Frequency Synchronization in Frequency Domain OFDM-IM based WLAN Systems

The next-generation of wireless local area network systems are being conceptualized with new applications, smart devices and use cases which mandate unprecedented levels of high data rates, spectral efficiency, reliability, low latency and high energy efficiency. The index modulated orthogonal frequency division multiplexing (OFDM-IM) stands out as the most endearing candidate for physical layer modulation technique which provides a smooth transit to green communications. However, OFDM-IM being a multicarrier technique similar to classical OFDM is also very sensitive to frequency synchronization errors and needs to be addressed on priority. In this article, a novel algorithm is proposed which estimates and corrects the carrier frequency offset at the receiver and the algorithm\u27s performance is compared with two frequency domain variants of OFDM-IM and the classical OFDM under the same channel conditions and the simulation results show that our algorithm is not only capable of meeting the standard requirement of +/-20ppm but can handle higher offsets till +/-30ppm

Ray-tracing-based numerical assessment of the spatiotemporal duty cycle of 5G massive MIMO in an outdoor urban environment

Featured Application The presented numerical approach can be directly applied to the estimation of the compliance boundary of the antenna array base stations and the downlink human EMF exposure assessment in the networks served by such base stations. In the near future, wireless coverage will be provided by the base stations equipped with dynamically-controlled massive phased antenna arrays that direct the transmission towards the user. This contribution describes a computational method to estimate realistic maximum power levels produced by such base stations, in terms of the time-averaged normalized antenna array gain. The Ray-Tracing method is used to simulate the electromagnetic field (EMF) propagation in an urban outdoor macro-cell environment model. The model geometry entities are generated stochastically, which allowed generalization of the results through statistical analysis. Multiple modes of the base station operation are compared: from LTE multi-user codebook beamforming to the more advanced Maximum Ratio and Zero-Forcing precoding schemes foreseen to be implemented in the massive Multiple-Input Multiple-Output (MIMO) communication protocols. The influence of the antenna array size, from 4 up to 100 elements, in a square planar arrangement is studied. For a 64-element array, the 95th percentile of the maximum time-averaged array gain amounts to around 20% of the theoretical maximum, using the Maximum Ratio precoding with 5 simultaneously connected users, assuming a 10 s connection duration per user. Connection between the average array gain and actual EMF levels in the environment is drawn and its implications on the human exposure in the next generation networks are discussed

Visible Light Communications for Industrial Applications—Challenges and Potentials

Visible Light Communication (VLC) is a short-range optical wireless communication technology that has been gaining attention due to its potential to offload heavy data traffic from the congested radio wireless spectrum. At the same time, wireless communications are becoming crucial to smart manufacturing within the scope of Industry 4.0. Industry 4.0 is a developing trend of high-speed data exchange in automation for manufacturing technologies and is referred to as the fourth industrial revolution. This trend requires fast, reliable, low-latency, and cost-effective data transmissions with fast synchronizations to ensure smooth operations for various processes. VLC is capable of providing reliable, low-latency, and secure connections that do not penetrate walls and is immune to electromagnetic interference. As such, this paper aims to show the potential of VLC for industrial wireless applications by examining the latest research work in VLC systems. This work also highlights and classifies challenges that might arise with the applicability of VLC and visible light positioning (VLP) systems in these settings. Given the previous work performed in these areas, and the major ongoing experimental projects looking into the use of VLC systems for industrial applications, the use of VLC and VLP systems for industrial applications shows promising potential

Deep Learning Based Secure MIMO Communications with Imperfect CSI for Heterogeneous Networks

Perfect channel state information (CSI) is required in most of the classical physical layer security techniques, while it is difficult to obtain the ideal CSI due to the time varying wireless fading channel. Although imperfect CSI has a greatly impact on the security of MIMO communications, deep learning is becoming a promising solution to handle the negative effect of imperfect CSI. In this work, we propose two types of deep learning based secure MIMO detectors for heterogeneous networks, where the macro base station (BS) chooses the null-space eigenvectors to prevent information leakage to the femto BS. Thus, the bit error rate of the associated user is adopted as the metric to valuate the system performance. With the help of deep convolutional neural networks (CNNs), the macro BS obtains the refined version from the imperfect CSI. Simulation results are provided to validate the proposed algorithms. The impacts of system parameters, such as the correlation factor of imperfect CSI, the normalized doppler frequency, the number of antennas are investigated in different setup scenarios. The results show that considerable performance gains can be obtained from the deep learning based detectors compared with the classical maximum likelihood algorithm

