Integrated Circuit and System Design for Cognitive Radio and Ultra-Low Power Applications

The ubiquitous presence of wireless and battery-powered devices is an inseparable and invincible feature of our modern life. Meanwhile, the spectrum aggregation, and limited battery capacity of handheld devices challenge the exploding demand and growth of such radio systems. In this work, we try to present two separate solutions for each case; an ultra-wideband (UWB) receiver for Cognitive Radio (CR) applications to deal with spectrum aggregation, and an ultra-low power (ULP) receiver to enhance battery life of handheld wireless devices. Limited linearity and LO harmonics mixing are two major issues that ultra-wideband receivers, and CR in particular, are dealing with. Direct conversion schemes, based on current-driven passive mixers, have shown to improve the linearity, but unable to resolve LO harmonic mixing problem. They are usually limited to 3rd, and 5th harmonics rejection or require very complex and power hungry circuitry for higher number of harmonics. This work presents a heterodyne up-down conversion scheme in 180 nm CMOS technology for CR applications (54-862 MHz band) that mitigates the harmonic mixing issue for all the harmonics, while by employing an active feedback loop, a comparable to the state-of-the art IIP3 of better than +10 dBm is achieved. Measurements show an average NF of 7.5 dB when the active feedback loop is off (i.e. in the absence of destructive interference), and 15.5 dB when the feedback loop is active and a 0 dBm interferer is applied, respectively. Also, the second part of this work presents an ultra-low power super-regenerative receiver (SRR) suitable for OOK modulation and provides analytical insight into its design procedure. The receiver is fabricated in 40 nm CMOS technology and operates in the ISM band of 902-928 MHz. Binary search algorithm through Successive Approximation Register (SAR) architecture is being exploited to calibrate the internally generated quench signal and the working frequency of the receiver. Employing an on-chip inductor and a single-ended to differential architecture for the input amplifier has made the receiver fully integrable, eliminating the need for external components. A power consumption of 320 µW from a 0.65 V supply results in an excellent energy efficiency of 80 pJ/b at 4 Mb/s data rate. The receiver also employs an ADC that enables soft-decisioning and a convenient sensitivity-data rate trade-off, achieving sensitivity of -86.5, and -101.5 dBm at 1000 and 31.25 kbps data rate, respectivel

Integrated Circuit and System Design for Cognitive Radio and Ultra-Low Power Applications

The ubiquitous presence of wireless and battery-powered devices is an inseparable and invincible feature of our modern life. Meanwhile, the spectrum aggregation, and limited battery capacity of handheld devices challenge the exploding demand and growth of such radio systems. In this work, we try to present two separate solutions for each case; an ultra-wideband (UWB) receiver for Cognitive Radio (CR) applications to deal with spectrum aggregation, and an ultra-low power (ULP) receiver to enhance battery life of handheld wireless devices. Limited linearity and LO harmonics mixing are two major issues that ultra-wideband receivers, and CR in particular, are dealing with. Direct conversion schemes, based on current-driven passive mixers, have shown to improve the linearity, but unable to resolve LO harmonic mixing problem. They are usually limited to 3rd, and 5th harmonics rejection or require very complex and power hungry circuitry for higher number of harmonics. This work presents a heterodyne up-down conversion scheme in 180 nm CMOS technology for CR applications (54-862 MHz band) that mitigates the harmonic mixing issue for all the harmonics, while by employing an active feedback loop, a comparable to the state-of-the art IIP3 of better than +10 dBm is achieved. Measurements show an average NF of 7.5 dB when the active feedback loop is off (i.e. in the absence of destructive interference), and 15.5 dB when the feedback loop is active and a 0 dBm interferer is applied, respectively. Also, the second part of this work presents an ultra-low power super-regenerative receiver (SRR) suitable for OOK modulation and provides analytical insight into its design procedure. The receiver is fabricated in 40 nm CMOS technology and operates in the ISM band of 902-928 MHz. Binary search algorithm through Successive Approximation Register (SAR) architecture is being exploited to calibrate the internally generated quench signal and the working frequency of the receiver. Employing an on-chip inductor and a single-ended to differential architecture for the input amplifier has made the receiver fully integrable, eliminating the need for external components. A power consumption of 320 µW from a 0.65 V supply results in an excellent energy efficiency of 80 pJ/b at 4 Mb/s data rate. The receiver also employs an ADC that enables soft-decisioning and a convenient sensitivity-data rate trade-off, achieving sensitivity of -86.5, and -101.5 dBm at 1000 and 31.25 kbps data rate, respectivel

