고속 시리얼 링크를 위한 고리 발진기를 기반으로 하는 주파수 합성기

학위논문(박사) -- 서울대학교대학원 : 공과대학 전기·정보공학부, 2022. 8. 정덕균.In this dissertation, major concerns in the clocking of modern serial links are discussed. As sub-rate, multi-standard architectures are becoming predominant, the conventional clocking methodology seems to necessitate innovation in terms of low-cost implementation. Frequency synthesis with active, inductor-less oscillators replacing LC counterparts are reviewed, and solutions for two major drawbacks are proposed. Each solution is verified by prototype chip design, giving a possibility that the inductor-less oscillator may become a proper candidate for future high-speed serial links. To mitigate the high flicker noise of a high-frequency ring oscillator (RO), a reference multiplication technique that effectively extends the bandwidth of the following all-digital phase-locked loop (ADPLL) is proposed. The technique avoids any jitter accumulation, generating a clean mid-frequency clock, overall achieving high jitter performance in conjunction with the ADPLL. Timing constraint for the proper reference multiplication is first analyzed to determine the calibration points that may correct the existent phase errors. The weight for each calibration point is updated by the proposed a priori probability-based least-mean-square (LMS) algorithm. To minimize the time required for the calibration, each gain for the weight update is adaptively varied by deducing a posteriori which error source dominates the others. The prototype chip is fabricated in a 40-nm CMOS technology, and its measurement results verify the low-jitter, high-frequency clock generation with fast calibration settling. The presented work achieves an rms jitter of 177/223 fs at 8/16-GHz output, consuming 12.1/17-mW power. As the second embodiment, an RO-based ADPLL with an analog technique that addresses the high supply sensitivity of the RO is presented. Unlike prior arts, the circuit for the proposed technique does not extort the RO voltage headroom, allowing high-frequency oscillation. Further, the performance given from the technique is robust over process, voltage, and temperature (PVT) variations, avoiding the use of additional calibration hardware. Lastly, a comprehensive analysis of phase noise contribution is conducted for the overall ADPLL, followed by circuit optimizations, to retain the low-jitter output. Implemented in a 40-nm CMOS technology, the frequency synthesizer achieves an rms jitter of 289 fs at 8 GHz output without any injected supply noise. Under a 20-mVrms white supply noise, the ADPLL suppresses supply-noise-induced jitter by -23.8 dB.