Integration of broadband direct-conversion quadrature modulators

To increase spectral efficiency, transmitters usually send only one of the information carrying sidebands centered around a single radio-frequency carrier. The close-lying mirror, or image, sideband will be eliminated either by the filtering method or by the phasing method. Since filter Q-values rise in direct relation to the transmitted frequencies, the filtering method is generally not feasible for integrated microwave transmitters. A quadrature modulator realizes the phasing method by combining signals phased at quadrature (i.e. at 90° offsets) to produce a single-sideband (SSB) output. In this way output filtering can be removed or its specifications greatly relieved so as to produce an economical microwave transmitter. The proliferation of integrated circuit (IC) technologies since the 1980s has further boosted the popularity of quadrature modulator as an IC realization makes possible the economical production of two closely matched doubly balanced mixers, which suppress carrier and even-order spurious leakage to circuit output. Another strength of IC is its ability to perform microwave quadrature generation accurately on-chip, and thereby to avoid most of the interconnect parasitics which could ruin high-frequency quadrature signaling. Nevertheless, all quadrature modulator implementations are sensitive to phasing and amplitude errors, which are born as a result of mismatches, from the use of inaccurate differential signaling, and from inadequacies in the phasing circuitry itself. A 2° phase error is easily produced, and it reduces the image-rejection ratio (IRR) to −30 dBc. Therefore, as baseband signals synthesized by digital signal processing (DSP) are sufficiently accurate, this thesis concentrates on analyzing and producing the microwave signal path of a direct-conversion quadrature modulator with special emphasis on broadband, multimode radio-compatible operation. A model of the direct-conversion quadrature modulator operation has been developed, which reveals the effect the circuit non-linearities and mismatch-related offsets have on available performance. Further, theoretical proof is given of the well-known property of improving differential signal balance that cascaded differential pairs exhibit. Among the practical results, a current reuse mixer has been developed, which improves the transmitted signal-to-noise-ratio (SNR) by 3 dB, with a maximum measured dynamic range of +158 dB. The complementary bipolar process was further used to extend the bipolar push-pull stage bandwidth to 9.5 GHz. At the core of this work is the parallel switchable polyphase (PP) filter quadrature generator that was developed, since it makes possible accurate broadband IQ generation without the high loss that usually results from the application of PP filtering. Two IQ modulator prototypes were realized to test simulated and theoretically derived data: the 0.8 µm SiGe IC achieves an IRR better than −40 dBc over 0.75-3.6 GHz, while the 0.13 µm digital bulk CMOS IC achieves better than −37 dBc over 0.56-4.76 GHz. For this IRR performance the SiGe prototype boasts the inexpensive solution of integrated baluns, while the CMOS one utilizes a coil-transmission line hybrid transformer at its LO input to drive the switchable PP filters.Taajuuksien käytön tehostamiseksi lähettimet lähettävät yleensä vain toisen informaatiota sisältävistä sivukaistoistaan yhdelle radiotaajuuksiselle kantoaallolle