無線センサネットワークのための超低消費電力と高感度CMOS RF受信機に関する研究

Wireless sensor networks (WSN) have been applied in wide range of applications and proved the more and more important contribution in the modern life. In order to evaluate a WSN, many metrics are considered such as cost, latency, power or quality of service. However, since the sensor nodes are usually deployed in large physical areas and inaccessible locations, the battery change becomes impossible. In this scenario, the power consumption is the most important metric. In a sensor node, the RF receiver is one of the communication devices, which consume a vast majority of power. Therefore, this thesis studies ultra low power RF receivers for the long lifetime of the sensor nodes. Currently, the WSNs use various frequency bands. However, for low power target, the sub-GHz frequency bands are preferred. In this study, ultra-low power 315 MHz and 920 MHz receivers will be proposed for short-range applications and long-range applications of the WSNs respectively. To achieve ultra-low power target, the thesis considers some issues in architecture, circuit design and fabrication technology for suitable choices. After considering different receiver architectures, the RF detection receiver with the On-Off-Keying (OOK) modulation is chosen. Then the thesis proposes solutions to reduce power consumption and concurrently guarantee high sensitivity for the receivers so that they can communicate at adequate distances for both short and long-range applications. First, a 920 MHz OOK receiver is designed for the long-range WSN applications. Typically, the RF amplifiers and local oscillators consume the most of power of RF receivers. In the RF detection receivers, the local oscillators are eliminated, however, the power consumption of the RF amplifiers is still dominant. By reducing the RF gain or removing the RF amplifier, the power consumption of the receivers can be reduced drastically. However, in this case the sensitivity is very limited. In order to overcome the trade-off between power consumption and sensitivity, the switched bias is applied to the RF amplifiers to reduce their power consumption substantially while guaranteeing high RF gain before RF detection. As a result, the receiver consumes only 53 W at 0.6 V supply with -82 dBm sensitivity at 10 kbps data rate. Next, an OOK receiver operating at 315 MHz for the short-range WSN applications with low complexity is proposed. In this receiver, the RF amplifier is controlled to operate intermittently for power reduction. Furthermore, taking advantage of the low carrier frequency, a comparator is used to convert the RF signal to a rail-to-rail stream and then data is demodulated in the digital domain. Therefore, no envelope detector or baseband amplifiers is required. The architecture of the receiver is verified by using discrete RF modules and FPGAs before it is designed on CMOS technology. By simulation with the physical layout, the 315 MHz OOK receiver consumes 27.6 W at 200 kbps and achieves -76.4 dBm sensitivity. Finally, the Synchronized-OOK (S-OOK) modulation scheme is proposed and then an S-OOK receiver operating in the 315 MHz frequency is developed to reduce power consumption more deeply. The S-OOK signal contains not only data but also clock information. By generating a narrow window, the RF front-end is enabled to receive signal only in a short period, therefore, power consumption of the receiver is reduced further. In addition, thank to the clock information contained in the input signal, the data and corresponding clock are demodulated simultaneously without a clock and data recovery circuit. The architecture of the S-OOK receiver is also verified by using discrete RF modules and FPGAs, then VLSI design is carried out. Physical layout simulation shows that the receiver can achieve -76.4 dBm sensitivity, consumes 8.39 W, 4.49 W, 1.36 W at 100 kbps, 50 kbps and 10 kbps respectively. In conclusion, with the objective is to look for solutions to minimize power consumption of receivers for extending the lifetime of sensor nodes while guaranteeing high sensitivity, this study proposed novel receiver architectures, which help reduce power consumption significantly. If using the coin battery CR2032 for power supply, the 920 MHz OOK receiver can work continuously in 1.45 years with communication distance of 259 meters; the 315 MHz OOK receivers can work continuously in 2.8 years with approximately 19 meters communication distance in free space. Whereas, the 315 MHz S-OOK receiver with the minimum power consumption of 1.36 W is suitable for batteryless sensor nodes.電気通信大学201

Development of an Encrypted Wireless System for Body Sensor Network Applications

Wireless body area networks (WBAN), also called wireless body sensor networks (WBSN), consist of a collection of wireless sensor nodes used to monitor and assess various human physiological conditions, which can then be used by healthcare professionals to help them make important healthcare decisions. They can be used to prevent disease, help diagnosis a disease, or manage the symptoms of a disease. An extremely important aspect of WBAN is security to protect a patient\u27s healthcare information, as a hacker could potentially cause fatal harm. Current security measures are implemented in software at the MAC layer and higher, not in the physical layer. Previous research demonstrated a chaotic encryption cipher to add a layer of security in the physical layer. This cipher exploits different properties of the Lorenz chaotic system to encrypt and decrypt digital data. Decryption involved synchronizing two chaotic signals to recover original data by sharing a state between the transmitter and receiver. In this thesis, we further develop the encryption system by implementing wireless capabilities. We use two approaches: the first by using commercially available wireless microcontrollers that communicate using Bluetooth Low Energy, and the second by the design and fabrication of a dual-band low noise amplifier (LNA) that can be used in a receiver for WBANs collecting data from implantable and on-the-body sensors. For the first approach, a custom Bluetooth Low Energy profile was created for streaming the analog encrypted signal, and signal processing was done at the receiver side. For the second approach, the LNA operates at the Medical Implant Communication System (MICS) band and the 915 MHz Industrial, Scientific, and Medical (ISM) band simultaneously through dual-band input and output matching networks

