172 research outputs found

    High frequency of low noise amplifier architecture for WiMAX application: A review

    Get PDF
    The low noise amplifier (LNA) circuit is exceptionally imperative as it promotes and initializes general execution performance and quality of the mobile communication system. LNA's design in radio frequency (R.F.) circuit requires the trade-off numerous imperative features' including gain, noise figure (N.F.), bandwidth, stability, sensitivity, power consumption, and complexity. Improvements to the LNA's overall performance should be made to fulfil the worldwide interoperability for microwave access (WiMAX) specifications' prerequisites. The development of front-end receiver, particularly the LNA, is genuinely pivotal for long-distance communications up to 50 km for a particular system with particular requirements. The LNA architecture has recently been designed to concentrate on a single transistor, cascode, or cascade constrained in gain, bandwidth, and noise figure

    Design of CMOS UWB LNA

    Get PDF

    Distributed Circuit Analysis and Design for Ultra-wideband Communication and sub-mm Wave Applications

    Get PDF
    This thesis explores research into new distributed circuit design techniques and topologies, developed to extend the bandwidth of amplifiers operating in the mm and sub-mm wave regimes, and in optical and visible light communication systems. Theoretical, mathematical modelling and simulation-based studies are presented, with detailed designs of new circuits based on distributed amplifier (DA) principles, and constructed using a double heterojunction bipolar transistor (DHBT) indium phosphide (InP) process with fT =fmax of 350/600 GHz. A single stage DA (SSDA) with bandwidth of 345 GHz and 8 dB gain, based on novel techniques developed in this work, shows 140% bandwidth improvement over the conventional DA design. Furthermore, the matrix-single stage DA (M-SSDA) is proposed for higher gain than both the conventional DA and matrix amplifier. A two-tier M-SSDA with 14 dB gain at 300 GHz bandwidth, and a three-tier M-SSDA with a gain of 20 dB at 324 GHz bandwidth, based on a cascode gain cell and optimized for bandwidth and gain flatness, are presented based on full foundry simulation tests. Analytical and simulation-based studies of the noise performance peculiarities of the SSDA and its multiplicative derivatives are also presented. The newly proposed circuits are fabricated as monolithic microwave integrated circuits (MMICs), with measurements showing 7.1 dB gain and 200 GHz bandwidth for the SSDA and 12 dB gain at 170 GHz bandwidth for the three-tier M-SSDA. Details of layout, fabrication and testing; and discussion of performance limiting factors and layout optimization considerations are presented. Drawing on the concept of artificial transmission line synthesis in distributed amplification, a new technique to achieve up to three-fold improvement in the modulation bandwidth of light emitting diodes (LEDs) for visible light communication (VLC) is introduced. The thesis also describes the design and application of analogue pre-emphasis to improve signal-to-noise ratio in bandwidth limited optical transceivers

    A Review of CMOS Low Noise Amplifier for UWB System

    Get PDF
    A number of CMOS low noise amplifier (LNA) design for ultra-wideband (UWB) application had been produced with a various topology and techniques from year 2004 to 2016. The performance of LNA such as frequency bandwidth, noise figure, input and output matching and gain depend with the choice of the topology and technique used. Among the techniques introduced are current reuse, common source, resistive feedback, common gate, Chebyshev filter, distributed amplifier, folded cascade and negative feedback. This paper presents the collection of review about design of low noise amplifier used for UWB application in term of topology circuit. Thus, the problem and limitation of the CMOS LNA for UWB application are reviewed. Furthermore, recent developments of CMOS LNAs are examined and a comparison of the performance criteria of various topologies is presented

