Outdoor to Indoor Penetration Loss at 28 GHz for Fixed Wireless Access

This paper present the results from a 28 GHz channel sounding campaign performed to investigate the effects of outdoor to indoor penetration on the wireless propagation channel characteristics for an urban microcell in a fixed wireless access scenario. The measurements are performed with a real-time channel sounder, which can measure path loss up to 169 dB, and equipped with phased array antennas that allows electrical beam steering for directionally resolved measurements in dynamic environments. Thanks to the short measurement time and the excellent phase stability of the system, we obtain both directional and omnidirectional channel power delay profiles without any delay uncertainty. For outdoor and indoor receiver locations, we compare path loss, delay spreads and angular spreads obtained for two different types of buildings

A personal, distributed exposimeter: procedure for design, calibration, validation, and application

This paper describes, for the first time, the procedure for the full design, calibration, uncertainty analysis, and practical application of a personal, distributed exposimeter (PDE) for the detection of personal exposure in the Global System for Mobile Communications (GSM) downlink (DL) band around 900 MHz (GSM 900 DL). The PDE is a sensor that consists of several body-worn antennas. The on-body location of these antennas is investigated using numerical simulations and calibration measurements in an anechoic chamber. The calibration measurements and the simulations result in a design (or on-body setup) of the PDE. This is used for validation measurements and indoor radio frequency (RF) exposure measurements in Ghent, Belgium. The main achievements of this paper are: first, the demonstration, using both measurements and simulations, that a PDE consisting of multiple on-body textile antennas will have a lower measurement uncertainty for personal RF exposure than existing on-body sensors; second, a validation of the PDE, which proves that the device correctly estimates the incident power densities; and third, a demonstration of the usability of the PDE for real exposure assessment measurements. To this aim, the validated PDE is used for indoor measurements in a residential building in Ghent, Belgium, which yield an average incident power density of 0.018 mW/m(2)

Wideband mobile propagation channels: Modelling measurements and characterisation for microcellular environments

EThOS - Electronic Theses Online ServiceGBUnited Kingdo

Doctoral Thesis: Massive MIMO in Real Propagation Environments

Mobile communications are now evolving towards the fifth generation (5G). In the near future, we expect an explosive increase in the number of connected devices, such as phones, tablets, sensors, connected vehicles and so on. Much higher data rates than in today's 4G systems are required. In the 5G visions, better coverage in remote regions is also included, aiming for bringing the current "4 billion unconnected" population into the online world. There is also a great interest in "green communications", for less energy consumption in the ICT (information and communication technology) industry. Massive MIMO is a potential technology to fulfill the requirements and visions. By equipping a base station with a large number, say tens to hundreds, of antennas, many terminals can be served in the same time-frequency resource without severe inter-user interference. Through "aggressive" spatial multiplexing, higher data rates can be achieved without increasing the required spectrum. Processing efforts can be made at the base station side, allowing terminals to have simple and cheap hardware. By exploiting the many spatial degrees of freedom, linear precoding/detection schemes can be used to achieve near-optimal performance. The large number of antennas also brings the advantage of large array gain, resulting in an increase in received signal strength. Better coverage is thus achieved. On the other hand, transmit power from base stations and terminals can be scaled down to pursue energy efficiency. In the last five years, a lot of theoretical studies have been done, showing the extraordinary advantages of massive MIMO. However, the investigations are mainly based on theoretical channels with independent and identically distributed (i.i.d.) Gaussian coefficients, and sometimes assuming unlimited number of antennas. When bringing this new technology from theory to practice, it is important to understand massive MIMO behavior in real propagation channels using practical antenna arrays. Not much has been known about real massive MIMO channels, and whether the claims about massive MIMO still hold there, until the studies in this thesis were done. The thesis study connects the "ideal" world of theory to the "non-ideal" reality. Channel measurements for massive MIMO in the 2.6 GHz band were performed, in different propagation environments and using different types of antenna arrays. Based on obtained real-life channel data, the studies include • channel characterization to identify important massive MIMO properties, • evaluation of propagation conditions in real channels and corresponding massive MIMO performance, • channel modeling for massive MIMO to capture the identified channel properties, and • reduction of massive MIMO hardware complexity through antenna selection. The investigations in the thesis conclude that massive MIMO works efficiently in real propagation environments. The theoretical advantages, as observed in i.i.d. Rayleigh channels, can also be harvested in real channels. Important propagation effects are identified for massive MIMO scenarios, including channel variations over large arrays, multipath-component (MPC) lifetime, and 3D propagation. These propagation properties are modeled and included into the COST 2100 MIMO channel model as an extension for massive MIMO. The study on antenna selection shows that characteristics in real channels allow for significant reductions of massive MIMO complexity without significant performance loss. As one of the world's first research work on massive MIMO behavior in real propagation channels, the studies in this thesis promote massive MIMO as a practical technology for future communication systems