Energy-Efficient Wireless Circuits and Systems for Internet of Things

As the demand of ultra-low power (ULP) systems for internet of thing (IoT) applications has been increasing, large efforts on evolving a new computing class is actively ongoing. The evolution of the new computing class, however, faced challenges due to hard constraints on the RF systems. Significant efforts on reducing power of power-hungry wireless radios have been done. The ULP radios, however, are mostly not standard compliant which poses a challenge to wide spread adoption. Being compliant with the WiFi network protocol can maximize an ULP radio’s potential of utilization, however, this standard demands excessive power consumption of over 10mW, that is hardly compatible with in ULP systems even with heavy duty-cycling. Also, lots of efforts to minimize off-chip components in ULP IoT device have been done, however, still not enough for practical usage without a clean external reference, therefore, this limits scaling on cost and form-factor of the new computer class of IoT applications. This research is motivated by those challenges on the RF systems, and each work focuses on radio designs for IoT applications in various aspects. First, the research covers several endeavors for relieving energy constraints on RF systems by utilizing existing network protocols that eventually meets both low-active power, and widespread adoption. This includes novel approaches on 802.11 communication with articulate iterations on low-power RF systems. The research presents three prototypes as power-efficient WiFi wake-up receivers, which bridges the gap between industry standard radios and ULP IoT radios. The proposed WiFi wake-up receivers operate with low power consumption and remain compatible with the WiFi protocol by using back-channel communication. Back-channel communication embeds a signal into a WiFi compliant transmission changing the firmware in the access point, or more specifically just the data in the payload of the WiFi packet. With a specific sequence of data in the packet, the transmitter can output a signal that mimics a modulation that is more conducive for ULP receivers, such as OOK and FSK. In this work, low power mixer-first receivers, and the first fully integrated ultra-low voltage receiver are presented, that are compatible with WiFi through back-channel communication. Another main contribution of this work is in relieving the integration challenge of IoT devices by removing the need for external, or off-chip crystals and antennas. This enables a small form-factor on the order of mm3-scale, useful for medical research and ubiquitous sensing applications. A crystal-less small form factor fully integrated 60GHz transceiver with on-chip 12-channel frequency reference, and good peak gain dual-mode on-chip antenna is presented.PHDElectrical and Computer EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/162975/1/jaeim_1.pd

Millimeter-Scale and Energy-Efficient RF Wireless System

This dissertation focuses on energy-efficient RF wireless system with millimeter-scale dimension, expanding the potential use cases of millimeter-scale computing devices. It is challenging to develop RF wireless system in such constrained space. First, millimeter-sized antennae are electrically-small, resulting in low antenna efficiency. Second, their energy source is very limited due to the small battery and/or energy harvester. Third, it is required to eliminate most or all off-chip devices to further reduce system dimension. In this dissertation, these challenges are explored and analyzed, and new methods are proposed to solve them. Three prototype RF systems were implemented for demonstration and verification. The first prototype is a 10 cubic-mm inductive-coupled radio system that can be implanted through a syringe, aimed at healthcare applications with constrained space. The second prototype is a 3x3x3 mm far-field 915MHz radio system with 20-meter NLOS range in indoor environment. The third prototype is a low-power BLE transmitter using 3.5x3.5 mm planar loop antenna, enabling millimeter-scale sensors to connect with ubiquitous IoT BLE-compliant devices. The work presented in this dissertation improves use cases of millimeter-scale computers by presenting new methods for improving energy efficiency of wireless radio system with extremely small dimensions. The impact is significant in the age of IoT when everything will be connected in daily life.PHDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttps://deepblue.lib.umich.edu/bitstream/2027.42/147686/1/yaoshi_1.pd

A Low-Power BFSK/OOK Transmitter for Wireless Sensors

In recent years, significant improvements in semiconductor technology have allowed consistent development of wireless chipsets in terms of functionality and form factor. This has opened up a broad range of applications for implantable wireless sensors and telemetry devices in multiple categories, such as military, industrial, and medical uses. The nature of these applications often requires the wireless sensors to be low-weight and energy-efficient to achieve long battery life. Among the various functions of these sensors, the communication block, used to transmit the gathered data, is typically the most power-hungry block. In typical wireless sensor networks, transmission range is below 10 meters and required radiated power is below 1 milliwatt. In such cases, power consumption of the frequency-synthesis circuits prior to the power amplifier of the transmitter becomes significant. Reducing this power consumption is currently the focus of various research endeavors. A popular method of achieving this goal is using a direct-modulation transmitter where the generated carrier is directly modulated with baseband data using simple modulation schemes. Among the different variations of direct-modulation transmitters, transmitters using unlocked digitally-controlled oscillators and transmitters with injection or resonator-locked oscillators are widely investigated because of their simple structure. These transmitters can achieve low-power and stable operation either with the help of recalibration or by sacrificing tuning capability. In contrast, phase-locked-loop-based (PLL) transmitters are less researched. The PLL uses a feedback loop to lock the carrier to a reference frequency with a programmable ratio and thus achieves good frequency stability and convenient tunability. This work focuses on PLL-based transmitters. The initial goal of this work is to reduce the power consumption of the oscillator and frequency divider, the two most power-consuming blocks in a PLL. Novel topologies for these two blocks are proposed which achieve ultra-low-power operation. Along with measured performance, mathematical analysis to derive rule-of-thumb design approaches are presented. Finally, the full transmitter is implemented using these blocks in a 130 nanometer CMOS process and is successfully tested for low-power operation