    Bandwidth Enhancement Techniques For Cmos Transimpedance Amplifier

    Get PDF
    Tez (Doktora) -- İstanbul Teknik Üniversitesi, Fen Bilimleri Enstitüsü, 2016Thesis (PhD) -- İstanbul Technical University, Institute of Science and Technology, 2016CMOS Transferempedans Kuvvetlendiricinin bandgenis¸lig˘ i bas¸arımını gelis¸tirmeye yönelik teknikler haberles¸me teknolojisinde ve uygulamalarında ortaya çıkan hızlı gelis¸meler ve uygulamalar verilere hızlı eris¸im avantajı yanında hızlı hesaplama ve haberles¸me tekniklerine imkan veren bir bilgi çag˘ ını ortaya çıkarmıs¸tır. Sürekli artan hızlı bilgi transferi ihtiyacı, hızlı elemanların ve tümdevrelerin tasarımına yönelik aras¸tırmalara liderlik eden optik haberles¸me teknig˘ ini dog˘ urmus¸tur. Veri iletimi için mevcut ortamlar arasında optik fiber yapıları en iyi bas¸arımı sunmaktadır. Günümüzde optik fiberler çok yog˘ un sayısal veri transferinde genis¸ kullanım alanı bulmaktadır. Yog˘ un veri aktarımı kilometrelerce uzunlukta optik fiberler üzerinde önemli bir kayıp olmaksızın yapılabilmektedir. Normal s¸artlarda, is¸aret aktarımının ıs¸ık ile yapılması durumunda ortaya çıkan kayıp elektriksel yolla yapılan aktarıma gore daha düs¸üktür. Optik fiberler genel bas¸arımı iyiles¸tirmenin yanında düs¸ük maliyet avantajını da sunmaktadır. En yüksek teknolojilerde, optik fiber elemanları ve sistemleri çok yog˘ un veri aktarımı amacıyla kullanılmaktadır. Sonuç olarak optik fiber teknolojisi düs¸ük kayıpla çok yog˘ un veri aktarımını az maliyetle sunabilen bir teknoloji olarak günümüzde çok önemli bir konuma sahiptir. Genel olarak, optik haberles¸me sistemlerinde kullanılan analog devreler Galyum Arsenik (GaAs) veya Indiyum Fosfid (InP) teknolojileri ile üretilmektedir. Bu prosesler yüksek hızlı devreler için olus¸turulmakta olup optik haberles¸me sistemlerinin ihtiyaç duydug˘ u yüksek band genis¸lig˘ ine sahip devreleri üretmek için genellikle tek alternatif olarak kars¸ımıza çıkmaktadırlar. Bununla birlikte, CMOS proseslerinde ortaya çıkan hızlı gelis¸meler sayesinde daha yüksek bas¸arımlara sahip analog devreleri CMOS proses kullanarak tasarlama ve gerçekles¸tirme imkanları gittikçe artmaktadır. CMOS prosesin tercih edilmesine sebep olan en önemli avantaj maliyetlerde ortaya çıkan büyük düs¸üs¸tür. CMOS proseslerin maliyetinin düs¸ük olmasının sebebi, büyük alan kullanımı gerektiren sayısal devre gerçekles¸tirmelerinde çok genis¸ bir kullanıma sahip olmasıdır. CMOS prosesin dig˘ er bir avantajı sayısal ve analog devrelerin aynı taban üzerinde gerçekles¸tirilmesine imkan vermesidir. Transferempedans kuvvetlendirici (TIA) optik haberles¸me alıcılarındaki ilk blok olup giris¸indeki akımı çıkıs¸ında gerilime dönüs¸türmektedir. Tipik bir TIA’nın önemli bas¸arım ihtiyaçları genis¸ bandgenis¸lig˘ i, yüksek transferempedans kazancı, düs¸ük gürültü, düs¸ük güç tüketimi ve küçük grup geçikme deg˘ is¸im aralıg˘ ıdır. Nano teknolojilerdeki güncel gelis¸meler, optik alıcıların giris¸ katı uygulamalarında gerekli kolay bir s¸ekilde elde edilemeyen bas¸arımları sag˘ layabilen CMOS Transfer- empedans Kuvvetlendiricinin (TIA) tasarımını ekonomik hale getirmis¸tir. TIA tasarımında dikkat edilmesi gereken iki önemli mesele bandgenis¸lig˘ i ve giris¸ hassasiyetidir. TIA’nın bandgenis¸lig˘ i genellikle giris¸teki parasitic kapasite tarafından sınırlanmaktadır. TIA’nın bandgenis¸lig˘ i fotodiyot kapasitesi, transistor giris¸ kapasitesi ve transistor giris¸ direncinin belirledig˘ i RC zaman sabiti ile bulunabilir. Giris¸ hassasiyeti ise TIA’nın giris¸ gürültü akımından etkilenmektedir. Bundan dolayı TIA’nın bandgenis¸lig˘ i ve giris¸ is¸areti hassasiyeti bas¸arımlarını optimum bir s¸ekilde temin eden uygun devre topolojisinin belirlenmesi önemli bir meseledir. Bu tez, CMOS teknolojisi kullanan Transferempedans Kuvvetlendiricinin band- genis¸lig˘ i bas¸arımını gelis¸tirmeye yönelik yeni teknikler sunan bir çalıs¸madır. CMOS TIA’nın bandgenis¸lig˘ i bas¸arımını iyiles¸tirmeye yönelik farklı yaklas¸ımlar tez içerisinde gösterilmektedir. Bundan bas¸ka, bu çalıs¸ma transferempedansı kuvvetlendiricinin analizini ve tasarımını tam olarak anlamak için gerekli altyapı bilgisini de sunmaktadır. Bu tezde, sistemle devre tasarımı arasındaki bos¸lug˘ u doldurmak için s¸unlar