keskitettynä. Viereinen peilitaajuus eli sivukaista vaimennetaan joko suodattamalla tai vaiheistamalla signalointia sopivasti. Koska suodattimen hyvyysluvut nousevat suorassa suhteessa käytettyyn taajuuteen, ei suodatusmenetelmä ole yleensä mahdollinen mikroaaltotaajuusalueen lähettimissä. Kvadratuurimodulaattori toteuttaa vaiheistusmenetelmän yhdistämällä 90-asteen vaihesiirroksin vaiheistetut signaalit yksisivukaistaisen lähetteen tuottamiseksi. Näin voidaan korvata lähdön suodatus joko kokonaan tai lieventämällä vaadittavia suoritusarvoja, jolloin mikroaaltoalueen lähetin voidaan tuottaa taloudellisesti. Integroitujen piiriratkaisujen yleistyminen 1980-luvulta lähtien on edesauttanut kvadratuurimodulaattorin suosiota, koska integroidulle piirille voidaan taloudellisesti tuottaa kaksi hyvin ominaisuuksiltaan toisiaan vastaavaa kaksoisbalansoitua sekoitinta, ja nämä tunnetusti vaimentavat kantoaaltovuotoa ja parillisia harmoonisia piirin lähdössä. Toinen integroitujen piirien vahvuus on kyky tarkkaan mikroaaltoalueen kvadratuurisignalointiin samalla piirillä, jolloin vältetään suurin osa kytkentöjen parasiittisista jotka muutoin voisivat tuhota korkeataajuuksisen 90-asteen vaiheistuksen. Kaikki kvadratuurimodulaattorit ovat joka tapauksessa herkkiä vaiheistus- ja amplitudieroille, joita syntyy komponenttiarvojen satunnaishajonnasta, epätarkan differentiaalisen signaloinnin käytöstä, ja itse vaiheistuspiiristön puutteellisuuksista. Kahden asteen vaihevirhe syntyy helposti, ja tällöin sivukaistavaimennus heikkenee -30 dBc:n tasolle. Tämänvuoksi, ja olettaen että digitaalisella signaaliprosessorilla luotu kantataajuuksinen signalointi on riittävän tarkkaa, tämä väitöskirja keskittyy kvadratuurimodulaattorin mikroaaltotaajuuksisen signaalipolun analysointiin ja tuottamiseen painottaen erityisesti laajakaistaista, monisovellusradioiden kanssa yhteensopivaa toimivuutta. Kvadratuurimodulaattorin toimintamallia on kehitetty siten, että mallissa huomioidaan epälineaarisuuksien ja piirielementtien satunnaishajontojen vaikutus saavutettavalle suorituskyvylle. Lisäksi on teoreettisesti todistettu sinänsä hyvin tunnettu peräkkäin kytkettyjen vahvistinasteiden differentiaalisen signaloinnin symmetrisyyttä parantava vaikutus. Käytännön tuloksista voidaan mainita kehitetty virtaakierrättävä sekoitin, joka parantaa signaali-kohinasuhdetta +3 dB, suurimman mitatun dynaamisen alueen ollessa +158 dB. Samaa komplementaarista bipolaariprosessia käytettiin edelleen bipolaarisen vuorovaihe-asteen kaistan levittämisessä 9.5 GHz:iin. Yhtenä tämän työn tärkeimmistä tuloksista on kehitetty kytkimin valittavista rinnakkaisista monivaihesuodattimista koostuva kvadratuurigeneraattori, jolla on mahdollista tuottaa laajakaistaista IQ-signalointia ilman suurta häviötä joka yleensä liittyy monivaihesuodattimien käyttöön. Kaksi IQ-modulaattoriprototyyppiä toteutettiin simuloitujen ja teoreettisesti mallinnettujen tulosten testaamiseksi: 0.8 µm SiGe integroitu piiri saavuttaa paremman sivukaistavaimennuksen kuin -40 dBc yli 0.75-3.6 GHz, kun taas 0.13 µm digitaalipiirien tuottamiseen tarkoitetulla CMOS prosessilla toteutettu integroitu piiri saavuttaa paremman sivukaistavaimennuksen kuin -37 dBc taajuusalueella 0.56-4.76 GHz. Näihin sivukaistavaimennuksiin SiGe prototyyppi pääsee edullisesti integroiduin symmetrointimuuntajin, kun taas CMOS piirillä käytetään kela-siirtojohto-tyyppistä yhdistelmämuuntajaa LO-sisääntulossa josta ajetaan erikseen kytkettäviä monivaihesuodattimia.reviewe

