이동통신 기기에 적합한 재구성이 가능한 다중대역 선형 CMOS 전력증폭기에 관한 연구

학위논문 (박사)-- 서울대학교 대학원 : 전기·컴퓨터공학부, 2015. 2. 권영우.In this Dissertation, a study on multiband reconfigurable linear CMOS power amplifier (PA) is performed. Since a larger number of frequency bands is allocated for 3G/4G mobile communication standards nowadays, handset PAs are required to support the ever-increasing number of frequency bands. With the advent of high-speed wireless data transmission, handset PAs are also demanded to perform linear power amplification under the wide-band signal condition. Even though the CMOS technology has cost and size benefits, however, designing a watt-level linear CMOS PA is a challenging issue due to low breakdown voltage and nonlinear nature of the CMOS device. To resolve the issues above, this study presents two methods suitable for multiband (MB) linear CMOS PA: a reconfigurable MB matching structure and a linearization technique. The proposed MB structure shares a PA core to reduce the cost and size, and contains the power- and frequency-reconfigurable matching networks as well as the output path-selection function. Thus, it can perform the MB operation requiring multiple frequency bands and target output powers. The reconfiguration mechanism is quantitatively analyzed and experimentally demonstrated. The fabricated tri-band reconfigurable 3G UMTS PA using an InGaP/GaAs heterojunction bipolar transistor (HBT) process for practical handset application showed minimal efficiency degradation of less than 2% by multi-banding, compared with a single-band reference PA. For linearization of a CMOS PA, a phase-based linearization technique is presented. Since the PA nonlinearity is determined by the dynamic AM-AM and AM-PM, the two distortions should simultaneously be considered in linearization. Contrary to the previous works which have focused on the correction of AM-AM distortion by providing an envelope-dependent gate-bias, this work proposes an AM-PM linearizer using a varactor and an envelope-reshaping circuit. This linearizer helps the PA recover AM-AM distortion as well. To validate the usefulness of the proposed linearizer, 1.88 GHz and 0.9 GHz stacked-FET PAs using a 0.32-μm silicon-on-insulator (SOI) CMOS process were designed and fabricated. Measurement results showed that the fabricated 1.88 / 0.9 GHz linear CMOS PAs achieved linear efficiencies (meeting –39 dBc W-CDMA ACLR) of higher than 44 / 49%. Furthermore, a single-chain MB linear CMOS PA was implemented based on the proposed MB reconfiguration and linearization techniques. The fabricated MB PA, which has two outputs and covers five popular uplink UMTS/LTE bands (Band 1/2/4/5/8: 824 ~ 1980 MHz), showed minimal efficiency degradation (< 3.3%) compared to the single-band dedicated CMOS PA with W-CDMA efficiencies in excess of 40.7%. Finally, the signal-bandwidth limiting effect of the envelope-based linear CMOS PA is discussed and a solution is proposed. Due to the time delay during envelope-detection and shaping, a timing mismatch between the incoming RF signal and envelope-reshaped signal occurs, thus resulting in no linearization effect under wide-band signal (LTE 20 MHz or more) conditions. To resolve the problem, a group delay circuit with a compact size is employed and thus the linearization effect of the proposed phase-based linearizer is maintained up to 40 MHz LTE bandwidth.Abstract i Contents iii List of Tables vi List of Figures vii 1. Introduction 1 1.1 Motivation 1 1.2 Multiband PA Structure 4 1.3 Linearization of CMOS PA 6 1.4 Dissertation Organization 7 1.5 References 9 2. A Multiband Reconfigurable Power Amplifier for 3G UMTS Handset Applications 10 2.1 Introduction 10 2.2 Operation Principle of the Reconfigurable Output Matching Network 12 2.2.1 Power Reconfigurable Network (PRN) 14 2.2.2 Frequency Reconfigurable Network (FRN) 17 2.2.3 Path Selection Network (PSN) 20 2.2.4 Experimental Validation of the PRN and FRN 24 2.3 Fabrication and Measurement of a MB UMTS Reconfigurable PA 26 2.3.1 Design 26 2.3.2 Measurement 31 2.4 Summary 37 2.5 References 38 3. Linearization of CMOS Power Amplifier and Its Multiband Application 41 3.1 Introduction 41 3.2 Linearization of CMOS PAs: Prior Arts 43 3.3 Harmonic Termination 46 3.3.1 Operation Analysis 47 3.3.2 Experimental Validation 52 3.4 Control of Gate Bias Modulation Effect 54 3.4.1 Analysis 54 3.4.2 Experimental Validation 60 3.5 Proposed Linearization #1: Hybrid Bias 67 3.6 Proposed Linearization #2: Phase Injection 71 3.6.1 Motivation 71 3.6.2 Phase (Capacitance) Injection 72 3.7 Linear CMOS PA Design 75 3.7.1 Baseline PA Design 76 3.7.2 Linearizer Design 78 3.7.3 Fabrication 82 3.8 Measurement Results 83 3.8.1 CW Measurement 83 3.8.2 W-CDMA Measurement 84 3.8.3 LTE Measurement 87 3.9 A Single-Chain MB Reconfigurable Linear PA in SOI CMOS 90 3.9.1 MB Linear CMOS PA: Design 90 3.9.2 MB Linear CMOS PA: Measurement 94 3.10 Summary 99 3.11 References 100 4. Linearization of CMOS Power Amplifier Convering Wideband Signal 105 4.1 Introduction 105 4.2 Bandwidth Limitation of Envelope-Based Linearizers 106 4.2.1 Analysis 106 4.2.2 Delay Correction 110 4.2.3 Feedforward Envelope-Detection Structure with a Delay T/L 114 4.3 Group Delay Circuit 117 4.3.1 Positive GDC versus Negative GDC 117 4.3.2 Left-Handed T/L-Based GDC 119 4.4 Fabrication and Measurement 122 4.4.1 GDC Measurement 123 4.4.2 LTE Measurement 124 4.5 Summary 127 4.6 References 128 5. Conclusions 130 5.1 Research Summary 130 5.2 Future Works 132 Abstract in Korean 133 Publications 135Docto