yapılmıs¸tır: - Band genis¸lig˘ i bas¸arımının arttırılmasının matematiksel analizlerle anlas¸ılması. - Gerçekles¸tirilebilir yeni devre yapılarının tanıtılması. - Teklif edilen tasarımların CMOS teknolojisiyle gerçekles¸tirilebilirlig˘ inin kapsamlı ve detaylı simülasyonlar kullanılarak gösterilmesi. Sunulan yeni devre yapılarının ilki olarak, negatif empedans devresinin bandgenis¸lig˘ i artıs¸ı için kullanılabileceg˘ i bu tezde gösterilmis¸ olup bu teknik bu tezde TIA’nın çıkıs¸ kutpu için uygulanmaktadır. Bandgenis¸lig˘ i, kazancı (gmRout) arttırarak ve çıkıs¸ta aynı zaman sabiti korunarak arttırılabilir. Çıkıs¸ direnci arttırılarak kazanç (A) yükseltilebilir. Çıkıs¸ direnci çıkıs¸a uygulanacak bir negative direnç devresi ile arttırılabilir. Çıkıs¸ta aynı zaman sabitini korumak için ise negatif kapasite devresi kullanılabilir. Daha yüksek kazanç deg˘ eri (A) rezistif geribesleme sayesinde giris¸ direncini azaltarak giris¸ kutbunun yükselmesini sag˘ lamaktadır. Sonuç olarak, bandgenis¸lig˘ i bas¸arımında bir iyiles¸tirme elde edilebilmektedir. Teklif edilen topoloji ile 7GHz bandgenis¸lig˘ ine ve 54.3dB’lik kazanca sahip bir TIA tasarlanmıs¸tır. Teklif edilen TIA’nın 1.8V’luk besleme kaynag˘ ından çektig˘ i toplam güç 29mW’tır. Teklif edilen TIA’nın 0.18um CMOS proses ile post-serimi yapılmıs¸tır. Benzetimle elde edilmis¸ giris¸ gürültü akım yog˘ unlug˘ u 5.9pA/ Hz olup kapladıg˘ ı alan 230umX45um olmus¸tur. Tezde bir sonraki çalıs¸mada es¸les¸tirme teknig˘ i kullanılarak genis¸ bantlı bs¸r TIA tasarlanmıs¸tır. Giris¸te seri empedans es¸les¸tirme teknig˘ i ve çıkıs¸ta T tipi es¸les¸tirme yapısı birlikte kullanılarak TIA’nın bandgenis¸lig˘ i bas¸arımının iyi bir düzeyde iyiles¸tirilebileceg˘ i gösterilmis¸tir. Bu yaklas¸ım 0.18um CMOS teknolojisi ile yapılmıs¸ bir tasarım örneg˘ i ile desteklenmis¸tir. Post serim sonuçları 50fF’lık bir fotodiyot kapasitesi için 20GHz’lik bandgenis¸lig˘ i, 52.6dB’lik transferdirenci kazancı, 8.7pA/ Hz ‘lik giris¸ gürültü akımı ve 3pS’den daha az grup geçikmesi bas¸arımılarını vermis¸tir. Bu TIA uygulaması 1.8V’luk besleme kaynag˘ ından 1.3mW güç çekmis¸tir. Tezin üçüncü as¸amasında TIA band genis¸lig˘ i bas¸arımını arttırmaya yönelik bas¸ka bir yapı sunulmaktadır. Bu yapı, literatürde bilinen regule edilmis¸ ortak geçitli mimari ile birlikte farklı rezonans frekanslarına sahip iki rezonans devresinin paralel kullanımını içermektedir. Teklif edilen TIA devresinde, kapasite dejenarasyon ve seri endüktif tepe teknikleri kutup-sıfır kompanzasyonu için kullanılmıs¸tır. 100fF’lık fotodiyot kapasitesine sahip bir TIA 0.18um CMOS prosesi ili tasarlanmıs¸tır. Post-serim sonuçları 13GHz’lik bandgenis¸lig˘ i, 53dB’lik transferdirenci kazancı, 24pA/ Hz ‘lik xxvi giris¸ gürültü akımı ve 5pS’den daha az grup geçikmesi bas¸arımılarını vermis¸tir. Bu TIA uygulaması 1.8V’luk besleme kaynag˘ ından 11mW güç çekmis¸tir. Tezin dördüncü as¸amasında, regule edilmis¸ ortak geçitli mimari kullanan TIA’nın bandgenis¸lig˘ i bas¸arımını arttırmaya yönelik bir teknik tanıtılmıs¸tır. Bu teknik, resistif kompanzasyon teknig˘ ini ve merdiven es¸les¸tirme yapısını bir kaskod akım kaynag˘ ı ile birlikte kullanmaya dayanmaktadır. Bu yapının bas¸arımını göstermek amacıyla, 0.18um CMOS prosesi ile bir tasarım yapılmıs¸tır. Post-serim sonuçları 8.4GHz’lik bandgenis¸lig˘ i, 51.3dB’lik transferdirenci kazancı, 20pA/ Hz ‘lik giris¸ gürültü akımı ve 4pS’den daha az grup geçikmesi bas¸arımılarını vermis¸tir. Bu TIA uygulaması 1.8V’luk besleme kaynag˘ ından 17.8mW güç çekmis¸tir. Tezin son as¸amasında, tezde sunulan teknikler ve yapıların kendi aralarında kars¸ılas¸tırılması verilmektedir. Kars¸ılas¸tırma öncelikli olarak band genis¸lig˘ i, transferempedansı kazancı, gürültü, güç tüketimi, grup geçikme deg˘ is¸im aralıg˘ ı ve kapladıg˘ ı alan için yapılmaktadır. Bunlara ek olarak, sunulan yapıların kullandıg˘ ı tekniklerin avantajlı yanları ile birlikte (kararlılık üzerinde olus¸abilecek negatif etkiler gibi) dezavantajlı tarafları da tezin son as¸amasında verilmektedir. Tezin son as¸amasında yapılan kars¸ılas¸tırmalar, en iyi bant genis¸lig˘ i bas¸arımının es¸les¸tirme teknig˘ ini kullanan yapıdan elde edildig˘ ini göstermektedir. Bununla birlikte dig˘ er yapıların da band genis¸lig˘ i bas¸arımı