Synchronization Techniques for Burst-Mode Continuous Phase Modulation

Synchronization is a critical operation in digital communication systems, which establishes and maintains an operational link between transmitter and the receiver. As the advancement of digital modulation and coding schemes continues, the synchronization task becomes more and more challenging since the new standards require high-throughput functionality at low signal-to-noise ratios (SNRs). In this work, we address feedforward synchronization of continuous phase modulations (CPMs) using data-aided (DA) methods, which are best suited for burst-mode communications. In our transmission model, a known training sequence is appended to the beginning of each burst, which is then affected by additive white Gaussian noise (AWGN), and unknown frequency, phase, and timing offsets. Based on our transmission model, we derive the Cramer-Rao bound (CRB) for DA joint estimation of synchronization parameters. Using the CRB expressions, the optimum training sequence for CPM signals is proposed. It is shown that the proposed sequence minimizes the CRB for all three synchronization parameters asymptotically, and can be applied to the entire CPM family. We take advantage of the simple structure of the optimized training sequence in order to design a practical synchronization algorithm based on the maximum likelihood (ML) principles. The proposed DA algorithm jointly estimates frequency offset, carrier phase and symbol timing in a feedforward manner. The frequency offset estimate is first found by means of maximizing a one dimensional function. It is then followed by symbol timing and carrier phase estimation, which are carried out using simple closed-form expressions. We show that the proposed algorithm attains the theoretical CRBs for all synchronization parameters for moderate training sequence lengths and all SNR regions. Moreover, a frame synchronization algorithm is developed, which detects the training sequence boundaries in burst-mode CPM signals. The proposed training sequence and synchronization algorithm are extended to shaped-offset quadrature phase-shift keying (SOQPSK) modulation, which is considered for next generation aeronautical telemetry systems. Here, it is shown that the optimized training sequence outperforms the one that is defined in the draft telemetry standard as long as estimation error variances are considered. The overall bit error rate (BER) plots suggest that the optimized preamble with a shorter length can be utilized such that the performance loss is less than 0.5 dB of an ideal synchronization scenario

CHANNEL CODING TECHNIQUES FOR A MULTIPLE TRACK DIGITAL MAGNETIC RECORDING SYSTEM

In magnetic recording greater area) bit packing densities are achieved through increasing track density by reducing space between and width of the recording tracks, and/or reducing the wavelength of the recorded information. This leads to the requirement of higher precision tape transport mechanisms and dedicated coding circuitry. A TMS320 10 digital signal processor is applied to a standard low-cost, low precision, multiple-track, compact cassette tape recording system. Advanced signal processing and coding techniques are employed to maximise recording density and to compensate for the mechanical deficiencies of this system. Parallel software encoding/decoding algorithms have been developed for several Run-Length Limited modulation codes. The results for a peak detection system show that Bi-Phase L code can be reliably employed up to a data rate of 5kbits/second/track. Development of a second system employing a TMS32025 and sampling detection permitted the utilisation of adaptive equalisation to slim the readback pulse. Application of conventional read equalisation techniques, that oppose inter-symbol interference, resulted in a 30% increase in performance. Further investigation shows that greater linear recording densities can be achieved by employing Partial Response signalling and Maximum Likelihood Detection. Partial response signalling schemes use controlled inter-symbol interference to increase recording density at the expense of a multi-level read back waveform which results in an increased noise penalty. Maximum Likelihood Sequence detection employs soft decisions on the readback waveform to recover this loss. The associated modulation coding techniques required for optimised operation of such a system are discussed. Two-dimensional run-length-limited (d, ky) modulation codes provide a further means of increasing storage capacity in multi-track recording systems. For example the code rate of a single track run length-limited code with constraints (1, 3), such as Miller code, can be increased by over 25% when using a 4-track two-dimensional code with the same d constraint and with the k constraint satisfied across a number of parallel channels. The k constraint along an individual track, kx, can be increased without loss of clock synchronisation since the clocking information derived by frequent signal transitions can be sub-divided across a number of, y, parallel tracks in terms of a ky constraint. This permits more code words to be generated for a given (d, k) constraint in two dimensions than is possible in one dimension. This coding technique is furthered by development of a reverse enumeration scheme based on the trellis description of the (d, ky) constraints. The application of a two-dimensional code to a high linear density system employing extended class IV partial response signalling and maximum likelihood detection is proposed. Finally, additional coding constraints to improve spectral response and error performance are discussed.Hewlett Packard, Computer Peripherals Division (Bristol

