A CMOS spectrum analyzer frontend for cognitive radio achieving +25dBm IIP3 and −169 dBm/Hz DANL

A dual RF-receiver preceded by discrete-step attenuators is implemented in 65nm CMOS and operates from 0.3– 1.0 GHz. The noise of the receivers is reduced by cross-correlating the two receiver outputs in the digital baseband, allowing attenuation of the RF input signal to increase linearity. With this technique a displayed average noise level below -169 dBm/Hz is obtained with +25 dBm IIP3, giving a spurious-free dynamic range of 89 dB in 1 MHz resolution bandwidth

Discrete-Time Mixing Receiver Architecture for RF-Sampling Software-Defined Radio

A discrete-time (DT) mixing architecture for RF-sampling receivers is presented. This architecture makes RF sampling more suitable for software-defined radio (SDR) as it achieves wideband quadrature demodulation and wideband harmonic rejection. The paper consists of two parts. In the first part, different downconversion techniques are classified and compared, leading to the definition of a DT mixing concept. The suitability of CT-mixing and RF-sampling receivers to SDR is also discussed. In the second part, we elaborate the DT-mixing architecture, which can be realized by de-multiplexing. Simulation shows a wideband 90° phase shift between I and Q outputs without systematic channel bandwidth limitation. Oversampling and harmonic rejection relaxes RF pre-filtering and reduces noise and interference folding. A proof-of-concept DT-mixing downconverter has been built in 65 nm CMOS, for 0.2 to 0.9 GHz RF band employing 8-times oversampling. It can reject 2nd to 6th harmonics by 40 dB typically and without systematic channel bandwidth limitation. Without an LNA, it achieves a gain of -0.5 to 2.5 dB, a DSB noise figure of 18 to 20 dB, an IIP3 = +10 dBm, and an IIP2 = +53 dBm, while consuming less than 19 mW including multiphase clock generation

Digitally-Enhanced Software-Defined Radio Receiver Robust to Out-of-Band Interference

A software-defined radio (SDR) receiver with improved robustness to out-of-band interference (OBI) is presented. Two main challenges are identified for an OBI-robust SDR receiver: out-of-band nonlinearity and harmonic mixing. Voltage gain at RF is avoided, and instead realized at baseband in combination with low-pass filtering to mitigate blockers and improve out-of-band IIP3. Two alternative “iterative” harmonic-rejection (HR) techniques are presented to achieve high HR robust to mismatch: a) an analog two-stage polyphase HR concept, which enhances the HR to more than 60 dB; b) a digital adaptive interference cancelling (AIC) technique, which can suppress one dominating harmonic by at least 80 dB. An accurate multiphase clock generator is presented for a mismatch-robust HR. A proof-of-concept receiver is implemented in 65 nm CMOS. Measurements show 34 dB gain, 4 dB NF, and 3.5 dBm in-band IIP3 while the out-of-band IIP3 is + 16 dBm without fine tuning. The measured RF bandwidth is up to 6 GHz and the 8-phase LO works up to 0.9 GHz (master clock up to 7.2 GHz). At 0.8 GHz LO, the analog two-stage polyphase HR achieves a second to sixth order HR > dB over 40 chips, while the digital AIC technique achieves HR > 80 dB for the dominating harmonic. The total power consumption is 50 mA from a 1.2 V supply

A 0.8 V T Network-Based 2.6 GHz Downconverter RFIC

A 2.6 GHz downconverter RFIC is designed and implemented using a 0.18 μm CMOS standard process. An important goal of the design is to achieve the high linearity that is required in WiMAX systems with a low supply voltage. A passive T phase-shift network is used as an RF input stage in a Gilbert cell to reduce supply voltage. A single supply voltage of 0.8 V is used with a power consumption of 5.87 mW. The T network-based downconverter achieves a conversion gain (CG) of 5 dB, a single-sideband noise figure (NF) of 16.16 dB, an RF-to-IF isolation of greater than 20 dB, and an input-referred third-order intercept point (IIP3) of 1 dBm when the LO power of -13 dBm is applied

Quadrature LC VCO with passive coupling and phase combining network

A circuit and method for generating a signal is disclosed. The circuit includes a set of wide tuning LC tanks, a set of core transistors cross coupled to the set of wide tuning LC tanks, and a combining network coupled to the set of wide tuning LC tanks and the set of core transistors. The combining network further includes a set of inputs connected to the set of wide tuning LC tanks and the set of core transistors, a set of coupling transistors connected to the set of inputs, a set of source inductors connected to the set of coupling transistors, a coupling capacitor connected to the set of source inductors, a load resistor connected to the coupling capacitor. The combining network combines the set of inputs and the signal is delivered to the load resistor as a fourth order harmonic.Board of Regents, University of Texas Syste