üzerinde önemli iyiles¸tirmeler yaptıg˘ ı ortaya konulmaktadır. Gürültü açısından ise en yüksek bas¸arımın negatif empedans teknig˘ ini kullanan yapıda elde edildig˘ i görülmektedir. Bu yapı aynı zamanda düs¸ük alan kullanımı imkanı da sunmaktadır. Tezde sunulan dig˘ er iki yapı ise özellikle yüksek deg˘ erli fotodiyot kapasiteleri için incelenmis¸ olup band genis¸lig˘ i bas¸arımı üzerinde önemli iyiles¸tirmeler yaptıkları gösterilmektedir. Sonuç olarak, bu tezde transferempedans kuvvetlendiricinin bandgenis¸lig˘ i bas¸arımını iyiles¸tiren farklı teknikler sunulmakta olup bu teknikler ayrıntılı ve kars¸ılas¸tırmalı olarak incelenmektedir. Tezde verilen sonuçlar sunulan yeni tekniklerin bas¸arımlarının yüksek oldug˘ unu ve literature yeni ve güçlü alternatfiler sunuldug˘ unu göstermektedir. Tezde sunulan yaklas¸ımların ve tekniklerin gelecekte yapılacak benzer aras¸tırmalara hem yardımcı olacak hem de referans olacak nitelikte oldug˘ u düs¸ünülmektedir.The accelerated development of integrated systems in the communication technology and their application are among the significant technologies that have developed the information era by empowering high-speed computation and communication technique besides high-speed access to stored data. The continuous growth demand for high-speed transport of information has rekindled optical communications, leading to derived research on high-speed device and integrated circuit design. Among the available medium to transfer the data, optical fibers have the best performance. Optical fibers are very common these days to transport very high rate digital data. Such high speed data rates can be transported over kilometers of optical fiber and without significant loss. Normally loss is very low when the signal is transmitted using light rather than electrical signal. These fibers also have the advantage of being low cost in addition to improvement of performance. In state-of-the-art technology, fiber optic devices and systems are evidently employed to realize very high data rates. Fiber optic communication is a solution because high data rates can be transmitted through this high capacity cable with high performance. Traditionally, analog circuits used in optical communication systems are implemented using Gallium Arsenide (GaAs) or Indium Phosphide (InP) technologies. These processes are designed for high speed circuits, and have been traditionally the only technologies able to produce the high bandwidth circuits required in optical communication systems. However, due to the aggressive scaling of the CMOS process, it is now becoming possible to design high performance analog circuits in CMOS. The primary advantage of moving to a CMOS process is a dramatic reduction in cost due to its widespread use in high volume digital circuits. Another advantage of using CMOS is its ability to integrate digital and analog circuits onto the same substrate. Transimpedance amplifier (TIAs) is the first building block in the optical communication receiver that converts the small signal current to a corresponding output voltage signal. The important requirements of a typical TIA are large bandwidth, high transimpedance gain, low noise, low power consumption, and small group delay variation. Current developments in nanoscale technologies made it economically feasible to design CMOS transimpedance amplifier (TIA) that satisfies the stringent performances necessary for the front-end optical transceivers applications such as low power, low cost and high integration which offers the most economical solution in the consumer application market. In designing of TIA, the two major factors that must be considered are the bandwidth and the input sensitivity. The bandwidth of TIA is usually limited by the parasitic capacitance at the input stage, and it can be calculated by its RC time constant contributed by photodiode capacitance, parasitic capacitance and input resistance of the amplifier. The sensitivity is affected by the input current noise of the TIA. Therefore it is challenge to choose the suitable circuit topology that provides an optimal trade-off between bandwidth and input signal sensitivity for TIA. This thesis is an attempt toward providing novel techniques to extend the