ULTRA LOW POWER FSK RECEIVER AND RF ENERGY HARVESTER

This thesis focuses on low power receiver design and energy harvesting techniques as methods for intelligently managing energy usage and energy sources. The goal is to build an inexhaustibly powered communication system that can be widely applied, such as through wireless sensor networks (WSNs). Low power circuit design and smart power management are techniques that are often used to extend the lifetime of such mobile devices. Both methods are utilized here to optimize power usage and sources. RF energy is a promising ambient energy source that is widely available in urban areas and which we investigate in detail. A harvester circuit is modeled and analyzed in detail at low power input. Based on the circuit analysis, a design procedure is given for a narrowband energy harvester. The antenna and harvester co-design methodology improves RF to DC energy conversion efficiency. The strategy of co-design of the antenna and the harvester creates opportunities to optimize the system power conversion efficiency. Previous surveys have found that ambient RF energy is spread broadly over the frequency domain; however, here it is demonstrated that it is theoretically impossible to harvest RF energy over a wide frequency band if the ambient RF energy source(s) are weak, owing to the voltage requirements. It is found that most of the ambient RF energy lies in a series of narrow bands. Two different versions of harvesters have been designed, fabricated, and tested. The simulated and measured results demonstrate a dual-band energy harvester that obtains over 9% efficiency for two different bands (900MHz and 1800MHz) at an input power as low as -19dBm. The DC output voltage of this harvester is over 1V, which can be used to recharge the battery to form an inexhaustibly powered communication system. A new phase locked loop based receiver architecture is developed to avoid the significant conversion losses associated with OOK architectures. This also helps to minimize power consumption. A new low power mixer circuit has also been designed, and a detailed analysis is provided. Based on the mixer, a low power phase locked loop (PLL) based receiver has been designed, fabricated and measured. A power management circuit and a low power transceiver system have also been co-designed to provide a system on chip solution. The low power voltage regulator is designed to handle a variety of battery voltage, environmental temperature, and load conditions. The whole system can work with a battery and an application specific integrated circuit (ASIC) as a sensor node of a WSN network

A Low Phase Noise Wide-Tuning Range Class-F VCO Based on a Dual-Mode Resonator in 65nm CMOS

A Voltage Controlled Oscillator (VCO) is a critical building block in the design of current frequency synthesizers for RF system applications. State-of-the-art operation defines that an oscillator should have the best spectral purity while consuming low amount of power for a wide tuning range. With this in mind, this work presents a low phase noise wide tuning range ClassF VCO using a dual-mode resonator. In comparison to other conventional wideband oscillators, the proposed capacitively/inductively-coupled resonator will integrate the benefits of Class-F voltage control oscillators and dual-mode switching networks to obtain simultaneous low phase noise and wide-tuning range. The proposed structure, prototyped in 65nm TSMC CMOS technology, shows a 2.14 – 4.22GHz continuous tuning range, phase noise figure-of-merit (FoM) of 192.7dB at 2.3GHz and better than 188dB across the entire operating frequency range. The oscillator consumes 15-16.4mW from a 0.6V supply and occupies an active area of 0.7mm^2 . In conclusion, the proposed resonator achieves 2- 3dB phase noise improvement while achieving 65% overall tuning range when compared to a typical class-F VCO architecture

In-field Built-in Self-test for Measuring RF Transmitter Power and Gain

abstract: RF transmitter manufacturers go to great extremes and expense to ensure that their product meets the RF output power requirements for which they are designed. Therefore, there is an urgent need for in-field monitoring of output power and gain to bring down the costs of RF transceiver testing and ensure product reliability. Built-in self-test (BIST) techniques can perform such monitoring without the requirement for expensive RF test equipment. In most BIST techniques, on-chip resources, such as peak detectors, power detectors, or envelope detectors are used along with frequency down conversion to analyze the output of the design under test (DUT). However, this conversion circuitry is subject to similar process, voltage, and temperature (PVT) variations as the DUT and affects the measurement accuracy. So, it is important to monitor BIST performance over time, voltage and temperature, such that accurate in-field measurements can be performed. In this research, a multistep BIST solution using only baseband signals for test analysis is presented. An on-chip signal generation circuit, which is robust with respect to time, supply voltage, and temperature variations is used for self-calibration of the BIST system before the DUT measurement. Using mathematical modelling, an analytical expression for the output signal is derived first and then test signals are devised to extract the output power of the DUT. By utilizing a standard 180nm IBM7RF CMOS process, a 2.4GHz low power RF IC incorporated with the proposed BIST circuitry and on-chip test signal source is designed and fabricated. Experimental results are presented, which show this BIST method can monitor the DUT’s output power with +/- 0.35dB accuracy over a 20dB power dynamic range.Dissertation/ThesisMasters Thesis Electrical Engineering 201