Design and implementation of a downlink MC-CDMA receiver

Cette thèse présente une étude d'un système complet de transmission en liaison descendante utilisant la technologie multi-porteuse avec l'accès multiple par division de code (Multi-Carrier Code Division Multiple Access, MC-CDMA). L'étude inclut la synchronisation et l'estimation du canal pour un système MC-CDMA en liaison descendante ainsi que l'implémentation sur puce FPGA d'un récepteur MC-CDMA en liaison descendante en bande de base. Le MC-CDMA est une combinaison de la technique de multiplexage par fréquence orthogonale (Orthogonal Frequency Division Multiplexing, OFDM) et de l'accès multiple par répartition de code (CDMA), et ce dans le but d'intégrer les deux technologies. Le système MC-CDMA est conçu pour fonctionner à l'intérieur de la contrainte d'une bande de fréquence de 5 MHz pour les modèles de canaux intérieur/extérieur pédestre et véhiculaire tel que décrit par le "Third Genaration Partnership Project" (3GPP). La composante OFDM du système MC-CDMA a été simulée en utilisant le logiciel MATLAB dans le but d'obtenir des paramètres de base. Des codes orthogonaux à facteur d'étalement variable (OVSF) de longueur 8 ont été choisis comme codes d'étalement pour notre système MC-CDMA. Ceci permet de supporter des taux de transmission maximum jusquà 20.6 Mbps et 22.875 Mbps (données non codées, pleine charge de 8 utilisateurs) pour les canaux intérieur/extérieur pédestre et véhiculaire, respectivement. Une étude analytique des expressions de taux d'erreur binaire pour le MC-CDMA dans un canal multivoies de Rayleigh a été réalisée dans le but d'évaluer rapidement et de façon précise les performances. Des techniques d'estimation de canal basées sur les décisions antérieures ont été étudiées afin d'améliorer encore plus les performances de taux d'erreur binaire du système MC-CDMA en liaison descendante. L'estimateur de canal basé sur les décisions antérieures et utilisant le critère de l'erreur quadratique minimale linéaire avec une matrice' de corrélation du canal de taille 64 x 64 a été choisi comme étant un bon compromis entre la performance et la complexité pour une implementation sur puce FPGA. Une nouvelle séquence d'apprentissage a été conçue pour le récepteur dans la configuration intérieur/extérieur pédestre dans le but d'estimer de façon grossière le temps de synchronisation et le décalage fréquentiel fractionnaire de la porteuse dans le domaine du temps. Les estimations fines du temps de synchronisation et du décalage fréquentiel de la porteuse ont été effectués dans le domaine des fréquences à l'aide de sous-porteuses pilotes. Un récepteur en liaison descendante MC-CDMA complet pour le canal intérieur /extérieur pédestre avec les synchronisations en temps et en fréquence en boucle fermée a été simulé avant de procéder à l'implémentation matérielle. Le récepteur en liaison descendante en bande de base pour le canal intérieur/extérieur pédestre a été implémenté sur un système de développement fabriqué par la compagnie Nallatech et utilisant le circuit XtremeDSP de Xilinx. Un transmetteur compatible avec le système de réception a également été réalisé. Des tests fonctionnels du récepteur ont été effectués dans un environnement sans fil statique de laboratoire. Un environnement de test plus dynamique, incluant la mobilité du transmetteur, du récepteur ou des éléments dispersifs, aurait été souhaitable, mais n'a pu être réalisé étant donné les difficultés logistiques inhérentes. Les taux d'erreur binaire mesurés avec différents nombres d'usagers actifs et différentes modulations sont proches des simulations sur ordinateurs pour un canal avec bruit blanc gaussien additif

RF Power Amplifier and Its Envelope Tracking

This dissertation introduces an agile supply modulator with optimal transient performance for the envelope tracking supply in linear power amplifiers. For this purpose, an on-demand current source module, the bang-bang transient performance enhancer (BBTPE), is proposed. Its objective is to follow fast variations in input signals with reduced overshoot and settling time without deteriorating the steady-state performance of the buck regulator. The proposed approach enables fast system response through the BBTPE and an accurate steady-state output response through a low switching ripple and power efficient dynamic buck regulator. Fast output response with the help of the added module induces a slower rise of inductor current in the buck converter that further assists the proposed system to reduce both overshoot and settling time. To demonstrate the feasibility of the proposed solution, extensive simulations and experimental results from a discrete system are reported. The proposed supply modulator shows 80% improvement in rise time along with 60% reduction in both overshoot and settling time compared to the conventional dynamic buck regulator-based solution. Experimental results for a PA using the LTE 16-QAM 5 MHz standard shows improvement of 7.68 dB and 65.1% in ACPR and EVM, respectively. In a polar power amplifier, the input signal splits into phase and amplitude components using a non-linear conversion operation. This operation broadens the spectrum of the polar signal components. The information of amplitude and phase contains spectral images due to the sampling operation in non-linear conversion operation. These spectral images can be large and cause out-of-band emission in the output spectrum. In addition, during the recombination process of phase and amplitude, a delay mismatch between amplitude and phase signals, which can occur due to separate processing paths of amplitude and phase signals, causes out-of-band emissions, also known as spectral regrowth. This dissertation presents solutions to both of the issues of digital polar power amplifier: spectral images and delay mismatch. In order to reduce the problem of spectral images, interpolation of phase and amplitude is proposed in this work. This increases the effective sampling frequency of the amplitude and phase, which helps to improve the linearity by around 10 dB. In addition, a novel calibration scheme is proposed here for the delay mismatch between phase and amplitude path in a digital polar power amplifier. The scheme significantly reduces the spectral regrowth. The scheme uses the same path for phase and amplitude delay calculation after the recombination that allows having a robust calibration. Furthermore, it can be executed during the empty transmission slots. The proposed scheme is designed in a 40 nm CMOS technology and simulated with a 64-QAM IEEE 802.11n wireless standard. The scheme achieved 7.57 dB enhancement in ACLR and 84.35% improvement in EVM for a 3.5 ns mismatch in phase and amplitude path