bandwidth of the transimpedance amplifier using CMOS technology. Different approaches used to improve the bandwidth of CMOS TIAs are covered. Moreover, this research provides the necessary background knowledge to fully understand the analysis and design of the transimpedance amplifier (TIA). Bridging the gap between system and circuit design is done by: Understanding the bandwidth expansion by mathematical analysis. Introducing new circuit architectures that can be realized. Demonstrating implementation of the proposed designs using extensive simulations in CMOS technology. It is shown in this thesis that, using a negative impedance NI circuit can be used for bandwidth extension. In our application, the negative impedance is incorporated into the output pole of TIA. The bandwidth can be improved by increasing the gain (A = gmRout ) and by maintaining the same time constant at the output pole. A better gain A can be obtained if the output resistance Rout is increased. Increasing Rout can be done by placing a negative resistance RIN in parallel with the output resistance Rout . In order to maintain the same time constant at the output node, a negative capacitance can be used. It have been reported that, the shunt feedback architecture is used to improve the bandwidth of TIA. Increasing the gain A effectively decreases the input resistance and hence increase the frequency of the input pole due to feedback. As a result, an improvement of the bandwidth can be obtained. Using the proposed topology, a wide band transimpedance amplifier with a bandwidth of 7 GH z and transimpedance gain of 54.3 dBΩ is achieved. The total power consumption of the proposed TIA from the 1.8 V power supply is 29 mW . The TIA is designed in 0.18 µ m CMOS technology. The simulated input referred noise current spectral density is 5.9 pA/√H z and the TIA occupies 230µ m × 45µ m of area. Furthermore, a wide band TIA is designed using the matching technique. It is shown that by simultaneously using of series input matching topology and T-output matching network, the bandwidth of the TIA can be obviously improved. This methodology is supported by a design example in a 0.18 µ m CMOS technology. The post layout simulation results show a bandwidth of 20 GH z with 50 f F photodiode capacitance, a transimpedance gain of 52.6 dBΩ, 11 pA/√H z input referred noise and group delay less than 8.3 ps. The TIA dissipates 1.3 mW from a 1.8 V supply voltage. In addition, a new design possessing to extend the bandwidth of the TIA is presented. This TIA employs a parallel combination of two series resonate circuits with different resonate frequencies on the conventional regulated common gate (RGC) architecture. In the proposed TIA, a capacitance degeneration and series inductive peaking technique are used for pole-zero elimination. The TIA is implemented in a 0.18 µ m CMOS process, where a 100 f F photodiode is considered. The post layout simulation results show a transimpedance gain of 53 dBΩ transimpedance gain along with a 13 GH z bandwidth. The designed TIA consumes 11 mW from a 1.8 V supply, and its group-delay variation is 5 ps with 24 pA/√H z input referred noise. xxii In the last phase of the work, a technique to enhance the bandwidth of the regulated common gate (RCG) transimpedance amplifier is described. The technique is based on using a cascode current mirror with resistive compensation technique and a ladder matching network. In order to verify the operation and the performance of the proposed technique, a CMOS design example is designed using the 0.18µ m CMOS process technology. The post layout simulation results show that, the proposed TIA achieved a bandwidth of 8.4 GH z, a transimpedance gain of 51.3 dBΩ and input referred noise current spectral density of 20 pA/√H z. The average group-delay variation is 4 ps over the bandwidth and the TIA consumes 17.8 mW from a 1.8 V supply. To sum up, this thesis focuses on various design techniques of transimpedance amplifier (TIA) that improves the bandwidth performance. We believe that, our approaches and techniques exhibit a path which other future researchers can follow and as well refer to as their researching domain and also could be used in their research applications.DoktoraPh