Multiple beam antenna/switch system study

In the study of the Multiple Beam Antenna/Switch for the space to ground link (SGL) uplink and downlink services, several issues related to system engineering, antenna, transmit/receive, and switch systems were addressed and the results are provided. Bandwidth allocation at Ku band is inadequate to serve the data rate requirements for the forward and return services. Rain and depolarization effects at EHF, especially at Ka band, pose a significant threat to the link availabilities at heavy rain areas. Hardware induced effects such as the nonlinear characteristics of the power amplifier may necessitate the use of linearizers and limiters. It is also important to identify the components that are susceptible to the space radiation effects and shield or redesign them with rad-hard technologies for meeting the requirements of the space environment

Survey on individual components for a 5 GHz receiver system using 130 nm CMOS technology

La intención de esta tesis es recopilar información desde un punto de vista general sobre los diferentes tipos de componentes utilizados en un receptor de señales a 5 GHz utilizando tecnología CMOS. Se ha realizado una descripción y análisis de cada uno de los componentes que forman el sistema, destacando diferentes tipos de configuraciones, figuras de mérito y otros parámetros. Se muestra una tabla resumen al final de cada sección, comparando algunos diseños que se han ido presentando a lo largo de los años en conferencias internacionales de la IEEE.The intention of this thesis is to gather information from an overview point about the different types of components used in a 5 GHz receiver using CMOS technology. A review of each of the components that form the system has been made, highlighting different types of configurations, figure of merits and parameters. A summary table is shown at the end of each section, comparing many designs that have been presented over the years at international conferences of the IEEE.Departamento de Ingeniería Energética y FluidomecánicaGrado en Ingeniería en Electrónica Industrial y Automátic

Improving linearity utilising adaptive predistortion for power amplifiers at mm-wave frequencies

