Multilevel Modulation and Transmission in VCSEL-based Short-range Fiber Optic Links

As the demand for ever higher throughput short-range optical links is growing, research and industry associations have shown increased interest in multilevel modulation formats, such as the four leveled pulse amplitude modulation, referred to as 4-PAM. As on-off keying (OOK) persists to be the choice for low latency applications, for example high performance computing, datacenter operators see 4-PAM as the next format to succeed current OOK-based optical interconnects. Throughput can be increased in many ways: parallel links can be deployed, multicore fibers can be used or more efficient modulation formats with digital signal processing is an alternative. Therefore, to improve link data rates, the introduction of new modulation formats and pre-emphasis are primarily considered in this thesis. In a bandwidth-limited link, turning towards spectrally efficient formats is one of the methods to\ua0 overcome the bandwidth requirements of OOK. Such are the considerations when opting for 3-PAM or 4-PAM schemes. Both require lower bandwidth than OOK and are potential candidates in such scenarios. 4-PAM provides double spectral efficiency and double data rate at the same symbol rate as on-off keying, but, as with any technology transition, new challenges emerge, such as a higher SNR requirement, a lower tolerance to VCSEL nonlinearities and skewing of the signal in the time domain. 3-PAM could potentially be an in-between solution, as it requires 33% less bandwidth than OOK and is less sensitive to VCSEL dynamics which could impair the transmission. A study is presented where 3-PAM has outperformed both OOK and 4-PAM in the same link. Detailed investigation of legacy 25G class VCSELs has shown that devices with moderate damping are suitable for the transition to 4-PAM. The pre-emphasis of signals is a powerful tool to increase link bandwidth at the cost of modulation amplitude. This has been investigated in this thesis for on-offkeying and has shown 9% and 27% increase in bit rate for error-free operation with two pre-emphasis approaches. Similarly, pre-emphasis of a 4-PAM electrical signals has enabled 71.8 Gbps transmission back-to-back with lightweight forward error correction and 94 Gbps net data rate was achieved with the same pre-emphasis and post-processing using an offline least-mean-square equalizer

A Novel Equalizer for 112 Gb/s CAP-Based Data Transmission over 150 m MMF Links

© 1983-2012 IEEE. In this paper a novel feedforward and decision feedback equalizer is proposed for the first time for use in short-reach high-speed communication links based on carrierless amplitude and phase (CAP) modulation. The proposed new equalizer mitigates crosstalk between the in-phase (I-) and quadrature (Q-) channels resulting from the non-linear phase response of the link enabling significant improvement in the link performance when operating at high data rates. The structure of this novel equalizer is introduced, its operation is described, and simulation and experimental studies on short-reach high-speed MMF links using 850 nm multimode VCSELs are presented. Data transmission tests are carried out over 150 m of OM4 MMF at 112 Gb/s using CAP modulation and the proposed CAP equalizer, and a bit-error-rate (BER) within the hard-decision forward error-correction (HD-FEC) threshold of 3.8 × 10-3 is achieved. The link is also tested when a conventional equalizer is used instead of the CAP equalizer and when adaptive discrete multitone (DMT) modulation is applied. The performance of the link is compared for these different transmission schemes and it is shown that the use of the novel equalizer and CAP modulation outperforms the other two schemes. The proposed equalizer can be implemented with low additional complexity, providing a potential cost-effective solution enabling >100 Gb/s single-lane data transmission in short-reach MMF-based links.UK EPSRC via the Terabit Bidirectional Multi-user Optical Wireless System project (TOWS) (EP/S016570/1)

VCSEL and Integration Techniques for Wavelength-Multiplexed Optical Interconnects

