Architecture of a cognitive non-line-of-sight backhaul for 5G outdoor urban small cells

Densely deployed small cell networks will address the growing demand for broadband mobile connectivity, by increasing access network capacity and coverage. However, most potential small cell base station (SCBS) locations do not have existing telecommunication infrastructure. Providing backhaul connectivity to core networks is therefore a challenge. Millimeter wave (mmW) technologies operated at 30-90GHz are currently being considered to provide low-cost, flexible, high-capacity and reliable backhaul solutions using existing roof-mounted backhaul aggregation sites. Using intelligent mmW radio devices and massive multiple-input multiple-output (MIMO), for enabling point-to-multipoint (PtMP) operation, is considered in this research. The core aim of this research is to develop an architecture of an intelligent non-line-sight (NLOS) small cell backhaul (SCB) system based on mmW and massive MIMO technologies, and supporting intelligent algorithms to facilitate reliable NLOS street-to-rooftop NLOS SCB connectivity. In the proposed architecture, diffraction points are used as signal anchor points between backhaul radio devices. In the new architecture the integration of these technologies is considered. This involves the design of efficient artificial intelligence algorithms to enable backhaul radio devices to autonomously select suitable NLOS propagation paths, find an optimal number of links that meet the backhaul performance requirements and determine an optimal number of diffractions points capable of covering predetermined SCB locations. Throughout the thesis, a number of algorithms are developed and simulated using the MATLAB application. This thesis mainly investigates three key issues: First, a novel intelligent NLOS SCB architecture, termed the cognitive NLOS SCB (CNSCB) system is proposed to enable street-to-rooftop NLOS connectivity using predetermined diffraction points located on roof edges. Second, an algorithm to enable the autonomous creation of multiple-paths, evaluate the performance of each link and determine an optimal number of possible paths per backhaul link is developed. Third, an algorithm to determine the optimal number of diffraction points that can cover an identified SCBS location is also developed. Also, another investigated issue related to the operation of the proposed architecture is its energy efficiency, and its performance is compared to that of a point-to-point (PtP) architecture. The proposed solutions were examined using analytical models, simulations and experimental work to determine the strength of the street-to-rooftop backhaul links and their ability to meet current and future SCB requirements. The results obtained showed that reliable multiple NLOS links can be achieved using device intelligence to guide radio signals along the propagation path. Furthermore, the PtMP architecture is found to be more energy efficient than the PtP architecture. The proposed architecture and algorithms offer a novel backhaul solution for outdoor urban small cells. Finally, this research shows that traditional techniques of addressing the demand for connectivity, which consisted of improving or evolving existing solutions, may nolonger be applicable in emerging communication technologies. There is therefore need to consider new ways of solving the emerging challenges

Physical-Layer Security with Full-Duplex Transceivers and Multiuser Receiver at Eve

Full-duplex communication enables simultaneous transmission from both ends of a communication link, thereby promising significant performance gains. Generally, it has been shown that the throughput and delay gains of full-duplex communication are somewhat limited in realistic network settings, leading researchers to study other possible applications that can accord higher gains. The potential of full-duplex communication in improving the physical-layer security of a communication link is investigated in this contribution. We specifically present a thorough analysis of the achievable ergodic secrecy rate and the secrecy degrees of freedom with full-duplex communication in the presence of a half-duplex eavesdropper node, with both single-user decoding and multi-user decoding capabilities. For the latter case, an eavesdropper with successive interference cancellation and joint decoding capabilities is assumed. Irrespective of the eavesdropper capabilities and channel strengths, the ergodic secrecy rate with full-duplex communication is found to grow linearly with the log of the direct channel signal-to-noise-ratio (SNR) as opposed to the flattened out secrecy rate with conventional half-duplex communication. Consequently, the secrecy degrees of freedom with full-duplex is shown to be two as opposed to that of zero in half-duplex mode

A High-Gain Transmitarray for Generating Dual-Mode OAM Beams

This paper proposes a novel transmitarray antenna which can achieve high gain and produce dual-mode orbital angular momentum (OAM) beams in Ku band. Two back-to-back wideband dual-polarized microstrip antennas are employed as the unit cells, which are connected using metalized via holes. Full 360 o phase ranges can be obtained by varying the length of feeding lines in two orthogonal polarizations. Due to high isolation between the two orthogonal polarizations, dual-mode OAM beams can be formed simultaneously by tuning phase distributions in x- and y-polarizations, respectively. The approach for generating OAM beams is explained. To verify this concept, one prototype carrying 0 and +1 mode OAM beams is designed, fabricated and measured. Experimental results demonstrate that the both 0 and +1 mode OAM beams can be generated successfully, and the measured results agree well with the simulated results. Because of high directivity and focusing effects of transmitarray, the proposed +1 mode OAM beam has stable performance at a long propagation distance. The maximum gain reaches 26 dBi and 20 dBi in 0 and +1 mode OAM beams, respectively. Meanwhile, a narrow divergence angle of +/-5 o is obtained in +1 mode OAM beam. Compared to other OAM antennas reported, main advantages of the proposed antenna include high gain, narrow divergence angle?low cost, planar structure and the capability of producing dual-mode OAM beams

5G innovation opportunities-- A discussion paper

On the shaping of 5G technologies and networks, scope for wider service and applications innovation and UK strengths and opportunities

Beam scanning by liquid-crystal biasing in a modified SIW structure

A fixed-frequency beam-scanning 1D antenna based on Liquid Crystals (LCs) is designed for application in 2D scanning with lateral alignment. The 2D array environment imposes full decoupling of adjacent 1D antennas, which often conflicts with the LC requirement of DC biasing: the proposed design accommodates both. The LC medium is placed inside a Substrate Integrated Waveguide (SIW) modified to work as a Groove Gap Waveguide, with radiating slots etched on the upper broad wall, that radiates as a Leaky-Wave Antenna (LWA). This allows effective application of the DC bias voltage needed for tuning the LCs. At the same time, the RF field remains laterally confined, enabling the possibility to lay several antennas in parallel and achieve 2D beam scanning. The design is validated by simulation employing the actual properties of a commercial LC medium

1-D broadside-radiating leaky-wave antenna based on a numerically synthesized impedance surface

A newly-developed deterministic numerical technique for the automated design of metasurface antennas is applied here for the first time to the design of a 1-D printed Leaky-Wave Antenna (LWA) for broadside radiation. The surface impedance synthesis process does not require any a priori knowledge on the impedance pattern, and starts from a mask constraint on the desired far-field and practical bounds on the unit cell impedance values. The designed reactance surface for broadside radiation exhibits a non conventional patterning; this highlights the merit of using an automated design process for a design well known to be challenging for analytical methods. The antenna is physically implemented with an array of metal strips with varying gap widths and simulation results show very good agreement with the predicted performance