Integrated Circuits for Programming Flash Memories in Portable Applications

Smart devices such as smart grids, smart home devices, etc. are infrastructure systems that connect the world around us more than before. These devices can communicate with each other and help us manage our environment. This concept is called the Internet of Things (IoT). Not many smart nodes exist that are both low-power and programmable. Floating-gate (FG) transistors could be used to create adaptive sensor nodes by providing programmable bias currents. FG transistors are mostly used in digital applications like Flash memories. However, FG transistors can be used in analog applications, too. Unfortunately, due to the expensive infrastructure required for programming these transistors, they have not been economical to be used in portable applications. In this work, we present low-power approaches to programming FG transistors which make them a good candidate to be employed in future wireless sensor nodes and portable systems. First, we focus on the design of low-power circuits which can be used in programming the FG transistors such as high-voltage charge pumps, low-drop-out regulators, and voltage reference cells. Then, to achieve the goal of reducing the power consumption in programmable sensor nodes and reducing the programming infrastructure, we present a method to program FG transistors using negative voltages. We also present charge-pump structures to generate the necessary negative voltages for programming in this new configuration

Digital Controlled Multi-phase Buck Converter with Accurate Voltage and Current Control

abstract: A 4-phase, quasi-current-mode hysteretic buck converter with digital frequency synchronization, online comparator offset-calibration and digital current sharing control is presented. The switching frequency of the hysteretic converter is digitally synchronized to the input clock reference with less than ±1.5% error in the switching frequency range of 3-9.5MHz. The online offset calibration cancels the input-referred offset of the hysteretic comparator and enables ±1.1% voltage regulation accuracy. Maximum current-sharing error of ±3.6% is achieved by a duty-cycle-calibrated delay line based PWM generator, without affecting the phase synchronization timing sequence. In light load conditions, individual converter phases can be disabled, and the final stage power converter output stage is segmented for high efficiency. The DC-DC converter achieves 93% peak efficiency for Vi = 2V and Vo = 1.6V.Dissertation/ThesisDoctoral Dissertation Electrical Engineering 201

2.45ghz Rf-front End for a Micro Neural Interface System

Active implants inside the human body must be capable of performing their intended function for decades without replacement with minimal tissue heating. It is therefore necessary for them to efficiently operate reliably in a battery free environment at very low power levels. Traditionally inductive coupling has been the preferred choice of power transfer to the active implants. Inductive coupling suffers from bandwidth and alignment issues that limit their usefulness for distributed sensor systems. The ability to use both near-field and far-field RF to power and communicate with sensors distributed in the body would provide a major advance in implantable device technology. Recent advances in wafer packaging technologies and advanced VLSI processes offer the possibility of highly reliable system on chip (SOC) solutions using RF energy as a source to power the active implants. In this paper we present a CMOS VLSI implementation of a front end system for a RFID Sensor (RFIDS) capable of harvesting up to 42�W at -3dBm power levels and providing 700mV and 400mV regulated DC voltages under 50 �A and 4�A continuous load currents respectively. In addition the RFIDS contains both an AM demodulator and a 400mV voltage reference. The RF front end chip occupies an area of 2.32 mm2 and has been fabricated in 180nm IBM CMRF7SF processSchool of Electrical & Computer Engineerin

Front-end receiver for miniaturised ultrasound imaging

Point of care ultrasonography has been the focus of extensive research over the past few decades. Miniaturised, wireless systems have been envisaged for new application areas, such as capsule endoscopy, implantable ultrasound and wearable ultrasound. The hardware constraints of such small-scale systems are severe, and tradeoffs between power consumption, size, data bandwidth and cost must be carefully balanced. To address these challenges, two synthetic aperture receiver architectures are proposed and compared. The architectures target highly miniaturised, low cost, B-mode ultrasound imaging systems. The first architecture utilises quadrature (I/Q) sampling to minimise the signal bandwidth and computational load. Synthetic aperture beamforming is carried out using a single-channel, pipelined protocol in order to minimise system complexity and power consumption. A digital beamformer dynamically apodises and focuses the data by interpolating and applying complex phase rotations to the I/Q samples. The beamformer is implemented on a Spartan-6 FPGA and consumes 296mW for a frame rate of 7Hz. The second architecture employs compressive sensing within the finite rate of innovation (FRI) framework to further reduce the data bandwidth. Signals are sampled below the Nyquist frequency, and then transmitted to a digital back-end processor, which reconstructs I/Q components non-linearly, and then carries out synthetic aperture beamforming. Both architectures were tested in hardware using a single-channel analogue front-end (AFE) that was designed and fabricated in AMS 0.35μm CMOS. The AFE demodulates RF ultrasound signals sequentially into I/Q components, and comprises a low-noise preamplifier, mixer, programmable gain amplifier (PGA) and lowpass filter. A variable gain low noise preamplifier topology is used to enable quasi-exponential time-gain control (TGC). The PGA enables digital selection of three gain values (15dB, 22dB and 25.5dB). The bandwidth of the lowpass filter is also selectable between 1.85MHz, 510kHz and 195kHz to allow for testing of both architectural frameworks. The entire AFE consumes 7.8 mW and occupies an area of 1.5×1.5 mm. In addition to the AFE, this thesis also presents the design of a pseudodifferential, log-domain multiplier-filter or “multer” which demodulates low-RF signals in the current-domain. This circuit targets high impedance transducers such as capacitive micromachined ultrasound transducers (CMUTs) and offers a 20dB improvement in dynamic range over the voltage-mode AFE. The bandwidth is also electronically tunable. The circuit was implemented in 0.35μm BiCMOS and was simulated in Cadence; however, no fabrication results were obtained for this circuit. B-mode images were obtained for both architectures. The quadrature SAB method yields a higher image SNR and 9% lower root mean squared error with respect to the RF-beamformed reference image than the compressive SAB method. Thus, while both architectures achieve a significant reduction in sampling rate, system complexity and area, the quadrature SAB method achieves better image quality. Future work may involve the addition of multiple receiver channels and the development of an integrated system-on-chip.Open Acces