Power-Efficient Design Techniques and Architectures for Scalable Submicron Analog Circuits

As the CMOS process scales down to submicron, digital circuit performance improves, while reduced supply voltage and lower transistor intrinsic gain make it difficult to implement analog circuits in a power efficient manner. Therefore, it has become advantageous to shift more analog signal processing functions conventionally realized in voltage (analog) domain into utilizing charge or time as the variable that can be processed by mostly digital/passive circuits. In this thesis, both circuit-level techniques and architectures are proposed that are inherently compatible with transistor scaling in submicron CMOS, meanwhile achieving state-of-the-art performance and optimizing power efficiency. The first part focuses on a highly reconfigurable charge-domain switched-g[subscript m]-C biquad band-pass filter (BPF) topology that utilizes an interleaved semi-passive charge sharing technique. It uses only switches, capacitors, linearity-enhanced gm-stages and digital circuitry for a 3-phase non-overlapping clock scheme. Flexible tunability in both center frequency and -3dB bandwidth is achieved with a scaling-compatible implementation. A 4th-order BPF prototype operating at a 1.2GS/s sampling rate is designed with a cascade of two proposed biquads in a 65nm LPE CMOS process. A tunable center frequency of 35−70MHz is measured with programmable bandwidth and a maximum stop-band rejection of 72dB. The measured in-band IIP3 is +12.5dBm. The filter prototype consumes 7.5mW total power from a 1.2V supply voltage, and occupies a core area of 0.17mm². In the second part, a highly linear continuous-time low-pass filter (LPF) topology with source follower coupling is presented that achieves excellent power efficiency. It synthesizes a 3rd-order low-pass transfer function in a single stage using coupled source followers and three capacitors, and can be configured to 2nd-order by disconnecting a capacitor. A 5th-order Butterworth prototype is designed with a cascade of two proposed filter stages in a 0.18μm CMOS, and occupies a core area of 0.12mm². Operating with a 1.3V supply voltage, the filter consumes only 0.5mA current, and achieves a -3dB bandwidth of 20MHz with 82dB stop-band rejection. A total harmonic distortion (THD) of -39.5dB at the output is measured with a +6.6dBm (i.e. 1.35V[subscript pk-pk]) input signal at 2MHz. The measured in-band IIP3 is +28.8dBm. The dynamic range (at 1% THD) is 76.8dB, with 15.3nV/√Hz averaged in-band input-referred noise. A pseudo-differential-VCO based 2nd-order continuous-time ΔΣ ADC with a residue self-coupling technique is proposed and implemented with mostly digital circuits in the third part. Two VCOs are arranged in a pseudo-differential manner. The digital output is obtained by comparing the sampled output phase of one VCO with that of the other. Passive subtraction is realized in current domain to obtain the residue at the VCO input. The residue self-coupling is implemented using a linear 1st-order transconductance low-pass filter (TCLPF). Moreover, a highly linear VCO topology is presented. The transistor-level simulations in a 65nm CMOS process show a 78dB SNDR over a 10MHz signal bandwidth with a power consumption of 2.9mW, which is 16dB improvement in contrast to the case with the TCLPF block powered off