High-Performance Integrated Window and Façade Solutions for California

The researchers developed a new generation of high-performance façade systems and supporting design and management tools to support industry in meeting California’s greenhouse gas reduction targets, reduce energy consumption, and enable an adaptable response to minimize real-time demands on the electricity grid. The project resulted in five outcomes: (1) The research team developed an R-5, 1-inch thick, triplepane, insulating glass unit with a novel low-conductance aluminum frame. This technology can help significantly reduce residential cooling and heating loads, particularly during the evening. (2) The team developed a prototype of a windowintegrated local ventilation and energy recovery device that provides clean, dry fresh air through the façade with minimal energy requirements. (3) A daylight-redirecting louver system was prototyped to redirect sunlight 15–40 feet from the window. Simulations estimated that lighting energy use could be reduced by 35–54 percent without glare. (4) A control system incorporating physics-based equations and a mathematical solver was prototyped and field tested to demonstrate feasibility. Simulations estimated that total electricity costs could be reduced by 9-28 percent on sunny summer days through adaptive control of operable shading and daylighting components and the thermostat compared to state-of-the-art automatic façade controls in commercial building perimeter zones. (5) Supporting models and tools needed by industry for technology R&D and market transformation activities were validated. Attaining California’s clean energy goals require making a fundamental shift from today’s ad-hoc assemblages of static components to turnkey, intelligent, responsive, integrated building façade systems. These systems offered significant reductions in energy use, peak demand, and operating cost in California

A Site-Specific Indoor Wireless Propagation Model

In this thesis, we explore the fundamental concepts behind the emerging field of site-specific propagation modeling for wireless communication systems. The first three chapters of background material discuss, respectively, the motivation for this study, the context of the study, and signal behavior and modeling in the predominant wireless propagation environments. A brief survey of existing ray-tracing based site-specific propagation models follows this discussion, leading naturally to the work of new model development undertaken in our thesis project. Following the detailed description of our generalized wireless channel modeling, various interference cases incorporating with this model are thoroughly discussed and results presented at the end of this thesis

Cooperative Radio Communications for Green Smart Environments

The demand for mobile connectivity is continuously increasing, and by 2020 Mobile and Wireless Communications will serve not only very dense populations of mobile phones and nomadic computers, but also the expected multiplicity of devices and sensors located in machines, vehicles, health systems and city infrastructures. Future Mobile Networks are then faced with many new scenarios and use cases, which will load the networks with different data traffic patterns, in new or shared spectrum bands, creating new specific requirements. This book addresses both the techniques to model, analyse and optimise the radio links and transmission systems in such scenarios, together with the most advanced radio access, resource management and mobile networking technologies. This text summarises the work performed by more than 500 researchers from more than 120 institutions in Europe, America and Asia, from both academia and industries, within the framework of the COST IC1004 Action on "Cooperative Radio Communications for Green and Smart Environments". The book will have appeal to graduates and researchers in the Radio Communications area, and also to engineers working in the Wireless industry. Topics discussed in this book include: • Radio waves propagation phenomena in diverse urban, indoor, vehicular and body environments• Measurements, characterization, and modelling of radio channels beyond 4G networks• Key issues in Vehicle (V2X) communication• Wireless Body Area Networks, including specific Radio Channel Models for WBANs• Energy efficiency and resource management enhancements in Radio Access Networks• Definitions and models for the virtualised and cloud RAN architectures• Advances on feasible indoor localization and tracking techniques• Recent findings and innovations in antenna systems for communications• Physical Layer Network Coding for next generation wireless systems• Methods and techniques for MIMO Over the Air (OTA) testin