Experimental and simulation study of 1D silicon nanowire transistors using heavily doped channels

The experimental results from 8 nm diameter silicon nanowire junctionless field effect transistors with gate lengths of 150 nm are presented that demonstrate on-currents up to 1.15 mA/m for 1.0 V and 2.52 mA/m for 1.8 V gate overdrive with an off-current set at 100 nA/m. On- to off-current ratios above 108 with a subthreshold slope of 66 mV/dec are demonstrated at 25 oC. Simulations using drift-diffusion which include densitygradient quantum corrections provide excellent agreement with the experimental results. The simulations demonstrate that the present silicon-dioxide gate dielectric only allows the gate to be scaled to 25 nm length before short-channel effects significantly reduce the performance. If high-K dielectrics replace some parts of the silicon dioxide then the technology can be scaled to at least 10 nm gatelength

Development of a fully-depleted thin-body FinFET process

The goal of this work is to develop the processes needed for the demonstration of a fully-depleted (FD) thin-body fin field effect transistor (FinFET). Recognized by the 2003 International Technology Roadmap for Semiconductors as an emerging non-classical CMOS technology, FinFETs exhibit high drive current, reduced short-channel effects, an extreme scalability to deep submicron regimes. The approach used in this study will build on previous FinFET research, along with new concepts and technologies. The critical aspects of this research are: (1) thin body creation using spacer etchmasks and oxidation/etchback schemes, (2) use of an oxynitride gate dielectric, (3) silicon crystal orientation effect evaluation, and (4) creation of fully-depleted FinFET devices of submicron gate length on Silicon-on-Insulator (SOI) substrates. The developed process yielded functional FinFETs of both thin body and wide body variety. Electrical tests were employed to describe device behaviour, including their subthreshold characteristics, standard operation, effects of gate misalignment on device performance, and impact of crystal orientation on device drive current. The process is shown to have potential for deep submicron regimes of fin width and gate length, and provides a good foundation for further research of FinFETs and similar technologies at RIT

Impact of randomly distributed dopants on Ω-gate junctionless silicon nanowire transistors

This paper presents experimental and simulation analysis of an Ω-shaped silicon junctionless nanowire field-effect transistor (JL-NWT) with gate lengths of 150 nm and diameter of the Si channel of 8 nm. Our experimental measurements reveal that the ON-currents up to 1.15 mA/μm for 1.0 V and 2.52 mA/μm for the 1.8-V gate overdrive with an OFF-current set at 100 nA/μm. Also, the experiment data reveal more than eight orders of magnitude ON-current to OFF-current ratios and an excellent subthreshold slope of 66 mV/dec recorded at room temperature. The obtained experimental current-voltage characteristics are used as a reference point to calibrate the simulations models used in this paper. Our simulation data show good agreement with the experimental results. All simulations are based on drift-diffusion formalism with activated density gradient quantum corrections. Once the simulations methodology is established, the simulations are calibrated to the experimental data. After this, we have performed statistical numerical experiments of a set of 500 different JL-NWTs. Each device has a unique random distribution of the discrete dopants within the silicon body. From those statistical simulations, we extracted important figures of merit, such as OFF-current and ON-current, subthreshold slope, and voltage threshold. The performed statistical analysis, on samples of those 500 JL-NWTs, shows that the mean ID-VGs characteristic is in excellent agreement with the experimental measurements. Moreover, the mean ID-VGs characteristic reproduces better the subthreshold slope data obtained from the experiment in comparison to the continuous model simulation. Finally, performance predictions for the JL transistor with shorter gate lengths and thinner oxide regions are carried out. Among the simulated JL transistors, the configuration with 25-nm gate length and 2-nm oxide thickness shows the most promising characteristics offering scalable designs

Modeling and Simulation of Subthreshold Characteristics of Short-Channel Fully-Depleted Recessed-Source/Drain SOI MOSFETs

Non-conventional metal-oxide-semiconductor (MOS) devices have attracted researchers‟ attention for future ultra-large-scale-integration (ULSI) applications since the channel length of conventional MOS devices approached the physical limit. Among the non-conventional CMOS devices which are currently being pursued for the future ULSI, the fully-depleted (FD) SOI MOSFET is a serious contender as the SOI MOSFETs possess some unique features such as enhanced short-channel effects immunity, low substrate leakage current, and compatibility with the planar CMOS technology. However, due to the ultra-thin source and drain regions, FD SOI MOSFETs possess large series resistance which leads to the poor current drive capability of the device despite having excellent short-channel characteristics. To overcome this large series resistance problem, the source/drain area may be increased by extending S/D either upward or downward. Hence, elevated-source/drain (E-S/D) and recessed-source/drain (Re-S/D) are the two structures which can be used to minimize the series resistance problem. Due to the undesirable issues such as parasitic capacitance, current crowding effects, etc. with E-S/D structure, the Re-S/D structure is a better choice. The FD Re-S/D SOI MOSFET may be an attractive option for sub-45nm regime because of its low parasitic capacitances, reduced series resistance, high drive current, very high switching speed and compatibility with the planar CMOS technology. The present dissertation is to deal with the theoretical modeling and computer-based simulation of the FD SOI MOSFETs in general, and recessed source/drain (Re-S/D) ultra-thin-body (UTB) SOI MOSFETs in particular. The current drive capability of Re-S/D UTB SOI MOSFETs can be further improved by adopting the dual-metal-gate (DMG) structure in place of the conventional single-metal-gate-structure. However, it will be interesting to see how the presence of two metals as gate contact changes the subthreshold characteristics of the device. Hence, the effects of adopting DMG structure on the threshold voltage, subthreshold swing and leakage current of Re-S/D UTB SOI MOSFETs have been studied in this dissertation. Further, high-k dielectric materials are used in ultra-scaled MOS devices in order to cut down the quantum mechanical tunneling of carriers. However, a physically thick gate dielectric causes fringing field induced performance degradation. Therefore, the impact of high-k dielectric materials on subthreshold characteristics of Re-S/D SOI MOSFETs needs to be investigated. In this dissertation, various subthreshold characteristics of the device with high-k gate dielectric and metal gate electrode have been investigated in detail. Moreover, considering the variability problem of threshold voltage in ultra-scaled devices, the presence of a back-gate bias voltage may be useful for ultimate tuning of the threshold voltage and other characteristics. Hence, the impact of back-gate bias on the important subthreshold characteristics such as threshold voltage, subthreshold swing and leakage currents of Re-S/D UTB SOI MOSFETs has been thoroughly analyzed in this dissertation. The validity of the analytical models are verified by comparing model results with the numerical simulation results obtained from ATLAS™, a device simulator from SILVACO Inc

