Low-voltage, low-power circuits for data communication systems

There are growing industrial demands for low-voltage supply and low-power consumption circuits and systems. This is especially true for very high integration level and very large scale integrated (VLSI) mixed-signal chips and system-on-a-chip. It is mainly due to the limited power dissipation within a small area and the costs related to the packaging and thermal management. In this research work, two low-voltage, low-power integrated circuits used for data communication systems are introduced. The first one is a high performance continuous-time linear phase filter with automatic frequency tuning. The filter can be used in hard disk driver systems and wired communication systems such as 1000Base-T transceivers. A pseudo-differential operational transconductance amplifier (OTA) based on transistors operating in triode region is used to achieve a large linear signal swing with low-voltage supplies. A common-mode (CM) control circuit that combines common-mode feedback (CMFB), common-mode feedforward (CMFF), and adaptive-bias has been proposed. With a 2.3V single supply, the filters total harmonic distortion is less than 44dB for a 2VPP differential input, which is due to the well controlled CM behavior. The ratio of the root mean square value of the ac signal to the power supply voltage is around 31%, which is much better than previous realizations. The second integrated circuit includes two LVDS drivers used for high-speed point-to-point links. By removing the stacked switches used in the conventional structures, both LVDS drivers can operate with ultra low-voltage supplies. Although the Double Current Sources (DCS) LVDS driver draws twice minimum static current as required by the signal swing, it is quite simple and achieves very high speed operation. The Switchable Current Sources (SCS) LVDS driver, by dynamically switching the current sources, draws minimum static current and reduces the power consumption by 60% compared to the previously reported LVDS drivers. Both LVDS drivers are compliant to the standards and operate at data rates up to gigabits-per-second

High performance RF and baseband building blocks for wireless receivers

Because of the unique architecture of wireless receivers, a designer must understand both the high frequency aspects as well as the low-frequency analog considerations for different building blocks of the receiver. The primary goal of this research work is to explore techniques for implementing high performance RF and baseband building blocks for wireless applications. Several novel techniques to improve the performance of analog building blocks are presented. An enhanced technique to couple two LC resonators is presented which does not degrade the loaded quality factor of the resonators which results in an increased dynamic range. A novel technique to automatically tune the quality factor of LC resonators is presented. The proposed scheme is stable and fast and allows programming both the quality factor and amplitude response of the LC filter. To keep the oscillation amplitude of LC VCOs constant and thus achieving a minimum phase noise and a reliable startup, a stable amplitude control loop is presented. The proposed scheme has been also used in a master-slave quality factor tuning of LC filters. An efficient and low-cost architecture for a 3.1GHz-10.6GHz ultra-wide band frequency synthesizer is presented. The proposed scheme is capable of generating 14A novel pseudo-differential transconductance amplifier is presented. The proposed scheme takes advantage of the second-order harmonic available at the output current of pseudo-differential structure to cancel the third-order harmonic distortion. A novel nonlinear function is proposed which inherently removes the third and the fifth order harmonics at its output signal. The proposed nonlinear block is used in a bandpass-based oscillator to generate a highly linear sinusoidal output. Finally, a linearized BiCMOS transconductance amplifier is presented. This transconductance is used to build a third-order linear phase low pass filter with a cut-off frequency of 264MHz for an ultra-wide band receiver. carrier frequencies

Low power architecture and circuit techniques for high boost wideband Gm-C filters

With the current trend towards integration and higher data rates, read channel design needs to incorporate significant boost for a wider signal bandwidth. This dissertation explores the analog design problems associated with design of such 'Equalizing Filter' (boost filter) for read channel applications. Specifically, a 330MHz, 5th order Gm-C continuous time lowpass filter with 24dB boost is designed. Existing architectures are found to be unsuitable for low power, wideband and high boost operation. The proposed solution realizes boosting zeros by efficiently combining available transfer functions associated with all nodes of cascaded biquad cells. Further, circuit techniques suitable for high frequency filter design are elaborated such as: application of the Gilbert cell as a variable transconductor and a new Common-Mode-Feedback (CMFB) error amplifier that improves common mode accuracy without compromising on bandwidth or circuit complexity. A prototype is fabricated in a standard 0.35mm CMOS process. Experimental results show -41dB of IM3 for 250mV peak to peak swing with 8.6mW/pole of power dissipation

