차량용 CIS Interface 를 위한 All-Digital Phase-Locked Loop 의 설계 및 분석

학위논문 (석사) -- 서울대학교 대학원 : 공과대학 전기·정보공학부, 2021. 2. 정덕균.This thesis presents design techniques for All-Digital Phase-Locked Loop (ADPLL) assisting the automotive CMOS image sensor (CIS) interface. To target Gear 3 of the automotive physical system, the proposed AD-PLL has a wide operation range, low RMS jitter, and high PVT tolerance characteristics. Detailed analysis of the loop dynamics and the noise analysis of AD-PLL are done by using Matlab and Verilog behavioral modeling simulation before an actual design. Based on that analysis, the optimal DLF gain configurations are yielded, and also, accurate output responses and performance are predictable. The design techniques to reduce the output RMS jitter are discussed thoroughly and utilized for actual implementation. The proposed AD-PLL is fabricated in the 40 nm CMOS process and occupies an effective area of 0.026 mm2. The PLL output clock pulses exhibit an RMS jitter of 827 fs at 2 GHz. The power dissipation is 5.8 mW at 2 GHz, where the overall supply voltage domain is 0.9 V excluding the buffer which is 1.1 V domain.본 논문에서는 자동차 CMOS 이미지 센서 (CIS) 인터페이스를 지원하 는 AD-PLL 을 제안한다. Automotive Physical 시스템의 Gear 3 를 지원하기 위해 제안된 AD-PLL 은 1.5 GHz 에서 3 GHz 의 동작 주파수를 가지며, 낮 은 RMS Jitter 및 PVT 변화에 대한 높은 둔감성을 갖는다. 설계에 앞서서 Matlab 및 Verilog Behavioral Simulation 을 통해 Loop system 의 역학에 대한 자세한 분석 및 AD-PLL 의 Noise 분석을 수행하였고, 이 분석을 기반으로 최적의 DLF gain 과 정확한 출력 응답 및 성능을 예측 할 수 있었다. 또한, 출력의 Phase Noise 와 RMS Jitter 를 줄이기 위한 설계 기법을 자세히 다루고 있으며 이를 실제 구현에 활용했다. 제안된 회로는 40 nm CMOS 공정으로 제작되었으며 Decoupling Cap 을 제외하고 0.026 mm2 의 유효 면적을 차지한다. 측정된 출력 Clock 신호의 RMS Jitter 값은 2 GHz 에서 827 fs 이며, 총 5.8 mW의 Power 를 소비한다. 이 때, 전체적인 공급 전압은 0.9 V 이며, Buffer 의 Power 만이 1.1 V 를 사용하 였다.ABSTRACT I CONTENTS II LIST OF FIGURES IV LIST OF TABLES VII CHAPTER 1 INTRODUCTION 1 1.1 MOTIVATION 1 1.2 THESIS ORGANIZATION 3 CHAPTER 2 BACKGROUND ON ALL-DIGITAL PLL 4 2.1 OVERVIEW 4 2.2 BUILDING BLOCKS OF AD-PLL 7 2.2.1 TIME-TO-DIGITAL CONVERTER 7 2.2.2 DIGITALLY-CONTROLLED OSCILLATOR 10 2.2.3 DIGITAL LOOP FILTER 13 2.2.4 DELTA-SIGMA MODULATOR 16 2.3 PHASE NOISE ANALYSIS OF AD-PLL 20 2.3.1 BASIC ASSUMPTION OF LINEAR ANALYSIS 20 2.3.2 NOISE SOURCES OF AD-PLL 21 2.3.3 EFFECTS OF LOOP DELAY ON AD-PLL 24 2.3.4 PHASE NOISE ANALYSIS OF PROPOSED AD-PLL 26 CHAPTER 3 DESIGN OF ALL-DIGITAL PLL 28 3.1 DESIGN CONSIDERATION 28 3.2 OVERALL ARCHITECTURE 30 3.3 CIRCUIT IMPLEMENTATION 32 3.3.1 PFD-TDC 32 3.3.2 DCO 37 3.3.3 DIGITAL BLOCK 43 3.3.4 LEVEL SHIFTING BUFFER AND DIVIDER 45 CHAPTER 4 MEASUREMENT AND SIMULATION RESULTS 52 4.1 DIE PHOTOMICROGRAPH 52 4.2 MEASUREMENT SETUP 54 4.3 TRANSIENT ANALYSIS 57 4.4 PHASE NOISE AND SPUR PERFORMANCE 59 4.4.1 FREE-RUNNING DCO 59 4.4.2 PLL PERFORMANCE 61 4.5 PERFORMANCE SUMMARY 65 CHAPTER 5 CONCLUSION 67 BIBLIOGRAPHY 68 초 록 72Maste