The large unlicensed 3 GHz overlapping bandwidth that is available worldwide at 60 GHz has resulted in renewed interest in 60 GHz technology. This frequency band has made it attractive for short-range gigabit wireless communication. The power amplifier (PA) directly influences the performance and quality of this entire communication chain, as it is one of the final subsystems in the transmitter. Spectral efficient modulation schemes used at 60 GHz pose challenging requirements for the linearity of the PA. To improve the linearity, several external linearisation techniques currently exist, such as feedback, feedforward, envelope elimination and restoration, linear amplification with non-linear components and predistortion. This thesis is aimed at investigating and characterising the distortion components found in PAs at mm-wave frequencies and evaluating whether an adaptive predistortion (APD) linearisation technique is suitable to reduce these distortion components. After a thorough literature study and mathematical analysis, it was found that the third-order intermodulation distortion (IMD3) components were the most severe distortion components. Predistortion was identified as the most effective linearisation technique in terms of minimising these IMD3 components and was therefore proposed in this research. It does not introduce additional complexity and can easily be integrated with the PA. Furthermore, the approach is stable and has lower power consumption when compared to the aforementioned linearisation techniques. The proposed predistortion technique was developed compositely through this research by making it a function of the PA’s output power that was measured using a power detector. A comparator was used with the detected output power and the reference voltages to control the dynamic bias circuit of the variable gain amplifier. This provided control and flexibility on when to apply the predistortion to the PA and therefore allowing the linearity of the PA to be optimised. Three-stage non-linear and linear PAs were also designed at 60 GHz and implemented to compare the performance of the APD technique and form part of the hypothesis verification process. The 130 nm silicon-germanium (SiGe) bipolar and complementary metal oxide semiconductor (BiCMOS) technology from IBM was used for the simulation of the entire APD and PA design and for the fabrication of the prototype integrated circuits (ICs). This technology has the advantage of integrating the high performance, low power intensive SiGe heterojunction bipolar transistors (HBTs) with the CMOS technology. The SiGe HBTs have a high cut-off frequency (fT > 200 GHz), which is ideal for mm-wave PA applications and the CMOS components were integrated in the control logic of the digital circuitry. The simulations and IC layout were accomplished with Cadence Virtuoso. The implemented IC occupies an area of 1.8 mm by 2.0 mm. The non-linear PA achieves a Psat of 11.97 dBm and an IP1dB of -10 dBm. With the APD technique applied, the linearity of the PA is significantly improved with an IP1dB of -6 dBm and an optimum IMD3 reduction of 10 dB. Based on the findings and results of the applied APD technique, APD reduced intermodulation distortion (especially the IMD3) and is thus suitable to improve the linearity of PAs at mm-wave frequencies. To the knowledge of this author, no APD technique has been applied for PAs at 60 GHz, therefore the contribution of this research will assist future PA designers to characterise and optimise the reduction of the IMD3 components. This will result in improved linear output power from the PA and the use of complex modulation schemes at 60 GHz.Thesis (PhD)--University of Pretoria, 2014.Electrical, Electronic and Computer EngineeringPh

Analysis and Design of CMOS Radio-Frequency Power Amplifiers

The continuous advancement of semiconductor technologies, especially CMOS technology, has enabled exponential growth of the wireless communication industry. This explosive growth in turn has completely changed people’s lives. The CMOS feature size scale down greatly benefits digital logic integrations, which result in more powerful, versatile, and economical digital signal processing. Further research and development has pushed analog, mixed-signal, and even radio-frequency (RF) circuit blocks to be implemented and integrated in CMOS. Future generations of wireless communication call for even further level of integration, and as of now, the only circuit block that is rarely integrated in CMOS along with other parts of the system is the power amplifier (PA). Due to the fact that the PA in a wireless communication system is the most power-hungry circuit block, the integration of RF PA in CMOS would potentially not only save the cost of the wireless communication system real estate, but also reduce power consumption since die-to-die connection loss can be eliminated. RF PA design involves handling large amounts of voltage and current at the radio frequencies, which in the present wireless communication standards are in the range of giga-hertz. Therefore, a good understanding of many aspects related to RF PA design is necessary. Theoretical analysis of the communication system, nonlinear effects of the PA, as well as the impedance matching network is systematically presented. The analysis of the nonlinear effects proposes a formal mathematical description of the multitone nonlinearity, and through its relationship with two-tone test, the proposed PA design methodology would greatly reduce the design time while improving the design accuracy. A thorough analysis of the available architecture and design techniques for efficiency and linearity enhancement of RF PA shows that despite tremendous amounts of research and development into this topic, the fundamental tradeoff between the two still limits the RF PA implementation largely within SiGe, GaAs, and InP technologies. A RF PA for Wideband Code-Division Multiple Access (WCDMA) application standard is proposed, designed, and implemented in CMOS that demonstrates the proposed segmentation technique that resolved the main tradeoff between power efficiency and linearity. The innovative architecture developed in this work is not limited to applications in the WCDMA communication protocol or the CMOS technology, although CMOS implementation would take advantage of the readily available digital resources