Integrated Filters and Couplers for Next Generation Wireless Tranceivers

The main focus of this thesis is to investigate the critical nonlinear distortion issues affecting RF/Microwave components such as power amplifiers (PA) and develop new and improved solutions that will improve efficiency and linearity of next generation RF/Microwave mobile wireless communication systems. This research involves evaluating the nonlinear distortions in PA for different analog and digital signals which have been a major concern. The second harmonic injection technique is explored and used to effectively suppress nonlinear distortions. This method consists of simultaneously feeding back the second harmonics at the output of the power amplifier (PA) into the input of the PA. Simulated and measured results show improved linearity results. However, for increasing frequency bandwidth, the suppression abilities reduced which is a limitation for 4G LTE and 5G networks that require larger bandwidth (above 5 MHz). This thesis explores creative ways to deal with this major drawback. The injection technique was modified with the aid of a well-designed band-stop filter. The compact narrowband notch filter designed was able to suppress nonlinear distortions very effectively when used before the PA. The notch filter is also integrated in the injection technique for LTE carrier aggregation (CA) with multiple carriers and significant improvement in nonlinear distortion performance was observed. This thesis also considers maximizing efficiency alongside with improved linearity performance. To improve on the efficiency performance of the PA, the balanced PA configuration was investigated. However, another major challenge was that the couplers used in this configuration are very large in size at the desired operating frequency. In this thesis, this problem was solved by designing a compact branch line coupler. The novel coupler was simulated, fabricated and measured with performance comparable to its conventional equivalent and the coupler achieved substantial size reduction over others. The coupler is implemented in the balanced PA configuration giving improved input and output matching abilities. The proposed balanced PA is also implemented in 4G LTE and 5G wireless transmitters. This thesis provides simulation and measured results for all balanced PA cases with substantial efficiency and linearity improvements observed even for higher bandwidths (above 5 MHz). Additionally, the coupler is successfully integrated with rectifiers for improved energy harvesting performance and gave improved RF-dc conversion efficienc

無線センサネットワークのための超低消費電力と高感度CMOS RF受信機に関する研究

Wireless sensor networks (WSN) have been applied in wide range of applications and proved the more and more important contribution in the modern life. In order to evaluate a WSN, many metrics are considered such as cost, latency, power or quality of service. However, since the sensor nodes are usually deployed in large physical areas and inaccessible locations, the battery change becomes impossible. In this scenario, the power consumption is the most important metric. In a sensor node, the RF receiver is one of the communication devices, which consume a vast majority of power. Therefore, this thesis studies ultra low power RF receivers for the long lifetime of the sensor nodes. Currently, the WSNs use various frequency bands. However, for low power target, the sub-GHz frequency bands are preferred. In this study, ultra-low power 315 MHz and 920 MHz receivers will be proposed for short-range applications and long-range applications of the WSNs respectively. To achieve ultra-low power target, the thesis considers some issues in architecture, circuit design and fabrication technology for suitable choices. After considering different receiver architectures, the RF detection receiver with the On-Off-Keying (OOK) modulation is chosen. Then the thesis proposes solutions to reduce power consumption and concurrently guarantee high sensitivity for the receivers so that they can communicate at adequate distances for both short and long-range applications. First, a 920 MHz OOK receiver is designed for the long-range WSN applications. Typically, the RF amplifiers and local oscillators consume the most of power of RF receivers. In the RF detection receivers, the local oscillators are eliminated, however, the power consumption of the RF amplifiers is still dominant. By reducing the RF gain or removing the RF amplifier, the power consumption of the receivers can be reduced drastically. However, in this case the sensitivity is very limited. In order to overcome the trade-off between power consumption and sensitivity, the switched bias is applied to the RF amplifiers to reduce their power consumption substantially while guaranteeing high RF gain before RF detection. As a result, the receiver consumes only 53 W at 0.6 V supply with -82 dBm sensitivity at 10 kbps data rate. Next, an OOK receiver operating at 315 MHz for the short-range WSN applications with low complexity is proposed. In this receiver, the RF amplifier is controlled to operate intermittently for power reduction. Furthermore, taking advantage of the low carrier frequency, a comparator is used to convert the RF signal to a rail-to-rail stream and then data is demodulated in the digital domain. Therefore, no envelope detector or baseband amplifiers is required. The architecture of the receiver is verified by using discrete RF modules and FPGAs before it is designed on CMOS technology. By simulation with the physical layout, the 315 MHz OOK receiver consumes 27.6 W at 200 kbps and achieves -76.4 dBm sensitivity. Finally, the Synchronized-OOK (S-OOK) modulation scheme is proposed and then an S-OOK receiver operating in the 315 MHz frequency is developed to reduce power consumption more deeply. The S-OOK signal contains not only data but also clock information. By generating a narrow window, the RF front-end is enabled to receive signal only in a short period, therefore, power consumption of the receiver is reduced further. In addition, thank to the clock information contained in the input signal, the data and corresponding clock are demodulated simultaneously without a clock and data recovery circuit. The architecture of the S-OOK receiver is also verified by using discrete RF modules and FPGAs, then VLSI design is carried out. Physical layout simulation shows that the receiver can achieve -76.4 dBm sensitivity, consumes 8.39 W, 4.49 W, 1.36 W at 100 kbps, 50 kbps and 10 kbps respectively. In conclusion, with the objective is to look for solutions to minimize power consumption of receivers for extending the lifetime of sensor nodes while guaranteeing high sensitivity, this study proposed novel receiver architectures, which help reduce power consumption significantly. If using the coin battery CR2032 for power supply, the 920 MHz OOK receiver can work continuously in 1.45 years with communication distance of 259 meters; the 315 MHz OOK receivers can work continuously in 2.8 years with approximately 19 meters communication distance in free space. Whereas, the 315 MHz S-OOK receiver with the minimum power consumption of 1.36 W is suitable for batteryless sensor nodes.電気通信大学201

