Design of energy efficient high speed I/O interfaces

Energy efficiency has become a key performance metric for wireline high speed I/O interfaces. Consequently, design of low power I/O interfaces has garnered large interest that has mostly been focused on active power reduction techniques at peak data rate. In practice, most systems exhibit a wide range of data transfer patterns. As a result, low energy per bit operation at peak data rate does not necessarily translate to overall low energy operation. Therefore, I/O interfaces that can scale their power consumption with data rate requirement are desirable. Rapid on-off I/O interfaces have a potential to scale power with data rate requirements without severely affecting either latency or the throughput of the I/O interface. In this work, we explore circuit techniques for designing rapid on-off high speed wireline I/O interfaces and digital fractional-N PLLs. A burst-mode transmitter suitable for rapid on-off I/O interfaces is presented that achieves 6 ns turn-on time by utilizing a fast frequency settling ring oscillator in digital multiplying delay-locked loop and a rapid on-off biasing scheme for current mode output driver. Fabricated in 90 nm CMOS process, the prototype achieves 2.29 mW/Gb/s energy efficiency at peak data rate of 8 Gb/s. A 125X (8 Gb/s to 64 Mb/s) change in effective data rate results in 67X (18.29 mW to 0.27 mW) change in transmitter power consumption corresponding to only 2X (2.29 mW/Gb/s to 4.24 mW/Gb/s) degradation in energy efficiency for 32-byte long data bursts. We also present an analytical bit error rate (BER) computation technique for this transmitter under rapid on-off operation, which uses MDLL settling measurement data in conjunction with always-on transmitter measurements. This technique indicates that the BER bathtub width for 10^(−12) BER is 0.65 UI and 0.72 UI during rapid on-off operation and always-on operation, respectively. Next, a pulse response estimation-based technique is proposed enabling burst-mode operation for baud-rate sampling receivers that operate over high loss channels. Such receivers typically employ discrete time equalization to combat inter-symbol interference. Implementation details are provided for a receiver chip, fabricated in 65nm CMOS technology, that demonstrates efficacy of the proposed technique. A low complexity pulse response estimation technique is also presented for low power receivers that do not employ discrete time equalizers. We also present techniques for implementation of highly digital fractional-N PLL employing a phase interpolator based fractional divider to improve the quantization noise shaping properties of a 1-bit ∆Σ frequency-to-digital converter. Fabricated in 65nm CMOS process, the prototype calibration-free fractional-N Type-II PLL employs the proposed frequency-to-digital converter in place of a high resolution time-to-digital converter and achieves 848 fs rms integrated jitter (1 kHz-30 MHz) and -101 dBc/Hz in-band phase noise while generating 5.054 GHz output from 31.25 MHz input

Design Techniques for Energy Efficient Multi-GB/S Serial I/O Transceivers

Total I/O bandwidth demand is growing in high-performance systems due to the emergence of many-core microprocessors and in mobile devices to support the next generation of multi-media features. High-speed serial I/O energy efficiency must improve in order to enable continued scaling of these parallel computing platforms in applications ranging from data centers to smart mobile devices. The first work, a low-power forwarded-clock I/O transceiver architecture is presented that employs a high degree of output/input multiplexing, supply-voltage scaling with data rate, and low-voltage circuit techniques to enable low-power operation. The transmitter utilizes a 4:1 output multiplexing voltage-mode driver along with 4-phase clocking that is efficiently generated from a passive poly-phase filter. The output driver voltage swing is accurately controlled from 100-200 mV_(ppd) using a low-voltage pseudo-differential regulator that employs a partial negative-resistance load for improved low frequency gain. 1:8 input de-multiplexing is performed at the receiver equalizer output with 8 parallel input samplers clocked from an 8-phase injection-locked oscillator that provides more than 1UI de-skew range. Low-power high-speed serial I/O transmitters which include equalization to compensate for channel frequency dependent loss are required to meet the aggressive link energy efficiency targets of future systems. The second work presents a low power serial link transmitter design that utilizes an output stage which combines a voltage-mode driver, which offers low static-power dissipation, and current-mode equalization, which offers low complexity and dynamic-power dissipation. The utilization of current-mode equalization decouples the equalization settings and termination impedance, allowing for a significant reduction in pre-driver complexity relative to segmented voltage-mode drivers. Proper transmitter series termination is set with an impedance control loop which adjusts the on-resistance of the output transistors in the driver voltage-mode portion. Further reductions in dynamic power dissipation are achieved through scaling the serializer and local clock distribution supply with data rate. Finally, it presents that a scalable quarter-rate transmitter employs an analog-controlled impedance-modulated 2-tap voltage-mode equalizer and achieves fast power-state transitioning with a replica-biased regulator and ILO clock generation. Capacitively-driven 2 mm global clock distribution and automatic phase calibration allows for aggressive supply scaling

Toward realizing power scalable and energy proportional high-speed wireline links

