HIGH VOLTAGE RESONANT SELF-TRACKING CURRENT-FED CONVERTER

High voltage power supply design presents unique requirements, combining safety, controllability, high performance, and high efficiencies. A new Resonant Self-Tracking Current-Fed Converter (RST-CFC) is investigated as a proof-of-concept of a high voltage power supply particularly for an X-ray system. These systems require fast voltage rise times and low ripple to yield a clear image. The proposed converter implements high-frequency resonance among discrete components and transformer parasitics to achieve high voltage gain, and the self-tracking nature ensures operation at maximum gain while power switches achieve zero-voltage switching across the full load range. This converter exhibits an inherent indefinite short-circuit capability. Theoretical results were obtained through simulations and verified by experimental results through a complete test configuration. Converter topology viability was confirmed through hardware testing and characterization

A very simple analog control for QSW-ZVS source/sink buck converter with seamless mode transition

A simple, analog, control circuit is proposed for seamless transition between source and sink modes in a Quasi-Square-Wave Zero Voltage Switching (QSW-ZVS) source/sink buck converter. The inductor current is controlled by a variablewidth hysteretic current mode control. The upper and lower bounds of the hysteretic band are clamped to ensure QSW-ZVS operation with a single current command from the control loop and independently from the power flow direction. This enables the control of any PWM converter able to operate in QSW-ZVS with a single control loop. If the proposed circuit is used, using a complex multi-mode or look-up-table based digital control is no longer required, simplifying the implementation and lowering the cost of the converter. A 50 W buck converter is built to demonstrate the proposed control circuit and experimental measurements are shown to verify its correct operation.Este trabajo ha sido financiado por el Gobierno de España a través del proyecto DPI2013-47176-C2-2-R y el Gobierno del Principado de Asturias a través del proyecto SV-PA-17-RIS3-4, la beca “Severo Ochoa” BP14-085 y los fondos FEDER.Nineteenth IEEE Workshop on Control and Modeling for Power Electronics, IEEE COMPEL 201

Efficiency Improvement of LDO Output Based Linear Regulator With Supercapacitor Energy Recovery – A versatile new technique with an example of a 5V to 1.5V version

Supercapacitors are used in various industrial applications and the supercapacitors technology is gradually progressing into a mature state. Common applications of supercapacitors are in electric vehicles, hybrid electric vehicles, uninterruptible power supply (UPS) and in portable devices such as cellular phones and laptops. The capacitance values range from fractional Farads to few thousand Farads and their continuos DC voltage ratings are from 2V to 6V. At University of Waikato, a team works on using supercapacitors for improving the efficiency of linear voltage regulators. In particular, this patented technique aims at combining off the shelfs LDO ICs and a supercapacitor array for improving end to end efficiency of linear regulator. My work is aimed at developing the theoretical background and designing prototype circuitry for a voltage regulator for the case of unregulated input supply is more than 3 times of the minimum input voltage requirement of the LDO which is applicable for a 5V to 1.5V regulator. Experimental results are indicated with future suggestions for improvement

Highly Integrated Dc-dc Converters

A monolithically integrated smart rectifier has been presented first in this work. The smart rectifier, which integrates a power MOSFET, gate driver and control circuitry, operates in a self-synchronized fashion based on its drain-source voltage, and does not need external control input. The analysis, simulation, and design considerations are described in detail. A 5V, 5-µm CMOS process was used to fabricate the prototype. Experimental results show that the proposed rectifier functions as expected in the design. Since no dead-time control needs to be used to switch the sync-FET and ctrl-FET, it is expected that the body diode losses can be reduced substantially, compared to the conventional synchronous rectifier. The proposed self-synchronized rectifier (SSR) can be operated at high frequencies and maintains high efficiency over a wide load range. As an example of the smart rectifier\u27s application in isolated DC-DC converter, a synchronous flyback converter with SSR is analyzed, designed and tested. Experimental results show that the operating frequency could be as high as 4MHz and the efficiency could be improved by more than 10% compared to that when a hyper fast diode rectifier is used. Based on a new current-source gate driver scheme, an integrated gate driver for buck converter is also developed in this work by using a 0.35µm CMOS process with optional high voltage (50V) power MOSFET. The integrated gate driver consists both the current-source driver for high-side power MOSFET and low-power driver for low-side power iv MOSFET. Compared with the conventional gate driver circuit, the current-source gate driver can recovery some gate charging energy and reduce switching loss. So the current-source driver (CSD) can be used to improve the efficiency performance in high frequency power converters. This work also presents a new implementation of a power supply in package (PSiP) 5MHz buck converter, which is different from all the prior-of-art PSiP solutions by using a high-Q bondwire inductor. The high-Q bondwire inductor can be manufactured by applying ferrite epoxy to the common bondwire during standard IC packaging process, so the new implementation of PSiP is expected to be a cost-effective way of power supply integration