GaAs-based vertical-cavity surface-emitting lasers (VCSELs) are dominating short-reach optical interconnects (OIs) due to their high modulation speed, low power consumption, circular output beam and low fabrication cost. Such OIs provide the high bandwidth connectivity needed for interconnecting servers and switches in data centers. With the rapidly increasing use of Internet-based applications and services, higher bandwidth connectivity and higher aggregate capacity VCSEL-based OIs are needed. Until now, this has been achieved mostly through an increase of the lane rate by higher speed VCSELs and higher order modulation formats. Furthermore, spatial-division-multiplexing has proven effective for increasing the aggregate capacity. Much higher capacity can be achieved by multiple wavelengths per fiber, known as wavelength-divisionmultiplexing (WDM). Moreover, smaller footprint and higher bandwidth density WDM transceivers can be built using monolithic multi-wavelength VCSEL arrays with densely spaced VCSELs. This requires a VCSEL technology where the wavelength of individual VCSELs can be precisely set in a post-epitaxial growth fabrication process and a photonic integrated circuit (PIC) for multiplexing and fiber coupling. Flip-chip integration over grating couplers (GCs) is considered for interfacing VCSELs with waveguides on the PIC. In this thesis, an intra-cavity phase tuning technique is demonstrated for setting the resonance wavelength of VCSELs in a monolithic array with an accuracy in spacing of <1 nm. Uniform performance over the array is achieved by spectral matching and balancing of mirror reflectances, optical confinement factor and optical gain. Single transverse and polarization mode VCSELs, as required for flip-chip integration over GCs, with a record output power of 6 mW are also demonstrated.Finally, an investigation of angled flip-chip integration of a VCSEL over a GC on a silicon photonic integrated circuit (Si-PIC) is presented. Dependencies of coupling efficiency and optical feedback on flip-chip angle and size of the VCSEL die are studied using numerical FDTD simulations. Moreover, flip-chip integration of a VCSEL over a GC on a Si-PIC is experimentally demonstrated. The insertion loss from the VCSEL at the input GC to a singlemode fiber, multimode fiber or flip-chip integrated photodetector over the output GC was measured and quantified. The latter forms an on-PIC optical link

Directly Phase Modulated Transmitters and Coherent Recivers for Future Passive Optical Networks (PON)