Continuous-time low-pass filters for integrated wideband radio receivers

This thesis concentrates on the design and implementation of analog baseband continuous-time low-pass filters for integrated wideband radio receivers. A total of five experimental analog baseband low-pass filter circuits were designed and implemented as a part of five single-chip radio receivers in this work. After the motivation for the research work presented in this thesis has been introduced, an overview of analog baseband filters in radio receivers is given first. In addition, a review of the three receiver architectures and the three wireless applications that are adopted in the experimental work of this thesis is presented. The relationship between the integrator non-idealities and integrator Q-factor, as well as the effect of the integrator Q-factor on the filter frequency response, are thoroughly studied on the basis of a literature review. The theoretical study that is provided is essential for the gm-C filter synthesis with non-ideal lossy integrators that is presented after the introduction of different techniques to realize integrator-based continuous-time low-pass filters. The filter design approach proposed for gm-C filters is original work and one of the main points in this thesis, in addition to the experimental IC implementations. Two evolution versions of fourth-order 10-MHz opamp-RC low-pass filters designed and implemented for two multicarrier WCDMA base-station receivers in a 0.25-µm SiGe BiCMOS technology are presented, along with the experimental results of both the low-pass filters and the corresponding radio receivers. The circuit techniques that were used in the three gm-C filter implementations of this work are described and a common-mode induced even-order distortion in a pseudo-differential filter is analyzed. Two evolution versions of fifth-order 240-MHz gm-C low-pass filters that were designed and implemented for two single-chip WiMedia UWB direct-conversion receivers in a standard 0.13-µm and 65-nm CMOS technology, respectively, are presented, along with the experimental results of both the low-pass filters and the second receiver version. The second UWB filter design was also embedded with an ADC into the baseband of a 60-GHz 65-nm CMOS radio receiver. In addition, a third-order 1-GHz gm-C low-pass filter was designed, rather as a test structure, for the same receiver. The experimental results of the receiver and the third gm-C filter implementation are presented

A wide dynamic range high-q high-frequency bandpass filter with an automatic quality factor tuning scheme

An 80 MHz bandpass filter with a tunable quality factor of 16∼44 using an improved transconductor circuit is presented. A noise optimized biquad structure for high-Q, high- frequency bandpass filter is proposed. The quality factor of the filter is tuned using a new quality factor locked loop algorithm. It was shown that a second-order quality factor locked loop is necessary and sufficient to tune the quality factor of a bandpass filter with zero steady state error. The accuracy, mismatch, and sensitivty analysis of the new tuning scheme was performed and analyzed. Based on the proposed noise optimized filter structure and new quality factor tuning scheme, a biquad filter was designed and fabricated in 0.25 μm BiCMOS process. The measured results show that the biquad filter achieves a SNR of 45 dB at IMD of 40 dB. The P-1dB compression point and IIP3 of the filter are -10 dBm and -2.68 dBm, respectively. The proposed biquad filter and quality factor tuning scheme consumes 58mW and 13 mW of power at 3.3 V supply.Ph.D.Committee Chair: Allen Phillip; Committee Member: Hasler Paul; Committee Member: Keezer David; Committee Member: Kenny James; Committee Member: Pan Ronghu

Automatic tuning of continuous-time filters

Integrated high-Q continuous-time filters require adaptive tuning circuits that will correct the filter parameters such as center frequency and quality factor (Q). Three different automatic tuning techniques are introduced. In all of the proposed methods, frequencyand quality factor tuning loops are controlled digitally, providing stable tuning by activating only one loop at a given time. In addition, a direct relationship between passband gain and quality factor is not required, so the techniques can be applied to active LC filters as well as Gm-C filters. The digital-tuning method based on phase comparison was verified with 1% tuning accuracy at 5.5 MHz for Q of 20. It uses phase information for both Q and center-frequency tuning. The filter output phase is tuned to the known references, which are generated by a frequency synthesizer. The core tuning circuit consists of D flip-flops (DFF) and simple logic gates. DFFs are utilized to perform binary phase comparisons. The second method, high-order digital tuning based on phase comparison, is an extension of the previous technique to high-order analog filters without depending on the master-slave approach. Direct tuning of the overall filter response is achieved without separating individual biquad sections, eliminating switches and their parasitics. The tuning system was verified with a prototype 6th order bandpass filter at 19 MHz with 0.6 MHz bandwidth, which was fabricated in a conventional 0.5 [mu]m CMOS technology. Analysis of different practical limitations is also provided. Finally, the digital-tuning method based on magnitude comparison is proposed for second-order filters for higher frequency operations. It incorporates a frequency synthesizer to generate reference signals, an envelope detector and a switched comparator to compare output magnitudes at three reference frequencies. The theoretical analysis of the technique and the simulation results are provided