Recursive receiver down-converters with multiband feedback and gain-reuse for low-power applications

Power minimization in wireless transceivers has become increasingly critical in recent years with the emergence of standards for short-distance applications in the 900 MHz and 2.4 GHz industrial, scientific and medical (ISM) radio bands. The demand for long battery life and better portability in such applications has led to extensive research on low power radio architectures. This dissertation introduces receiver topologies for low-power systems and presents a theoretical performance analysis of the topologies. Two fully integrated receiver down-converters that demonstrate the concept are implemented in a 0.13-[mu]m CMOS technology. These topologies employ merged mixers and IF amplifiers in order to reduce power dissipation for a given dynamic range performance. In the described topologies, the input stage of a mixer is used to simultaneously provide conversion gain and baseband amplification. This is achieved by applying the down-converted IF signal to input of the mixer. Consequently, the effective conversion gain of the design is greatly enhanced with current requirement primarily determined by the input transconductor. Potential degradation mechanisms related to instability and second-order distortion are identified and solved by the use of appropriate circuit techniques. Noise and linearity performance of the down-converters is analyzed and compared to that of conventional cascaded design counterparts. The potential for enhancement of IIP3 performance through cancellation of nonlinear products is discussed. Potential extensions of the above work including feedback-based architectures that exploit multiple loops for further maximizing the power efficiency of receiver front-ends are also presented.Electrical and Computer Engineerin

A Novel 2.4GHz CMOS Up-Conversion Current-Mode Mixer

In this paper, a low-power up-conversion current-mode mixer, designed in the chartered 0.18-μm RFCMOS technology, is proposed to realize the transmitter front-end in the frequency band of 2.4 GHz. The proposed mixer can convert a 10 MHz intermediate frequency (IF) signal to a 2.4 GHz RF signal, with a local oscillator power of 2 dBm at 2.39 GHz. A comparison with conventional voltage-mode up-conversion mixer shows that this mixer has advantages of low voltage, low power consumption and high performance. Simulation results demonstrate that at 2.4 GHz, the circuit provides 6.5 dB of conversion gain and the input-referred third-order intercept point (IIP3) of 15.3 dBm, while drawing only 5.7 mA from a 1.2V supply voltage. The chip area is only 0.7 mm x 0.8 mm

Equalization of Third-Order Intermodulation Products in Wideband Direct Conversion Receivers

This paper reports a SAW-less direct-conversion receiver which utilizes a mixed-signal feedforward path to regenerate and adaptively cancel IM3 products, thus accomplishing system-level linearization. The receiver system performance is dominated by a custom integrated RF front end implemented in 130-nm CMOS and achieves an uncorrected out-of-band IIP3 of -7.1 dBm under the worst-case UMTS FDD Region 1 blocking specifications. Under IM3 equalization, the receiver achieves an effective IIP3 of +5.3 dBm and meets the UMTS BER sensitivity requirement with 3.7 dB of margin

A low-voltage RF-CMOS receiver front-end for a wireless fall detection microsystem

Dissertação para obtenção do Grau de Mestre em Engenharia Eletrotécnica e de Computadores, pela Universidade Nova de Ciências e TecnologiaIn this thesis a Low Noise Amplifier-Mixer, the LM, is presented. In the Low Noise Amplifier a common-gate, a common-source and a buffer were used and the last one with the target to work in single-end configuration. A typical structure common-gate was used in the Mixer. The development of this structure had as goal, the implementation of a circuit capable to be used in a fall detection system for disable patients, monitoring the state and behavior remotely by an hospital. The conception of this circuit did not have only the objective, the prevention of falls, but also the contribute for the Medicine enrichment, as well as the research in several institutions. It was developed to cover ISM and WMTS frequency bands since 400 to 900MHz and to operate at low voltage in a range values between 0.6 and 1.2 V. The system was totally implemented with MOSFETs without reactive elements using the UMC CMOS 130 nm technology. Some techniques are used in design and optimizing with the target of low voltage and low consumption. The circuit present a total consumption of 11.5 mW extracted from a supply voltage of 1.2 V and a consumption of 3.5 mW extracted from a supply voltage of 0.6 V