Diseño de circuitos electrónicos de ultra-bajo consumo en tecnologías nanométricas

El escalado de los procesos de fabricación de semiconductores, predicho por el Dr. Moore en los años sesenta, ha tenido un gran impacto en el desarrollo de la electrónica integrada actual. Por una parte, la reducción del tamaño de los transistores ha permitido incrementar la densidad de integración, dando la posibilidad a los diseñadores de introducir un mayor número de funcionalidades dentro de una misma área. Por otro lado, este fenómeno ha llevado consigo una reducción de los costes asociados a la fabricación, logrando abaratar el producto final. Esta continua evolución e incremento de la funcionalidad dentro de un mismo circuito integrado, implica, a su vez, un aumento de la complejidad a la hora de planificar la generación y distribución de las distintas tensiones de alimentación, necesarias para cada uno de los bloques incluidos en el chip. Esto provoca que las especificaciones de ruido, regulación y/o estabilidad asociadas a cada dominio de alimentación varíen según la naturaleza del sistema al que se pretende alimentar. Por esta razón, los circuitos destinados a la gestión de la potencia han tomado una mayor relevancia en los últimos años, puesto que las restricciones impuestas por los sistemas integrados son cada vez mayores. Dentro de los circuitos destinados a la gestión de potencia, los reguladores lineales y, en concreto, los de bajo dropout se corresponden con un bloque básico, ya que permiten la generación de tensiones de alimentación muy estables, precisas y de bajo ruido. Estas características los convierten en el circuito ideal para alimentar a sistemas analógicos o de radio-frecuencia, muy sensibles a variaciones de la alimentación. Otra característica de estos bloques, que ha provocado el creciente interés de la comunidad científica en ellos, es la posibilidad de poder integrarlos sin necesidad de incluir ningún dispositivo externo, con el consecuente ahorro económico y de área en la tarjeta impresa. Sin embargo, dentro de los inconvenientes cabe destacar dos. Por una parte, la eficiencia máxima teórica que pueden lograr es baja frente a soluciones basadas en capacidades conmutadas o inductores. Por otro lado, al buscarse un esquema de compensación interna, el polo dominante del sistema viene fijado por un nodo interno del circuito, provocando que el polo no-dominante esté dominado por la carga. Esto se traduce en un gran problema de estabilidad, debido a que las variaciones que sufre la carga se traducen en un desplazamiento en frecuencia del polo no dominante, degradando el margen de fase de todo el sistema. Según lo descrito anteriormente, esta investigación se ha centrado en el estudio de reguladores lineales de tipo Low-DropOut o LDO compensados internamente y sus propiedades, dada la problemática de este tipo de celdas cuando se busca minimizar su consumo quiescente. Para ello, uno de los objetivos marcados versa sobre la búsqueda de topologías alternativas que permitan el diseño de LDOs de altas prestaciones, sin suponer un incremento del consumo quiescente y que sean válidos para entornos de baja tensión de alimentación. En este sentido, se ha apostado por el uso de la celda Flipped Voltage Follower como regulador debido a su baja impendancia de salida, gran estabilidad y sencillez. Una segunda línea, se ha centrado en la búsqueda de esquemas de compensación simples que permitan extender la estabilidad de este tipo de regulador en todo el rango de funcionamiento. Para ello, se ha explorado un esquema basado en la compensación clásica de Miller donde se ha utilizado un esquema de replica para ajustar de forma dinámica el valor de la resistencia según la carga del sistema. Por último, con el objetivo de minimizar lo máximo posible el consumo quiescente de los reguladores LDOs sin degradar las prestaciones de la respuesta transitoria, se ha explorado el uso de buffers clase AB para gestionar la puerta del transistor de paso. Esta técnica permite mejorar la respuesta transitoria, al ser capaz de crear corrientes elevadas durante las transiciones sin necesidad de penalizar la eficiencia del regulador.The continuous downscaling of semiconductor fabrication processes, which was predicted by PhD. Moore in 1965, have had a great impact in the development of nowadays integrated electronics. The reduction of transistor size has allowed, on one hand, the integration of more devices in the same área, increasing the integration density, while, on the other hand, has led to the reduction of fabrication costs, making the final product cheaper and accessible. However, this increase in the functionality of a single integrated circuit entails greater complexity in the generation and distribution of the different biasing voltages needed throughout one chip. Thus, as more different systems are integrated in the same chip, more different biasing domains coexists in it, leading several different requirements of noise, regulation and/or stability that need to be satisfied simultaneously. Therefore, power management circuits have been acquiring greater significance as technology downscales, reaching its maximum nowadays, when the nanoscale had taken those issues to its culmen. Linear regulators, and more concretely, low-dropout linear regulators, are an essential block in any power management system, able to generate precise and extremely-stable low-noise biasing voltages what make them the ideal choice for extremely biasing-sensitive circuits such as analog or radio-frequency systems. In addition to this, low-dropout linear regulators can be completely integrated without needing any external device, what translates to expenses and area savings. For all these reasons, low-dropout linear regulators have been lately acquiring extensive attention from the scientific community. However, those circuits also have some disadvantages, indeed, the maximum theoretical efficiency that can be achieved though low-dropout linear regulators is lower than switched capacitor or inductor-based solutions efficiency. In addition to this, as internal compensation is required, the system’s dominant pole is given by an internal node, making the non-dominant pole to be fixed by the charge. This leads to a great stability concern as charge variations translate to a frequency displacement of the non-dominant pole that degrades the whole system phase margin. In accordance with previously described issues, this research has been focused on the study of minimum-quiescent consumption internally compensated low-dropout linear regulators (LDO). The first objective of this research is the proposal of low-voltage high-performance LDO structures that do not increase quiescent consumption. Thus, the Flipped Voltage Follower cell has been proposed as regulator due to its inherent low output impedance, great stability and simplicity. The second aim of this research has been the proposal of simple compensation schemes that allow full-operation range stability. So that, a classical Miller compensation based scheme where a replica circuit dynamically adjust the charge resistance has been proposed. Finally, in order to minimize quiescent consumption of LDOs regulators without degrading transient response performance, class-AB buffers have been proposed to drive the pass transistor gate. This technique enhances the transient response as it generates high currents during transitions without compromising efficiency.Premio Extraordinario de Doctorado U