본 논문은 현대 시리얼 링크의 클락킹에 관여되는 주요한 문제들에 대하여 기술한다. 준속도, 다중 표준 구조들이 채택되고 있는 추세에 따라, 기존의 클라킹 방법은 낮은 비용의 구현의 관점에서 새로운 혁신을 필요로 한다. LC 공진기를 대신하여 능동 소자 발진기를 사용한 주파수 합성에 대하여 알아보고, 이에 발생하는 두가지 주요 문제점과 각각에 대한 해결 방안을 탐색한다. 각 제안 방법을 프로토타입 칩을 통해 그 효용성을 검증하고, 이어서 능동 소자 발진기가 미래의 고속 시리얼 링크의 클락킹에 사용될 가능성에 대해 검토한다. 첫번째 시연으로써, 고주파 고리 발진기의 높은 플리커 잡음을 완화시키기 위해 기준 신호를 배수화하여 뒷단의 위상 고정 루프의 대역폭을 효과적으로 극대화 시키는 회로 기술을 제안한다. 본 기술은 지터를 누적 시키지 않으며 따라서 깨끗한 중간 주파수 클락을 생성시켜 위상 고정 루프와 함께 높은 성능의 고주파 클락을 합성한다. 기준 신호를 성공적으로 배수화하기 위한 타이밍 조건들을 먼저 분석하여 타이밍 오류를 제거하기 위한 방법론을 파악한다. 각 교정 중량은 연역적 확률을 기반으로한 LMS 알고리즘을 통해 갱신되도록 설계된다. 교정에 필요한 시간을 최소화 하기 위하여, 각 교정 이득은 타이밍 오류 근원들의 크기를 귀납적으로 추론한 값을 바탕으로 지속적으로 제어된다. 40-nm CMOS 공정으로 구현된 프로토타입 칩의 측정을 통해 저소음, 고주파 클락을 빠른 교정 시간안에 합성해 냄을 확인하였다. 이는 177/223 fs의 rms 지터를 가지는 8/16 GHz의 클락을 출력한다. 두번째 시연으로써, 고리 발진기의 높은 전원 노이즈 의존성을 완화시키는 기술이 포함된 주파수 합성기가 설계되었다. 이는 고리 발진기의 전압 헤드룸을 보존함으로서 고주파 발진을 가능하게 한다. 나아가, 전원 노이즈 감소 성능은 공정, 전압, 온도 변동에 대하여 민감하지 않으며, 따라서 추가적인 교정 회로를 필요로 하지 않는다. 마지막으로, 위상 노이즈에 대한 포괄적 분석과 회로 최적화를 통하여 주파수 합성기의 저잡음 출력을 방해하지 않는 방법을 고안하였다. 해당 프로토타입 칩은 40-nm CMOS 공정으로 구현되었으며, 전원 노이즈가 인가되지 않은 상태에서 289 fs의 rms 지터를 가지는 8 GHz의 클락을 출력한다. 또한, 20 mVrms의 전원 노이즈가 인가되었을 때에 유도되는 지터의 양을 -23.8 dB 만큼 줄이는 것을 확인하였다.1 Introduction 1 1.1 Motivation 3 1.1.1 Clocking in High-Speed Serial Links 4 1.1.2 Multi-Phase, High-Frequency Clock Conversion 8 1.2 Dissertation Objectives 10 2 RO-Based High-Frequency Synthesis 12 2.1 Phase-Locked Loop Fundamentals 12 2.2 Toward All-Digital Regime 15 2.3 RO Design Challenges 21 2.3.1 Oscillator Phase Noise 21 2.3.2 Challenge 1: High Flicker Noise 23 2.3.3 Challenge 2: High Supply Noise Sensitivity 26 3 Filtering RO Noise 28 3.1 Introduction 28 3.2 Proposed Reference Octupler 34 3.2.1 Delay Constraint 34 3.2.2 Phase Error Calibration 38 3.2.3 Circuit Implementation 51 3.3 IL-ADPLL Implementation 55 3.4 Measurement Results 59 3.5 Summary 63 4 RO Supply Noise Compensation 69 4.1 Introduction 69 4.2 Proposed Analog Closed Loop for Supply Noise Compensation 72 4.2.1 Circuit Implementation 73 4.2.2 Frequency-Domain Analysis 76 4.2.3 Circuit Optimization 81 4.3 ADPLL Implementation 87 4.4 Measurement Results 90 4.5 Summary 98 5 Conclusions 99 A Notes on the 8REF 102 B Notes on the ACSC 105박