Growing computational demand and proliferation of cloud computing has placed high-speed serial links at the center stage. Due to saturating energy efficiency improvements over the last five years, increasing the data throughput comes at the cost of power consumption. Conventionally, serial link power can be reduced by optimizing individual building blocks such as output drivers, receiver, or clock generation and distribution. However, this approach yields very limited efficiency improvement. This dissertation takes an alternative approach toward reducing the serial link power. Instead of optimizing the power of individual building blocks, power of the entire serial link is reduced by exploiting serial link usage by the applications. It has been demonstrated that serial links in servers are underutilized. On average, they are used only 15% of the time, i.e. these links are idle for approximately 85% of the time. Conventional links consume power during idle periods to maintain synchronization between the transmitter and the receiver. However, by powering-off the link when idle and powering it back when needed, power consumption of the serial link can be scaled proportionally to its utilization. This approach of rapid power state transitioning is known as the rapid-on/off approach. For the rapid-on/off to be effective, ideally the power-on time, off-state power, and power state transition energy must all be close to zero. However, in practice, it is very difficult to achieve these ideal conditions. Work presented in this dissertation addresses these challenges. When this research work was started (2011-12), there were only a couple of research papers available in the area of rapid-on/off links. Systematic study or design of a rapid power state transitioning in serial links was not available in the literature. Since rapid-on/off with nanoseconds granularity is not a standard in any wireline communication, even the popular test equipment does not support testing any such feature, neither any formal measurement methodology was available. All these circumstances made the beginning difficult. However, these challenges provided a unique opportunity to explore new architectural techniques and identify trade-offs. The key contributions of this dissertation are as follows. The first and foremost contribution is understanding the underlying limitations of saturating energy efficiency improvements in serial links and why there is a compelling need to find alternative ways to reduce the serial link power. The second contribution is to identify potential power saving techniques and evaluate the challenges they pose and the opportunities they present. The third contribution is the design of a 5Gb/s transmitter with a rapid-on/off feature. The transmitter achieves rapid-on/off capability in voltage mode output driver by using a fast-digital regulator, and in the clock multiplier by accurate frequency pre-setting and periodic reference insertion. To ease timing requirements, an improved edge replacement logic circuit for the clock multiplier is proposed. Mathematical modeling of power-on time as a function of various circuit parameters is also discussed. The proposed transmitter demonstrates energy proportional operation over wide variations of link utilization, and is, therefore, suitable for energy efficient links. Fabricated in 90nm CMOS technology, the voltage mode driver, and the clock multiplier achieve power-on-time of only 2ns and 10ns, respectively. This dissertation highlights key trade-off in the clock multiplier architecture, to achieve fast power-on-lock capability at the cost of jitter performance. The fourth contribution is the design of a 7GHz rapid-on/off LC-PLL based clock multi- plier. The phase locked loop (PLL) based multiplier was developed to overcome the limita- tions of the MDLL based approach. Proposed temperature compensated LC-PLL achieves power-on-lock in 1ns. The fifth and biggest contribution of this dissertation is the design of a 7Gb/s embedded clock transceiver, which achieves rapid-on/off capability in LC-PLL, current-mode transmit- ter and receiver. It was the first reported design of a complete transceiver, with an embedded clock architecture, having rapid-on/off capability. Background phase calibration technique in PLL and CDR phase calibration logic in the receiver enable instantaneous lock on power-on. The proposed transceiver demonstrates power scalability with a wide range of link utiliza- tion and, therefore, helps in improving overall system efficiency. Fabricated in 65nm CMOS technology, the 7Gb/s transceiver achieves power-on-lock in less than 20ns. The transceiver achieves power scaling by 44x (63.7mW-to-1.43mW) and energy efficiency degradation by only 2.2x (9.1pJ/bit-to-20.5pJ/bit), when the effective data rate (link utilization) changes by 100x (7Gb/s-to-70Mb/s). The sixth and final contribution is the design of a temperature sensor to compensate the frequency drifts due to temperature variations, during long power-off periods, in the fast power-on-lock LC-PLL. The proposed self-referenced VCO-based temperature sensor is designed with all digital logic gates and achieves low supply sensitivity. This sensor is suitable for integration in processor and DRAM environments. The proposed sensor works on the principle of directly converting temperature information to frequency and finally to digital bits. A novel sensing technique is proposed in which temperature information is acquired by creating a threshold voltage difference between the transistors used in the oscillators. Reduced supply sensitivity is achieved by employing junction capacitance, and the overhead of voltage regulators and an external ideal reference frequency is avoided. The effect of VCO phase noise on the sensor resolution is mathematically evaluated. Fabricated in the 65nm CMOS process, the prototype can operate with a supply ranging from 0.85V to 1.1V, and it achieves a supply sensitivity of 0.034oC/mV and an inaccuracy of ±0.9oC and ±2.3oC from 0-100oC after 2-point calibration, with and without static nonlinearity correction, respectively. It achieves a resolution of 0.3oC, resolution FoM of 0.3(nJ/conv)res2 , and measurement (conversion) time of 6.5μs