Wide Bandwidth - High Accuracy Control Loops in the presence of Slow Varying Signals and Applications in Active Matrix Organic Light Emitting Displays and Sensor Arrays

This dissertation deals with the problems of modern active matrix organic light-emitting diode AMOLED display back-plane drivers and sensor arrays. The research described here, aims to classify recently utilized compensation techniques into distinct groups and further pinpoint their advantages and shortcomings. Additionally, a way of describing the loops as mathematical constructs is utilized to derive new circuits from the analog design perspective. A novel principle on display driving is derived by observing those mathematical control loop models and it is analyzed and evaluated as a novel way of pixel driving. Specifically, a new feedback current programming architecture and method is described and validated through experiments, which is compatible with AMOLED displays having the two transistor one capacitor (2T1C) pixel structure. The new pixel programming approach is compatible with all TFT technologies and can compensate for non-uniformities in both threshold voltage and carrier mobility of the pixel OLED drive TFT. Data gathered show that a pixel drive current of 20 nA can be programmed in less than 10usec. This new approach can be implemented within an AMOLED external or integrated display data driver. The method to achieve robustness in the operation of the loop is also presented here, observed through a series of measurements. All the peripheral blocks implementing the design are presented and analyzed through simulations and verified experimentally. Sources of noise are identified and eliminated, while new techniques for better isolation from digital noise are described and tested on a newly fabricated driver. Multiple versions of the new proposed circuit are outlined, simulated, fabricated and measured to evaluate their performance.A novel active matrix array approach suitable for a compact multi-channel gas sensor platform is also described. The proposed active matrix sensor array utilizes an array of P-i-N diodes each connected in series with an Inter-Digitated Electrode (IDE). The functionality of 8x8 and 16x16 sensor arrays measured through external current feedback loops is also presented for the 8x8 arrays and the detection of ammonia (NH3) and chlorine (Cl2) vapor sources is demonstrated