Network Interface Design for Network-on-Chip

In the culture of globalized integrated circuit (IC, a.k.a chip) production, the use of Intellectual Property (IP) cores, computer aided design tools (CAD) and testing services from un-trusted vendors are prevalent to reduce the time to market. Unfortunately, the globalized business model potentially creates opportunities for hardware tampering and modification from adversary, and this tampering is known as hardware Trojan (HT). Network-on-chip (NoC) has emerged as an efficient on-chip communication infrastructure. In this work, the security aspects of NoC network interface (NI), one of the most critical components in NoC will be investigated and presented. Particularly, the NI design, hardware attack models and countermeasures for NI in a NoC system are explored. An OCP compatible NI is implemented in an IBM0.18ìm CMOS technology. The synthesis results are presented and compared with existing literature. Second, comprehensive hardware attack models targeted for NI are presented from system level to circuit level. The impact of hardware Trojans on NoC functionality and performance are evaluated. Finally, a countermeasure method is proposed to address the hardware attacks in NIs

Characteristics of multi-h coded modulation

Includes bibliographical references (leaves 74-75).Multi-h Coded Continuous-Phase Frequency Shift Keying (Multi-h CPFSK) has gained interest in recent years because it offers an additional degree of freedom in the coding of CPFSK. Similar to Trellis Coded Modulation (TCM), it does not use redundancy to achieve coding gain. Hence with properly chosen modulation indices, impact to spectral occupancy is kept to a minimum. While there has been less attention given of this method as compared with TCM, this method can also be used with data coding. In cases where data coding is to be implemented, simultaneous use of Multi-h coding can be implemented with very little increase in complexity. In this thesis, a thorough mathematical review of this technique is made. A multi-oscillator multih coded modulator is shown similar to one presented by Massey for MSK. A unique analytical tool called a multi-oscillator trellis is presented. This considers the phase transitions with respect to each of the signalling frequencies instead of the center frequency, f₀. The multi-oscillator trellis is used to determine the state machine that will switch a bank of oscillators. The purpose of the state machine is to maintain continuous phase at the multi-oscillator output while generating the proper signal frequencies according to the data and modulation index. The Maximum Likelihood Detection process at the receiver is shown as a partition of an uncoded CPFSK signal. Finally, an analysis is made to determine if a modulator with a non-linear frequencyvoltage characteristic is suitable in a coherent multi-h coded application. Much of the literature on this topic has been comparative to PSK. It is the intent of this work to use FSK and MSK as the baseline to determine how existing structures may be extended to realize the benefits of multi-h coding. The application of this coding to an 8 Mbps 23 GHz CPFSK point-to-point terrestrial communications system is also a topic of this thesis. It is in this context that the analysis is made

On the Effects of Estimation Error and Jitter in Ultra-Wideband Communication

The opening of the 3.6 - 10.1 GHz frequency spectrum below the \u27noise-floor\u27 by the FCC in 2002 has made possible the prospect of reusing this frequency spectrum through ultra-wideband (UWB) communication. In this thesis, we compare the performance of several UWB systems in the presence of estimation error and jitter. We then develop two alternative decision schemes to combat the effect of jitter in the UWB system. Numerical results show that one of the schemes provides significantly better performance in the presence of severe jitter than maximal ratio combining and minimal degradation of performance if jitter is not present. A generalized maximal ratio combining decision scheme to combat the presence of estimation error is also proposed. It is shown that the generalized scheme outperforms traditional maximal ratio combining