En los últimos años, el tráfico de dato transmitido en las redes ópticas de acceso ha crecido exponencialmente debido a nuevos servicios como pueden ser la computación en la nube, el video online, la realidad virtual y aumentada, el internet de las cosas (IoT) y la convergencia entre las redes ópticas y redes inalámbricas en el paradigma del 5G. Estos nuevos servicios endurecen los requerimientos de las redes ópticas de acceso, como pueden ser unas tasas de datos más altas, un mayor alcance y un mayor número de usuarios. Para abordar estos requerimientos, esta tesis ha investigado, desarrollado y analizado nuevas tecnologías para transmisores y receptores orientadas a los dos tipos de redes ópticas de acceso que la comunidad científica ha identificado como posibles candidatas. Estos dos tipos de redes ópticas son las redes uDWDM y las redes TWDM como las redes NG-PON2 y sus evoluciones.Las redes uDWDM están basadas en la transmisión de tasas de datos relativamente bajas, por debajo de 2.5 Gbps, que son dedicadas en su totalidad a los usuarios finales. Estas tasas de datos relativamente bajas son multiplexadas en longitud de onda usando intervalos frecuenciales estrechos, del orden de 12.5 GHz o 6.25 GHz. En esta tesis, los transmisores modulados directamente en fase se han propuesto como posibles candidatos para estas redes uDWDM. En concreto, se han propuesto un DFB modulado directamente en fase con una tasa de datos de 1 Gbps; un RSOA bombeado por un VCSEL y modulado directamente en fase con una tasa de datos de 1 Gbps; y un VCSEL modulado directamente en fase con una tasa de datos de 1.25 Gbps y 2.5 Gbps. Estas señales moduladas directamente en fase son recibidas con un receptor heterodino con un único fotodiodo (PD) para mantener el coste tan bajo como sea posible. La combinación de estos transmisores modulados directamente en fase con el receptor heterodino con un único PD ha sido probada como unos candidatos muy prometedores para las redes ópticas de acceso basadas en redes uDWDM. Estas combinaciones proveen sensibilidades que varían entre -39.5 dBm y -52 dBm, que se traducen en balances de potencia que van desde 38.5 dB a 51 dB y por lo tanto en ratios de división o número de usuarios de entre 128 y 1024 después de una transmisión de 50 km a través de fibra monomodo estándar (SSMF).Además, los links de 1 Gbps formados por la modulación directa de DFBs o de RSOAs bombeados por VCSELs y el receptor heterodino con un único PD son usados como enlace de subida en canales bidireccionales. Estos enlaces de subida son combinados con enlaces de bajada basados en Nyquist-DPSK generada con un MZM y recibidos con un receptor heterodino de un único PD. Como parte de análisis de los canales bidireccionales, se ha analizado el estudio de la viabilidad del uso de LOs de bajo coste, como DFBs o VCSELs, en los receptores heterodinos con un único PD. Estos canales bidireccionales son también unos candidatos prometedores para las futuras redes uDWDM, ya que en esta tesis se ha probado que pueden proveer enlaces full-duplex de 1 Gbps usando intervalos frecuenciales tan pequeños como 6.25 GHz o 5 GHz. Estos canales bidireccionales tienen balances de potencia que van desde 37 dB a 42 dB y tienen posibles ratios de división de 128 o 256 después de una transmisión de 50 km a través de SSMF.Esta tesis también ha investigado y desarrollado receptores quasicoherentes para redes NG-PON2 y sus evoluciones. Este tipo de redes están basadas en altas tasas de datos, como 10 Gbps para redes NG-PON2 y 25 Gbps para las futuras evoluciones de NG-PON2, en entornos multi longitud de onda donde los usuarios son multiplexados en tiempo y longitud de onda (TWDM). El receptor quasicoherente usa la amplificación coherente gracias a la recepción heterodina y por tanto la sensibilidad del receptor es mejorada en comparación con los esquemas de detección directa. El receptor quasicoherente es independiente a la polarización, lo cual es una característica importante para los receptores coherentes. Además, el receptor quasicoherente permite seleccionar el canal de trabajo sin la necesidad de filtros ópticos y es un receptor independiente de la longitud de onda debido a que el canal de trabajo se puede elegir ajustando la longitud de onda del LO. El receptor quasicoherente de 10 Gbps muestra una sensibilidad -35.2 dBm y por tanto permite un balance de potencias de 35.64 dB y un ratio de división de 128 después de una transmisión de 40 km a través de SSMF.La combinación del receptor quasicoherente con un ecualizador FFE/DFE permite combatir la dispersión cromática de la banda C y conseguir un link de 25 Gbps con un alcance de 20 km a través de SSMF. El receptor quasicoherente a 25 Gbps con ecualización FFE/DFE muestra una mejor sensibilidad de -30.5 dBm con el llamado ecualizador de altas prestaciones, lo que lleva a un balance de potencias de25 dB. Si se utilizada el llamado ecualizador de baja complejidad, la sensibilidad cae a -27 dBm y el balance de potencias cae a 23 dBm. En ambos casos, el receptor quasicoherente a 25 Gbps con ecualización FFE/DFE permite un ratio de división de 32 después de una transmisión de 20 km a través de SSMF.En conclusión, esta tesis ha presentado transmisores (DFB, RSOA y VCSEL) modulados directamente en fase combinados con un receptor heterodino con un único PD como potenciales candidatos para las redes uDWDM. Esta tesis también ha presentados los receptores quasicoherentes como unos candidatos muy prometedores para las redes NG-PON2 y sus futuras evoluciones.<br /

1060 nm GaAs VCSELs for Extended Reach Optical Interconnects in Data Centers

The data centers of today are increasing in size and are built to accommodate strong data traffic demands while providing sustainably by having clients sharing resources under one roof. Their massive scale puts pressure on the server network topology and has incited a need for data transmission links that are energy efficient and capable to operate at high bit rates with reach up to a few kilometers. Optical interconnects (OIs) offer large bandwidth and low attenuation at long distances, and are therefore suitable for this task. The most commonly used OIs, with 850 nm GaAs-based vertical-cavity surface-emitting lasers (VCSELs) and multi-mode fiber (MMF), have a 25 Gb/s reach that is limited to a few hundred meters. However, the fiber chromatic dispersion and attenuation that limit the OI reach can be reduced significantly by increasing the wavelength of this very same technology. The upper limit of the GaAs-based VCSEL technology, with strained InGaAs quantum wells (QWs), is about 1100 nm.With further improved OI performance, new hyperscale data center topologies can be realized and explored. This will lead to many more possible solutions in traffic engineering as well as for power management. 1060 nm VCSELs could open up for lane rates of 10, 25 and possibly 50 Gb/s over distances up to 2 km and help reach the Tb/s link speed aim of the Ethernet standard.In this work we show that the 1060 nm GaAs VCSEL is a suitable light source for long-reach OIs by demonstrating its overall stable performance and capability of error-free data transmission up to 50 Gb/s back-to-back and 25 Gb/s over 1 km of MMF. These results stem from careful VCSEL design, including strained InGaAs QWs with GaAsP barriers, doped AlGaAs distributed Bragg reflectors, a short op-tical cavity and multiple oxide layers. We also show that the fabrication of such a device poses no increase in complexity and can be realized using standard processing techniques

