Self-calibrating random access logarithmic pixel for on chip camera

CMOS active pixel sensors (APS) have shown competitive performance with charge-coupled device (CCD) and offer many advantages in cost, system power reduction and on-chip integration of VLSI electronics. Among CMOS image sensors, sensors with logarithmic pixels are particularly applicable for outdoor environment where the light intensity varies over a wide range. They are also randomly accessible in both time and space. A major drawback comes from process variations during fabrication. This gives rise to a considerable fixed pattern noise (FPN) which deteriorates the image quality. In this thesis, a technique that greatly reduces FPN using on-chip calibration is introduced. An image sensor that consists of 64x64 active pixels has been designed, fabricated and tested. Pixel pitch is 18um x 19.2um? and is fabricated in a 0.5-um? CMOS process. The proposed pixel circuit considerably reduces the FPN as predicted in theoretical analysis. The measured FPN value is 2.29% of output voltage swing and column-wise FPN is 1.49% of mean output voltage over each column

Ultra-low power mixed-signal frontend for wearable EEGs

Electronics circuits are ubiquitous in daily life, aided by advancements in the chip design industry, leading to miniaturised solutions for typical day to day problems. One of the critical healthcare areas helped by this advancement in technology is electroencephalography (EEG). EEG is a non-invasive method of tracking a person's brain waves, and a crucial tool in several healthcare contexts, including epilepsy and sleep disorders. Current ambulatory EEG systems still suffer from limitations that affect their usability. Furthermore, many patients admitted to emergency departments (ED) for a neurological disorder like altered mental status or seizures, would remain undiagnosed hours to days after admission, which leads to an elevated rate of death compared to other conditions. Conducting a thorough EEG monitoring in early-stage could prevent further damage to the brain and avoid high mortality. But lack of portability and ease of access results in a long wait time for the prescribed patients. All real signals are analogue in nature, including brainwaves sensed by EEG systems. For converting the EEG signal into digital for further processing, a truly wearable EEG has to have an analogue mixed-signal front-end (AFE). This research aims to define the specifications for building a custom AFE for the EEG recording and use that to review the suitability of the architectures available in the literature. Another critical task is to provide new architectures that can meet the developed specifications for EEG monitoring and can be used in epilepsy diagnosis, sleep monitoring, drowsiness detection and depression study. The thesis starts with a preview on EEG technology and available methods of brainwaves recording. It further expands to design requirements for the AFE, with a discussion about critical issues that need resolving. Three new continuous-time capacitive feedback chopped amplifier designs are proposed. A novel calibration loop for setting the accurate value for a pseudo-resistor, which is a crucial block in the proposed topology, is also discussed. This pseudoresistor calibration loop achieved the resistor variation of under 8.25%. The thesis also presents a new design of a curvature corrected bandgap, as well as a novel DDA based fourth-order Sallen-Key filter. A modified sensor frontend architecture is then proposed, along with a detailed analysis of its implementation. Measurement results of the AFE are finally presented. The AFE consumed a total power of 3.2A (including ADC, amplifier, filter, and current generation circuitry) with the overall integrated input-referred noise of 0.87V-rms in the frequency band of 0.5-50Hz. Measurement results confirmed that only the proposed AFE achieved all defined specifications for the wearable EEG system with the smallest power consumption than state-of-art architectures that meet few but not all specifications. The AFE also achieved a CMRR of 131.62dB, which is higher than any studied architectures.Open Acces