The ATLAS TRT electronics

The ATLAS inner detector consists of three sub-systems: the pixel detector spanning the radius range 4cm-20cm, the semiconductor tracker at radii from 30 to 52 cm, and the transition radiation tracker (TRT), tracking from 56 to 107 cm. The TRT provides a combination of continuous tracking with many projective measurements based on individual drift tubes (or straws) and of electron identification based on transition radiation from fibres or foils interleaved between the straws themselves. This paper describes the on and off detector electronics for the TRT as well as the TRT portion of the data acquisition (DAQ) system

Software-Driven and Virtualized Architectures for Scalable 5G Networks

In this dissertation, we argue that it is essential to rearchitect 4G cellular core networks–sitting between the Internet and the radio access network–to meet the scalability, performance, and flexibility requirements of 5G networks. Today, there is a growing consensus among operators and research community that software-defined networking (SDN), network function virtualization (NFV), and mobile edge computing (MEC) paradigms will be the key ingredients of the next-generation cellular networks. Motivated by these trends, we design and optimize three core network architectures, SoftMoW, SoftBox, and SkyCore, for different network scales, objectives, and conditions. SoftMoW provides global control over nationwide core networks with the ultimate goal of enabling new routing and mobility optimizations. SoftBox attempts to enhance policy enforcement in statewide core networks to enable low-latency, signaling-efficient, and customized services for mobile devices. Sky- Core is aimed at realizing a compact core network for citywide UAV-based radio networks that are going to serve first responders in the future. Network slicing techniques make it possible to deploy these solutions on the same infrastructure in parallel. To better support mobility and provide verifiable security, these architectures can use an addressing scheme that separates network locations and identities with self-certifying, flat and non-aggregatable address components. To benefit the proposed architectures, we designed a high-speed and memory-efficient router, called Caesar, for this type of addressing schemePHDComputer Science & EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttps://deepblue.lib.umich.edu/bitstream/2027.42/146130/1/moradi_1.pd