A fast engineering approach to high efficiency power amplifier linearization for avionics applications

This PhD thesis provides a fast engineering approach to the design of digital predistortion (DPD) linearizers from several perspectives: i) enhancing the off-line training performance of open-loop DPD, ii) providing robustness and reducing the computational complexity of the parameters identification subsystem and, iii) importing machine learning techniques to favor the automatic tuning of power amplifiers (PAs) and DPD linearizers with several free-parameters to maximize power efficiency while meeting the linearity specifications. One of the essential parts of unmanned aerial vehicles (UAV) is the avionics, being the radio control one of the earliest avionics present in the UAV. Unlike the control signal, for transferring user data (such as images, video, etc.) real-time from the drone to the ground station, large transmission rates are required. The PA is a key element in the transmitter chain to guarantee the data transmission (video, photo, etc.) over a long range from the ground station. The more linear output power, the better the coverage or alternatively, with the same coverage, better SNR allows the use of high-order modulation schemes and thus higher transmission rates are achieved. In the context of UAV wireless communications, the power consumption, size and weight of the payload is of significant importance. Therefore, the PA design has to take into account the compromise among bandwidth, output power, linearity and power efficiency (very critical in battery-supplied devices). The PA can be designed to maximize its power efficiency or its linearity, but not both. Therefore, a way to deal with this inherent trade-off is to design high efficient amplification topologies and let the PA linearizers take care of the linearity requirements. Among the linearizers, DPD linearization is the preferred solution to both academia and industry, for its high flexibility and linearization performance. In order to save as many computational and power resources as possible, the implementation of an open-loop DPD results a very attractive solution for UAV applications. This thesis contributes to the PA linearization, especially on off-line training for open-loop DPD, by presenting two different methods for reducing the design and operating costs of an open-loop DPD, based on the analysis of the DPD function. The first method focuses on the input domain analysis, proposing mesh-selecting (MeS) methods to accurately select the proper samples for a computationally efficient DPD parameter estimation. Focusing in the MeS method with better performance, the memory I-Q MeS method is combined with feature extraction dimensionality reduction technique to allow a computational complexity reduction in the identification subsystem by a factor of 65, in comparison to using the classical QR-LS solver and consecutive samples selection. In addition, the memory I-Q MeS method has been proved to be of crucial interest when training artificial neural networks (ANN) for DPD purposes, by significantly reducing the ANN training time. The second method involves the use of machine learning techniques in the DPD design procedure to enlarge the capacity of the DPD algorithm when considering a high number of free parameters to tune. On the one hand, the adaLIPO global optimization algorithm is used to find the best parameter configuration of a generalized memory polynomial behavioral model for DPD. On the other hand, a methodology to conduct a global optimization search is proposed to find the optimum values of a set of key circuit and system level parameters, that properly combined with DPD linearization and crest factor reduction techniques, can exploit at best dual-input PAs in terms of maximizing power efficiency along wide bandwidths while being compliant with the linearity specifications. The advantages of these proposed techniques have been validated through experimental tests and the