Energy Efficient RF Transmitter Design using Enhanced Breakdown Voltage SOI-CMOS Compatible MESFETs

abstract: The high cut-off frequency of deep sub-micron CMOS technologies has enabled the integration of radio frequency (RF) transceivers with digital circuits. However, the challenging point is the integration of RF power amplifiers, mainly due to the low breakdown voltage of CMOS transistors. Silicon-on-insulator (SOI) metal semiconductor field effect transistors (MESFETs) have been introduced to remedy the limited headroom concern in CMOS technologies. The MESFETs presented in this thesis have been fabricated on different SOI-CMOS processes without making any change to the standard fabrication steps and offer 2-30 times higher breakdown voltage than the MOSFETs on the same process. This thesis explains the design steps of high efficiency and wideband RF transmitters using the proposed SOI-CMOS compatible MESFETs. This task involves DC and RF characterization of MESFET devices, along with providing a compact Spice model for simulation purposes. This thesis presents the design of several SOI-MESFET RF power amplifiers operating at 433, 900 and 1800 MHz with ~40% bandwidth. Measurement results show a peak power added efficiency (PAE) of 55% and a peak output power of 22.5 dBm. The RF-PAs were designed to operate in Class-AB mode to minimize the linearity degradation. Class-AB power amplifiers lead to poor power added efficiency, especially when fed with signals with high peak to average power ratio (PAPR) such as wideband code division multiple access (W-CDMA). Polar transmitters have been introduced to improve the efficiency of RF-PAs at backed-off powers. A MESFET based envelope tracking (ET) polar transmitter was designed and measured. A low drop-out voltage regulator (LDO) was used as the supply modulator of this polar transmitter. MESFETs are depletion mode devices; therefore, they can be configured in a source follower configuration to have better stability and higher bandwidth that MOSFET based LDOs. Measurement results show 350 MHz bandwidth while driving a 10 pF capacitive load. A novel polar transmitter is introduced in this thesis to alleviate some of the limitations associated with polar transmitters. The proposed architecture uses the backgate terminal of a partially depleted transistor on SOI process, which relaxes the bandwidth and efficiency requirements of the envelope amplifier in a polar transmitter. The measurement results of the proposed transmitter demonstrate more than three times PAE improvement at 6-dB backed-off output power, compared to the traditional RF transmitters.Dissertation/ThesisPh.D. Electrical Engineering 201

Doctor of Philosophy

dissertationHigh speed wireless communication systems (e.g., long-term evolution (LTE), Wi-Fi) operate with high bandwidth and large peak-to-average power ratios (PAPRs). This is largely due to the use of orthogonal frequency division multiplexing (OFDM) modulation that is prevalent to maximize the spectral efficiency of the communication system. The power amplifier (PA) in the transmitter is the dominant energy consumer in the radio, largely because of the PAPR of the input signal. To reduce the energy consumption of the PA an amplifier that simultaneously achieves high efficiency and high linearity. Furthermore, to lower the cost for high volume production, it is desirable to achieve a complete System-on-Chip (SoC) integration. Linear amplifiers (e.g., Class-A, -B, -AB) are inefficient when amplifying signals with large PAPR that is associated by high peak-to-average modulation techniques such as LTE. OFDM. Switching amplifiers (e.g., Class-D, -E, -F) are very promising due to their high efficiency when compared to their linear amplifier counterparts. Linearization techniques for switching amplifiers have been intensively investigated due to their limited sensitivity to the input amplitude of the signal. Deep-submicron CMOS technology is mostly utilized for logic circuitry, and the Moore's law scaling of CMOS optimizes transistors to operate as high-speed and low-loss switches rather than high gain transistors. Hence, it is advantageous to use transistors in switching mode as switching amplifies and use high-speed digital logic circuitry to implement linearization systems and circuitry. In this work, several linearization architectures are investigated and demonstrated. An envelope elimination and restoration (EER) transmitter that comprises a class-E power amplifier and a 10-bit digital-to-analog converter (DAC) controlled current modulator is investigated. A pipelined switched-capacitor DAC is designed to control an open-loop transconductor that operates as a current modulator, modulating the amplitude of the current supplied to a class-E PA. Such a topology allows for increased filtering of the quantization noise that is problematic in most digital PAs (DPA). The proposed quadrature and multiphase architecture can avoid the bandwidth expansion and delay mismatch associated with polar PAs. The multiphase switched capacitor power amplifier (SCPA) was proposed after the quadrature SCPA and it significantly improves the power efficiency

A wideband supply modulator for 20MHz RF bandwidth polar PAs in 65nm CMOS

A wideband modulator for a 20MHz bandwidth polar modulated PA is presented which achieves a maximum efficiency of 87.5% and a small signal -3dB bandwidth of 285MHz. Realized in 65nm CMOS, it consists of a cascoded nested Miller compensated linear amplifier and a class D switching amplifier. It can deliver 22.7dBm output power to a 5.3Ω load. With a switching frequency of 118MHz, the output switching ripple is 4.3mVrms. Keywords: supply modulator, power amplifier, CMOS and cascoded nested Miller

