Design and realization of fully integrated multiband and multistandard bi-cmos sigma delta frequency synthesizer

Wireless communication has grown, exponentially, with wide range of applications offered for the customers. Among these, WLAN (2.4-2.5GHz, 3.6-3.7GHzand 4.915- 5.825GHz GHz), Bluetooth (2.4 GHz), and WiMAX (2.500-2.696 GHz, 3.4-3.8 GHz and 5.725-5.850 GHz) communication standard/technologies have found largest use local area, indoor – outdoor communication and entertainment system applications. One of the recent trends in this area of technology is to utilize compatible standards on a single chip solutions, while meeting the requirements of each, to provide customers systems with smaller size, lower power consumption and cheaper in cost. In this thesis, RF – Analog, and – Digital Integrated Circuit design methodologies and techniques are applied to realize a multiband / standart (WLAN and WiMAX) operation capable Voltage- Controlled-Oscillator (VCO) and Frequency Synthesizer. Two of the major building blocks of wireless communication systems are designed using 0.35 μm, AMS-Bipolar (HBT)-CMOS process technology. A new inductor switching concept is implemented for providing the multiband operation capability. Performance parameters such as operating frequencies, phase noise, power consumption, and tuning range are modeled and simulated using analytical approaches, ADS® and Cadence® design and simulation environments. Measurement and/or Figure-of-Merit (FOM) values of our circuits have revealed results that are comparable with already published data, using the similar technology, in the literature, indicating the strength of the design methodologies implemented in this study

A Fully Integrated Multi-Band Multi-Output Synthesizer with Wide-Locking-Range 1/3 Injection Locked Divider Utilizing Self-Injection Technique for Multi-Band Microwave Systems

This dissertation reports the development of a new multi-band multi-output synthesizer, 1/2 dual-injection locked divider, 1/3 injection-locked divider with phase-tuning, and 1/3 injection-locked divider with self-injection using 0.18-micrometer CMOS technology. The synthesizer is used for a multi-band multi-polarization radar system operating in the K- and Ka-band. The synthesizer is a fully integrated concurrent tri-band, tri-output phase-locked loop (PLL) with divide-by-3 injection locked frequency divider (ILFD). A new locking mechanism for the ILFD based on the gain control of the feedback amplifier is utilized to enable tunable and enhanced locking range which facilitates the attainment of stable locking states. The PLL has three concurrent multiband outputs: 3.47-4.313 GHz, 6.94-8.626 GHz and 19.44-21.42-GHz. High second-order harmonic suppression of 62.2 dBc is achieved without using a filter through optimization of the balance between the differential outputs. The proposed technique enables the use of an integer-N architecture for multi-band and microwave systems, while maintaining the benefit of the integer-N architecture; an optimal performance in area and power consumption. The 1/2 dual-ILFD with wide locking range and low-power consumption is analyzed and designed together with a divide-by-2 current mode logic (CML) divider. The 1/2 dual-ILFD enhances the locking range with low-power consumption through optimized load quality factor (QL) and output current amplitude (iOSC) simultaneously. The 1/2 dual-ILFD achieves a locking range of 692 MHz between 7.512 and 8.204 GHz. The new 1/2 dual-ILFD is especially attractive for microwave phase-locked loops and frequency synthesizers requiring low power and wide locking range. The 3.5-GHz divide-by-3 (1/3) ILFD consists of an internal 10.5-GHz Voltage Controlled Oscillator (VCO) functioning as an injection source, 1/3 ILFD core, and output inverter buffer. A phase tuner implemented on an asymmetric inductor is proposed to increase the locking range. The other divide-by-3 ILFD utilizes self-injection technique. The self-injection technique substantially enhances the locking range and phase noise, and reduces the minimum power of the injection signal needed for the 1/3 ILFD. The locking range is increased by 47.8 % and the phase noise is reduced by 14.77 dBc/Hz at 1-MHz offset