Low-power CMOS front-ends for wireless personal area networks

The potential of implementing subthreshold radio frequency circuits in deep sub-micron CMOS technology was investigated for developing low-power front-ends for wireless personal area network (WPAN) applications. It was found that the higher transconductance to bias current ratio in weak inversion could be exploited in developing low-power wireless front-ends, if circuit techniques are employed to mitigate the higher device noise in subthreshold region. The first fully integrated subthreshold low noise amplifier was demonstrated in the GHz frequency range requiring only 260 μW of power consumption. Novel subthreshold variable gain stages and down-conversion mixers were developed. A 2.4 GHz receiver, consuming 540 μW of power, was implemented using a new subthreshold mixer by replacing the conventional active low noise amplifier by a series-resonant passive network that provides both input matching and voltage amplification. The first fully monolithic subthreshold CMOS receiver was also implemented with integrated subthreshold quadrature LO (Local Oscillator) chain for 2.4 GHz WPAN applications. Subthreshold operation, passive voltage amplification, and various low-power circuit techniques such as current reuse, stacking, and differential cross coupling were combined to lower the total power consumption to 2.6 mW. Extremely compact resistive feedback CMOS low noise amplifiers were presented as a cost-effective alternative to narrow band LNAs using high-Q inductors. Techniques to improve linearity and reduce power consumption were presented. The combination of high linearity, low noise figure, high broadband gain, extremely small die area and low power consumption made the proposed LNA architecture a compelling choice for many wireless applications.Ph.D.Committee Chair: Laskar, Joy; Committee Member: Chakraborty, Sudipto; Committee Member: Chang, Jae Joon; Committee Member: Divan, Deepakraj; Committee Member: Kornegay, Kevin; Committee Member: Tentzeris, Emmanoui

Wireless Transceivers for Implantable Microsystems.

In this thesis, we present the first-ever fully integrated mm3 low-power biomedical transceiver with 1 meter of range that is powered by a mm2 thin-film battery. The transceiver is targeted for biomedical implants where size and energy constraints dictated by application make design challenging. Despite all the previous work in RFID tags, form factor of such radios is incompatible with mm3 biomedical implants. The proposed transceiver bridges this gap by providing a compact low-power solution that can run off small thin-film batteries and can be stacked with other system components in a 3D fashion. On the sensor-to-external side, we proposed a novel FSK architecture based on dual-resonator LC oscillators to mitigate unwanted overlap of two FSK tones’ phase noise spectrum. Due to inherent complexity of such systems, fourth order dual-resonator oscillators can exhibit instable operation. We mathematically modeled the instability and derive design conditions for stable oscillations. Through simulation and measurements, validity of derived models was confirmed. Together with other low-power system blocks, the transmitter was successfully implanted in live mouse and in-vivo measurements were performed to confirm successful transmission of vital signals through organic tissue. The integrated transmitter achieved a bit-error-rate of 10-6 at 10cm with 4.7nJ/bit energy consumption. On the external-to-sensor link, we proposed a new protocol to lower receiver peak power, which is highly limited due to small size of mm3 microsystem battery. In the proposed protocol, sending same data multiple times drastically relaxes jitter requirement on the sensor side at the cost of increased power consumption on the external side without increasing peak power radiated by the external unit. The receiver also uses a dual-coil LNA to improve range by 22% with only 11% area overhead. An asynchronous controller manages protocol timing and limits total monitoring current to 43nA. The fabricated receiver consumes 1.6nJ/bit at 40kbps while positioned 1m away from a 2W source.PhDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/102458/1/ghaed_1.pd