High performance continuous-time filters for information transfer systems

Vast attention has been paid to active continuous-time filters over the years. Thus as the cheap, readily available integrated circuit OpAmps replaced their discrete circuit versions, it became feasible to consider active-RC filter circuits using large numbers of OpAmps. Similarly the development of integrated operational transconductance amplifier (OTA) led to new filter configurations. This gave rise to OTA-C filters, using only active devices and capacitors, making it more suitable for integration. The demands on filter circuits have become ever more stringent as the world of electronics and communications has advanced. In addition, the continuing increase in the operating frequencies of modern circuits and systems increases the need for active filters that can perform at these higher frequencies; an area where the LC active filter emerges. What mainly limits the performance of an analog circuit are the non-idealities of the used building blocks and the circuit architecture. This research concentrates on the design issues of high frequency continuous-time integrated filters. Several novel circuit building blocks are introduced. A novel pseudo-differential fully balanced fully symmetric CMOS OTA architecture with inherent common-mode detection is proposed. Through judicious arrangement, the common-mode feedback circuit can be economically implemented. On the level of system architectures, a novel filter low-voltage 4th order RF bandpass filter structure based on emulation of two magnetically coupled resonators is presented. A unique feature of the proposed architecture is using electric coupling to emulate the effect of the coupled-inductors, thus providing bandwidth tuning with small passband ripple. As part of a direct conversion dual-mode 802.11b/Bluetooth receiver, a BiCMOS 5th order low-pass channel selection filter is designed. The filter operated from a single 2.5V supply and achieves a 76dB of out-of-band SFDR. A digital automatic tuning system is also implemented to account for process and temperature variations. As part of a Bluetooth transmitter, a low-power quadrature direct digital frequency synthesizer (DDFS) is presented. Piecewise linear approximation is used to avoid using a ROM look-up table to store the sine values in a conventional DDFS. Significant saving in power consumption, due to the elimination of the ROM, renders the design more suitable for portable wireless communication applications

Tunable Filters and RF MEMS Variable Capacitors with Closed Loop Control

Multi-band and multi-mode radios are becoming prevalent and necessary in order to provide optimal data rates across a network with a diverse and spotty landscape of coverage areas (3G, HSPA, LTE, etc.). As the number of required bands and modes increases, the aggregate cost of discrete RF signal chains justi es the adoption of tunable solutions. Tunable fi lters are one of the pieces crucial to signal chain amalgamation. The main requirements for a tunable fi lter are high unloaded quality factor, wide tuning range, high tuning speed, high linearity, and small size. MEMS technology is the most promising in terms of tuning range, quality factor, linearity and size. In addition, a fi lter that maintains a constant passband bandwidth as the center frequency is tuned is preferred since the analog baseband processing circuitry tends to be tailored for a particular signal bandwidth. In this work, a novel design technique for tunable fi lters with controlled and predictable bandwidth variation is presented. The design technique is presented alongside an analysis and modeling method for predicting the final filter response during design optimization. The method is based on the well known coupling matrix model. In order to demonstrate the design and modeling technique, a novel coupling structure for stripline fi lters is presented that results in substantial improvements in coupling bandwidth variation over an octave tuning range when compared to combline and interdigitated coupled line fi lters. In order for a coupled resonator filter to produce an equal ripple Chebyshev response, each resonator of the fi lter must be tuned to precisely the same resonant frequency. Production tuned fi lters are routinely tuned in the lab and production environments by skilled technicians in order to compensate for manufacturing tolerances. However, integrated tunable filters cannot be tuned by traditional means since they are integrated into systems on circuit boards or inside front end modules. A fixed tuning table for all manufactured modules is inadequate since the required tuning accuracy exceeds the tolerance of the tuning elements. In this work, we develop tuning techniques for the automatic in-circuit tuning of tunable filters using scalar transmission measurement. The scalar transmission based techniques obviate the use of directional couplers. Techniques based on both swept and single frequency scalar transmission measurement are developed. The swept frequency technique, based on the Hilbert transform derived relative groupdelay, tunes both couplings and resonant frequencies while the single frequency technique only tunes the center frequency. High performance filters necessitate high resonator quality factors. Although fi lters are traditionally treated as passive devices, tunable fi lters need to be treated as active devices. Tuning elements invariably introduce non-linearities that limit the useful power handling of the tunable fi lter. RF MEMS devices have been a topic of intense research for many years for their promising characteristics of high quality factor and high power handling. Control and reliability issues have resulted in a shift from continuously tunable devices to discretely switched devices. However, fi lter tuning applications require fine resolution and therefore many bits for digital capacitor banks. An analog/digital hybrid tuning approach would enable the tuning range of a switched capacitor bank to be combined with the tuning resolution of an analog tunable capacitor. In this work, a device-level position control mechanism is proposed for piezoresistive feedback of device capacitance over the device's tuning range. It is shown that piezoresistve position control is ef ective at improving capacitance uncertainty in a CMOS integrated RF MEMS variable capacitor

LINC based amplifier architectures for power efficient wireless transmitters

Wireless communication trends Performance measuring of a communication system Power amplifiers and transmitters Power efficiency enhancement techniques Design and Optimization of LINC transmitter for OFDM applications LINC concept LINC signal decomposition LINC efficiency and combiner technologies Design optimization of LINC system Mismatch (imbalance) effects Advanced LINC transmitter architectures The 2X1 LINC transmitter system The 2X2 LINC transmitter system Mismatch effects