펄스에 의한 동적 부하 변조 기술을 이용한 고효율 선형 송신기에 관한 연구

학위논문 (박사)-- 서울대학교 대학원 : 전기·컴퓨터공학부, 2016. 8. 서광석.STRONG push for longer battery life time and growing thermal concerns for the modern 3G/4G mobile terminals lead to an ever-growing need for higher efficiencies from the handset power amplifiers (PAs). Furthermore, as the modulation signal bandwidth is increased and more complex modulation schemes are introduced for higher data rate, the peak-to-average power ratio (PAPR) of signals increases and the PA requires more power back-off to meet the stringent linearity requirement. Therefore, the PA design has to address the challenging task of enhancing the efficiencies in the back-off power levels. In this dissertation, dynamic load modulation (DLM) technique is investigated to boost the efficiency of a PA in the back-off output power level. This technique increases the efficiency by adjusting the PA load impedance according to the magnitude of the envelope signal. It can be categorized into two types, continuous and discrete types. Continuous-type DLM PA changes load impedance continuously by changing the capacitance of varactors used in the load matching circuit. Although the continuous modulation of the load impedance may result in significant efficiency enhancement, difficulties on integration of varactors and complexities on linearization of the PA make it difficult to be applied to the handset PA applications. Discrete-type DLM PA switches the load impedance from one value to another using RF switches. This type has the advantage in the aspect of ease of integration and simplicity in linearization compared to the continuous-type DLM PA, which make it more suited to the handset PA applications. However, the overall efficiency enhancement is quite limited since the PA does not always operate under the optimal load conditions. To overcome the limitation of the existing DLM techniques, a new method of DLM, called pulsed dynamic load modulation (PDLM), is proposed to operate the PA near the optimum impedance across a continuous back-off power range while still benefiting from the advantages offered by the discrete-type DLM PA. PDLM PA combines the concept of Class-S PA with 1-bit discrete load switching. Analytical calculation using simplified equivalent model is well matched with simulation results. To prove the proposed concept, it is implemented by designing and fabricating a prototype PDLM PA at 837 MHz using a 0.32-μm silicon-on-insulator (SOI) CMOS process. The experimental results show the overall PAE improvement for high-PAPR signals such as LTE signals. Several issues caused by the PDLM technique are also discussed such as imperfect pulse tone termination effect and output noise spectrum due to pulse tones. Improving methods are proposed through the further analysis and evaluation. The proposed PA is compared to the envelope tracking (ET) PA which is commonly used to boost efficiency at the back-off output power. Since the proposed concept is realized with low-power control circuits unlike envelope tracking, which requires high-power circuits such as dc-dc converters and linear amplifiers, the PDLM PA concept of this work can provide a potential solution for high-efficiency PAs for the future mobile terminals using wideband modulation signals.Chapter 1. Introduction 1 Chapter 2. Dynamic Load Modulation Technique 8 2.1 Introduction 8 2.2 Continuous-type dynamic load modulation PA 9 2.3 Discrete-type dynamic load modulation PA 14 2.4 Implementation example 15 2.4.1 DLM PA Structure 16 2.4.2 Linearization 23 2.4.3 Experimental Results 25 2.4.4 Conclusion 31 2.5 Limitations 32 2.6 References 33 Chapter 3. A Pulsed Dynamic Load Modulation Technique for High-Efficiency Linear Transmitters 36 3.1 Introduction 36 3.2 Operation Principle of the PDLM PA 38 3.2.1 Concept of the PDLM PA 38 3.2.2 Theoretical Analysis of the PDLM PA 41 3.3 Circuit Design 47 3.3.1 2 stage CMOS PA design 49 3.3.2 High power RF switch design 59 3.3.3 PWM signal generator and switch driver 61 3.4 Experimental Results 63 3.5 Conclusion 76 3.6 References 77 Chapter 4. Discussions 83 4.1 Operation bandwidth of the PDLM PA 83 4.2 Spectral noise reduction method 87 4.3 References 91 Chapter 5. Conclusions 94 5.1 Research Summary 94 5.2 Future Works 95 Abstract in Korean 97 Publications 99Docto

The 30/20 GHz flight experiment system, phase 2. Volume 2: Experiment system description

A detailed technical description of the 30/20 GHz flight experiment system is presented. The overall communication system is described with performance analyses, communication operations, and experiment plans. Hardware descriptions of the payload are given with the tradeoff studies that led to the final design. The spacecraft bus which carries the payload is discussed and its interface with the launch vehicle system is described. Finally, the hardwares and the operations of the terrestrial segment are presented