RF Power Amplifier and Its Envelope Tracking

This dissertation introduces an agile supply modulator with optimal transient performance for the envelope tracking supply in linear power amplifiers. For this purpose, an on-demand current source module, the bang-bang transient performance enhancer (BBTPE), is proposed. Its objective is to follow fast variations in input signals with reduced overshoot and settling time without deteriorating the steady-state performance of the buck regulator. The proposed approach enables fast system response through the BBTPE and an accurate steady-state output response through a low switching ripple and power efficient dynamic buck regulator. Fast output response with the help of the added module induces a slower rise of inductor current in the buck converter that further assists the proposed system to reduce both overshoot and settling time. To demonstrate the feasibility of the proposed solution, extensive simulations and experimental results from a discrete system are reported. The proposed supply modulator shows 80% improvement in rise time along with 60% reduction in both overshoot and settling time compared to the conventional dynamic buck regulator-based solution. Experimental results for a PA using the LTE 16-QAM 5 MHz standard shows improvement of 7.68 dB and 65.1% in ACPR and EVM, respectively. In a polar power amplifier, the input signal splits into phase and amplitude components using a non-linear conversion operation. This operation broadens the spectrum of the polar signal components. The information of amplitude and phase contains spectral images due to the sampling operation in non-linear conversion operation. These spectral images can be large and cause out-of-band emission in the output spectrum. In addition, during the recombination process of phase and amplitude, a delay mismatch between amplitude and phase signals, which can occur due to separate processing paths of amplitude and phase signals, causes out-of-band emissions, also known as spectral regrowth. This dissertation presents solutions to both of the issues of digital polar power amplifier: spectral images and delay mismatch. In order to reduce the problem of spectral images, interpolation of phase and amplitude is proposed in this work. This increases the effective sampling frequency of the amplitude and phase, which helps to improve the linearity by around 10 dB. In addition, a novel calibration scheme is proposed here for the delay mismatch between phase and amplitude path in a digital polar power amplifier. The scheme significantly reduces the spectral regrowth. The scheme uses the same path for phase and amplitude delay calculation after the recombination that allows having a robust calibration. Furthermore, it can be executed during the empty transmission slots. The proposed scheme is designed in a 40 nm CMOS technology and simulated with a 64-QAM IEEE 802.11n wireless standard. The scheme achieved 7.57 dB enhancement in ACLR and 84.35% improvement in EVM for a 3.5 ns mismatch in phase and amplitude path

Engineering evaluations and studies. Volume 3: Exhibit C

High rate multiplexes asymmetry and jitter, data-dependent amplitude variations, and transition density are discussed

Sensores passivos alimentados por transmissão de energia sem fios para aplicações de Internet das coisas

Nowadays, the Wireless Sensor Networks (WSNs) depend on the battery duration of the sensors and there is a renewed interest in creating a passive sensor network scheme in the area of Internet of Things (IoT) and space oriented WSN systems. The challenges for the future of radio communications have a twofold evolution, one being the low power consumption and, another, the adaptability and intelligent use of the available resources. Specially designed radios should be used to reduce power consumption, and adapt to the environment in a smart and e cient way. This thesis will focus on the development of passive sensors based on low power communication (backscatter) with Wireless Power Transfer (WPT) capabilities used in IoT applications. In that sense, several high order modulations for the communication will be explored and proposed in order to increase the data rate. Moreover, the sensors need to be small and cost e ective in order to be embedded in other technologies or devices. Consequently, the RF front-end of the sensors will be designed and implemented in Monolithic Microwave Integrated Circuit (MMIC).Atualmente, as redes de sensores sem fios dependem da duração da bateria e,deste modo, existe um interesse renovado em criar um esquema de rede de sensores passivos na área de internet das coisas e sistemas de redes de sensores sem fios relacionados com o espaço. Os desafios do futuro das comunicações de rádio têm uma dupla evolução, sendo um o baixo consumo de energia e, outro, a adaptação e o uso inteligente dos recursos disponíveis. Rádios diferentes dos convencionais devem ser usados para reduzir o consumo de energia e devem adaptar-se ao ambiente de forma inteligente e eficiente, de modo a que este use a menor quantidade de energia possível para estabelecer a comunicação. Esta tese incide sobre o desenvolvimento de sensores passivos baseados em comunicação de baixo consumo energético (backscatter) com recurso a transmissão de energia sem fios de modo a que possam ser usados em diferentes aplicações inseridas na internet das coisas. Nesse sentido, várias modulações de alta ordem para a comunicação backscatter serão exploradas e propostas com o objectivo de aumentar a taxa de transmissão de dados. Além disso, os sensores precisam de ser reduzidos em tamanho e económicos de modo a serem incorporados em outras tecnologias ou dispositivos. Consequentemente, o front-end de rádio frequência dos sensores será projetado e implementado em circuito integrado de microondas monolítico.Programa Doutoral em Engenharia Eletrotécnic