High Speed Optical Links Using CAP Modulation and Novel Equalisation Techniques

High speed optical links suffer from inter-symbol-interference (ISI) due to their limited bandwidth. Equalisation is typically used to mitigate ISI and therefore improve the link capacity. This dissertation explores novel equalisation techniques for carrierless amplitude and phase (CAP) modulation based optical communication systems including OM4 based and plastic optical fibre (POF) based links. An 850 nm VCSEL based OM4 link using CAP-16 scheme is studied. For the first time, the CAP equaliser, is proposed to mitigate both crosstalk channel interference (CCI) and ISI in the link at the receiver side. Performance comparisons are studied between the CAP-16 scheme using CAP equaliser and a conventional equaliser, pulse amplitude modulation (PAM-4) scheme, and discrete multitone (DMT) scheme. CAP based data transmission of 112 Gb/s is achieved over 150 m OM4 fibre with this novel equaliser, while the conventional equaliser can only support over 1 m OM4 fibre and fails to recover the signals at the same data rate. In addition, this novel equaliser provides a 1.2 dB and 1.7 dB improvement in receiver sensitivity over PAM-4 and DMT schemes, respectively, at 112 Gb/s over 100 m OM4 fibre. A novel pre-CAP-equaliser solving CCI at the transmitter side is also proposed. Data transmission of 56 Gb/s over 100 m OM4 fibre is reported experimentally with an improvement of 0.7 dB in receiver sensitivity compared to using the CAP equaliser at the receiver side. A simulation study shows a 2 dB improvement in receiver sensitivity at 112 Gb/s over 100 m OM4 fibre. Furthermore, an artificial neural network (ANN) equaliser in conjunction with the CAP equaliser structure is explored in a VCSEL based OM4 fibre link in order to further mitigate the nonlinear impairments. For 112 Gb/s data transmission over 100 m OM4 fibre, a 2.4 dB improvement of receiver sensitivity is achieved compared to the CAP equaliser. In addition to the electrical equalisers, a monolithically integrated silicon optical equaliser consisting of three taps is used for 50 Gb/s data transmission. After 10 km standard single mode fibre (SSMF), error free eye diagrams at the receiver are demonstrated. A μLED based POF link based on an APD receiver is also investigated with the CAP equaliser at the receiver side. Data transmission rates of 4 Gb/s over 25 m and 5 Gb/s over 10 m POF links are demonstrated with this equaliser while the conventional equaliser can only support 4 Gb/s over 10 m and fails to recover the signals for 5 Gb/s data transmission