Wideband CMOS Data Converters for Linear and Efficient mmWave Transmitters

With continuously increasing demands for wireless connectivity, higher\ua0carrier frequencies and wider bandwidths are explored. To overcome a limited transmit power at these higher carrier frequencies, multiple\ua0input multiple output (MIMO) systems, with a large number of transmitters\ua0and antennas, are used to direct the transmitted power towards\ua0the user. With a large transmitter count, each individual transmitter\ua0needs to be small and allow for tight integration with digital circuits. In\ua0addition, modern communication standards require linear transmitters,\ua0making linearity an important factor in the transmitter design.In this thesis, radio frequency digital-to-analog converter (RF-DAC)-based transmitters are explored. They shift the transition from digital\ua0to analog closer to the antennas, performing both digital-to-analog\ua0conversion and up-conversion in a single block. To reduce the need for\ua0computationally costly digital predistortion (DPD), a linear and wellbehaved\ua0RF-DAC transfer characteristic is desirable. The combination\ua0of non-overlapping local oscillator (LO) signals and an expanding segmented\ua0non-linear RF-DAC scaling is evaluated as a way to linearize\ua0the transmitter. This linearization concept has been studied both for\ua0the linearization of the RF-DAC itself and for the joint linearization of\ua0the cascaded RF-DAC-based modulator and power amplifier (PA) combination.\ua0To adapt the linearization, observation receivers are needed.\ua0In these, high-speed analog-to-digital converters (ADCs) have a central\ua0role. A high-speed ADC has been designed and evaluated to understand\ua0how concepts used to increase the sample rate affect the dynamic performance

Study on wideband voltage controlled oscillator and high efficiency power amplifier ICs for wireless communications

制度:新 ; 報告番号:甲3604号 ; 学位の種類:博士(工学) ; 授与年月日:2012/2/20 ; 早大学位記番号:新595

Digital Radio Encoding and Power Amplifier Design for Multimode and Multiband Wireless Communications

The evolution of wireless technology has necessitated the support of multiple communication standards by mobile devices. At present, multiple chipsets/radios operating at predefined sets of modulation schemes, frequency bands, bandwidths and output power levels are used to achieve this objective. This leads to higher component counts, increased cost and limits the capacity to cope with future communication standards. In order to tackle different wireless standards using a single chipset, digital circuits have been increasingly deployed in radios and demonstrated re-configurability in different modulation schemes (multimode) and frequency bands (multiband). Despite efforts and progress made in digitizing the entire radio, the power amplifier (PA) is still designed using an conventional approach and has become the bottleneck in digital transmitters, in terms of low average power efficiency, poor compatibility with modern CMOS technology and limited re-configurability. This research addresses these issues from two aspects. The first half of the thesis investigates signal encoding issues between the modulator and PA. We propose, analyze and evaluate a new hybrid amplitude/time signal encoding scheme that significantly improves the coding efficiency and dynamic range of a digitally modulated power amplifier (DMPA) without significantly increasing design complexity. The proposed hybrid amplitude/time encoding scheme combines both the amplitude domain and the time domain to optimally encode information. Experimental results show that hybrid amplitude/time encoding results in a 35% increase in the average coding efficiency with respect to conventional time encoding, and is only 6.7% lower than peak efficiency when applied to a Wireless Local Area Network (WLAN) signal with a peak to average power ratio equal to 9.9 dB. A new DMPA architecture, based on the proposed hybrid encoding, is also proposed. The second half of this thesis presents the design, analysis and implementation of a CMOS PA that is amenable to the proposed hybrid encoding scheme. A multi-way current mode class-D PA architecture has been proposed and realized in 130 nm CMOS technology. The designed PA has satisfied the objectives of wide bandwidth (1.5 GHz - 2.7 GHz at 1 dB output power), and high efficiency (PAE 63%) in addition to demonstrating linear responses using the proposed digital encoding. A complete digital transmitter combining the encoder and the multi-way PA was also investigated. The overall efficiency is 27% modulating 7.3 dB peak to average power ratio QAM signals

‘Bang-Bang’ technique in supply modulation for linear wideband RF power amplifiers

This paper deals with the design techniques of power efficient switching regulators intended for linear power amplifiers employing envelope tracking techniques in wideband wireless standards. The bottlenecks involve a tradeoff between ripple voltage, slew rate and bandwidth. The slew rate limitation is identified as the main challenge, then a ‘bang-bang’ slew enhancement technique is proposed. This approach enables the use of efficient supply modulators in wideband power amplifiers. The proposed scheme does not significantly degrade PA efficiency and preserves the stability of the switching regulator. The prototype has been implemented using the TSMC 0.18 µm technology; schematic simulation results in Cadence® are presented to prove the concept.Postprint (published version