Switched Capacitor Loop Filter 와 Source Switched Charge Pump 를 이용한 Phase-Locked Loop 의 설계

학위논문(석사) -- 서울대학교대학원 : 공과대학 전기·정보공학부, 2022.2. 정덕균.This thesis proposes a low integrated RMS jitter and low reference spur phase locked loop (PLL) using a switched capacitor loop filter and source switched charge pump. The PLL employs a single tunable charge pump which reduces current mis match across wide control voltage range and charge sharing effect to get high perfor mance of reference spur level. The switched capacitor loop filter is adopted to achieve insensitivity to temperature, supply voltage, and process variation of a resistor. The proposed PLL covers a wide frequency range and has a low integrated RMS jitter and low reference spur level to target various interface standards. The mechanism of switched capacitor loop filter and source switched charge pump is analyzed. Fabricated in 40 nm CMOS technology, the proposed analog PLL provides four phase for a quarter-rate transmitter, consumes 6.35 mW at 12 GHz using 750 MHz reference clock, and occupies an 0.008 mm2 with an integrated RMS jitter (10 kHz to 100 MHz) of 244.8 fs. As a result, the PLL achieves a figure of merit (FoM) of -244.2 dB with high power efficiency of 0.53 mW/GHz, and reference spur level is -60.3 dBc.본 논문에서는 낮은 RMS jitter 와 낮은 레퍼런스 스퍼를 가지며 스위치축전기 루프 필터와 소스 스위치 전하 펌프를 이용한 PLL 을 제안한다. 제안된 PLL 은 레퍼런스 스퍼의 성능을 위해 넓은 컨트롤 전압의 범위 동안 전류의 오차를 줄여주고 전하 공유 효과를 줄여주는 하나의 조절 가능한 전하 펌프를 사용하였다. 저항의 온도, 공급 전압, 공정 변화에 따른 민감도를 낮추기 위해 스위치 축전기 루프 필터가 사용되었다. 다양한 인터페이스 표준을 지원하기 위해 제안하는 PLL 은 넓은 주파수 범위를 지원하고 낮은 RMS jitter 와 낮은 레퍼런스 스퍼를 갖는다. 스위치 축전기 루프 필터와 소스 스위치 전하 펌프의 동작 원리에 대해 분석하였다. 40 nm CMOS 공정으로 제작되었으며, 제안된 회로는 quarter-rate 송신기를 위해 4 개의 phase 를 만들어내며 750 MHz 의 레퍼런스 클락을 이용하여 12 GHz 에서 6.35 mW 의 power 를 소모하고 0.008mm2 의 유효 면적을 차지하고 10 kHz 부터 100 MHz 까지 적분했을 때의 RMS jitter 값은 244.8fs 이다. 제안하는 PLL 은 -244.2 dB 의 FoM, 0.53 mW/GHz 의 power 효율을 달성했으며 레퍼런스 스퍼는 -60.3 dBc 이다CHAPTER 1 INTRODUCTION 1 1.1 MOTIVATION 1 1.2 THESIS ORGANIZATION 3 CHAPTER 2 BACKGROUNDS 4 2.1 CLOCK GENERATION IN SERIAL LINK 4 2.2 PLL BUILDING BLOCKS 6 2.2.1 OVERVIEW 6 2.2.2 PHASE FREQUENCY DETECTOR 7 2.2.3 CHARGE PUMP AND LOOP FILTER 9 2.2.4 VOLTAGE CONTROLLED OSCILLATOR 10 2.2.5 FREQUENCY DIVIDER 13 2.3 PLL LOOP ANALYSIS 15 CHAPTER 3 PLL WITH SWITCHED CAPACITOR LOOP FILTER AND SOURCE SWITCHED CHARGE PUMP 19 3.1 DESIGN CONSIDERATION 19 3.2 PROPOSED ARCHITECTURE 21 3.3 CIRCUIT IMPLEMENTATION 23 3.3.1 PHASE FREQUENCY DETECTOR 23 3.3.2 SOURCE SWITCHED CHARGE PUMP 26 3.3.3 SWITCHED CAPACITOR LOOP FILTER 30 3.3.4 VOLTAGE CONTROLLED OSCILLATOR 35 3.3.5 POST VCO AMPLIFIER 39 3.3.6 FREQUENCY DIVIDER 40 CHAPTER 4 MEASUREMENT RESULTS 43 4.1 CHIP PHOTOMICROGRAPH 43 4.2 MEASUREMENT SETUP 45 4.3 MEASURED PHASE NOISE AND REFERENCE SPUR 47 4.4 PERFORMANCE SUMMARY 50 CHAPTER 5 CONCLUSION 52 BIBLIOGRAPHY 53 초 록 58석