An enhanced swing differential Colpitts CMOS VCO for low-voltage operation

An enhanced swing differential Colpitts VCO (ESDC-VCO) dramatically improves the swing of a Colpitts VCO by allowing the signal to swing below ground and above the supply voltage. Fabricated in a 1P8M 0.13 um CMOS process, the ESDC-VCO operates at 4.9GHz with a 0.475-V supply and consumes 2.7mW. The measured phase noise is -136.2 dBc/Hz at a 3-MHz frequency offset. The ESDC-VCO employs digital amplitude control and achieves a Figure of merit (FOM) of 196.2 dBc/Hz, making it the highest performing integrated LC oscillator to date

High performance RF and baseband building blocks for wireless receivers

Because of the unique architecture of wireless receivers, a designer must understand both the high frequency aspects as well as the low-frequency analog considerations for different building blocks of the receiver. The primary goal of this research work is to explore techniques for implementing high performance RF and baseband building blocks for wireless applications. Several novel techniques to improve the performance of analog building blocks are presented. An enhanced technique to couple two LC resonators is presented which does not degrade the loaded quality factor of the resonators which results in an increased dynamic range. A novel technique to automatically tune the quality factor of LC resonators is presented. The proposed scheme is stable and fast and allows programming both the quality factor and amplitude response of the LC filter. To keep the oscillation amplitude of LC VCOs constant and thus achieving a minimum phase noise and a reliable startup, a stable amplitude control loop is presented. The proposed scheme has been also used in a master-slave quality factor tuning of LC filters. An efficient and low-cost architecture for a 3.1GHz-10.6GHz ultra-wide band frequency synthesizer is presented. The proposed scheme is capable of generating 14A novel pseudo-differential transconductance amplifier is presented. The proposed scheme takes advantage of the second-order harmonic available at the output current of pseudo-differential structure to cancel the third-order harmonic distortion. A novel nonlinear function is proposed which inherently removes the third and the fifth order harmonics at its output signal. The proposed nonlinear block is used in a bandpass-based oscillator to generate a highly linear sinusoidal output. Finally, a linearized BiCMOS transconductance amplifier is presented. This transconductance is used to build a third-order linear phase low pass filter with a cut-off frequency of 264MHz for an ultra-wide band receiver. carrier frequencies

A Low Jitter Wideband Fractional-N Subsampling Phase Locked Loop (SSPLL)

Frequency synthesizers have become a crucial building block in the evolution of modern communication systems and consumer electronics. The spectral purity performance of frequency synthesizers limits the achievable data-rate and presents a noise-power tradeoff. For communication standards such as LTE where the channel spacing is a few kHz, the synthesizers must provide high frequencies with sufficiently wide frequency tuning range and fine frequency resolutions. Such stringent performance must be met with a limited power and small chip area. In this thesis a wideband fractional-N frequency synthesizer based on a subsampling phase locked loop (SSPLL) is presented. The proposed synthesizer which has a frequency resolution less than 100Hz employs a digital fractional controller (DFC) and a 10-bit digital-to-time converter (DTC) to delay the rising edges of the reference clock to achieve fractional phase lock. For fast convergence of the delay calibration, a novel two-step delay correlation loop (DCL) is employed. Furthermore, to provide optimum settling and jitter performance, the loop transfer characteristics during frequency acquisition and phase-lock are decoupled using a dual input loop filter (DILF). The fractional-N sub-sampling PLL (FNSSPLL) is implemented in a TSMC 40nm CMOS technology and occupies a total active area of 0.41mm^2. The PLL operates over frequency range of 2.8 GHz to 4.3 GHz (42% tuning range) while consuming 9.18mW from a 1.1V supply. The integrated jitter performance is better than 390 fs across all fractional frequency channel. The worst case fractional spur of -48.3 dBc occurs at a 650 kHz offset for a 3.75GHz fractional channel. The in-band phase noise measured at a 200 kHz offset is -112.5 dBc/Hz