obtained results are analyzed and discussed along this thesis.Aquesta tesi doctoral proporciona unes pautes per al disseny de linealitzadors basats en predistorsió digital (DPD) des de diverses perspectives: i) millorar el rendiment del DPD en llaç obert, ii) proporcionar robustesa i reduir la complexitat computacional del subsistema d'identificació de paràmetres i, iii) incorporació de tècniques d'aprenentatge automàtic per afavorir l'auto-ajustament d'amplificadors de potència (PAs) i linealitzadors DPD amb diversos graus de llibertat per poder maximitzar l’eficiència energètica i al mateix temps acomplir amb les especificacions de linealitat. Una de les parts essencials dels vehicles aeris no tripulats (UAV) _es l’aviònica, sent el radiocontrol un dels primers sistemes presents als UAV. Per transferir dades d'usuari (com ara imatges, vídeo, etc.) en temps real des del dron a l’estació terrestre, es requereixen taxes de transmissió grans. El PA _es un element clau de la cadena del transmissor per poder garantir la transmissió de dades a grans distàncies de l’estació terrestre. A major potència de sortida, més cobertura o, alternativament, amb la mateixa cobertura, millor relació senyal-soroll (SNR) la qual cosa permet l’ús d'esquemes de modulació d'ordres superiors i, per tant, aconseguir velocitats de transmissió més altes. En el context de les comunicacions sense fils en UAVs, el consum de potència, la mida i el pes de la càrrega útil són de vital importància. Per tant, el disseny del PA ha de tenir en compte el compromís entre ample de banda, potència de sortida, linealitat i eficiència energètica (molt crític en dispositius alimentats amb bateries). El PA es pot dissenyar per maximitzar la seva eficiència energètica o la seva linealitat, però no totes dues. Per tant, per afrontar aquest compromís s'utilitzen topologies amplificadores d'alta eficiència i es deixa que el linealitzador s'encarregui de garantir els nivells necessaris de linealitat. Entre els linealitzadors, la linealització DPD és la solució preferida tant per al món acadèmic com per a la indústria, per la seva alta flexibilitat i rendiment. Per tal d'estalviar tant recursos computacionals com consum de potència, la implementació d'un DPD en lla_c obert resulta una solució molt atractiva per a les aplicacions UAV. Aquesta tesi contribueix a la linealització del PA, especialment a l'entrenament fora de línia de linealitzadors DPD en llaç obert, presentant dos mètodes diferents per reduir el cost computacional i augmentar la fiabilitat dels DPDs en llaç obert. El primer mètode se centra en l’anàlisi de l’estadística del senyal d'entrada, proposant mètodes de selecció de malla (MeS) per seleccionar les mostres més significatives per a una estimació computacionalment eficient dels paràmetres del DPD. El mètode proposat IQ MeS amb memòria es pot combinar amb tècniques de reducció del model del DPD i d'aquesta manera poder aconseguir una reducció de la complexitat computacional en el subsistema d’identificació per un factor de 65, en comparació amb l’ús de l'algoritme clàssic QR-LS i selecció de mostres d'entrenament consecutives. El segon mètode consisteix en l’ús de tècniques d'aprenentatge automàtic pel disseny del DPD quan es considera un gran nombre de graus de llibertat (paràmetres) per sintonitzar. D'una banda, l'algorisme d’optimització global adaLIPO s'utilitza per trobar la millor configuració de paràmetres d'un model polinomial amb memòria generalitzat per a DPD. D'altra banda, es proposa una estratègia per l’optimització global d'un conjunt de paràmetres clau per al disseny a nivell de circuit i sistema, que combinats amb linealització DPD i les tècniques de reducció del factor de cresta, poden maximitzar l’eficiència de PAs d'entrada dual de gran ample de banda, alhora que compleixen les especificacions de linealitat. Els avantatges d'aquestes tècniques proposades s'han validat mitjançant proves experimentals i els resultats obtinguts s'analitzen i es discuteixen al llarg d'aquesta tesi