캘리브레이션이 필요없는 위상고정 루프의 설계

학위논문 (박사)-- 서울대학교 대학원 : 전기·컴퓨터공학부, 2017. 2. 김재하.A PVT-insensitive-bandwidth PLL and a chirp frequency synthesizer PLL are proposed using a constant-relative-gain digitally-controlled oscillator (DCO), a constant-gain time-to-digital converter (TDC), and a simple digital loop filter (DLF) without an explicit calibration or additional circuit components. A digital LC-PLL that realizes a PVT-insensitive loop bandwidth (BW) by using the constant-relative-gain LC-DCO and constant-gain TDC is proposed. In other words, based on ratiometric circuit designs, the LC-DCO can make a fixed percent change to its frequency for a unit change in its digital input and the TDC can maintain a fixed range and resolution measured in reference unit intervals (UIs) across PVT variations. With such LC-DCO and TDC, the proposed PLL can realize a bandwidth which is a constant fraction of the reference frequency even with a simple proportional-integral digital loop filter without any explicit calibration loops. The prototype digital LC-PLL fabricated in a 28-nm CMOS demonstrates a frequency range of 8.38~9.34 GHz and 652-fs,rms integrated jitter from 10-kHz to 1-GHz at 8.84-GHz while dissipating 15.2-mW and occupying 0.24-mm^2. Also, the PLL across three different die samples and supply voltage ranging from 1.0 to 1.2V demonstrates a nearly constant BW at 822-kHz with the variation of ±4.25-% only. A chirp frequency synthesizer PLL (FS-PLL) that is capable of precise triangular frequency modulation using type-III digital LC-PLL architecture for X-band FMCW imaging radar is proposed. By employing a phase-modulating two-point modulation (TPM), constant-gain TDC, and a simple second-order DLF with polarity-alternating frequency ramp estimator, the PLL achieves a gain self-tracking TPM realizing a frequency chirp with fast chirp slope (=chirp BW/chirp period) without increasing frequency errors around the turn-around points, degrading the effective resolution achievable. A prototype chirp FS-PLL fabricated in a 65nm CMOS demonstrates that the PLL can generate a precise triangular chirp profile centered at 8.9-GHz with 940-MHz bandwidth and 28.8-us period with only 1.9-MHz,rms frequency error including the turn-around points and 14.8-mW power dissipation. The achieved 32.63-MHz/us chirp slope is higher than that of FMCW FS-PLLs previously reported by 2.6x.CHAPTER 1 INTRODUCTION 1 1.1 MOTIVATION 1 1.2 THESIS ORGANIZATION 5 CHAPTER 2 CONVENTIONAL PHASE-LOCKED LOOP 7 2.1 CHARGE-PUMP PLL 7 2.1.1 OPERATING PRINCIPLE 7 2.1.2 LOOP DYNAMICS 9 2.2 DIGITAL PLL 10 2.2.1 OPERATING PRINCIPLE 11 2.2.2 LOOP DYNAMICS 12 CHAPTER 3 VARIATIONS ON PHASE-LOCKED LOOP 14 3.1 OSCILLATOR GAIN VARIATION 14 3.1.1 RING VOLTAGE-CONTROLLED OSCILLATOR 15 3.1.2 LC VOLTAGE-CONTROLLED OSCILLATOR 17 3.1.3 LC DIGITALLY-CONTROLLED OSCILLATOR 19 3.2 PHASE DETECTOR GAIN VARIATION 20 3.2.1 LINEAR PHASE DETECTOR 20 3.2.2 LINEAR TIME-TO-DIGITAL CONVERTER 21 CHAPTER 4 PROPOSED DCO AND TDC FOR CALIBRATION-FREE PLL 23 4.1 DIGTALLY-CONTROLLED OSCILLATOR (DCO) 25 4.1.1 OVERVIEW 24 4.1.2 CONSTANT-RELATIVE-GAIN DCO 26 4.2 TIME-TO-DIGITAL CONVERTER (TDC) 28 4.2.1 OVERVIEW 28 4.2.2 CONSTANT-GAIN TDC 30 CHAPTER 5 PVT-INSENSITIVE-BANDWIDTH PLL 35 5.1 OVERVIEW 36 5.2 PRIOR WORKS 37 5.3 PROPOSED PVT-INSENSITIVE-BANDWIDTH PLL 39 5.4 CIRCUIT IMPLEMENTATION 41 5.4.1 CAPACITOR-TUNED LC-DCO 41 5.4.2 TRANSFORMER-TUNED LC-DCO 45 5.4.3 OVERSAMPLING-BASED CONSTANT-GAIN TDC 49 5.4.4 PHASE DIGITAL-TO-ANALOG CONVERTER 52 5.4.5 DIGITAL LOOP FILTER 54 5.4.6 FREQUENCY DIVIDER 55 5.4.7 BANG-BANG PHASE-FREQUENCY DETECTOR 56 5.5 CELL-BASED DESIGN FLOW 57 5.6 MEASUREMENT RESULTS 58 CHAPTER 6 CHIRP FREQUENCY SYNTHESIZER PLL 66 6.1 OVERVIEW 67 6.2 PRIOR WORKS 71 6.3 PROPOSED CHIRP FREQUENCY SYNTHESIZER PLL 75 6.4 CIRCUIT IMPLEMENTATION 83 6.4.1 SECOND-ORDER DIGITAL LOOP FILTER 83 6.4.2 PHASE MODULATOR 84 6.4.3 CONSTANT-GAIN TDC 85 6.4.4 VRACTOR-BASED LC-DCO 87 6.4.5 OVERALL CLOCK CHAIN 90 6.5 MEASUREMENT RESULTS 91 6.6 SIGNAL-TO-NOISE RATIO OF RADAR 98 CHAPTER 7 CONCLUSION 100 BIBLIOGRAPHY 102 초록 109Docto