차세대 자동차용 카메라 데이터 통신을 위한 비대칭 동시 양방향 송수신기의 설계

학위논문(박사) -- 서울대학교대학원 : 공과대학 전기·정보공학부, 2022.2. 정덕균.본 학위 논문에서는 차세대 자동차용 카메라 링크를 위해 높은 속도의 4레벨 펄스 진폭 변조 신호와 낮은 속도의 2레벨 펄스 진폭 변조 신호를 통신하는 비대칭 동시 양방향 송수신기의 설계 기술에 대해 제안하고 검증되었다. 첫번째 프로토타입 설계에서는, 10B6Q 직류 밸런스 코드를 탑재한 4레벨 펄스 진폭 변조 송신기와 고정된 데이터와 참조 레벨을 가지는 4레벨 펄스 진폭 변조 적응형 수신기에 대한 내용이 기술되었다. 4레벨 펄스 진폭 변조 송신기에서는 교류 연결 링크 시스템에 대응하기 위한 면적 및 전력 효율성이 좋은 10B6Q 코드가 제안되었다. 이 코드는 직류 밸런스를 맞추고 연속적으로 같은 심볼을 가지는 길이를 6개로 제한 시킨다. 비록 여기서는 입력 데이터 길이 10비트를 사용하였지만, 제안된 기술은 카메라의 다양한 데이터 타입에 대응할 수 있도록 입력 데이터 길이에 대한 확장성을 가진다. 반면, 4레벨 펄스 진폭 변조 적응형 수신기에서는, 샘플러의 옵셋을 최적으로 제거하여 더 낮은 비트에러율을 얻기 위해서, 기존의 데이터 및 참조 레벨을 조절하는 대신, 이 레벨들은 고정시키고 가변 게인 증폭기를 적응형으로 조절하도록 하였다. 상기 10B6Q 코드 및 고정 데이터 및 참조레벨 기술을 가진 프로토타입 칩들은 40 나노미터 상호보완형 메탈 산화 반도체 공정으로 제작되었고 칩 온 보드 형태로 평가되었다. 10B6Q 코드는 합성 게이트 숫자는 645개와 함께 단 0.0009 mm2 의 면적 만을 차지한다. 또한, 667 MHz 동작 주파수에서 단 0.23 mW 의 전력을 소모한다. 10B6Q 코드를 탑재한 송신기에서 8-Gb/s 4레벨 펄스 진폭 변조 신호를 고정 데이터 및 참조 레벨을 가지는 적응형 수신기로 12-m 케이블 (22-dB 채널 로스) 을 통해서 보낸 결과 최소 비트 에러율 108 을 달성하였고, 비트 에러율 105 에서는 아이 마진이 0.15 UI x 50 mV 보다 크게 측정되었다. 송수신기를 합친 전력 소모는 65.2 mW (PLL 제외) 이고, 성과의 대표수치는 0.37 pJ/b/dB 를 보여주었다. 첫번째 프로토타입 설계을 포함하여 개선된 두번째 프로토타입 설계에서는, 12-Gb/s 4레벨 펄스 진폭 변조 정방향 채널 신호와 125-Mb/s 2레벨 펄스 진폭 변조 역방향 채널 신호를 탑재한 비대칭 동시 양방향 송수신기에 대해 기술되고 검증되었다. 제안된 넓은 선형 범위를 가지는 하이브리드는 gmC 저대역 통과 필터와 에코 제거기와 함께 아웃바운드 신호를 24 dB 이상 효율적으로 감소시켰다. 또한, 넓은 선형 범위를 가지는 하이브리드와 함께 게인 감소기를 형성하게 되는 선형 범위 증폭기를 통해 4레벨 펄스 진폭 변조 신호의 선형성과 진폭의 트레이드 오프 관계를 깨는 것이 가능하였다. 동시 양방향 송수신기 칩은 40 나노미터 상호보완형 메탈 산화 반도체 공정으로 제작되었다. 상기 설계 기술들을 이용하여, 4레벨 펄스 진폭 변조 및 2레벨 펄스 진폭 변조 송수신기 모두 5m 채널 (채널 로스 15.9 dB) 에서 1E-12 보다 낮은 비트 에러율을 달성하였고, 총 78.4 mW 의 전력 소모를 기록하였다. 종합적인 송수신기는 성과 대표지표로 0.41 pJ/b/dB 와 함께 동시 양방향 통신 아래에서 4레벨 펄스 진폭 변조 신호 및 2레벨 펄스 진폭 변조 신호 각각에서 아이 마진 0.15 UI 와 0.57 UI 를 달성하였다. 이 수치는 성과 대표지표 0.5 이하를 가지는 기존 동시 양방향 송수신기와의 비교에서 최고의 아이 마진을 기록하였다.In this dissertation, design techniques of a highly asymmetric simultaneous bidirectional (SB) transceivers with high-speed PAM-4 and low-speed PAM-2 signals are proposed and demonstrated for the next-generation automotive camera link. In a first prototype design, a PAM-4 transmitter with 10B6Q DC balance code and a PAM-4 adaptive receiver with fixed data and threshold levels (dtLevs) are presented. In PAM-4 transmitter, an area- and power-efficient 10B6Q code for an AC coupled link system that guarantees DC balance and limited run length of six is proposed. Although the input data width of 10 bits is used here, the proposed scheme has an extensibility for the input data width to cover various data types of the camera. On the other hand, in the PAM-4 adaptive receiver, to optimally cancel the sampler offset for a lower BER, instead of adjusting dtLevs, the gain of a programmable gain amplifier is adjusted adaptively under fixed dtLevs. The prototype chips including above proposed 10B6Q code and fixed dtLevs are fabricated in 40-nm CMOS technology and tested in chip-on-board assembly. The 