Radio resource allocation for overlay D2D-based vehicular communications in future wireless networks

Mobilfunknetze der nächsten Generation ermöglichen einen weitverbreiteten Einsatz von Device-to-Device Kommunikation, der direkten Kommunikation zwischen zellularen Endgeräten. Für viele Anwendungsfälle zur direkten Kommunikation zwischen Endgeräten sind eine deterministische Latenz und die hohe Zuverlässigkeit von zentraler Bedeutung. Dienste zur direkten Kommunikation (D2D) für in der Nähe befindliche Endgeräte sind vielversprechend die hohen Anforderungen an Latenz und Zuverlässigkeit für zukünftige vertikale Anwendungen zu erfüllen. Eine der herausragenden vertikalen Anwendungen ist die Fahrzeugkommunikation, bei der die Fahrzeuge sicherheitskritische Meldungen direkt über D2D-Kommunikation austauschen, die dadurch zur Reduktion von Verkehrsunfällen und gleichzeitig von Todesfällen im Straßenverkehrt beiträgt. Neue Techniken zur effizienteren Zuweisung von Funkressourcen in der D2D-Kommunikation haben in letzter Zeit in Industrie und Wissenschaft große Aufmerksamkeit erlangt. Zusätzlich zur Allokation von Ressourcen, wird die Energieeffizienz zunehmend wichtiger, die normalerweise im Zusammenhang mit der Ressourcenallokation behandelt wird. Diese Dissertation untersucht verschiedener Ansätze der Funkressourcenzuweisung und Energieeffizienztechniken in der LTE und NR V2X Kommunikation. Im Folgenden beschreiben wir kurz die Kernideen der Dissertation. Meist zeichnen sich D2D-Anwendungen durch ein relativ geringes Datenvolumen aus, die über Funkressourcen übertragen werden. In LTE können diese Funkressourcen aufgrund der groben Granularität für die Ressourcenzuweisung nicht effizient genutzt werden. Insbesondere beim semi-persistenten Scheduling, bei dem eine Funkressource über einen längeren Zeitraum im Overlay D2D festgelegt wird, sind die Funkressourcen für solche Anwendungen nicht ausgelastet. Um dieses Problem zu lösen, wird eine hierarchische Form für das Management der Funkressourcen, ein sogenanntes Subgranting-Schema, vorgeschlagen. Dabei kann ein nahegelegener zellularer Nutzer, der sogenannte begünstigte Nutzer, ungenutzten Funkressourcen, die durch Subgranting-Signalisierung angezeigt werden, wiederzuverwenden. Das vorgeschlagene Schema wird bewertet und mit "shortening TTI", einen Schema mit reduzierten Sendezeitintervallen, in Bezug auf den Zellendurchsatz verglichen. Als nächster Schritt wird untersucht, wie der begünstigten Benutzer ausgewählt werden kann und als Maximierungsproblem des Zellendurchsatzes im Uplink unter Berücksichtigung von Zuverlässigkeits- und Latenzanforderungen dargestellt. Dafür wird ein heuristischer zentralisierter, d.h. dedizierter Sub-Granting-Radio-Ressource DSGRR-Algorithmus vorgeschlagen. Die Simulationsergebnisse und die Analyse ergeben in einem Szenario mit stationären Nutzern eine Erhöhung des Zelldurchsatzes bei dem Einsatz des vorgeschlagenen DSGRR-Algorithmus im Vergleich zu einer zufälligen Auswahl von Nutzern. Zusätzlich wird das Problem der Auswahl des begünstigten Nutzers in einem dynamischen Szenario untersucht, in dem sich alle Nutzer bewegen. Wir bewerten den durch das Sub-Granting durch die Mobilität entstandenen Signalisierungs-Overhead im DSGRR. Anschließend wird ein verteilter Heuristik-Algorithmus (OSGRR) vorgeschlagen und sowohl mit den Ergebnissen des DSGRR-Algorithmus als auch mit den Ergebnissen ohne Sub-Granting verglichen. Die Simulationsergebnisse zeigen einen verbesserten Zellendurchsatz für den OSGRR im Vergleich zu den anderen Algorithmen. Außerdem ist zu beobachten, dass der durch den OSGRR entstehende Overhead geringer ist als der durch den DSGRR, während der erreichte Zellendurchsatz nahe am maximal erreichbaren Uplink-Zellendurchsatz liegt. Zusätzlich wird die Ressourcenallokation im Zusammenhang mit der Energieeffizienz bei autonomer Ressourcenauswahl in New Radio (NR) Mode 2 untersucht. Die autonome Auswahl der Ressourcen wird als Verhältnis von Summenrate und Energieverbrauch formuliert. Das Ziel ist den Stromverbrauch der akkubetriebenen Endgeräte unter Berücksichtigung der geforderten Zuverlässigkeit und Latenz zu minimieren. Der heuristische Algorithmus "Density of Traffic-based Resource Allocation (DeTRA)" wird als Lösung vorgeschlagen. Bei dem vorgeschlagenen Algorithmus wird der Ressourcenpool in Abhängigkeit von der Verkehrsdichte pro Verkehrsart aufgeteilt. Die zufällige Auswahl erfolgt zwingend auf dem dedizierten Ressourcenpool beim Eintreffen aperiodischer Daten. Die Simulationsergebnisse zeigen, dass der vorgeschlagene Algorithmus die gleichen Ergebnisse für die Paketempfangsrate (PRR) erreicht, wie der sensing-basierte Algorithmus. Zusätzlich wird der Stromverbrauch des Endgeräts reduziert und damit die Energieeffizienz durch die Anwendung des DeTRA-Algorithmus verbessert. In dieser Arbeit werden Techniken zur Allokation von Funkressourcen in der LTE-basierten