Digital enhancement techniques for fractional-N frequency synthesizers

Meeting the demand for unprecedented connectivity in the era of internet-of-things (IoT) requires extremely energy efficient operation of IoT nodes to extend battery life. Managing the data traffic generated by trillions of such nodes also puts severe energy constraints on the data centers. Clock generators that are essential elements in these systems consume significant power and therefore must be optimized for low power and high performance. The focus of this thesis is on improving the energy efficiency of frequency synthesizers and clocking modules by exploring design techniques at both the architectural and circuit levels. In the first part of this work, a digital fractional-N phase locked loop (FNPLL) that employs a high resolution time-to-digital converter (TDC) and a truly ΔΣ fractional divider to achieve low in-band noise with a wide bandwidth is presented. The fractional divider employs a digital-to-time converter (DTC) to cancel out ΔΣ quantization noise in time domain, thus alleviating TDC dynamic range requirements. The proposed digital architecture adopts a narrow range low-power time-amplifier based TDC (TA-TDC) to achieve sub 1ps resolution. Fabricated in 65nm CMOS process, the prototype PLL achieves better than -106dBc/Hz in-band noise and 3MHz PLL bandwidth at 4.5GHz output frequency using 50MHz reference. The PLL achieves excellent jitter performance of 490fsrms, while consumes only 3.7mW. This translates to the best reported jitter-power figure-of-merit (FoM) of -240.5dB among previously reported FNPLLs. Phase noise performance of ring oscillator based digital FNPLLs is severely compromised by conflicting bandwidth requirements to simultaneously suppress oscillator phase and quantization noise introduced by the TDC, ΔΣ fractional divider, and digital-to-analog converter (DAC). As a consequence, their FoM that quantifies the power-jitter tradeoff is at least 25dB worse than their LC-oscillator based FNPLL counterparts. In the second part of this thesis, we seek to close this performance gap by extending PLL bandwidth using quantization noise cancellation techniques and by employing a dual-path digital loop filter to suppress the detrimental impact of DAC quantization noise. A prototype was implemented in a 65nm CMOS process operating over a wide frequency range of 2.0GHz-5.5GHz using a modified extended range multi-modulus divider with seamless switching. The proposed digital FNPLL achieves 1.9psrms integrated jitter while consuming only 4mW at 5GHz output. The measured in-band phase noise is better than -96 dBc/Hz at 1MHz offset. The proposed FNPLL achieves wide bandwidth up to 6MHz using a 50 MHz reference and its FoM is -228.5dB, which is at about 20dB better than previously reported ring-based digital FNPLLs. In the third part, we propose a new multi-output clock generator architecture using open loop fractional dividers for system-on-chip (SoC) platforms. Modern multi-core processors use per core clocking, where each core runs at its own speed. The core frequency can be changed dynamically to optimize for performance or power dissipation using a dynamic frequency scaling (DFS) technique. Fast frequency switching is highly desirable as long as it does not interrupt code execution; therefore it requires smooth frequency transitions with no undershoots. The second main requirement in processor clocking is the capability of spread spectrum frequency modulation. By spreading the clock energy across a wide bandwidth, the electromagnetic interference (EMI) is dramatically reduced. A conventional PLL clock generation approach suffers from a slow frequency settling and limited spread spectrum modulation capabilities. The proposed open loop fractional divider architecture overcomes the bandwidth limitation in fractional-N PLLs. The fractional divider switches the output