A Low-Power BFSK/OOK Transmitter for Wireless Sensors

In recent years, significant improvements in semiconductor technology have allowed consistent development of wireless chipsets in terms of functionality and form factor. This has opened up a broad range of applications for implantable wireless sensors and telemetry devices in multiple categories, such as military, industrial, and medical uses. The nature of these applications often requires the wireless sensors to be low-weight and energy-efficient to achieve long battery life. Among the various functions of these sensors, the communication block, used to transmit the gathered data, is typically the most power-hungry block. In typical wireless sensor networks, transmission range is below 10 meters and required radiated power is below 1 milliwatt. In such cases, power consumption of the frequency-synthesis circuits prior to the power amplifier of the transmitter becomes significant. Reducing this power consumption is currently the focus of various research endeavors. A popular method of achieving this goal is using a direct-modulation transmitter where the generated carrier is directly modulated with baseband data using simple modulation schemes. Among the different variations of direct-modulation transmitters, transmitters using unlocked digitally-controlled oscillators and transmitters with injection or resonator-locked oscillators are widely investigated because of their simple structure. These transmitters can achieve low-power and stable operation either with the help of recalibration or by sacrificing tuning capability. In contrast, phase-locked-loop-based (PLL) transmitters are less researched. The PLL uses a feedback loop to lock the carrier to a reference frequency with a programmable ratio and thus achieves good frequency stability and convenient tunability. This work focuses on PLL-based transmitters. The initial goal of this work is to reduce the power consumption of the oscillator and frequency divider, the two most power-consuming blocks in a PLL. Novel topologies for these two blocks are proposed which achieve ultra-low-power operation. Along with measured performance, mathematical analysis to derive rule-of-thumb design approaches are presented. Finally, the full transmitter is implemented using these blocks in a 130 nanometer CMOS process and is successfully tested for low-power operation

FULLY INTEGRATED HIGH-FREQUENCY CLOCK GENERATION AND SYNCHRONIZATION TECHINIQUES

Department of Electrical EngineeringThis thesis presents clock generation and synchronization techniques for RF wireless communication. First, it deals with voltage-controlled oscillators (VCOs) for local oscillators (LO) in transceivers, and secondly delay-locked loops for synchronization. For the high-performance LO, VCO is one of the key blocks. LC VCOs and ring VCOs are commonly-used types. Their characteristics are varied for different frequency bands. In this thesis, two types of VCOs, LC VCO and ring VCO, are presented with specific applications. For the multi-clock generator which could be used for carrier aggregation or frequency hopping, ring-type digitally controlled oscillator (DCO) was designed covering 900-1200 MHz with -165 dB FOM. For the multi-band frequency synthesizer which could be used for 5G communication with backward compatibility, three LC VCOs are designed which frequency range of 25-30 GHz for 5G, 5.2-6.0 GHz for LTE, 2.7-4.2 GHz for 2G-3G communication, respectively. For the clock synchronization in RF communications, a delay-locked loop (DLL) using a digital-to-analog converter (DAC) based band-selecting circuit (BSC) was presented to achieve a wide harmonic-locking-free frequency range. The BSC used the proposed exponential digital-to-analog converter (EDAC) to generate a collection of initial control voltages which follow a sequence of geometric with satisfying the condition for preventing harmonic locking problem. Therefore, the BSC can cover a much wider frequency range which is free from harmonic locking problem compared to initial band selection techniques using conventional, linear DAC (LDAC) that have a set of control voltages of arithmetic sequence. In this thesis, the DLL was implemented in a 65-nm CMOS process, and it had a measured frequency range from 100 to 1500 MHz which range is free from harmonic locking. The measure rms jitter and 1-MHz phase noise at 1000 MHz were 1.99 ps and ?28 dBc/Hz, respectively. The DLL consumes 5.5 mW and its active area was 0.052 mm2.clos