Digital enhancement techniques for fractional-N frequency synthesizers

Meeting the demand for unprecedented connectivity in the era of internet-of-things (IoT) requires extremely energy efficient operation of IoT nodes to extend battery life. Managing the data traffic generated by trillions of such nodes also puts severe energy constraints on the data centers. Clock generators that are essential elements in these systems consume significant power and therefore must be optimized for low power and high performance. The focus of this thesis is on improving the energy efficiency of frequency synthesizers and clocking modules by exploring design techniques at both the architectural and circuit levels. In the first part of this work, a digital fractional-N phase locked loop (FNPLL) that employs a high resolution time-to-digital converter (TDC) and a truly ΔΣ fractional divider to achieve low in-band noise with a wide bandwidth is presented. The fractional divider employs a digital-to-time converter (DTC) to cancel out ΔΣ quantization noise in time domain, thus alleviating TDC dynamic range requirements. The proposed digital architecture adopts a narrow range low-power time-amplifier based TDC (TA-TDC) to achieve sub 1ps resolution. Fabricated in 65nm CMOS process, the prototype PLL achieves better than -106dBc/Hz in-band noise and 3MHz PLL bandwidth at 4.5GHz output frequency using 50MHz reference. The PLL achieves excellent jitter performance of 490fsrms, while consumes only 3.7mW. This translates to the best reported jitter-power figure-of-merit (FoM) of -240.5dB among previously reported FNPLLs. Phase noise performance of ring oscillator based digital FNPLLs is severely compromised by conflicting bandwidth requirements to simultaneously suppress oscillator phase and quantization noise introduced by the TDC, ΔΣ fractional divider, and digital-to-analog converter (DAC). As a consequence, their FoM that quantifies the power-jitter tradeoff is at least 25dB worse than their LC-oscillator based FNPLL counterparts. In the second part of this thesis, we seek to close this performance gap by extending PLL bandwidth using quantization noise cancellation techniques and by employing a dual-path digital loop filter to suppress the detrimental impact of DAC quantization noise. A prototype was implemented in a 65nm CMOS process operating over a wide frequency range of 2.0GHz-5.5GHz using a modified extended range multi-modulus divider with seamless switching. The proposed digital FNPLL achieves 1.9psrms integrated jitter while consuming only 4mW at 5GHz output. The measured in-band phase noise is better than -96 dBc/Hz at 1MHz offset. The proposed FNPLL achieves wide bandwidth up to 6MHz using a 50 MHz reference and its FoM is -228.5dB, which is at about 20dB better than previously reported ring-based digital FNPLLs. In the third part, we propose a new multi-output clock generator architecture using open loop fractional dividers for system-on-chip (SoC) platforms. Modern multi-core processors use per core clocking, where each core runs at its own speed. The core frequency can be changed dynamically to optimize for performance or power dissipation using a dynamic frequency scaling (DFS) technique. Fast frequency switching is highly desirable as long as it does not interrupt code execution; therefore it requires smooth frequency transitions with no undershoots. The second main requirement in processor clocking is the capability of spread spectrum frequency modulation. By spreading the clock energy across a wide bandwidth, the electromagnetic interference (EMI) is dramatically reduced. A conventional PLL clock generation approach suffers from a slow frequency settling and limited spread spectrum modulation capabilities. The proposed open loop fractional divider architecture overcomes the bandwidth limitation in fractional-N PLLs. The fractional divider switches the output frequency instantaneously and provides an excellent spread spectrum performance, where precise and programmable modulation depth and frequency can be applied to satisfy different EMI requirements. The fractional divider has unlimited modulation bandwidth resulting in spread spectrum modulation with no filtering, unlike fractional-N PLL; consequently it achieves higher EMI reduction. A prototype fractional divider was implemented in a 65nm CMOS process, where the measured peak-to-peak jitter is less than 27ps over a wide frequency range from 20MHz to 1GHz. The total power consumption is about 3.2mW for 1GHz output frequency. The all-digital implementation of the divider occupies the smallest area of 0.017mm2 compared to state-of-the-art designs. As the data rate of serial links goes higher, the jitter requirements of the clock generator become more stringent. Improving the jitter performance of conventional PLLs to less than (200fsrms) always comes with a large power penalty (tens of mWs). This is due to the PLL coupled noise bandwidth trade-off, which imposes stringent noise requirements on the oscillator and/or loop components. Alternatively, an injection-locked clock multiplier (ILCM) provides many advantages in terms of phase noise, power, and area compared to classical PLLs, but they suffer from a narrow lock-in range and a high sensitivity to PVT variations especially at a large multiplication factor (N). In the fourth part of this thesis, a low-jitter, low-power LC-based ILCM with a digital frequency-tracking loop (FTL) is presented. The proposed FTL relies on a new pulse gating technique to continuously tune the oscillator's free-running frequency. The FTL ensures robust operation across PVT variations and resolves the race condition existing in injection locked PLLs by decoupling frequency tuning from the injection path. As a result, the phase locking condition is only determined by the injection path. This work also introduces an accurate theoretical large-signal analysis for phase domain response (PDR) of injection locked oscillators (ILOs). The proposed PDR analysis captures the asymmetric nature of ILO's lock-in range, and the impact of frequency error on injection strength and phase noise performance. The proposed architecture and analysis are demonstrated by a prototype fabricated in 65 nm CMOS process with active area of 0.25mm2. The prototype ILCM multiplies the reference frequency by 64 to generate an output clock in the range of 6.75GHz-8.25GHz. A superior jitter performance of 190fsrms is achieved, while consuming only 2.25mW power. This translates to a best FoM of -251dB. Unlike conventional PLLs, ILCMs have been fundamentally limited to only integer-N operation and cannot synthesize fractional-N frequencies. In the last part of this thesis, we extend the merits of ILCMs to fractional-N and overcome this fundamental limitation. We employ DTC-based QNC techniques in order to align injected pulses to the oscillator's zero crossings, which enables it to pull the oscillator toward phase lock, thus realizing a fractional-N ILCM. Fabricated in 65nm CMOS process, a prototype 20-bit fractional-N ILCM with an output range of 6.75GHz-8.25GHz consumes only 3.25mW. It achieves excellent jitter performance of 110fsrms and 175fsrms in integer- and fractional-N modes respectively, which translates to the best-reported FoM in both integer- (-255dB) and fractional-N (-252dB) modes. The proposed fractional-N ILCM also features the first-reported rapid on/off capability, where the transient absolute jitter performance at wake-up is bounded below 4ps after less than 4ns. This demonstrates almost instantaneous phase settling. This unique capability enables tremendous energy saving by turning on the clock multiplier only when needed. This energy proportional operation leverages idle times to save power at the system-level of wireline and wireless transceivers