Clock multiplication techniques for high-speed I/Os

Generation of a low-jitter, high-frequency clock from a low-frequency reference clock using classical analog phase-locked loops (PLLs) requires a large loop filter capacitor and power hungry oscillator. Digital PLLs can help reduce area but their jitter performance is severely degraded by quantization error. In this dissertation different clock multiplication techniques have been explored that can be suitable for high-speed wireline systems. With the emphasis on ring oscillator based architecture using cascaded stages, three possible architectures are explored. First, a scrambling TDC (STDC) is presented to improve deterministic jitter (DJ) performance when used with a low-frequency reference clock. A cascaded architecture with digital multiplying delay locked loop as the first stage and hybrid analog/digital PLL as the second stage is used to achieve low random jitter in a power efficient manner. Fabricated in a 90nm CMOS process, the prototype frequency synthesizer consumes 4.76mW power from a 1.0V supply and generates 160MHz and 2.56 GHz output clocks from a 1.25MHz crystal reference frequency. The long-term absolute jitter of the 60MHz digital MDLL and 2.56 GHz digital PLL outputs are 2.4 psrms and 4.18 psrms, while the peak-to-peak jitter is 22.1 ps and 35.2 ps, respectively. The proposed frequency synthesizer occupies an active die area of 0.16mm2 and achieves power efficiency of 1.86 mW/GHz. Second, a hybrid phase/current-mode phase interpolator (HPC-PI) is presented to improve phase noise performance of ring oscillator-based fractional-N PLLs. The proposed HPC-PI alleviates the bandwidth trade-off between VCO phase noise suppression and ΔΣ quantization noise suppression. By combining the phase detection and interpolation functions into an XOR phase detector/interpolator (XOR PD-PI) block, accurate quantization error cancellation is achieved without using calibration. Use of a digital MDLL in front of the fractional-N PLL helps in alleviating the bandwidth limitation due to reference frequency and enables bandwidth extension even further. The extended bandwidth helps in suppressing the ring-VCO phase noise and lowering the in-band noise floor. Fabricated in 65nm CMOS process, the prototype generates fractional frequencies from 4.25 to 4.75 GHz, with an in-band phase noise floor of -104 dBc/Hz and 1.5 psrms integrated jitter. The clock multiplier achieves power efficiency of 2.4mW/GHz and FoM of -225.8 dB. Finally, an efficient clock generation, recovery, and distribution techniques for flexible-rate transceivers are presented. Using a fixed-frequency low-jitter clock provided by an integer-N PLL, fractional frequencies are generated/recovered locally using multi-phase fractional clock multipliers. Fabricated in a 65nm CMOS, the prototype transceiver can be programmed to operate at any rate from 3-to-10 Gb/s. At 10 Gb/s, integrated jitter of the Tx output and recovered clock is 360 fsrms and 758 fsrms, respectively

Characterization of process variability and robust optimization of analog circuits

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2008.Includes bibliographical references (p. 161-174).Continuous scaling of CMOS technology has enabled dramatic performance enhancement of CMOS devices and has provided speed, power, and density improvement in both digital and analog circuits. CMOS millimeter-wave applications operating at more than 50GHz frequencies has become viable in sub-100nm CMOS technologies, providing advantages in cost and high density integration compared to other heterogeneous technologies such as SiGe and III-V compound semiconductors. However, as the operating frequency of CMOS circuits increases, it becomes more difficult to obtain sufficiently wide operating ranges for robust operation in essential analog building blocks such as voltage-controlled oscillators (VCOs) and frequency dividers. The fluctuations of circuit parameters caused by the random and systematic variations in key manufacturing steps become more significant in nano-scale technologies. The process variation of circuit performance is quickly becoming one of the main concerns in high performance analog design. In this thesis, we show design and analysis of a VCO and frequency divider operating beyond 70GHz in a 65nm SOI CMOS technology. The VCO and frequency divider employ design techniques enlarging frequency operating ranges to improve the robustness of circuit operation. Circuit performance is measured from a number of die samples to identify the statistical properties of performance variation. A back-propagation of variation (BPV) scheme based on sensitivity analysis of circuit performance is proposed to extract critical circuit parameter variation using statistical measurement results of the frequency divider. We analyze functional failure caused by performance variability, and propose dynamic and static optimization methods to improve parametric yield. An external bias control is utilized to dynamically tune the divider operating range and to compensate for performance variation. A novel time delay model of a differential CML buffer is proposed to functionally approximate the maximum operating frequency of the frequency divider, which dramatically reduces computational cost of parametric yield estimation. The functional approximation enables the optimization of the VCO and frequency divider parametric yield with a reasonable amount of simulation time.by Daihyun Lim.Ph.D

準ミリ波・ミリ波領域における低位相雑音電圧制御発振器のLC共振器に関する研究

2017岡山県立大学大学