Process and Temperature Compensated Wideband Injection Locked Frequency Dividers and their Application to Low-Power 2.4-GHz Frequency Synthesizers

There has been a dramatic increase in wireless awareness among the user community in the past five years. The 2.4-GHz Industrial, Scientific and Medical (ISM) band is being used for a diverse range of applications due to the following reasons. It is the only unlicensed band approved worldwide and it offers more bandwidth and supports higher data rates compared to the 915-MHz ISM band. The power consumption of devices utilizing the 2.4-GHz band is much lower compared to the 5.2-GHz ISM band. Protocols like Bluetooth and Zigbee that utilize the 2.4-GHz ISM band are becoming extremely popular. Bluetooth is an economic wireless solution for short range connectivity between PC, cell phones, PDAs, Laptops etc. The Zigbee protocol is a wireless technology that was developed as an open global standard to address the unique needs of low-cost, lowpower, wireless sensor networks. Wireless sensor networks are becoming ubiquitous, especially after the recent terrorist activities. Sensors are employed in strategic locations for real-time environmental monitoring, where they collect and transmit data frequently to a nearby terminal. The devices operating in this band are usually compact and battery powered. To enhance battery life and avoid the cumbersome task of battery replacement, the devices used should consume extremely low power. Also, to meet the growing demands cost and sized has to be kept low which mandates fully monolithic implementation using low cost process. CMOS process is extremely attractive for such applications because of its low cost and the possibility to integrate baseband and high frequency circuits on the same chip. A fully integrated solution is attractive for low power consumption as it avoids the need for power hungry drivers for driving off-chip components. The transceiver is often the most power hungry block in a wireless communication system. The frequency divider (prescaler) and the voltage controlled oscillator in the transmitter’s frequency synthesizer are among the major sources of power consumption. There have been a number of publications in the past few decades on low-power high-performance VCOs. Therefore this work focuses on prescalers. A class of analog frequency dividers called as Injection-Locked Frequency Dividers (ILFD) was introduced in the recent past as low power frequency division. ILFDs can consume an order of magnitude lower power when compared to conventional flip-flop based dividers. However the range of operation frequency also knows as the locking range is limited. ILFDs can be classified as LC based and Ring based. Though LC based are insensitive to process and temperature variation, they cannot be used for the 2.4-GHz ISM band because of the large size of on-chip inductors at these frequencies. This causes a lot of valuable chip area to be wasted. Ring based ILFDs are compact and provide a low power solution but are extremely sensitive to process and temperature variations. Process and temperature variation can cause ring based ILFD to loose lock in the desired operating band. The goal of this work is to make the ring based ILFDs useful for practical applications. Techniques to extend the locking range of the ILFDs are discussed. A novel and simple compensation technique is devised to compensate the ILFD and keep the locking range tight with process and temperature variations. The proposed ILFD is used in a 2.4-GHz frequency synthesizer that is optimized for fractional-N synthesis. Measurement results supporting the theory are provided