Power-Proportional Optical Links

The continuous increase in data transfer rate in short-reach links, such as chip-to-chip and between servers within a data-center, demands high-speed links. As power efficiency becomes ever more important in these links, power-efficient optical links need to be designed. Power efficiency in a link can be achieved by enabling power-proportional communication over the serial link. In power-proportional links, the power dissipated by a link is proportional to the amount of data communicated. Normally, data-rate demand is not constant, and the peak data-rate is not required all the time. If a link is not adapted according to the data-rate demand, there will be a fixed power dissipation, and the power efficiency of the link will degrade during the sub-maximal link utilization. Adapting links to real-time data-rate requirements reduces power dissipation. Power proportionality is achieved by scaling the power of the serial link linearly with the link utilization, and techniques such as variable data-rate and burst-mode can be adopted for this purpose. Links whose data rate (and hence power dissipation) can be varied in response to system demands are proposed in this work. Past works have presented rapidly reconfigurable bandwidth in variable data-rate receivers, allowing lower power dissipation for lower data-rate operation. However, maintaining synchronization during reconfiguration was not possible since previous approaches have introduced changes in front-end delay when they are reconfigured. This work presents a technique that allows rapid bandwidth adjustment while maintaining a near-constant delay through the receiver suitable for a power-scalable variable data-rate optical link. Measurements of a fabricated integrated circuit (IC) show nearly constant energy per bit across a 2× variation in data rate while introducing less than 10 % of a unit interval (UI) of delay variation. With continuously increasing data communication in data-centers, parallel optical links with ever-increasing per-lane data rates are being used to meet overall throughput demands. Simultaneously, power efficiency is becoming increasingly important for these links since they do not transmit useful data all the time. The burst-mode solution for vertical-cavity surface-emitting laser (VCSEL)-based point-to-point communication can be used to improve links’ energy efficiency during low link activity. The burst-mode technique for VCSEL-based links has not yet been deployed commercially. Past works have presented burst-mode solutions for single-channel receivers, allowing lower power dissipation during low link activity and solutions for fast activation of the receivers. However, this work presents a novel technique that allows rapid activation of a front-end and fast locking of a clock-and-data-recovery (CDR) for a multi-channel parallel link, utilizing opportunities arising from the parallel nature of many VCSEL-based links. The idea has been demonstrated through electrical and optical measurements of a fabricated IC at 10 Gbps, which show fast data detection and activation of the circuitry within 49 UIs while allowing the front-end to achieve better energy efficiency during low link activity. Simulation results are also presented in support of the proposed technique which allows the CDR to lock within 26 UIs from when it is powered on

Performance Analysis For Wireless G (IEEE 802.11 G) And Wireless N (IEEE 802.11 N) In Outdoor Environment

This paper described an analysis the different capabilities and limitation of both IEEE technologies that has been utilized for data transmission directed to mobile device. In this work, we have compared an IEEE 802.11/g/n outdoor environment to know what technology is better. the comparison consider on coverage area (mobility), through put and measuring the interferences. The work presented here is to help the researchers to select the best technology depending of their deploying case, and investigate the best variant for outdoor. The tool used is Iperf software which is to measure the data transmission performance of IEEE 802.11n and IEEE 802.11g

Performance analysis for wireless G (IEEE 802.11G) and wireless N (IEEE 802.11N) in outdoor environment

This paper described an analysis the different capabilities and limitation of both IEEE technologies that has been utilized for data transmission directed to mobile device. In this work, we have compared an IEEE 802.11/g/n outdoor environment to know what technology is better. The comparison consider on coverage area (mobility), throughput and measuring the interferences. The work presented here is to help the researchers to select the best technology depending of their deploying case, and investigate the best variant for outdoor. The tool used is Iperf software which is to measure the data transmission performance of IEEE 802.11n and IEEE 802.11g

NOTIFICATION !!!

All the content of this special edition is retrieved from the conference proceedings published by the European Scientific Institute, ESI. http://eujournal.org/index.php/esj/pages/view/books The European Scientific Journal, ESJ, after approval from the publisher re publishes the papers in a Special edition

NOTIFICATION !!!

All the content of this special edition is retrieved from the conference proceedings published by the European Scientific Institute, ESI. http://eujournal.org/index.php/esj/pages/view/books The European Scientific Journal, ESJ, after approval from the publisher re publishes the papers in a Special edition

NOTIFICATION !!!

All the content of this special edition is retrieved from the conference proceedings published by the European Scientific Institute, ESI. http://eujournal.org/index.php/esj/pages/view/books The European Scientific Journal, ESJ, after approval from the publisher re publishes the papers in a Special edition

NOTIFICATION !!!

All the content of this special edition is retrieved from the conference proceedings published by the European Scientific Institute, ESI. http://eujournal.org/index.php/esj/pages/view/books The European Scientific Journal, ESJ, after approval from the publisher re publishes the papers in a Special edition