    Wideband integrated circuits for optical communication systems

    Get PDF
    The exponential growth of internet traffic drives datacenters to constantly improvetheir capacity. Several research and industrial organizations are aiming towardsTbps Ethernet and beyond, which brings new challenges to the field of high-speedbroadband electronic circuit design. With datacenters rapidly becoming significantenergy consumers on the global scale, the energy efficiency of the optical interconnecttransceivers takes a primary role in the development of novel systems. Furthermore,wideband optical links are finding application inside very high throughput satellite(V/HTS) payloads used in the ever-expanding cloud of telecommunication satellites,enabled by the maturity of the existing fiber based optical links and the hightechnology readiness level of radiation hardened integrated circuit processes. Thereare several additional challenges unique in the design of a wideband optical system.The overall system noise must be optimized for the specific application, modulationscheme, PD and laser characteristics. Most state-of-the-art wideband circuits are builton high-end semiconductor SiGe and InP technologies. However, each technologydemands specific design decisions to be made in order to get low noise, high energyefficiency and adequate bandwidth. In order to overcome the frequency limitationsof the optoelectronic components, bandwidth enhancement and channel equalizationtechniques are used. In this work various blocks of optical communication systems aredesigned attempting to tackle some of the aforementioned challenges. Two TIA front-end topologies with 133 GHz bandwidth, a CB and a CE with shunt-shunt feedback,are designed and measured, utilizing a state-of-the-art 130 nm InP DHBT technology.A modular equalizer block built in 130 nm SiGe HBT technology is presented. Threeultra-wideband traveling wave amplifiers, a 4-cell, a single cell and a matrix single-stage, are designed in a 250 nm InP DHBT process to test the limits of distributedamplification. A differential VCSEL driver circuit is designed and integrated in a4x 28 Gbps transceiver system for intra-satellite optical communications based in arad-hard 130nm SiGe process