Radio-frequency integrated-circuit design for CMOS single-chip UWB systems

Low cost, a high-integrated capability, and low-power consumption are the basic requirements for ultra wide band (UWB) system design in order for the system to be adopted in various commercial electronic devices in the near future. Thus, the highly integrated transceiver is trended to be manufactured by companies using the latest silicon based complimentary metal-oxide-silicon (CMOS) processes. In this dissertation, several new structural designs are proposed, which provide solutions for some crucial RF blocks in CMOS for UWB for commercial applications. In this dissertation, there is a discussion of the development, as well as an illustration, of a fully-integrated ultra-broadband transmit/receive (T/R) switch which uses nMOS transistors with deep n-well in a standard 0.18-μm CMOS process. The new CMOS T/R switch exploits patterned-ground-shield on-chip inductors together with MOSFET’s parasitic capacitances in order to synthesize artificial transmission lines which result in low insertion loss over an extremely wide bandwidth. Within DC-10 GHz, 10-18 GHz, and 18-20 GHz, the developed CMOS T/R switch exhibits insertion loss of less than 0.7, 1.0 and 2.5 dB and isolation between 32-60 dB, 25-32 dB, and 25-27 dB, respectively. The measured 1-dB power compression point and input third-order intercept point reach as high as 26.2 and 41 dBm, respectively. Further, there is a discussion and demonstration of a tunable Carrier-based Time-gated UWB transmitter in this dissertation which uses a broadband multiplier, a novel fully integrated single pole single throw (SPST) switch designed by the CMOS process, where a tunable instantaneous bandwidth from 500 MHz to 4 GHz is exhibited by adjusting the width of the base band impulses in time domain. The SPST switch utilizes the synthetic transmission line concept and multiple reflections technique in order to realize a flat insertion loss less than 1.5 dB from 3.1 GHz to 10.6 GHz and an extremely high isolation of more than 45 dB within this frequency range. A fully integrated complementary LC voltage control oscillator (VCO), designed with a tunable buffer, operates from 4.6 GHz to 5.9 GHz. The measurement results demonstrate that the integrated VCO has a very low phase noise of –117 dBc/ Hz at 1 MHz offset. The fully integrated VCO achieves a very high figure of merit (FOM) of 183.5 using standard CMOS process while consuming 4 mA DC current

Energy autonomous systems : future trends in devices, technology, and systems

The rapid evolution of electronic devices since the beginning of the nanoelectronics era has brought about exceptional computational power in an ever shrinking system footprint. This has enabled among others the wealth of nomadic battery powered wireless systems (smart phones, mp3 players, GPS, …) that society currently enjoys. Emerging integration technologies enabling even smaller volumes and the associated increased functional density may bring about a new revolution in systems targeting wearable healthcare, wellness, lifestyle and industrial monitoring applications

RF techniques for IEEE 802.15.4: circuit design and device modelling

The RF circuitry in the physical layer of any wireless communication node is arguably its most important part. The front-end radio is the hardware that enables communication by transmitting and receiving information. Without a robust and high performance front-end, all other higher layers of signal processing and data handling in a wireless network are irrelevant. This thesis investigates the radio circuitry of wireless-networked nodes, and introduces several proposals for improvement. As an emerging market, analysis starts by examining available and ratified network standards suitable for low power applications. After identifying the IEEE 802.15.4 standard (commercially known as ZigBee) as the one of choice, and analysing several front-end architectures on which its transceiver circuitry can be based, an application, the Tyre Pressure Monitoring System (TPMS) is selected to examine the capabilities of the standard and its most suitable architecture in satisfying the application’s requirements. From this compatibility analysis, the most significant shortcomings are identified as interference and power consumption. The work presented in this thesis focuses on the power consumption issues. A comparison of available high frequency transistor technologies concludes Silicon CMOS to be the most appropriate solution for the implementation of low cost and low power ZigBee transceivers. Since the output power requirement of ZigBee is relatively modest, it is possible to consider the design of a single amplifier block which can act as both a Low Noise Amplifier (LNA) in the receiver chain and a Power Amplifier (PA) on the transmitter side. This work shows that by employing a suitable design methodology, a single dual-function amplifier can be realised which meets the required performance specification. In this way, power consumption and chip area can both be reduced, leading to cost savings so vital to the widespread utilisation of the ZigBee standard. Given the importance of device nonlinearity in such a design, a new transistor model based on independent representation of each of the transistor’s nonlinear elements is developed with the aim of quantifying the individual contribution of each of the transistors nonlinear elements, to the total distortion. The methodology to the design of the dual functionality (LNA/PA) amplifier starts by considering various low noise amplifier architectures and comparing them in terms of the trade-off between noise (required for LNA operation) and linearity (important for PA operation), and then examining the behaviour of the selected architecture (the common-source common-gate cascode) at higher than usual input powers. Due to the need to meet the far apart performance requirements of both the LNA and PA, a unique amplifier design methodology is developed The design methodology is based on simultaneous graphical visualisation of the relationship between all relevant performance parameters and corresponding design parameters. A design example is then presented to demonstrate the effectiveness of the methodology and the quality of trade-offs it allows the designer to make. The simulated performance of the final amplifier satisfies both the requirements of ZigBee’s low noise and power amplification. At 2.4GHz, the amplifier is predicted to have 1.6dB Noise Figure (NF), 6dBm Input-referred 3rd-order Intercept Point (IIP3), and 1dB compression point of -3.5dBm. In low power operation, it is predicted to have 10dB gain, consuming only 8mW. At the higher input power of 0dBm, it is predicted to achieve 24% Power-Added Efficiency (PAE) with 8dB gain and 22mW power consumption. Finally, this thesis presents a set of future research proposals based on problems identified throughout its development

Ultra Wideband

Ultra wideband (UWB) has advanced and merged as a technology, and many more people are aware of the potential for this exciting technology. The current UWB field is changing rapidly with new techniques and ideas where several issues are involved in developing the systems. Among UWB system design, the UWB RF transceiver and UWB antenna are the key components. Recently, a considerable amount of researches has been devoted to the development of the UWB RF transceiver and antenna for its enabling high data transmission rates and low power consumption. Our book attempts to present current and emerging trends in-research and development of UWB systems as well as future expectations