10B6Q code only occupies an active area of 0.0009 mm2 with a synthesized gate count of 645. It also consumes 0.23 mW at the operating clock frequency of 667 MHz. The transmitter with 10B6Q code delivers 8-Gb/s PAM-4 signal to the adaptive receiver using fixed dtLevs through a lossy 12-m cable (22-dB channel loss) with a BER of 1E-8, and the eye margin larger than 0.15 UI x 50 mV is measured for a BER of 1E-5. The proto-type chips consume 65.2 mW (excluding PLL), exhibiting an FoM of 0.37 pJ/b/dB. In a second prototype design advanced from the first prototypes, An asymmetric SB transceivers incorporating a 12-Gb/s PAM-4 forward channel and a 125-Mb/s PAM-2 back channel are presented and demonstrated. The proposed wide linear range (WLR) hybrid combined with a gmC low-pass filter and an echo canceller effectively suppresses the outbound signals by more than 24dB. In addition, linear range enhancer which forms a gain attenuator with WLR hybrid breaks the trade-off between the linearity and the amplitude of the PAM-4 signal. The SB transceiver chips are separately fabricated in 40-nm CMOS technology. Using above design techniques, both PAM-4 and PAM-2 SB transceivers achieve BER less than 1E-12 over a 5-m channel (15.9 dB channel loss), consuming 78.4 mW. The overall transceivers achieve an FoM of 0.41 pJ/b/dB and eye margin (at BER of 1E-12) of 0.15 UI and 0.57 UI for the forward PAM-4 and back PAM-2 signals, respectively, under SB communication. This is the best eye margin compared to the prior art SB transceivers with an FoM less than 0.5.CHAPTER 1 INTRODUCTION 1 1.1 MOTIVATION 1 1.2 DISSERTATION ORGANIZATION 4 CHAPTER 2 BACKGROUND ON AUTOMOTIVE CAMERA LINK 6 2.1 OVERVIEW 6 2.2 SYSTEM REQUIREMENTS 10 2.2.1 CHANNEL 10 2.2.2 POWER OVER DIFFERENTIAL LINE (PODL) 12 2.2.3 AC COUPLING AND DC BALANCE CODE 15 2.2.4 SIMULTANEOUS BIDIRECTIONAL COMMUNICATION 18 2.2.4.1 HYBRID 18 2.2.4.2 ECHO CANCELLER 20 2.2.5 ADAPTIVE RECEIVE EQUALIZATION 22 CHAPTER 3 AREA AND POWER EFFICIENT 10B6Q ENCODER FOR DC BALANCE 25 3.1 INTRODUCTION 25 3.2 PRIOR WORKS 28 3.3 PROPOSED AREA- AND POWER-EFFICIENT 10B6Q PAM-4 CODER 30 3.4 DESIGN OF THE 10B6Q CODE 33 3.4.1 PAM-4 DC BALANCE 35 3.4.2 PAM-4 TRANSITION DENSITY 35 3.4.3 10B6Q DECODER 37 3.5 IMPLEMENTATION AND MEASUREMENT RESULTS 40 CHAPTER 4 PAM-4 TRANSMITTER AND ADAPTIVE RECEIVER WITH FIXED DATA AND THRESHOLD LEVELS 45 4.1 INTRODUCTION 45 4.2 PRIOR WORKS 47 4.3 ARCHITECTURE AND IMPLEMENTATION 49 4.2.1 PAM-4 TRANSMITTER 49 4.2.2 PAM-4 ADAPTIVE RECEIVER 52 4.3 MEASUREMENT RESULTS 62 CHAPTER 5 ASYMMETRIC SIMULTANEOUS BIDIRECTIONAL TRANSCEIVERS USING WIDE LINEAR RANGE HYBRID 68 5.1 INTRODUCTION 68 5.2 PRIOR WORKS 70 5.3 WIDE LINEAR RANGE (WLR) HYBRID 75 5.3 IMPLEMENTATION 78 5.3.1 SERIALIZER (SER) DESIGN 78 5.3.2 DESERIALIZER (DES) DESIGN 79 5.4 HALF CIRCUIT ANALYSIS OF WLR HYBRID AND LRE 82 5.5 MEASUREMENT RESULTS 88 CHAPTER 6 CONCLUSION 97 BIBLIOGRAPHY 99 초 록 106박