    Forward Body Biased Low Power 4.0-10.6 GHz Wideband Low Noise Amplifier

    Get PDF
    A forward body biased low power Low Noise Amplifier (LNA) is designed using Common Gate (CG) topology. By using current reuse technique between the first stage and second stage Common Source topology accompanied with forward body biasing leads to low power dissipation. A series to parallel tank circuit at this stage leads to wideband design. A shunt peaking inductor at the drain terminal of second stage causes the higher frequency peak to increase leading to wide bandwidth. Two CS cascade stages are used to increase the overall gain of the proposed LNA with a buffer stage at the output for output matching. The proposed LNA attained maximum gain of 26.39 dB with a gain greater than 16 dB over entire range. The circuit gives reflection coefficient less than – 10 dB with NF 2.7 dB. With Vdd of 0.925 V, a DC current of 8.32 mA is consumed giving 7.7 mW power consumption

    Integrated Distributed Amplifiers for Ultra-Wideband BiCMOS Receivers Operating at Millimeter-Wave Frequencies

    Get PDF
    Millimetre-wave technology is used for applications such as telecommunications and imaging. For both applications, the bandwidth of existing systems has to be increased to support higher data rates and finer imaging resolutions. Millimetrewave circuits with very large bandwidths are developed in this thesis. The focus is put on amplifiers and the on-chip integration of the amplifiers with antennas. Circuit prototypes, fabricated in a commercially available 130nm Silicon-Germanium (SiGe) Bipolar Complementary Metal-Oxide-Semiconductor (BiCMOS) process, validated the developed techniques. Cutting-edge performances have been achieved in the field of distributed and resonant-matched amplifiers, as well as in that of the antenna-amplifier co-integration. Examples are as follows: - A novel cascode gain-cell with three transistors was conceived. By means of transconductance peaking towards high frequencies, the losses of the synthetic line can be compensated up to higher frequencies. The properties were analytically derived and explained. Experimental demonstration validated the technique by a Traveling-Wave Amplifier (TWA) able to produce 10 dB of gain over a frequency band of 170GHz.# - Two Cascaded Single-Stage Distributed Amplifiers (CSSDAs) have been demonstrated. The first CSSDA, optimized for low power consumption, requires less than 20mW to provide 10 dB of gain over a frequency band of 130 GHz. The second amplifier was designed for high-frequency operation and works up to 250 GHz leading to a record bandwidth for distributed amplifiers in SiGe technology. - The first complete CSSDA circuit analysis as function of all key parameters was presented. The typical degradation of the CSSDA output matching towards high frequencies was analytically quantified. A balanced architecture was then introduced to retain the frequency-response advantages of CSSDAs and yet ensure matching over the frequency band of interested. A circuit prototype validated experimentally the technique. - The first traveling-wave power combiner and divider capable of operation from the MHz range up to 200 GHz were demonstrated. The circuits improved the state of the art of the maximum frequency of operation and the bandwidth by a factor of five. - A resonant-matched balanced amplifier was demonstrated with a centre frequency of 185 GHz, 10 dB of gain and a 55GHz wide –3 dB-bandwidth. The power consumption of the amplifier is 16.8mW, one of the lowest for this circuit class, while the bandwidth is the broadest reported in literature for resonant-matched amplifiers in SiGe technology
    corecore