D2D-Kommunikation erforscht und eingesetzt, mit dem Ziel Funkressourcen effizienter zu nutzen. Darüber hinaus ist der in dieser Arbeit vorgestellte Ansatz eine Basis für zukünftige Untersuchungen, wie akkubasierte Endgeräte mit minimalem Stromverbrauch in der NR-V2X-Kommunikation Funkressourcen optimal auswählen können.Next-generation cellular networks are envisioned to enable widely Device-to-Device (D2D) communication. For many applications in the D2D domain, deterministic communication latency and high reliability are of exceptionally high importance. The proximity service provided by D2D communication is a promising feature that can fulfil the reliability and latency requirements of emerging vertical applications. One of the prominent vertical applications is vehicular communication, in which the vehicles disseminate safety messages directly through D2D communication, resulting in the fatality rate reduction due to a possible collision. Radio resource allocation techniques in D2D communication have recently gained much attention in industry and academia, through which valuable radio resources are allocated more efficiently. In addition to the resource allocation techniques, energy sustainability is highly important and is usually considered in conjunction with the resource allocation approach. This dissertation is dedicated to studying different avenues of the radio resource allocation and energy efficiency techniques in Long Term Evolution (LTE) and New Radio (NR) Vehicle-to-Everythings (V2X) communications. In the following, we briefly describe the core ideas in this study. Mostly, the D2D applications are characterized by relatively small traffic payload size, and in LTE, due to coarse granularity of the subframe, the radio resources can not be utilized efficiently. Particularly, in the case of semi-persistent scheduling when a radio resource is scheduled for a longer time in the overlay D2D, the radio resources are underutilized for such applications. To address this problem, a hierarchical radio resource management scheme, i.e., a sub-granting scheme, is proposed by which nearby cellular users, i.e., beneficiary users, are allowed to reuse the unused radio resource indicated by sub-granting signaling. The proposed scheme is evaluated and compared with shortening Transmission Time Interval (TTI) schemes in terms of cell throughput. Then, the beneficiary user selection problem is investigated and is cast as a maximization problem of uplink cell throughput subject to reliability and latency requirements. A heuristic centralized, i.e., dedicated sub-granting radio resource Dedicated Sub-Granting Radio Resource (DSGRR) algorithm is proposed to address the original beneficiary user selection problem. The simulation results and analysis show the superiority of the proposed DSGRR algorithm over the random beneficiary user selection algorithm in terms of the cell throughput in a scenario with stationary users. Further, the beneficiary user selection problem is investigated in a scenario where all users are moving in a dynamic environment. We evaluate the sub-granting signaling overhead due to mobility in the DSGRR, and then a distributed heuristics algorithm, i.e., Open Sub-Granting Radio Resource (OSGRR), is proposed and compared with the DSGRR algorithm and no sub-granting case. Simulation results show improved cell throughput for the OSGRR compared with other algorithms. Besides, it is observed that the overhead incurred by the OSGRR is less than the DSGRR while the achieved cell throughput is yet close to the maximum achievable uplink cell throughput. Also, joint resource allocation and energy efficiency in autonomous resource selection in NR, i.e. Mode 2, is examined. The autonomous resource selection is formulated as a ratio of sum-rate and energy consumption. The objective is to minimize the energy efficiency of the power-saving users subject to reliability and latency requirements. A heuristic algorithm, density of traffic-based resource allocation (DeTRA), is proposed to solve the problem. The proposed algorithm splits the resource pool based on the traffic density per traffic type. The random selection is then mandated to be performed on the dedicated resource pool upon arrival of the aperiodic traffic is triggered. The simulation results show that the proposed algorithm achieves the same packet reception ratio (PRR) value as the sensing-based algorithm. In addition, per-user power consumption is reduced, and consequently, the energy efficiency is improved by applying the DeTRA algorithm. The research in this study leverages radio resource allocation techniques in LTE based D2D communications to be utilized radio resources more efficiently. In addition, the conducted research paves a way to study further how the power-saving users would optimally select the radio resources with minimum energy consumption in NR V2X communications