frequency instantaneously and provides an excellent spread spectrum performance, where precise and programmable modulation depth and frequency can be applied to satisfy different EMI requirements. The fractional divider has unlimited modulation bandwidth resulting in spread spectrum modulation with no filtering, unlike fractional-N PLL; consequently it achieves higher EMI reduction. A prototype fractional divider was implemented in a 65nm CMOS process, where the measured peak-to-peak jitter is less than 27ps over a wide frequency range from 20MHz to 1GHz. The total power consumption is about 3.2mW for 1GHz output frequency. The all-digital implementation of the divider occupies the smallest area of 0.017mm2 compared to state-of-the-art designs. As the data rate of serial links goes higher, the jitter requirements of the clock generator become more stringent. Improving the jitter performance of conventional PLLs to less than (200fsrms) always comes with a large power penalty (tens of mWs). This is due to the PLL coupled noise bandwidth trade-off, which imposes stringent noise requirements on the oscillator and/or loop components. Alternatively, an injection-locked clock multiplier (ILCM) provides many advantages in terms of phase noise, power, and area compared to classical PLLs, but they suffer from a narrow lock-in range and a high sensitivity to PVT variations especially at a large multiplication factor (N). In the fourth part of this thesis, a low-jitter, low-power LC-based ILCM with a digital frequency-tracking loop (FTL) is presented. The proposed FTL relies on a new pulse gating technique to continuously tune the oscillator's free-running frequency. The FTL ensures robust operation across PVT variations and resolves the race condition existing in injection locked PLLs by decoupling frequency tuning from the injection path. As a result, the phase locking condition is only determined by the injection path. This work also introduces an accurate theoretical large-signal analysis for phase domain response (PDR) of injection locked oscillators (ILOs). The proposed PDR analysis captures the asymmetric nature of ILO's lock-in range, and the impact of frequency error on injection strength and phase noise performance. The proposed architecture and analysis are demonstrated by a prototype fabricated in 65 nm CMOS process with active area of 0.25mm2. The prototype ILCM multiplies the reference frequency by 64 to generate an output clock in the range of 6.75GHz-8.25GHz. A superior jitter performance of 190fsrms is achieved, while consuming only 2.25mW power. This translates to a best FoM of -251dB. Unlike conventional PLLs, ILCMs have been fundamentally limited to only integer-N operation and cannot synthesize fractional-N frequencies. In the last part of this thesis, we extend the merits of ILCMs to fractional-N and overcome this fundamental limitation. We employ DTC-based QNC techniques in order to align injected pulses to the oscillator's zero crossings, which enables it to pull the oscillator toward phase lock, thus realizing a fractional-N ILCM. Fabricated in 65nm CMOS process, a prototype 20-bit fractional-N ILCM with an output range of 6.75GHz-8.25GHz consumes only 3.25mW. It achieves excellent jitter performance of 110fsrms and 175fsrms in integer- and fractional-N modes respectively, which translates to the best-reported FoM in both integer- (-255dB) and fractional-N (-252dB) modes. The proposed fractional-N ILCM also features the first-reported rapid on/off capability, where the transient absolute jitter performance at wake-up is bounded below 4ps after less than 4ns. This demonstrates almost instantaneous phase settling. This unique capability enables tremendous energy saving by turning on the clock multiplier only when needed. This energy proportional operation leverages idle times to save power at the system-level of wireline and wireless transceivers