Front-end receiver for miniaturised ultrasound imaging

Point of care ultrasonography has been the focus of extensive research over the past few decades. Miniaturised, wireless systems have been envisaged for new application areas, such as capsule endoscopy, implantable ultrasound and wearable ultrasound. The hardware constraints of such small-scale systems are severe, and tradeoffs between power consumption, size, data bandwidth and cost must be carefully balanced. To address these challenges, two synthetic aperture receiver architectures are proposed and compared. The architectures target highly miniaturised, low cost, B-mode ultrasound imaging systems. The first architecture utilises quadrature (I/Q) sampling to minimise the signal bandwidth and computational load. Synthetic aperture beamforming is carried out using a single-channel, pipelined protocol in order to minimise system complexity and power consumption. A digital beamformer dynamically apodises and focuses the data by interpolating and applying complex phase rotations to the I/Q samples. The beamformer is implemented on a Spartan-6 FPGA and consumes 296mW for a frame rate of 7Hz. The second architecture employs compressive sensing within the finite rate of innovation (FRI) framework to further reduce the data bandwidth. Signals are sampled below the Nyquist frequency, and then transmitted to a digital back-end processor, which reconstructs I/Q components non-linearly, and then carries out synthetic aperture beamforming. Both architectures were tested in hardware using a single-channel analogue front-end (AFE) that was designed and fabricated in AMS 0.35μm CMOS. The AFE demodulates RF ultrasound signals sequentially into I/Q components, and comprises a low-noise preamplifier, mixer, programmable gain amplifier (PGA) and lowpass filter. A variable gain low noise preamplifier topology is used to enable quasi-exponential time-gain control (TGC). The PGA enables digital selection of three gain values (15dB, 22dB and 25.5dB). The bandwidth of the lowpass filter is also selectable between 1.85MHz, 510kHz and 195kHz to allow for testing of both architectural frameworks. The entire AFE consumes 7.8 mW and occupies an area of 1.5×1.5 mm. In addition to the AFE, this thesis also presents the design of a pseudodifferential, log-domain multiplier-filter or “multer” which demodulates low-RF signals in the current-domain. This circuit targets high impedance transducers such as capacitive micromachined ultrasound transducers (CMUTs) and offers a 20dB improvement in dynamic range over the voltage-mode AFE. The bandwidth is also electronically tunable. The circuit was implemented in 0.35μm BiCMOS and was simulated in Cadence; however, no fabrication results were obtained for this circuit. B-mode images were obtained for both architectures. The quadrature SAB method yields a higher image SNR and 9% lower root mean squared error with respect to the RF-beamformed reference image than the compressive SAB method. Thus, while both architectures achieve a significant reduction in sampling rate, system complexity and area, the quadrature SAB method achieves better image quality. Future work may involve the addition of multiple receiver channels and the development of an integrated system-on-chip.Open Acces

Neuromorphic silicon neuron circuits

23 páginas, 21 figuras, 2 tablas.-- et al.Hardware implementations of spiking neurons can be extremely useful for a large variety of applications, ranging from high-speed modeling of large-scale neural systems to real-time behaving systems, to bidirectional brain–machine interfaces. The specific circuit solutions used to implement silicon neurons depend on the application requirements. In this paper we describe the most common building blocks and techniques used to implement these circuits, and present an overview of a wide range of neuromorphic silicon neurons, which implement different computational models, ranging from biophysically realistic and conductance-based Hodgkin–Huxley models to bi-dimensional generalized adaptive integrate and fire models. We compare the different design methodologies used for each silicon neuron design described, and demonstrate their features with experimental results, measured from a wide range of fabricated VLSI chips.This work was supported by the EU ERC grant 257219 (neuroP), the EU ICT FP7 grants 231467 (eMorph), 216777 (NABAB), 231168 (SCANDLE), 15879 (FACETS), by the Swiss National Science Foundation grant 119973 (SoundRec), by the UK EPSRC grant no. EP/C010841/1, by the Spanish grants (with support from the European Regional Development Fund) TEC2006-11730-C03-01 (SAMANTA2), TEC2009-10639-C04-01 (VULCANO) Andalusian grant num. P06TIC01417 (Brain System), and by the Australian Research Council grants num. DP0343654 and num. DP0881219.Peer Reviewe

Analog Signal Processing Elements for Energy-Constrained Platforms

Energy constrained processing poses a number of challenges that have resulted in tremendous innovations over the past decade. Shrinking supply voltages and limited clock speeds have placed an emphasis on processing efficiency over the raw throughput of a processor. One of the approaches to increase processing efficiency is to use parallel processing with slower, lower resolution processing elements. By utilizing this parallel approach, power consumption can be decreased while maintaining data throughput relative to other more power-hungry architectures.;This low resolution / parallel architecture has direct application in the analog as well as the digital domain. Indeed, research shows that as the resolution of a signal processor falls below a system-dependent threshold, it is almost always more efficient to preform the processing in the analog domain. These continuous-time circuits have long been used in the most energy-constrained applications, ranging from pacemakers and cochlear implants to wireless sensor motes designed to run autonomously for months in the field.;Most audio processing techniques utilize spectral decomposition as the first step of their algorithms, whether by a FFT/DFT in the digital domain or a bank of bandpass filters in the analog domain. The work presented here is designed to function within the parallel, array-based environment of a bank of bandpass filters. Work to improve the simulation of programmable analog storage elements (Floating-Gate transistors) in typical SPICE-based simulators is presented, along with a novel method of harnessing the unique properties of these Floating-Gate (FG) transistors to extend the linear range of a differential pair. These improvements in simulation and linearity are demonstrated in a Variable-Gain Amplfier (VGA) to compress large differential inputs into small single-ended outputs suitable for processing by other analog elements. Finally, a novel circuit composed of only six transistors is proposed to compute the continuous-time derivative of a signal within the sub-banded architecture of the bandpass filter bank