Analysis and Design of CMOS Radio-Frequency Power Amplifiers

The continuous advancement of semiconductor technologies, especially CMOS technology, has enabled exponential growth of the wireless communication industry. This explosive growth in turn has completely changed people’s lives. The CMOS feature size scale down greatly benefits digital logic integrations, which result in more powerful, versatile, and economical digital signal processing. Further research and development has pushed analog, mixed-signal, and even radio-frequency (RF) circuit blocks to be implemented and integrated in CMOS. Future generations of wireless communication call for even further level of integration, and as of now, the only circuit block that is rarely integrated in CMOS along with other parts of the system is the power amplifier (PA). Due to the fact that the PA in a wireless communication system is the most power-hungry circuit block, the integration of RF PA in CMOS would potentially not only save the cost of the wireless communication system real estate, but also reduce power consumption since die-to-die connection loss can be eliminated. RF PA design involves handling large amounts of voltage and current at the radio frequencies, which in the present wireless communication standards are in the range of giga-hertz. Therefore, a good understanding of many aspects related to RF PA design is necessary. Theoretical analysis of the communication system, nonlinear effects of the PA, as well as the impedance matching network is systematically presented. The analysis of the nonlinear effects proposes a formal mathematical description of the multitone nonlinearity, and through its relationship with two-tone test, the proposed PA design methodology would greatly reduce the design time while improving the design accuracy. A thorough analysis of the available architecture and design techniques for efficiency and linearity enhancement of RF PA shows that despite tremendous amounts of research and development into this topic, the fundamental tradeoff between the two still limits the RF PA implementation largely within SiGe, GaAs, and InP technologies. A RF PA for Wideband Code-Division Multiple Access (WCDMA) application standard is proposed, designed, and implemented in CMOS that demonstrates the proposed segmentation technique that resolved the main tradeoff between power efficiency and linearity. The innovative architecture developed in this work is not limited to applications in the WCDMA communication protocol or the CMOS technology, although CMOS implementation would take advantage of the readily available digital resources

A Novel Power-Scalable Wideband Power Amplifier Linearization Technique

Global mobile traffic is expected to continue to increase at an astonishing rate in the future, due to the ever-increasing number of mobile phone subscribers and the adoption of smart devices which generate significantly more mobile traffic. To satisfy this growth in demand, it is envisioned that future 5th Generation (5G) mobile networks will utilize lower powered small-cell base stations and base stations with large antenna arrays to greatly improve network coverage and capacity. A power amplifier (PA) is a critical component in a base station’s transmitter, required to boost the signal power such that it is high enough for transmission to the intended receiver. The design of the PA for 5G base stations, however, presents new challenges to designers. When driven with modern wideband communication signals, the PA must be both efficient and linear in order to minimize power consumption, improve reliability, maintain transmission accuracy, and avoid interference with neighbouring signals. In conventional high-powered macrocell base station designs, the aforementioned requirements are usually satisfied using a two-step procedure. First, the PA is designed using a Doherty power amplifier (DPA) topology, which has high efficiency, but poor linearity. Then, digital predistortion (DPD) linearization techniques are applied to ensure that the DPA attains the required linearity performance. However, for the lower-powered PAs needed in small cells and large antenna arrays, the relatively high power overhead of DPD techniques, which does not scale down as the power range of the PA decreases, make them unattractive PA linearization solutions. In response, a new PA linearization technique is proposed and developed in this thesis. It is based on the design and addition of a linearization amplifier (LA), an approach which can help the PA attain the required linearity even when it is driven with modern communication signals with very wide bandwidths. Of particular note, the LA’s power consumption is relatively low, it scales with the PA’s power range, and it does not increase with signal bandwidth. These qualities make it highly suitable for use with PAs in future 5G small-cell base stations and base stations with large antenna arrays. To validate the proposed technique’s effectiveness, a prototype circuit was designed, fabricated and applied to a high peak efficiency 6 W class AB PA with a centre frequency of 850 MHz. When stimulated by a wideband 40 MHz signal, the PA’s adjacent channel leakage ratio (ACLR) was improved by up to 13 dB after the addition of the LA. This enabled the PA to achieve an ACLR of about -45 dBc without the use of any other linearization techniques. Significant ACLR improvements were also observed for signals with even wider bandwidths of up to 160 MHz. Moreover, it was shown that the LA could be used in conjunction with a simple predistorter to further improve the efficiency and linearity of the class AB PA. Next, the LA is augmented with a conventional DPA design to form a new linear DPA topology that was able to achieve a better linearity-efficiency trade-off compared to the linearized class AB PA. To accomplish this, a study of the interactions between the LA and DPA circuitries was conducted and a design strategy was developed to determine the circuit parameters that maximized ACLR improvement while minimizing power consumption. For validation purposes, this strategy was applied to design a proof-of-concept prototype with a centre frequency of 800 MHz and a peak envelope power of 12 W. With the addition of the LA, a more than 11 dB improvement of the ACLR was obtained at the prototype’s output when it was driven with signals with up to 40 MHz of modulation bandwidth: an ACLR of about -45 dBc or better was achieved over wide average power range. As expected, the efficiency of the linear DPA topology remained significantly higher than the linearized class AB PA for all signals tested. Another challenge faced in particular by PAs in a large antenna array, is that it will experience dynamic load impedance variations due to antenna coupling. This unwanted variation in the load impedance can cause instability and significant distortions at the output of the PA that is difficult to remedy using conventional techniques. To address these issues, it is shown in the last part of this thesis that the LA can be used to mitigate this problem by minimizing the amount of load impedance variation seen by the PA due to antenna coupling, such that it remains closer to its optimal value, and by maintaining excellent linearization across a wide range of load impedance values