대역폭 증대 기술을 이용한 전력 효율적 고속 송신 시스템 설계

학위논문(박사) -- 서울대학교대학원 : 공과대학 전기·정보공학부, 2022.2. 정덕균.The high-speed interconnect at the datacenter is being more crucial as 400 Gb Ethernet standards are developed. At the high data rate, channel loss re-quires bandwidth extension techniques for transmitters, even for short-reach channels. On the other hand, as the importance of east-to-west connection is rising, the data center architectures are switching to spine-leaf from traditional ones. In this trend, the number of short-reach optical interconnect is expected to be dominant. The vertical-cavity surface-emitting laser (VCSEL) is a com-monly used optical modulator for short-reach interconnect. However, since VCSEL has low bandwidth and nonlinearity, the optical transmitter also needs bandwidth-increasing techniques. Additionally, the power consumption of data centers reaches a point of concern to affect climate change. Therefore, this the-sis focuses on high-speed, power-efficient transmitters for data center applica-tions. Before the presenting circuit design, bandwidth extension techniques such as fractionally-spaced feed-forward equalizer (FFE), on-chip transmission line, inductive peaking, and T-coil are mathematically analyzed for their effec-tiveness. For the first chip, a power and area-efficient pulse-amplitude modulation 4 (PAM-4) transmitter using 3-tap FFE based on a slow-wave transmission line is presented. A passive delay line is adopted for generating an equalizer tap to overcome the high clocking power consumption. The transmission line achieves a high slow-wave factor of 15 with double floating metal shields around the differential coplanar waveguide. The transmitter includes 4:1 multi-plexers (MUXs) and a quadrature clock generator for high-speed data genera-tion in a quarter-rate system. The 4:1 MUX utilizes a 2-UI pulse generator, and the input configuration is determined by qualitative analysis. The chip is fabri-cated in 65 nm CMOS technology and occupies an area of 0.151 mm2. The proposed transmitter system exhibits an energy efficiency of 3.03 pJ/b at the data rate of 48 Gb/s with PAM-4 signaling. The second chip presents a power-efficient PAM-4 VCSEL transmitter using 3-tap FFE and negative-k T-coil. The phase interpolators (PIs) generate frac-tionally-spaced FFE tap and correct quadrature phase error. The PAM-4 com-bining 8:1 MUX is proposed rather than combining at output driver with double 4:1 MUXs to reduce serializing power consumption. T-coils at the internal and output node increase the bandwidth and remove inter-symbol interference (ISI). The negative-k T-coil at the output network increases the bandwidth 1.61 times than without T-coil. The VCSEL driver is placed on the high VSS domain for anode driving and power reduction. The chip is fabricated in 40 nm CMOS technology. The proposed VCSEL transmitter operates up to 48 Gb/s NRZ and 64 Gb/s PAM-4 with the power efficiency of 3.03 pJ/b and 2.09 pJ/b, respec-tively.400Gb 이더넷 표준이 개발됨에 따라 데이터 센터의 고속 상호 연결이 더욱 중요해지고 있다. 