Frequency Synthesizers and Oscillator Architectures Based on Multi-Order Harmonic Generation

Frequency synthesizers are essential components for modern wireless and wireline communication systems as they provide the local oscillator signal required to transmit and receive data at very high rates. They are also vital for computing devices and microcontrollers as they generate the clocks required to run all the digital circuitry responsible for the high speed computations. Data rates and clocking speeds are continuously increasing to accommodate for the ever growing demand on data and computational power. This places stringent requirements on the performance metrics of frequency synthesizers. They are required to run at higher speeds, cover a wide range of frequencies, provide a low jitter/phase noise output and consume minimum power and area. In this work, we present new techniques and architectures for implementing high speed frequency synthesizers which fulfill the aforementioned requirements. We propose a new architecture and design approach for the realization of wideband millimeter-wave frequency synthesizers. This architecture uses two-step multi-order harmonic generation of a low frequency phase-locked signal to generate wideband mm-wave frequencies. A prototype of the proposed system is designed and fabricated in 90nm Complementary Metal Oxide Semiconductor (CMOS) technology. Measurement results demonstrated that a very wide tuning range of 5 to 32 GHz can be achieved, which is costly to implement using conventional techniques. Moreover the power consumption per octave resembles that of state-of-the art reports. Next, we propose the N-Push cyclic coupled ring oscillator (CCRO) architecture to implement two high performance oscillators: (1) a wideband N-Push/M-Push CCRO operating from 3.16-12.8GHz implemented by two harmonic generation operations using the availability of different phases from the CCRO, and (2) a 13-25GHz millimeter-wave N-Push CCRO with a low phase noise performance of -118dBc/Hz at 10MHz. The proposed oscillators achieve low phase noise with higher FOM than state of the art work. Finally, we present some improvement techniques applied to the performance of phase locked loops (PLLs). We present an adaptive low pass filtering technique which can reduce the reference spur of integer-N charge-pump based PLLs by around 20dB while maintaining the settling time of the original PLL. Another PLL is presented, which features very low power consumption targeting the Medical Implantable Communication Standard. It operates at 402-405 MHz while consuming 600microW from a 1V supply