Advanced CMOS Integrated Circuit Design and Application

The recent development of various application systems and platforms, such as 5G, B5G, 6G, and IoT, is based on the advancement of CMOS integrated circuit (IC) technology that enables them to implement high-performance chipsets. In addition to development in the traditional fields of analog and digital integrated circuits, the development of CMOS IC design and application in high-power and high-frequency operations, which was previously thought to be possible only with compound semiconductor technology, is a core technology that drives rapid industrial development. This book aims to highlight advances in all aspects of CMOS integrated circuit design and applications without discriminating between different operating frequencies, output powers, and the analog/digital domains. Specific topics in the book include: Next-generation CMOS circuit design and application; CMOS RF/microwave/millimeter-wave/terahertz-wave integrated circuits and systems; CMOS integrated circuits specially used for wireless or wired systems and applications such as converters, sensors, interfaces, frequency synthesizers/generators/rectifiers, and so on; Algorithm and signal-processing methods to improve the performance of CMOS circuits and systems

Low-Power Integrated Circuits For Biomedical Applications

With thousands new cases of spinal cord injury reported everyday, many people suffer from paralysis and loss of sensation in both legs. Beside the healthcare costs, such a state severely deteriorates the patients' quality of life and may even lead to additional medical conditions. Therefore, there is a growing need for cyber-physical systems to restore the walking ability through bypassing the damaged spinal cord. This goal can be achieved by monitoring and processing patient's brain signals to enable brain-directed control of prosthetic legs. Among several existing methods to record brain signals, electrocorticography (ECoG) has gained popularity due to being robust to motion artifacts, having high spatial resolution and signal to noise ratio, being moderately invasive and the possibility of chronic implantation of recording grids with no or minor scar tissue formation. The latest property is of particular importance for the whole system to be a viable fully implantable solution. Furthermore, the implanted system has to operate independently with no or minimal need of external hardware (e.g. a bulky personal computer) to be individually and socially accepted. To implement a fully implantable system, low-power and miniaturized electronics are needed to reduced heat generation, increase battery life-time and be minimally intrusive. These requirements indicate that many of the system's components should be custom-designed to integrated as much functionality as possible in a given real estate. This thesis presents silicon tested prototypes of several building blocks for the envisioned system, namely, ultra low-power brain signal acquisition front-ends, a low-power and inductorless MedRadio transceiver, and a fast start-up crystal oscillator. Brain signal acquisition front-ends provide low noise amplification of weak ECoG biosignals. MedRadio transceiver enables communication between the implant and end effectors or base station (e.g. prosthetic legs or desktop computer). Crystal oscillator generates the reference signal for other system's components such as analog to digital converter. Novel techniques to improve important performance parameters (power consumption, low noise operation and interference resilience) have been introduced. Electrical, in-vitro and in-vivo experimental measurements have verified the functionality and performance of each design

5 G Systems

Communication is an interactive dynamic, information that is continually at change. Especially in the eld of telecommunications, as time passed and with the appearance of First Generation, that allowed us to give mobility to Analog Communication...La comunicación es una dinámica interactiva debido a la constante evolución de la información. Especialmente en el campo de las telecomunicaciones, con el paso del tiempo y con la aparición de la Primera Generación y que nos permitió dar movilidad a la Comunicación Analógica..