높은 데이터 속도에서의 채널 손실에 의해 단거리 채널의 경우에도 송신기에 대한 대역폭 확장 기술이 필요하다. 한편, 데이터 센터 내 동-서 연결의 중요성이 높아지면서 데이터 센터 아키텍처가 기존의 아키텍처에서 스파인-리프로 전환되고 있다. 이러한 추세에서 단거리 광학 인터커넥트의 수가 점차 우세해질 것으로 예상된다. 수직 캐비티 표면 방출 레이저(VCSEL)는 일반적으로 단거리 상호 연결을 위해 사용되는 광학 모듈레이터이다. VCSEL은 낮은 대역폭과 비선형성을 가지고 있기 때문에, 광 송신기도 대역폭 증가 기술을 필요로 한다. 또한, 데이터 센터의 전력 소비는 기후 변화에 영향을 미칠 수 있는 우려 지점에 도달했다. 따라서, 본 논문은 데이터 센터 응용을 위한 고속 전력 효율적인 송신기에 초점을 맞추고 있다. 회로 설계를 제시하기 전에, 부분 간격 피드-포워드 이퀄라이저 (FFE), 온칩 전송선로, 인덕터, T-코일과 같은 대역폭 확장 기술을 수학적으로 분석한다. 첫 번째 칩은 저속파 전송선로를 기반으로 한 3-탭 FFE를 사용하는 전력 및 면적 효율적인 펄스-진폭-변조 4(PAM-4) 송신기를 제시한다. 높은 클럭 전력 소비를 극복하기 위해 이퀄라이저 탭 생성을 위해 수동소자 지연 라인을 채택했다. 전송 라인은 차동 동일평면도파관 주위에 이중 플로팅 금속 차폐를 사용하여 15의 높은 전달속도 감쇠를 달성한다. 송신기에는 4:1 멀티플렉서(MUX)와 4-위상 클럭 생성기가 포함되어 있다. 4:1 MUX는 2-UI 펄스 발생기를 사용하며, 정성 분석에 의해 입력 구성이 결정된다. 이 칩은 65 nm CMOS 기술로 제작되었으며 0.151 mm2의 면적을 차지한다. 제안된 송신기 시스템은 PAM-4 신호와 함께 48 Gb/s의 데이터 속도에서 3.03 pJ/b의 에너지 효율을 보여준다. 두 번째 칩에서는 3-탭 FFE 및 역회전 T-코일을 사용하는 전력 효율적인 PAM-4 VCSEL 송신기를 제시한다. 위상 보간기(PI)는 부분 간격 FFE 탭을 생성하고 4-위상 클럭 오류를 수정하는 데 사용된다. 직렬화 전력 소비를 줄이기 위해 출력 드라이버에서 MSB와 LSB를 두 개의 4:1 MUX를 통해 결합하는 대신 8:1 MUX를 통해 PAM-4로 결합하는 회로가 제안된다. 내부 및 출력 노드에서 T-코일은 대역폭을 증가시키고 기호 간 간섭(ISI)을 제거한다. 출력 네트워크에서 역회전 T-코일은 T-코일이 없는 경우보다 대역폭을 1.61배 증가시킨다. VCSEL 드라이버는 양극 구동 및 전력 감소를 위해 높은 VSS 도메인에 배치된다. 이 칩은 40 nm CMOS 기술로 제작되었다. 제안된 VCSEL 송신기는 각각 3.03pJ/b와 2.09pJ/b의 전력 효율로 최대 48Gb/s NRZ와 64Gb/s PAM-4까지 작동한다.ABSTRACT I CONTENTS III LIST OF FIGURES V LIST OF TABLES IX CHAPTER 1 INTRODUCTION 1 1.1 MOTIVATION 1 1.2 THESIS ORGANIZATION 5 CHAPTER 2 BACKGROUND OF HIGH-SPEED INTERFACE 6 2.1 OVERVIEW 6 2.2 BASIS OF DATA CENTER ARCHITECTURE 9 2.3 SHORT-REACH INTERFACE STANDARDS 12 2.4 ANALYSES OF BANDWIDTH EXTENSION TECHNIQUES 16 2.4.1 FRACTIONALLY-SPACED FFE 16 2.4.2 TRANSMISSION LINE 21 2.4.3 INDUCTOR 24 2.4.4 T-COIL 33 CHAPTER 3 DESIGN OF 48 GB/S PAM-4 ELECTRICAL TRANSMITTER IN 65 NM CMOS 43 3.1 OVERVIEW 43 3.2 FFE BASED ON DOUBLE-SHIELDED COPLANAR WAVEGUIDE 46 3.2.1 BASIC CONCEPT 46 3.2.2 PROPOSED DOUBLE-SHIELDED COPLANAR WAVEGUIDE 47 3.3 DESIGN CONSIDERATION ON 4:1 MUX 50 3.4 PROPOSED PAM-4 ELECTRICAL TRANSMITTER 53 3.5 MEASUREMENT 57 CHAPTER 4 DESIGN OF 64 GB/S PAM-4 OPTICAL TRANSMITTER IN 40 NM CMOS 64 4.1 OVERVIEW 64 4.2 DESIGN CONSIDERATION OF OPTICAL TRANSMITTER 66 4.3 PROPOSED PAM-4 VCSEL TRANSMITTER 69 4.4 MEASUREMENT 82 CHAPTER 5 CONCLUSIONS 88 BIBLIOGRAPHY 90 초 록 101박