LOW-POWER FREQUENCY SYNTHESIS BASED ON INJECTION LOCKING

Ph.DDOCTOR OF PHILOSOPH

Ultra-Wideband Transceiver with Error Correction for Cortical Interfaces in NanometerCMOS Process

This dissertation reports a high-speed wideband wireless transmission solution for the tight power constraints of cortical interface application. The proposed system deploysImpulse Radio Ultra-wideband (IR-UWB) technique to achieve very high-rate communication. However, impulse radio signals suffer from significant attenuation within the body,and power limitations force the use of very low-power receiver circuits which introduce additional noise and jitter. Moreover, the coils’ self-resonance has to be suppressed to minimize the pulse distortion and inter-symbol interference, adding significant attenuation. To compensate these losses, an Error correction code (ECC) layer is added for functioning reliably to the system. The performance evaluation is made by modeling a pair of physically fabricated coils, and the results show that the ECC is essential to obtain the system’s reliability. Furthermore, the gm/ID methodology, which is based on the complete exploration ofall inversion regions that the transistors are biased, is studied and explored for optimizingthe system at the circuit-level. Specific focuses are on the RF blocks: the low noise am-plifier (LNA) and the injection-locked voltage controlled oscillator (IL-VCO). Through the analytical deduction of the circuit’s features as the function of the gm/ID for each transistor, it is possible to select the optimum operating region for the circuit to achieve the target specification. Other circuit blocks, including the phase shifter, frequency divider,mixer, etc. are also described and analyzed. The prototype is fabricated in a 65-nm CMOS(Complementary Metal-Oxide-Semiconductor) process

Design of High-Speed SerDes Transceiver for Chip-to-Chip Communications in CMOS Process

With the continuous increase of on-chip computation capacities and exponential growth of data-intensive applications, the high-speed data transmission through serial links has become the backbone for modern communication systems. To satisfy the massive data-exchanging requirement, the data rate of such serial links has been updated from several Gb/s to tens of Gb/s. Currently, the commercial standards such as Ethernet 400GbE, InfiniBand high data rate (HDR), and common electrical interface (CEI)-56G has been developing towards 40+ Gb/s. As the core component within these links, the transceiver chipset plays a fundamental role in balancing the operation speed, power consumption, area occupation, and operation range. Meanwhile, the CMOS process has become the dominant technology in modern transceiver chip fabrications due to its large-scale digital integration capability and aggressive pricing advantage. This research aims to explore advanced techniques that are capable of exploiting the maximum operation speed of the CMOS process, and hence provides potential solutions for 40+ Gb/s CMOS transceiver designs. The major contributions are summarized as follows. A low jitter ring-oscillator-based injection-locked clock multiplier (RILCM) with a hybrid frequency tracking loop that consists of a traditional phase-locked loop (PLL), a timing-adjusted loop, and a loop selection state-machine is implemented in 65-nm C-MOS process. In the ring voltage-controlled oscillator, a full-swing pseudo-differential delay cell is proposed to lower the device noise to phase noise conversion. To obtain high operation speed and high detection accuracy, a compact timing-adjusted phase detector tightly combined with a well-matched charge pump is designed. Meanwhile, a lock-loss detection and lock recovery is devised to endow the RILCM with a similar lock-acquisition ability as conventional PLL, thus excluding the initial frequency set- I up aid and preventing the potential lock-loss risk. The experimental results show that the figure-of-merit of the designed RILCM reaches -247.3 dB, which is better than previous RILCMs and even comparable to the large-area LC-ILCMs. The transmitter (TX) and receiver (RX) chips are separately designed and fab- ricated in 65-nm CMOS process. The transmitter chip employs a quarter-rate multi-multiplexer (MUX)-based 4-tap feed-forward equalizer (FFE) to pre-distort the output. To increase the maximum operating speed, a bandwidth-enhanced 4:1 MUX with the capability of eliminating charge-sharing effect is proposed. To produce the quarter-rate parallel data streams with appropriate delays, a compact latch array associated with an interleaved-retiming technique is designed. The receiver chip employs a two-stage continuous-time linear equalizer (CTLE) as the analog front-end and integrates an improved clock data recovery to extract the sampling clocks and retime the incoming data. To automatically balance the jitter tracking and jitter suppression, passive low-pass filters with adaptively-adjusted bandwidth are introduced into the data-sampling path. To optimize the linearity of the phase interpolation, a time-averaging-based compensating phase interpolator is proposed. For equalization, a combined TX-FFE and RX-CTLE is applied to compensate for the channel loss, where a low-cost edge-data correlation-based sign zero-forcing adaptation algorithm is proposed to automatically adjust the TX-FFE’s tap weights. Measurement results show that the fabricated transmitter/receiver chipset can deliver 40 Gb/s random data at a bit error rate of 16 dB loss at the half-baud frequency, while consuming a total power of 370 mW