Physical waveform research for beyond 52.6 GHz in 5G NR networks

Historically, in order to fulfil all the requirements for the new generations, the frequency bands have been expanded from generation to generation. In particular for the fifth generation new radio (5G NR), where the use of millimetre wave (mmWave) frequencies can offer higher bandwidths, communications in frequencies beyond 52.6 GHz seem really promising and are now under discussion in the 3rd Generation Partnership Project (3GPP) standardisation for the 5G NR future releases. More concretely, both academia and industry are doing research for the frequency range between 52.6 GHz and 114.25 GHz. The reasons why communications beyond 52.6 GHz are interesting is because in those frequencies, high data rate and low latency can be provided due to the large and contiguous channel bandwidth that is available. Also, new use cases can be explored in this frequency range since high accuracy positioning is possible at higher carrier frequencies, such as Orthogonal Frequency Division Multiplexing (OFDM) radar sensing, that allows new kinds of services. New challenges appear at higher frequencies, or other implementation issues that were not critical in lower frequencies start to become dominant and have to be taken into consideration while defining the new modulations and comparing the possible candidates. The main problems that have to be faced at higher frequencies are the poor propagation conditions (propagation losses are higher than in frequencies below 52.6 GHz), and the radio frequency (RF) impairments that electronic components may have, especially the lower power amplifier (PA) efficiency. Therefore, in order to have a good signal quality, if the peak to average power ratio (PAPR) of the original signal is high, the back-off should be high to make the PA work in the linear region. Thus, the waveform design has to be focused on generating signals with “nearly constant” envelope in order to be able to work closer to the saturation zone of the amplifier without distorting the signal. Also, another problem that has to be taken into account is the large phase noise (PN) present at these frequencies. The main goal of this work is the comparison between different modulations for discrete Fourier transform (DFT) Spread OFDM (DFTs-OFDM) in order to find a suitable candidate that can be part of the 5G NR communications for carrier frequencies beyond 52.6 GHz, and targeting specially low spectral efficiency (between 1 and 2 bps/Hz). Therefore, the main modulation references are pulse shaped π/2- binary phase shift keying (BPSK) and quadrature phase shift keying (QPSK) supported in 5G NR Release 15 up link (UL). In this Thesis, several modulation candidates have been tested under realistic conditions by using a 3GPP 5G NR compliant radio link simulator in Matlab. In order to find the best candidate, the waveforms should be able to present good characteristics that can overcome the problems present in mmWave communications. The main contribution of this thesis is to propose a new "constrained" phase shift keying (PSK) modulation, called CPSK, which applies a constraint to the symbols that are transmitted in order to reduce the PAPR of the signal. The results have shown that under the mmWave communications conditions (such as low PA efficiency and high PN), the new CPSK modulations can provide significant improvement with the evaluated PA model when compared to QPSK modulation, and together with extensive link level performance evaluations, a clear link budget gain can also be shown for specific CPSK modulation candidates and pulse shaped π/2-BPSK

Digital Radio Encoding and Power Amplifier Design for Multimode and Multiband Wireless Communications

The evolution of wireless technology has necessitated the support of multiple communication standards by mobile devices. At present, multiple chipsets/radios operating at predefined sets of modulation schemes, frequency bands, bandwidths and output power levels are used to achieve this objective. This leads to higher component counts, increased cost and limits the capacity to cope with future communication standards. In order to tackle different wireless standards using a single chipset, digital circuits have been increasingly deployed in radios and demonstrated re-configurability in different modulation schemes (multimode) and frequency bands (multiband). Despite efforts and progress made in digitizing the entire radio, the power amplifier (PA) is still designed using an conventional approach and has become the bottleneck in digital transmitters, in terms of low average power efficiency, poor compatibility with modern CMOS technology and limited re-configurability. This research addresses these issues from two aspects. The first half of the thesis investigates signal encoding issues between the modulator and PA. We propose, analyze and evaluate a new hybrid amplitude/time signal encoding scheme that significantly improves the coding efficiency and dynamic range of a digitally modulated power amplifier (DMPA) without significantly increasing design complexity. The proposed hybrid amplitude/time encoding scheme combines both the amplitude domain and the time domain to optimally encode information. Experimental results show that hybrid amplitude/time encoding results in a 35% increase in the average coding efficiency with respect to conventional time encoding, and is only 6.7% lower than peak efficiency when applied to a Wireless Local Area Network (WLAN) signal with a peak to average power ratio equal to 9.9 dB. A new DMPA architecture, based on the proposed hybrid encoding, is also proposed. The second half of this thesis presents the design, analysis and implementation of a CMOS PA that is amenable to the proposed hybrid encoding scheme. A multi-way current mode class-D PA architecture has been proposed and realized in 130 nm CMOS technology. The designed PA has satisfied the objectives of wide bandwidth (1.5 GHz - 2.7 GHz at 1 dB output power), and high efficiency (PAE 63%) in addition to demonstrating linear responses using the proposed digital encoding. A complete digital transmitter combining the encoder and the multi-way PA was also investigated. The overall efficiency is 27% modulating 7.3 dB peak to average power ratio QAM signals