Optical Microwave Signal Generation for Data Transmission in Optical Networks

The massive growth of telecommunication services and the increasing global data traffic boost the development, implementation, and integration of different networks for data transmission. An example of this development is the optical fiber networks, responsible today for the inter-continental connection through long-distance links and high transfer rates. The optical networks, as well as the networks supported by other transmission media, use electrical signals at specific frequencies for the synchronization of the network elements. The quality of these signals is usually determined in terms of phase noise. Due to the major impact of the phase noise over the system performance, its value should be minimized. The research work presented in this document describes the design and implementation of an optoelectronic system for the microwave signal generation using a vertical-cavity surface-emitting laser (VCSEL) and its integration into an optical data transmission system. Considering that the proposed system incorporates a directly modulated VCSEL, a theoretical and experimental characterization was developed based on the laser rate equations, dynamic and static measurements, and an equivalent electrical model of the active region. This procedure made possible the extraction of some VCSEL intrinsic parameters, as well as the validation and simulation of the VCSEL performance under specific modulation conditions. The VCSEL emits in C-band, this wavelength was selected because it is used in long-haul links. The proposed system is a self-initiated oscillation system caused by internal noise sources, which includes a VCSEL modulated in large signal to generate optical pulses (gain switching). The optical pulses, and the optical frequency comb associated, generate in electrical domain simultaneously a fundamental frequency (determined by a band-pass filter) and several harmonics. The phase noise measured at 10 kHz from the carrier at 1.25 GHz was -127.8 dBc/Hz, and it is the lowest value reported in the literature for this frequency and architecture. Both the jitter and optical pulse width were determined when different resonant cavities and polarization currents were employed. The lowest pulse duration was 85 ps and was achieved when the fundamental frequency was 2.5 GHz. As for the optical frequency comb, it was demonstrated that its flatness depends on the electrical modulation conditions. The flattest profiles are obtained when the fundamental frequency is higher than the VCSEL relaxation frequency. Both the electrical and the optical output of the system were integrated into an optical transmitter. The electrical signal provides the synchronization of the data generating equipment, whereas the optical pulses are employed as an optical carrier. Data transmissions at 155.52 Mb/s, 622.08 Mb/s and 1.25 Gb/s were experimentally validated. It was demonstrated that the fundamental frequency and harmonics could be extracted from the optical data signal transmitted by a band-pass filter. It was also experimentally proved that the pulsed return-to-zero (RZ) transmitter at 1.25 Gb/s, achieves bit error rates (BER) lower than $10^{-9}$ when the optical power at the receiver is higher than -33 dBm.La masificación de los servicios de telecomunicaciones y el creciente tráfico global de datos han impulsado el desarrollo, despliegue e integración de diferentes redes para la transmisión de datos. Un ejemplo de este despliegue son las redes de fibra óptica, responsables en la actualidad de la interconexión de los continentes a través de enlaces de grandes longitudes y altas tasas de transferencia. Las redes ópticas, al igual que las redes soportadas por otros medios de transmisión, utilizan señales eléctricas a frecuencias específicas para la sincronización de los elementos de red. La calidad de estas señales es determinante en el desempeño general del sistema, razón por la que su ruido de fase debe ser lo más pequeño posible. El trabajo de investigación presentado en este documento describe el diseño e implementación de un sistema optoelectrónico para la generación de señales microondas utilizando diodos láser de cavidad vertical (VCSEL) y su integración en un sistema de transmisión de datos óptico. Teniendo en cuenta que el sistema propuesto incorpora un láser VCSEL modulado directamente, se desarrolló una caracterización teórico-experimental basada en las ecuaciones de evolución del láser, mediciones dinámicas y estáticas, y un modelo eléctrico equivalente de la región activa. Este procedimiento posibilitó la extracción de algunos parámetros intrínsecos del VCSEL, al igual que la validación y simulación de su desempeño bajo diferentes condiciones de modulación. El VCSEL utilizado emite en banda C y fue seleccionado considerando que esta banda es comúnmente utilizada en enlaces de largo alcance. El sistema propuesto consiste en un lazo cerrado que inicia la oscilación gracias a las fuentes de ruido de los componentes y modula el VCSEL en gran señal para generar pulsos ópticos (conmutación de ganancia). Estos pulsos ópticos, que en el dominio de la frecuencia corresponden a un peine de frecuencia óptico, son detectados para generar simultáneamente una frecuencia fundamental (determinada por un filtro pasa banda) y varios armónicos. El ruido de fase medido a 10 kHz de la portadora a 1.25 GHz fue -127.8 dBc/Hz, y es el valor más bajo reportado en la literatura para esta frecuencia y arquitectura. Tanto la fluctuación de fase (jitter) y el ancho de los pulsos ópticos fueron determinados cuando diferentes cavidades resonantes y corrientes de polarización fueron empleadas. La duración de pulso más baja fue 85 ps y se obtuvo cuando la frecuencia fundamental del sistema era 2.5 GHz. En cuanto al peine de frecuencia óptico, se demostró que su planitud (flatness) depende de las condiciones eléctricas de modulación y que los perfiles más planos se obtienen cuando la frecuencia fundamental es superior a la frecuencia de relajación del VCSEL. Tanto la salida eléctrica como la salida óptica del sistema fueron integradas en un transmisor óptico. La señal eléctrica permite la sincronización de los equipos encargados de generar los datos, mientras que los pulsos ópticos son utilizados como portadora óptica. La transmisión de datos a 155.52 Mb/s, 622.08 Mb/s y 1.25 Gb/s fue validada experimentalmente. Se demostró que la frecuencia fundamental y los armónicos pueden ser extraídos de la señal óptica de datos transmitida mediante un filtro pasa banda. También se comprobó experimentalmente que el transmisor de datos pulsados con retorno a cero (RZ) a 1.25 Gb/s, logra tasas de error de bit (BER) menores a 10-9 cuando la potencia óptica en el receptor es mayor a -33 dBm.Gobernación de NariñoBPIN 2013000100092Doctorad