저전력, 저면적 유선 송수신기 설계를 위한 회로 기술

학위논문 (박사)-- 서울대학교 대학원 : 전기·컴퓨터공학부, 2016. 8. 정덕균.In this thesis, novel circuit techniques for low-power and area-efficient wireline transceiver, including a phase-locked loop (PLL) based on a two-stage ring oscillator, a scalable voltage-mode transmitter, and a forwarded-clock (FC) receiver based on a delay-locked-loop (DLL) based per-pin deskew, are proposed. At first, a two-stage ring PLL that provides a four-phase, high-speed clock for a quarter-rate TX in order to minimize power consumption is presented. Several analyses and verification techniques, ranging from the clocking architectures for a high-speed TX to oscillation failures in a two-stage ring oscillator, are addressed in this thesis. A tri-state-inverter–based frequency-divider and an AC-coupled clock-buffer are used for high-speed operations with minimal power and area overheads. The proposed PLL fabricated in the 65-nm CMOS technology occupies an active area of 0.009 mm2 with an integrated-RMS-jitter of 414 fs from 10 kHz to 100 MHz while consuming 7.6 mW from a 1.2-V supply at 10 GHz. The resulting figure-of-merit is -238.8 dB, which surpasses that of the state-of-the-art ring-PLLs by 4 dB. Secondly, a voltage-mode (VM) transmitter which offers a wide operation range of 6 to 32 Gb/s, controllable pre-emphasis equalization and output voltage swing without altering output impedance, and a power supply scalability is presented. A quarter-rate clocking architecture is employed in order to maximize the scalability and energy efficiency across the variety of operating conditions. A P-over-N VM driver is used for CMOS compatibility and wide voltage-swing range required for various I/O standards. Two supply regulators calibrate the output impedance of the VM driver across the wide swing and pre-emphasis range. A single phase-locked loop is used to provide a wide frequency range of 1.5-to-8 GHz. The prototype chip is fabricated in 65-nm CMOS technology and occupies active area of 0.48x0.36 mm2. The proposed transmitter achieves 250-to-600-mV single-ended swing and exhibits the energy efficiency of 2.10-to-2.93 pJ/bit across the data rate of 6-to-32 Gb/s. And last, this thesis describes a power and area-efficient FC receiver and includes an analysis of the jitter tolerance of the FC receiver. In the proposed design, jitter tolerance is maximized according to the analysis by employing a DLL-based de-skewing. A sample-swapping bang-bang phase-detector (SS-BBPD) eliminates the stuck locking caused by the finite delay range of the voltage-controlled delay line (VCDL), and also reduces the required delay range of the VCDL by half. The proposed FC receiver is fabricated in 65-nm CMOS technology and occupies an active area of 0.025 mm2. At a data rate of 12.5 Gb/s, the proposed FC receiver exhibits an energy efficiency of 0.36 pJ/bit, and tolerates 1.4-UIpp sinusoidal jitter of 300 MHz.Chapter 1. Introduction 1 1.1. Motivation 1 1.2. Thesis organization 5 Chapter 2. Phase-Locked Loop Based on Two-Stage Ring Oscillator 7 2.1. Overivew 7 2.2. Background and Analysis of a Two-stage Ring Oscillator 11 2.3. Circuit Implementation of The Proposed PLL 25 2.4. Measurement Results 33 Chapter 3. A Scalable Voltage-Mode Transmitter 37 3.1. Overview 37 3.2. Design Considerations on a Scalable Serial Link Transmitter 40 3.3. Circuit Implementation 46 3.4. Measurement Results 56 Chapter 4. Delay-Locked Loop Based Forwarded-Clock Receiver 62 4.1. Overview 62 4.2. Timing and Data Recovery in a Serial Link 65 4.3. DLL-Based Forwarded-Clock Receiver Characteristics 70 4.4. Circuit Implementation 79 4.5. Measurement Results 89 Chapter 5. Conclusion 94 Appendix 96 Appendix A. Design flow to optimize a high-speed ring oscillator 96 Appendix B. Reflection Issues in N-over-N Voltage-Mode Driver 99 Appendix C. Analysis on output swing and power consumption of the P-over-N voltage-mode driver 107 Appendix D. Loop Dynamics of DLL 112 Bibliography 121 Abstract 128Docto