Towards the Digital Twin (DT) of narrow-band Internet of Things (NBIoT) wireless communication in industrial indoor environment

A study of the behavior of NB-IoT wireless communication in an industrial indoor environment was conducted in this paper. With Wireless Insite software, a scenario in the industrial sector was simulated and modeled. Our research examined how this scenario or environment affected the communication parameters of NB-IoT’s physical layer. In this context, throughput levels among terminals as well as between terminals and transceiver towers, the power received at signal destination points, signal-to-noise ratios (SNRs) in the environment, and distances between terminals and transceivers are considered. These simulated results are also compared with the calculated or theoretical values of these parameters. The results show the effect of the industrial setting on wireless communication. The differences between the theoretical and simulated values are also established

Robust, Resilient Networked Communication in Challenged Environments

In challenged environments, digital communication infrastructure may be difficult or even impossible to access. This is especially true in rural and developing regions, as well as in any region during a time of political or environmental crisis. We advance the state of the art in wireless networking and security to design networks and applications that rapidly assess changing networking conditions to restore communication and provide local situational awareness. This dissertation examines new systems for responding to current and emerging needs for wireless networks. This work looks across the wireless ecosystem of widely deployed standards. We develop new tools to improve network assessment and to provide robust and reliable network communication. By incorporating new technological breakthroughs, such as the wide commercial success of Unmanned Aircraft Systems (UAS), we introduce novel methods and systems for existing wireless standards for these challenged networks. We assess how existing technologies and standards function in difficult environments: lacking end-end Internet connectivity, experiencing overload or other resource constraints, and operating in three dimensional space. Through this lens, we demonstrate how to optimize networks to serve marginalized communities outside of first world urban cities and make our networks resilient to natural and political crisis that threaten communication

Towards environmental RF-EMF assessment of mmwave high-node density complex heterogeneous environments

