on multi-standard RF front-end architectures. In particular, low-voltage low-power linear LNA and mixer topologies suitable for implementation in multi-standard front-ends are subject of the investigation. With respect to frequency and bandwidth, multi-standard front-ends can be implemented using either tunable or wideband LNA and mixer topologies. Based on the type of the LNA and mixer(s), multi-standard receiver RF front-ends can be divided into three groups. They can be (tunable) narrow-band, wide-band or combined. The advantages and disadvantages of the different multi-standard receiver RF front-ends have been discussed in detail. The partitioning between off-chip selectivity, on-chip selectivity provided by the LNA and mixer, linearity, power consumption and occupied chip area in each multi-standard RF front-end group are thoroughly investigated. A Figure of Merit (FOM) for the multi-standard receiver RF front-end has been introduced. Based on this FOM the most suitable multi-standard RF front-end group in terms of cost-effectiveness can be selected. In order to determine which multi-standard RF front-end group is the most cost-effective for a practical application, a GSM850/E-GSM/DCS/PCS/Bluetooth/WLANa/b/g multi-standard receiver RF front-end is chosen as a demonstrator. These standards are the most frequently used standards in wireless communication, and this combination of standards allows to users almost "anytime-anywhere" voice and data transfer. In order to verify these results, three demonstrators have been defined, designed and implemented, two wideband RF front-end circuits in 90nm CMOS and 65nm CMOS, and one combined multi-standard RF front-end circuit in 65nm CMOS. The proposed multi-standard demonstrators have been compared with the state-of the art narrow-band, wide-band and combined multi-standard RF front-ends. On the proposed multi-standard RF front-ends and the state-of the art multi-standard RF front-ends the proposed FOM have been applied. The comparison shows that the combined multi-standard RF front-end group is the most cost effective multi-standard group for this application

System-on-Package Low-Power Telemetry and Signal Conditioning unit for Biomedical Applications

Recent advancements in healthcare monitoring equipments and wireless communication technologies have led to the integration of specialized medical technology with the pervasive wireless networks. Intensive research has been focused on the development of medical wireless networks (MWN) for telemedicine and smart home care services. Wireless technology also shows potential promises in surgical applications. Unlike conventional surgery, an expert surgeon can perform the surgery from a remote location using robot manipulators and monitor the status of the real surgery through wireless communication link. To provide this service each surgical tool must be facilitated with smart electronics to accrue data and transmit the data successfully to the monitoring unit through wireless network. To avoid unwieldy wires between the smart surgical tool and monitoring units and to reap the benefit of excellent features of wireless technology, each smart surgical tool must incorporate a low-power wireless transmitter. Low-power transmitter with high efficiency is essential for short range wireless communication. Unlike conventional transmitters used for cellular communication, injection-locked transmitter shows greater promises in short range wireless communication. The core block of an injection-locked transmitter is an injection-locked oscillator. Therefore, this research work is directed towards the development of a low-voltage low-power injection-locked oscillator which will facilitate the development of a low-power injection-locked transmitter for MWN applications. Structure of oscillator and types of injection are two crucial design criteria for low-power injection-locked oscillator design. Compared to other injection structures, body-level injection offers low-voltage and low-power operation. Again, conventional NMOS/PMOS-only cross-coupled LC oscillator can work with low supply voltage but the power consumption is relatively high. To overcome this problem, a self-cascode LC oscillator structure has been used which provides both low-voltage and low-power operation. Body terminal coupling is used with this structure to achieve injection-locking. Simulation results show that the self-cascode structure consumes much less power compared to that of the conventional structure for the same output swing while exhibiting better phase noise performance. Usage of PMOS devices and body bias control not only reduces the flicker noise and power consumption but also eliminates the requirements of expensive fabrication process for body terminal access

Ultra Small Antenna and Low Power Receiver for Smart Dust Wireless Sensor Networks

Wireless Sensor Networks have the potential for profound impact on our daily lives. Smart Dust Wireless Sensor Networks (SDWSNs) are emerging members of the Wireless Sensor Network family with strict requirements on communication node sizes (1 cubic centimeter) and power consumption (< 2mW during short on-states). In addition, the large number of communication nodes needed in SDWSN require highly integrated solutions. This dissertation develops new design techniques for low-volume antennas and low-power receivers for SDWSN applications. In addition, it devises an antenna and low noise amplifier co-design methodology to increase the level of design integration, reduce receiver noise, and reduce the development cycle. This dissertation first establishes stringent principles for designing SDWSN electrically small antennas (ESAs). Based on these principles, a new ESA, the F-Inverted Compact Antenna (FICA), is designed at 916MHz. This FICA has a significant advantage in that it uses a small-size ground plane. The volume of this FICA (including the ground plane) is only 7% of other state-of-the-art ESAs, while its efficiency (48.53%) and gain (-1.38dBi) are comparable to antennas of much larger dimensions. A physics-based circuit model is developed for this FICA to assist system level design at the earliest stage, including optimization of the antenna performance. An antenna and low noise amplifier (LNA) co-design method is proposed and proven to be valid to design low power LNAs with the very low noise figure of only 1.5dB. To reduce receiver power consumption, this dissertation proposes a novel LNA active device and an input/ouput passive matching network optimization method. With this method, a power efficient high voltage gain cascode LNA was designed in a 0.13um CMOS process with only low quality factor inductors. This LNA has a 3.6dB noise figure, voltage gain of 24dB, input third intercept point (IIP3) of 3dBm, and power consumption of 1.5mW at 1.0V supply voltage. Its figure of merit, using the typical definition, is twice that of the best in the literature. A full low power receiver is developed with a sensitivity of -58dBm, chip area of 1.1mm2, and power consumption of 2.85mW