A high speed serializer/deserializer design

A Serializer/Deserializer (SerDes) is a circuit that converts parallel data into a serial stream and vice versa. It helps solve clock/data skew problems, simplifies data transmission, lowers the power consumption and reduces the chip cost. The goal of this project was to solve the challenges in high speed SerDes design, which included the low jitter design, wide bandwidth design and low power design. A quarter-rate multiplexer/demultiplexer (MUX/DEMUX) was implemented. This quarter-rate structure decreases the required clock frequency from one half to one quarter of the data rate. It is shown that this significantly relaxes the design of the VCO at high speed and achieves lower power consumption. A novel multi-phase LC-ring oscillator was developed to supply a low noise clock to the SerDes. This proposed VCO combined an LC-tank with a ring structure to achieve both wide tuning range (11%) and low phase noise (-110dBc/Hz at 1MHz offset). With this structure, a data rate of 36 Gb/s was realized with a measured peak-to-peak jitter of 10ps using 0.18microm SiGe BiCMOS technology. The power consumption is 3.6W with 3.4V power supply voltage. At a 60 Gb/s data rate the simulated peak-to-peak jitter was 4.8ps using 65nm CMOS technology. The power consumption is 92mW with 2V power supply voltage. A time-to-digital (TDC) calibration circuit was designed to compensate for the phase mismatches among the multiple phases of the PLL clock using a three dimensional fully depleted silicon on insulator (3D FDSOI) CMOS process. The 3D process separated the analog PLL portion from the digital calibration portion into different tiers. This eliminated the noise coupling through the common substrate in the 2D process. Mismatches caused by the vertical tier-to-tier interconnections and the temperature influence in the 3D process were attenuated by the proposed calibration circuit. The design strategy and circuits developed from this dissertation provide significant benefit to both wired and wireless applications

Customer premise service study for 30/20 GHz satellite system

Satellite systems in which the space segment operates in the 30/20 GHz frequency band are defined and compared as to their potential for providing various types of communications services to customer premises and the economic and technical feasibility of doing so. Technical tasks performed include: market postulation, definition of the ground segment, definition of the space segment, definition of the integrated satellite system, service costs for satellite systems, sensitivity analysis, and critical technology. Based on an analysis of market data, a sufficiently large market for services is projected so as to make the system economically viable. A large market, and hence a high capacity satellite system, is found to be necessary to minimize service costs, i.e., economy of scale is found to hold. The wide bandwidth expected to be available in the 30/20 GHz band, along with frequency reuse which further increases the effective system bandwidth, makes possible the high capacity system. Extensive ground networking is required in most systems to both connect users into the system and to interconnect Earth stations to provide spatial diversity. Earth station spatial diversity is found to be a cost effective means of compensating the large fading encountered in the 30/20 GHz operating band