The densification of multiple wireless communication systems that coexist nowadays, as well as the 5G new generation cellular systems advent towards the millimeter wave (mmWave) frequency range, give rise to complex context-aware scenarios with high-node density heterogeneous networks. In this work, a radiofrequency electromagnetic field (RF-EMF) exposure assessment from an empirical and modeling approach for a large, complex indoor setting with high node density and traffic is presented. For that purpose, an intensive and comprehensive in-depth RF-EMF E-field characterization study is provided in a public library study case, considering dense personal mobile communications (5G FR2 @28 GHz) and wireless 802.11ay (@60 GHz) data access services on the mmWave frequency range. By means of an enhanced in-house deterministic 3D ray launching (3D-RL) simulation tool for RF-EMF exposure assessment, different complex heterogenous scenarios of high complexity are assessed in realistic operation conditions, considering different user distributions and densities. The use of directive antennas and MIMO beamforming techniques, as well as all the corresponding features in terms of radio wave propagation, such as the body shielding effect, dispersive material properties of obstacles, the impact of the distribution of scatterers and the associated electromagnetic propagation phenomena, are considered for simulation. Discussion regarding the contribution and impact of the coexistence of multiple heterogeneous networks and services is presented, verifying compliance with the current established international regulation limits with exposure levels far below the aforementioned limits. Finally, the proposed simulation technique is validated with a complete empirical campaign of measurements, showing good agreement. In consequence, the obtained datasets and simulation estimations, along with the proposed RF-EMF simulation tool, could be a reference approach for the design, deployment and exposure assessment of the current and future wireless communication technologies on the mmWave spectrum, where massive high-node density heterogeneous networks are expected.Project RTI2018-095499-B-C31 was funded by the Ministerio de Ciencia, Innovación y Universidades, Gobierno de España (MCIU/AEI/FEDER, UE). This project received funding from Universidad Carlos III de Madrid and the European Union's Horizon 2020 research and innovation programme under Marie Sklodowska-Curie Grant 801538

Application of evolutionary computation techniques in emerging optimization problems in 5G and beyond wireless systems