Design of a Direct-Modulation Transmitter with Self-Optimizing Feedback and a Highly Linear, Highly Reconfigurable, Continuously-Tunable Active-RC Baseband Filter for Multiple Standards

This work consists of two main parts: i) Design and implementation of a compact current-reusing 2.4GHz direct-modulation transmitter with on-chip automatic tuning; ii) Design and implementation of a novel highly-reconfigurable, continuously tunable, power-adjustable Active-RC filter for multiple standards. The design, analysis, and experimental verification of a proposed self-calibrating, current reused 2.4GHz, direct-modulation transmitter are introduced. A stacked arrangement of the power amplifier/voltage-controlled oscillator is presented along with a novel LC-tank-tuning algorithm with a simple, low-cost, on-chip implementation. To transmit maximum power, the tuning loop ensures the PA's resonant tank is centered around the operating frequency, and the loop requires no ADC, DSP, or external signal generator. This work also details the proposed tuning-loop algorithm and examines the frequency-dependent nonlinear power-detector. The system was implemented in TSMC 0.18[mu]m CMOS, occupies 0.7 mm² (TX) + 0.1 mm² (self tuning), and was measured in a QFN48 package on FR4 PCB. Automatically adjusting the tank-tuning bits within their tuning range results in >4dB increase in output power. With the self-tuning circuit active, the transmitter delivers a measured output power of > 0dBm to a 100-[omega] differential load, and the system consumes 22.9 mA from a 2.2-V supply. A biquad design methodology and a baseband low-pass filter is presented for wireless and wireline applications with reconfigurable frequency response, selectable order (1st/3rd/5th), continuously tunable cutoff frequency (1MHz-20MHz) and adjustable power consumption (3mW-7.5mW). A discrete capacitor array coarsely tunes the low-pass filter, and a novel Continuous Impedance Multiplier (CIM) then finely tunes the filter. Resistive/capacitive networks select between the Chebyshev and Inverse Chebyshev approximation types. Also, a new stability metric for biquads, Minimum Acceptable Phase Margin (MAPM), is presented and discussed in the context of filter compensation and passband ripple considerations. Experimental results yield an IIP3 of 31.3dBm, a THD of -40dB at 447mV[subscript pk, diff] input signal amplitude, and a DR of 71.4dB. The filters tunable range covers frequencies from 1MHz to 20MHz. In Inverse Chebyshev mode, the filter achieves a passband group delay variation less than ±2:5%. The design is fabricated in 0.13[mu]m CMOS, occupies 1.53mm², and operates from a 1-V supply

Energy Aware RF Transceiver for Wireless Body Area Networks (WBAN)

Ph.DDOCTOR OF PHILOSOPH

Circuit Design Techniques For Wideband Phased Arrays

University of Minnesota Ph.D. dissertation.June 2015. Major: Electrical Engineering. Advisor: Ramesh Harjani. 1 computer file (PDF); xii, 143 pages.This dissertation focuses on beam steering in wideband phased arrays and phase noise modeling in injection locked oscillators. Two different solutions, one in frequency and one in time, have been proposed to minimize beam squinting in phased arrays. Additionally, a differential current reuse frequency doubler for area and power savings has been proposed. Silicon measurement results are provided for the frequency domain solution (IBM 65nm RF CMOS), injection locked oscillator model verification (IBM 130nm RF-CMOS) and frequency doubler (IBM 65nm RF CMOS), while post extraction simulation results are provided for the time domain phased array solution (the chip is currently under fabrication, TSMC 65nm RF CMOS). In the frequency domain solution, a 4-point passive analog FFT based frequency tunable filter is used to channelize an incoming wideband signal into multiple narrowband signals, which are then processed through independent phase shifters. A two channel prototype has been developed at 8GHz RF frequency. Three discrete phase shifts (0 & +/- 90 degrees) are implemented through differential I-Q swapping with appropriate polarity. A minimum null-depth of 19dB while a maximum null-depth of 27dB is measured. In the time domain solution, a discrete time approach is undertaken with signals getting sampled in order of their arrival times. A two-channel prototype for a 2GHz instantaneous RF bandwidth (7GHz-9GHz) has been designed. A QVCO generates quadrature LO signals at 8GHz which are phase shifted through a 5-bit (2 extra bits from differential I-Q swapping with appropriate polarity) cartesian combiner. Baseband sampling clocks are generated from phase shifted LOs through a CMOS divide by 4 with independent resets. The design achieves an average time delay of 4.53ps with 31.5mW of power consumption (per channel, buffers excluded). An injection locked oscillator has been analyzed in s-domain using Paciorek's time domain transient equations. The simplified analysis leads to a phase noise model identical to that of a type-I PLL. The model is equally applicable to injection locked dividers and multipliers and has been extended to cover all injection locking scenarios. The model has been verified against a discrete 57MHz Colpitt's ILO, a 6.5GHz ILFD and a 24GHz ILFM with excellent matching between the model and measurements. Additionally, a differential current reuse frequency doubler, for frequency outputs between 7GHz to 14GHz, design has been developed to reduce passive area and dc power dissipation. A 3-bit capacitive tuning along with a tail current source is used to better conversion efficiency. The doubler shows FOM$_{T}$ values between 191dBc/Hz to 209dBc/Hz when driven by a 0.7GHz to 5.8GHz wide tuning VCO with a phase noise that ranges from -114dBc/Hz to -112dBc/Hz over the same bandwidth