Strategies for enhancing DC gain and settling performance of amplifiers

The operational amplifier (op amp) is one of the most widely used and important building blocks in analog circuit design. High gain and high speed are two important properties of op amps because they determine the settling behavior of the op amps. As supply voltages decrease, the realization of high gain amplifiers with large Gain-Bandwidth-Products (GBW) has become challenging. The major focus in this dissertation is on the negative output impedance gain enhancement technique. The negative impedance gain enhancement technique offers potential for achieving very high gain and energy-efficient fast settling and is low-voltage compatible. Misconceptions that have limited the practical adoption of this gain enhancement technique are discussed. A new negative conductance gain enhancement technique was proposed. The proposed circuit generates a negative conductance with matching requirements for achieving very high DC gain that are less stringent than those for existing -g m gain enhancement schemes. The proposed circuit has potential for precise digital control of a very large DC gain. A prototype fully differential CMOS operational amplifier was designed and fabricated based on the proposed gain enhancement technique. Experimental results which showed a DC gain of 85dB and an output swing of 876mVp-p validated the fundamental performance characteristics of this technique. In a separate section, a new amplifier architecture with bandpass feedforward compensation is presented. It is shown that a bandpass feedforward path can be used to substantially extend the unity-gain-frequency of an operational amplifier. Simulation results predict significant improvements in rise time and settling performance and show that the bandpass compensation scheme is reasonably robust. In the final section, a new technique for asynchronous data recovery based upon using a delay line in the incoming data path is introduced. The proposed data recovery system is well suited for tight tolerance channels and coding systems supporting standards that limit the maximum number of consecutive 0\u27s and 1\u27s in a data stream. This system does not require clock recovery, suffers no loss of data during acquisition, has a reduced sensitivity to jitter in the incoming data and does not exhibit jitter enhancement associated with VCO tracking in a PLL

CMOS Hyperbolic Sine ELIN filters for low/audio frequency biomedical applications

Hyperbolic-Sine (Sinh) filters form a subclass of Externally-Linear-Internally-Non- Linear (ELIN) systems. They can handle large-signals in a low power environment under half the capacitor area required by the more popular ELIN Log-domain filters. Their inherent class-AB nature stems from the odd property of the sinh function at the heart of their companding operation. Despite this early realisation, the Sinh filtering paradigm has not attracted the interest it deserves to date probably due to its mathematical and circuit-level complexity. This Thesis presents an overview of the CMOS weak inversion Sinh filtering paradigm and explains how biomedical systems of low- to audio-frequency range could benefit from it. Its dual scope is to: consolidate the theory behind the synthesis and design of high order Sinh continuous–time filters and more importantly to confirm their micro-power consumption and 100+ dB of DR through measured results presented for the first time. Novel high order Sinh topologies are designed by means of a systematic mathematical framework introduced. They employ a recently proposed CMOS Sinh integrator comprising only p-type devices in its translinear loops. The performance of the high order topologies is evaluated both solely and in comparison with their Log domain counterparts. A 5th order Sinh Chebyshev low pass filter is compared head-to-head with a corresponding and also novel Log domain class-AB topology, confirming that Sinh filters constitute a solution of equally high DR (100+ dB) with half the capacitor area at the expense of higher complexity and power consumption. The theoretical findings are validated by means of measured results from an 8th order notch filter for 50/60Hz noise fabricated in a 0.35μm CMOS technology. Measured results confirm a DR of 102dB, a moderate SNR of ~60dB and 74μW power consumption from 2V power supply

Hybrid DDS-PLL based reconfigurable oscillators with high spectral purity for cognitive radio

Analytical, design and simulation studies on the performance optimization of reconfigurable architecture of a Hybrid DDS – PLL are presented in this thesis. The original contributions of this thesis are aimed towards the DDS, the dithering (spur suppression) scheme and the PLL. A new design of Taylor series-based DDS that reduces the dynamic power and number of multipliers is a significant contribution of this thesis. This thesis compares dynamic power and SFDR achieved in the design of varieties of DDS such as Quartic, Cubic, Linear and LHSC. This thesis proposes two novel schemes namely “Hartley Image Suppression” and “Adaptive Sinusoidal Interference Cancellation” overcoming the low noise floor of traditional dithering schemes. The simulation studies on a Taylor series-based DDS reveal an improvement in SFDR from 74 dB to 114 dB by using Least Mean Squares -Sinusoidal Interference Canceller (LM-SIC) with the noise floor maintained at -200 dB. Analytical formulations have been developed for a second order PLL to relate the phase noise to settling time and Phase Margin (PM) as well as to relate jitter variance and PM. New expressions relating phase noise to PM and lock time to PM are derived. This thesis derives the analytical relationship between the roots of the characteristic equation of a third order PLL and its performance metrics like PM, Gardner’s stability factor, jitter variance, spur gain and ratio of noise power to carrier power. This thesis presents an analysis to relate spur gain and capacitance ratio of a third order PLL. This thesis presents an analytical relationship between the lock time and the roots of its characteristic equation of a third order PLL. Through Vieta’s circle and Vieta’s angle, the performance metrics of a third order PLL are related to the real roots of its characteristic equation