Tese (doutorado) - Universidade Federal de Santa Catarina, Centro Tecnológico, Programa de Pós-Graduação em Engenharia Elétrica, Florianópolis, 2021.Os sistemas comunicação sem fio 5G e além (B5G, do inglês Beyong 5G) permitirão a plena implantação de aplicações existentes, como carros autônomos, redes de sensores massivas e casas inteligentes. Para tornar essas aplicações possíveis, requisitos rigorosos, como alta eficiência espectral e ultra baixa latência de comunicação, devem ser atendidos. Para atender a esses requisitos, diferentes tecnologias-chave estão em desenvolvimento, como comunicações de Ondas Milimétricas (mmWave, do inglês Millimeter Wave) e Superfícies Refletivas Inteligentes (IRS, do inglês Intelligent Reflecting Surfaces). As comunicações mmWave têm atraído grande interesse devido ao abundante espectro de frequência disponível, ao contrário das bandas congestionadas adotadas nas redes 4G. No entanto, as bandas mmWave apresentam características de propagação desfavoráveis. Para superar tais problemas de propagação, o uso de beamforming altamente direcional é uma solução eficaz. Além disso, recentemente, uma tecnologia de baixo custo e alta eficiência energética denominada IRS, uma meta-superfície equipada com um grande número de elementos passivos de baixo custo, capaz de refletir o sinal incidente com uma dada mudança de fase/amplitude, foi desenvolvida para otimizar a capacidade da rede. Implantando densamente IRSs em redes de comunicação sem fio e coordenando seus elementos de maneira inteligente, os canais sem fio entre o transmissor e o receptor podem ser intencional e deterministicamente controlados para melhorar a qualidade do sinal no receptor. Embora essas tecnologias tenham inúmeros benefícios para o desempenho do sistema, elas apresentam muitos desafios em sua implantação. Mais especificamente, embora as bandas mmWave permitam considerar o uso de beamforming altamente direcional tanto na BS quanto no UE, isto pode representar um desafio para o processo de Acesso Inicial (IA, do inglês Initial Access) pois, uma vez que a transmissão omnidirecional não pode ser aplicada, devido ao seu baixo ganho de potência e SNR recebido, a duração geral do IA pode ser muito longa. O atraso causado pela busca direcional deve ser pequeno para atender a alguns dos requisitos das redes B5G como baixa latência de ponta-a-ponta. Além disso, apesar da capacidade das IRSs de controlar os canais sem fio, o projeto do beamforming na BS e na IRS é um problema desafiador devido à necessidade de estimar a informação de estado do canal (CSI, do inglês Channel State Information) de todos os links do sistema. No entanto, para estimar o CSI entre a IRS e a BS ou entre a IRS e o UE, cada elemento da IRS precisa ser equipado com uma cadeia de radiofrequência (RF, do inglês Radio Frequency), o que aumenta consideravelmente o custo e o consumo de energia do sistema e vai contra algumas das principais vantagens de utilizar IRSs em sistemas de comunicação sem fio. Portanto, motivados pelos problemas emergentes acima, nesta tese, pretendemos desenvolver novos métodos baseados em técnicas de Computação Evolutiva tais como, Algoritmos Genéticos (GA, do inglês Genetic Algorithm) e Otimização por Enxame de Partículas (PSO, do inglês Particle Swarm Optimization), visando resolver o problema de IA e realizar o projeto do beamforming na BS e IRS sem conhecimento prévio do CSI na BS. Os resultados obtidos nesta tese mostram que os métodos desenvolvidos podem reduzir consideravelmente o atraso e alcançar um desempenho próximo ao ótimo no problema de projeto do beamforming na BS e IRS com sobrecarga de treinamento reduzida.Abstract: Beyond 5G (B5G) wireless systems will enable the deployment of demanding applications such as autonomous cars, massive sensor networks, and smart homes. To make these applications possible, stringent requirements such as improved spectrum efficiency and low communication latency must be fulfilled. In order to meet these requirements, different key technologies are in development such as millimeter Wave (mmWave) communications and Intelligent Reflecting Surfaces (IRS). The mmWave communications have attracted great interest due to the abundant available spectrum, unlike the congested bands adopted in the 4G networks. However, the mmWave bands present poor propagation characteristics. To overcome these propagation issues, the use of highly directional beamforming is an effective solution. In addition, recently, an energy-efficient and low-cost technology named IRS, which is a meta-surface equipped with a large number of low-cost passive elements, capable of reflecting the incident signal with a given phase/amplitude shift, was developed to increase the network capacity. By densely deploying IRSs in wireless communication networks and intelligently coordinating their elements, the wireless channels between the transmitter and receiver can be intentionally and deterministically controlled to improve the signal quality at the receiver. Although these technologies have uncountable benefits for the system performance, they present many challenges in their deployment. More specifically, although the mmWave bands allow to consider highly directional beamforming at the BS and UE, this can be challenging for the Initial Access (IA) process. Since omnidirectional transmission may not be applied, due to its low power gain and received SNR, the overall duration of IA can be very long. The delay caused by directional search must be small to meet some of the B5G requirements for low end-to-end latency. Moreover, despite the capacity of controlling the wireless channels of the IRSs, designing the beamforming at the BS and at the IRS is a challenging problem due to the necessity of estimating the channel state information (CSI) of all system links. However, to estimate the CSI between IRS and BS or between IRS and UE, each element of the IRS needs to be equipped with one radio-frequency (RF) chain which greatly increases the cost and energy consumption of the system and goes against some of the original advantages of using an IRS. Therefore, motivated by the above emerging problems, in this thesis, we intend to develop new methods based on Evolutionary Computation techniques, i.e., Genetic Algorithms (GA) and Particle Swarm Optimization (PSO), to solve the IA problem and to design the beamforming at the BS and IRS without CSI. Results show that the developed methods can reduce the IA delay and achieve a close-to-optimal performance in the IRS beamforming problem with reduced training overhead