CMOS Signal Synthesizers for Emerging RF-to-Optical Applications

The need for clean and powerful signal generation is ubiquitous, with applications spanning the spectrum from RF to mm-Wave, to into and beyond the terahertz-gap. RF applications including mobile telephony and microprocessors have effectively harnessed mixed-signal integration in CMOS to realize robust on-chip signal sources calibrated against adverse ambient conditions. Combined with low cost and high yield, the CMOS component of hand-held devices costs a few cents per part per million parts. This low cost, and integrated digital processing, make CMOS an attractive option for applications like high-resolution imaging and ranging, and the emerging 5-G communication space. RADAR techniques when expanded to optical frequencies can enable micrometers of resolution for 3D imaging. These applications, however, impose upto 100x more exacting specifications on power and spectral purity at much higher frequencies than conventional RF synthesizers. This generation of applications will present unconventional challenges for transistor technologies - whether it is to squeeze performance in the conventionally used spectrum, already wrung dry, or signal generation and system design in the relatively emptier mm-Wave to sub-mmWave spectrum, much of the latter falling in the ``Terahertz Gap". Indeed, transistor scaling and innovative device physics leading to new transistor topologies have yielded higher cut-off frequencies in CMOS, though still lagging well behind SiGe and III-V semiconductors. To avoid multimodule solutions with functionality partitioned across different technologies, CMOS must be pushed out of its comfort zone, and technology scaling has to have accompanying breakthroughs in design approaches not only at the system but also at the block level. In this thesis, while not targeting a specific application, we seek to formulate the obstacles in synthesizing high frequency, high power and low noise signals in CMOS and construct a coherent design methodology to address them. Based on this, three novel prototypes to overcome the limiting factors in each case are presented. The first half of this thesis deals with high frequency signal synthesis and power generation in CMOS. Outside the range of frequencies where the transistor has gain, frequency generation necessitates harmonic extraction either as harmonic oscillators or as frequency multipliers. We augment the traditional maximum oscillation frequency metric (fmax), which only accounts for transistor losses, with passive component loss to derive an effective fmax metric. We then present a methodology for building oscillators at this fmax, the Maximum Gain Ring Oscillator. Next, we explore generating large signals beyond fmax through harmonic extraction in multipliers. Applying concepts of waveform shaping, we demonstrate a Power Mixer that engineers transistor nonlinearity by manipulating the amplitudes and relative phase shifts of different device nodes to maximize performance at a specific harmonic beyond device cut-off. The second half proposes a new architecture for an ultra-low noise phase-locked loop (PLL), the Reference-Sampling PLL. In conventional PLLs, a noisy buffer converts the slow, low-noise sine-wave reference signal to a jittery square-wave clock against which the phase of a noisy voltage-controlled oscillator (VCO) is corrected. We eliminate this reference buffer, and measure phase error by sampling the reference sine-wave with the 50x faster VCO waveform already available on chip, and selecting the relevant sample with voltage proportional to phase error. By avoiding the N-squared multiplication of the high-power reference buffer noise, and directly using voltage-mode phase error to control the VCO, we eliminate several noisy components in the controlling loop for ultra-low integrated jitter for a given power consumption. Further, isolation of the VCO tank from any varying load, unlike other contemporary divider-less PLL architectures, results in an architecture with record performance in the low-noise and low-spur space. We conclude with work that brings together concepts developed for clean, high-power signal generation towards a hybrid CMOS-Optical approach to Frequency-Modulated Continuous-Wave (FMCW) Light-Detection-And-Ranging (LIDAR). Cost-effective tunable lasers are temperature-sensitive and have nonlinear tuning profiles, rendering precise frequency modulations or 'chirps' untenable. Locking them to an electronic reference through an electro-optic PLL, and electronically calibrating the control signal for nonlinearity and ambient sensitivity, can make such chirps possible. Approaches that build on the body of advances in electrical PLLs to control the performance, and ease the specification on the design of optical systems are proposed. Eventually, we seek to leverage the twin advantages of silicon-intensive integration and low-cost high-yield towards developing a single-chip solution that uses on-chip signal processing and phased arrays to generate precise and robust chirps for an electronically-steerable fine LIDAR beam

A 90 nm CMOS 16 Gb/s Transceiver for Optical Interconnects

Interconnect architectures which leverage high-bandwidth optical channels offer a promising solution to address the increasing chip-to-chip I/O bandwidth demands. This paper describes a dense, high-speed, and low-power CMOS optical interconnect transceiver architecture. Vertical-cavity surface-emitting laser (VCSEL) data rate is extended for a given average current and corresponding reliability level with a four-tap current summing FIR transmitter. A low-voltage integrating and double-sampling optical receiver front-end provides adequate sensitivity in a power efficient manner by avoiding linear high-gain elements common in conventional transimpedance-amplifier (TIA) receivers. Clock recovery is performed with a dual-loop architecture which employs baud-rate phase detection and feedback interpolation to achieve reduced power consumption, while high-precision phase spacing is ensured at both the transmitter and receiver through adjustable delay clock buffers. A prototype chip fabricated in 1 V 90 nm CMOS achieves 16 Gb/s operation while consuming 129 mW and occupying 0.105 mm^2