Dynamic nonlinear behavioral modeling and adaptive predistortion for RF transmitters

Motivation -- Nonlinear dynamic behaviour, two-and three-box models -- Objectives and outline of the thesis -- Two-Box models, de-embedding nonlinearities and dynamic memory effects -- Transmitter prototype -- Hammerstein and Wiener model construction -- Three-box oriented nonlinear model -- Three-box model's two-stage identification procedure -- Adaptive predistortion construction using single tone signal -- Hypothetical model and adaptive predistortion -- Construction of the complete predistorted system with a two-box model -- Complete predistorted system and linearization validation with CDMA signal

Compensation technique for nonlinear distortion in RF circuits for multi-standard wireless systems

Recent technological advances in the RF and wireless industry has led to the design requirement of more sophisticated devices which can meet stringent specifications of bandwidth, data rate and throughput. These devices are required to be extremely sensitive and hence any external interference from other systems can severely affect the device and the output. This thesis introduces the existing problem in nonlinear components in a multi-standard wireless system due to interfering signals and suggests potential solution to the problem. Advances in RF and wireless systems with emerging new communication standards have made reconfigurablility and tunability a very viable option. RF transceivers are optimised for multi-standard operation, where one band of frequency can act as an interfering signal to the other band. Due to the presence of nonlinear circuits in the transceiver chains such as power amplifiers, reconfigurable and tunable filters and modulators, these interfering signals produce nonlinear distortion products which can deform the output signal considerably. Hence it becomes necessary to block these interfering signals using special components. The main objective of this thesis is to analyse and experimentally verify the nonlinear distortions in various RF circuits such as reconfigurable and tunable filters and devise ways to minimize the overall nonlinear distortion in the presence of other interfering signals. Reconfigurbality and tunablity in filters can be achieved using components such as varactor diodes, PIN diodes and optical switches. Nonlinear distortions in such components are measured using different signals and results noted. The compensation method developed to minimize nonlinear distortions in RF circuits caused due to interfering signals is explored thoroughly in this thesis. Compensation method used involves the design of novel microstrip bandstop filters which can block the interfering signals and hence give a clean output spectrum at the final stage. Recent years have seen the emergence of electronic band gap technology which has “band gap” properties meaning that a bandstop response is seen within particular range of frequency. This concept was utilised in the design of several novel bandstop filters using defected microstrip structure. Novel tunable bandstop filters has been introduced in order to block the unwanted signal. Fixed single-band and dual-band filters using DMS were fabricated with excellent achieved results. These filters were further extended to tunable structures. A dual-band tunable filter with miniaturized size was developed and designed. The designed filters were further used in the compensation technique where different scenarios showing the effect of interfering signals in wireless transceiver were described. Mathematical analysis proved the validation of the use of a bandstop filter as an inter-stage component. Distortion improvements of around 10dB have been experimentally verified using a power amplifier as device under test. Further experimental verification was carried out with a transmitter which included reconfigurable RF filters and power amplifier where an improvement of 15dB was achieved