Synthétiseur de fréquences RF destiné aux dispositifs médicaux implantables

RÉSUMÉ Les microsystèmes biomédicaux implantables présentent un énorme potentiel pour la recherche médicale. Les dispositifs médicaux intelligents implantables, qui combinent des capteurs et/ou des actuateurs avec des circuits intégrés, ouvrent la voie à des applications fascinantes. Aujourd’hui, la possibilité d’utiliser la technologie CMOS pour intégrer des circuits RF, numériques, et même certains types de capteurs sur une même puce, suscite un vif intérêt dans un domaine nouveau : celui des réseaux de capteurs implantables, ou BSN (Body-Sensor Networks) et leurs applications en recherche biomédicale. L’implantation dans le corps de tels réseaux de capteurs sans-fils permettrait de surveiller, détecter ou même combattre différentes maladies, et ce de manière in situ. Avec des dimensions minimales inférieures à 100 nm, la technologie CMOS représente un choix viable pour l’implémentation des blocs de bases des circuits intégrés radio-fréquences (Radio- Frequency Integrated Circuits - RFIC) à faible consommation de puissance. Toutefois, la réduction de la tension d’alimentation permise dans les procédés CMOS nanométriques, l’impédance de sortie limitée des transistors disponibles, ainsi que les variations de procédés ont pour conséquence que plusieurs architectures de circuits analogiques n’offrent plus les performances requises ou ne sont tout simplement plus applicables. Des méthodes de conception innovatrices doivent être utilisées et des compromis judicieux doivent être faits afin de maintenir les performances requises. Dans un système de communication sans-fil, l’oscillateur local (Local Oscillator - LO) est l’un des modules les plus importants puisqu’il sert à générer la porteuse du lien RF qui sera par la suite modulée pour transmettre les données. Dans un contexte où la consommation de puissance doit être strictement minimisée, la génération d’une fréquence porteuse RF stable dans un procédé CMOS nanométrique présente des défis énormes. Dans cette optique, cette thèse se concentre sur la conception, l’analyse, ainsi que sur l’implémentation de circuits analogiques et RF à basse tension faisant partie d’un synthétiseur de fréquences à consommation ultra faible utilisant un procédé CMOS nanométrique. Tout d’abord, une nouvelle architecture de miroir de courant présentant une impédance de sortie très élevée destiné aux applications à faible tension d’alimentation est présentée. Ce miroir de courant de faible complexité présente une résistance de sortie très élevée et ce pour des tensions de sortie s’approchant des alimentations. Ensuite, une nouvelle architecture de pompe de charges CMOS destinée aux boucles à verrouillage de phase à faible tension et faible puissance est proposée afin de contourner les difficultés causées par la basse tension d’alimentation et la faible impédance de sortie des transistors nanométriques.----------ABSTRACT Implantable biomedical microsystems present a huge potential for medical research. The recent possibility to use CMOS technology to integrate radio-frequency (RF) circuits, baseband signal processing, and even sensors on a same chip has led to a tremendous growth of interest in wireless sensors and their applications. Such microsystems typically include a microprocessor and memory, an energy source, one or more sensors, an analog-to-digital converter (ADC), and a RF transceiver to communicate with a remote base-station or processing unit. In the biomedical field, it is expected that implanting such wireless sensing microsystems could greatly help the medical research community in learning about the progression of some diseases and assess degree of response to treatment. With a minimum feature size that has reduced under 100 nm, CMOS technology has become a viable choice for the implementation of low-power radio-frequency integrated circuits (RFIC) building blocks. However, the reduction of the supply voltage combined with the low output impedance of nanometer transistors have caused many analog and RF circuit solutions to be unsuitable, or even unusable due to voltage headroom constraints. Therefore, new circuit techniques and innovative design approaches are needed in order to meet the required performance level while maintaining low power consumption. In a wireless communications system, the local oscillator (LO) is one of the most important building blocks since it generates the RF carrier signal upon which data is modulated for transmission. In a context where power consumption must be strictly minimized, the generation of a stable RF carrier using a nanometer CMOS process presents huge challenges. In this regard, this thesis focuses on the design, the analysis and the implementation of low-voltage analog and RF circuits used to build an ultra-low power integer-N frequency synthesizer. First, a new current mirror architecture dedicated to low-voltage, low-power applications is presented. The proposed current mirror offers a very high output resistance and an enhanced output voltage range in comparison with other current mirrors similar in architecture. Then, a novel charge pump dedicated to low-power low-voltage PLLs is proposed. The design of this circuit was motivated by the need of a nano-CMOS charge pump that would offer constant current magnitude and minimum current mismatch over a wide range of output voltage, while maintaining power consumption and complexity level as low as possible. A LC resonator-based voltage-controlled oscillator (LC-VCO) that implements a new technique to reduce the impact of process variation on phase noise and power consumption is presented