LOW-JITTER AND LOW-SPUR RING-OSCILLATOR-BASED PHASE-LOCKED LOOPS

Department of Electrical EngineeringIn recent years, ring-oscillator based clock generators have drawn a lot of attention due to the merits of high area efficiency, potentially wide tuning range, and multi-phase generation. However, the key challenge is how to suppress the poor jitter of ring oscillators. There have been many efforts to develop a ring-oscillator-based clock generator targeting very low-jitter performance. However, it remains difficult for conventional architectures to achieve both low RMS jitter and low levels of reference spurs concurrently while having a high multiplication factor. In this dissertation, a time-domain analysis is presented that provides an intuitive understanding of RMS jitter calculation of the clock generators from their phase-error correction mechanisms. Based on this analysis, we propose new designs of a ring-oscillator-based PLL that addresses the challenges of prior-art ring-based architectures. This dissertation introduces a ring-oscillator-based PLL with the proposed fast phase-error correction (FPEC) technique, which emulates the phase-realignment mechanism of an injection-locked clock multiplier (ILCM). With the FPEC technique, the phase error of the voltage-controlled oscillator (VCO) is quickly removed, achieving ultra-low jitter. In addition, in the transfer function of the proposed architecture, an intrinsic integrator is involved since it is naturally based on a PLL topology. The proposed PLL can thus have low levels of reference spurs while maintaining high stability even for a large multiplication factor. Furthermore, it presents another design of a digital PLL embodying the FPEC technique (or FPEC DPLL). To overcome the problem of a conventional TDC, a low-power optimally-spaced (OS) TDC capable of effectively minimizing the quantization error is presented. In the proposed FPEC DPLL, background digital controllers continuously calibrate the decision thresholds and the gain of the error correction by the loop to be optimal, thus dramatically reducing the quantization error. Since the proposed architecture is implemented in a digital fashion, the variables defining the characteristics of the loop can be easily estimated and calibrated by digital calibrators. As a result, the performances of an ultra-low jitter and the figure-of-merit can be achieved.clos

Design and Analysis of a Wide Loop-Bandwidth RF Synthesizer Using Ring oscillator For DECT Receiver

Wireless communication devices including cordless phones and modern digital cellular systems (DCSs) use portable transceiver systems. The frequency synthesis of this type of transceiver system is done using a phase-locked loop oscillator. Traditional on-chip implementation of a complete phase-locked loop using a ring type voltage controlled oscillator contributes higher noise at the output. An alternative architecture, phase-locked loop (PLL) with wide loop-bandwidth, is proposed in this research to suppress the noise from the traditional ring oscillator. The proposed PLL is amendable to on-chip integration as well as commercially suitable for a Digital Enhancement Cordless Telephone (DECT) system which needs flexible noise margin. In this research, a 1.5552 GHz PLL-based frequency synthesizer is designed with a noisy ring oscillator. The wide loop-bandwidth approach is applied in designing the PLL to suppress the VCO noise. In this type of frequency synthesizer, the frequency divider is operated at higher frequencies with less noise and care is taken to design the delay flip-flops and logic gates that can be operated at higher frequencies. Current-mode control can be employed in designing the logic gates and the delay flip-flop to enhance the speed performance of the divider. An alternate approach in designing a high-speed divider using a current-mode control approach is also presented

Design of CMOS integrated frequency synthesizers for ultra-wideband wireless communications systems

Ultra¬wide band (UWB) system is a breakthrough in wireless communication, as it provides data rate one order higher than existing ones. This dissertation focuses on the design of CMOS integrated frequency synthesizer and its building blocks used in UWB system. A mixer¬based frequency synthesizer architecture is proposed to satisfy the agile frequency hopping requirement, which is no more than 9.5 ns, three orders faster than conventional phase¬locked loop (PLL)¬based synthesizers. Harmonic cancela¬tion technique is extended and applied to suppress the undesired harmonic mixing components. Simulation shows that sidebands at 2.4 GHz and 5 GHz are below 36 dBc from carrier. The frequency synthesizer contains a novel quadrature VCO based on the capacitive source degeneration structure. The QVCO tackles the jeopardous ambiguity of the oscillation frequency in conventional QVCOs. Measurement shows that the 5¬GHz CSD¬QVCO in 0.18 µm CMOS technology draws 5.2 mA current from a 1.2 V power supply. Its phase noise is ¬120 dBc at 3 MHz offset. Compared with existing phase shift LC QVCOs, the proposed CSD¬QVCO presents better phase noise and power efficiency. Finally, a novel injection locking frequency divider (ILFD) is presented. Im¬plemented with three stages in 0.18 µm CMOS technology, the ILFD draws 3¬mA current from a 1.8¬V power supply. It achieves multiple large division ratios as 6, 12, and 18 with all locking ranges greater than 1.7 GHz and injection frequency up to 11 GHz. Compared with other published ILFDs, the proposed ILFD achieves the largest division ratio with satisfactory locking range