Silicon on ferroelectric insulator field effect transistor (SOF-FET) a new device for the next generation ultra low power circuits

Title from PDF of title page, viewed on March 12, 2014Thesis advisor: Masud H. ChowdhuryVitaIncludes bibliographical references (pages 116-131)Thesis (M. S.)--School of Computer and Engineering. University of Missouri--Kansas City, 2013Field effect transistors (FETs) are the foundation for all electronic circuits and processors. These devices have progressed massively to touch its final steps in subnanometer level. Left and right proposals are coming to rescue this progress. Emerging nano-electronic devices (resonant tunneling devices, single-atom transistors, spin devices, Heterojunction Transistors rapid flux quantum devices, carbon nanotubes, and nanowire devices) took a vast share of current scientific research. Non-Si electronic materials like III-V heterostructure, ferroelectric, carbon nanotubes (CNTs), and other nanowire based designs are in developing stage to become the core technology of non-classical CMOS structures. FinFET present the current feasible commercial nanotechnology. The scalability and low power dissipation of this device allowed for an extension of silicon based devices. High short channel effect (SCE) immunity presents its major advantage. Multi-gate structure comes to light to improve the gate electrostatic over the channel. The new structure shows a higher performance that made it the first candidate to substitute the conventional MOSFET. The device also shows a future scalability to continue Moor’s Law. Furthermore, the device is compatible with silicon fabrication process. Moreover, the ultra-low-power (ULP) design required a subthreshold slope lower than the thermionic-emission limit of 60mV/ decade (KT/q). This value was unbreakable by the new structure (SOI-FinFET). On the other hand most of the previews proposals show the ability to go beyond this limit. However, those pre-mentioned schemes have publicized a very complicated physics, design difficulties, and process non-compatibility. The objective of this research is to discuss various emerging nano-devices proposed for ultra-low-power designs and their possibilities to replace the silicon devices as the core technology in the future integrated circuit. This thesis proposes a novel design that exploits the concept of negative capacitance. The new field effect transistor (FET) based on ferroelectric insulator named Silicon-On-Ferroelectric Insulator Field Effect Transistor (SOF-FET). This proposal is a promising methodology for future ultra-lowpower applications, because it demonstrates the ability to replace the silicon-bulk based MOSFET, and offers subthreshold swing significantly lower than 60mV/decade and reduced threshold voltage to form a conducting channel. The SOF-FET can also solve the issue of junction leakage (due to the presence of unipolar junction between the top plate of the negative capacitance and the diffused areas that form the transistor source and drain). In this device the charge hungry ferroelectric film already limits the leakage.Abstract -- List of illustrations - List of tables -- Acknowledgements -- Dedication -- Introduction -- Carbon nanotube field effect transistor -- Multi-gate transistors -FinFET -- Subthreshold swing -- Tunneling field effect transistors -- I-mos and nanowire fets -- Ferroelectric based field effect transistors -- An analytical model to approximate the subthreshold swing for soi-finfet -- Silicon-on-ferroelectric insulator field effect transistor (SOF-FET) -- Current-voltage characteristics of sof-fet -- Advantages, manufacturing process and future work of the proposed device -- Appendix -- Reference

Oxygen-insertion Technology for CMOS Performance Enhancement

Until 2003, the semiconductor industry followed Dennard scaling rules to improve complementary metal-oxide-semiconductor (CMOS) transistor performance. However, performance gains with further reductions in transistor gate length are limited by physical effects that do not scale commensurately with device dimensions: short-channel effects (SCE) due to gate-leakage-limited gate-oxide thickness scaling, channel mobility degradation due to enhanced vertical electric fields, increased parasitic resistances due to reductions in source/drain (S/D) contact area, and increased variability in transistor performance due to random dopant fluctuation (RDF) effects and gate work function variations (WFV). These emerging scaling issues, together with increased process complexity and cost, pose severe challenges to maintaining the exponential scaling of transistor dimensions. This dissertation discusses the benefits of oxygen-insertion (OI) technology, a CMOS performance booster, for overcoming these challenges. The benefit of OI technology to mitigate the increase in sheet resistance ($R_{sh}$) with decreasing junction depth ($X_J$) for ultra-shallow-junctions (USJs) relevant for deep-sub-micron planar CMOS transistors is assessed through the fabrication of $R_{sh}$ test structures, electrical characterization, and technology computer-aided design (TCAD) simulations. Experimental and secondary ion mass spectroscopy (SIMS) analyses indicate that OI technology can facilitate low-resistivity USJ formation by reducing $R_{sh}$ and $X_J$ due to retarded transient-enhanced-diffusion (TED) effects and enhanced dopant retention during post-implantation thermal annealing. It is also shown that a low-temperature-oxide (LTO) capping can increase $R_{sh}$ unfavorably due to lower dopant activation levels, which can be alleviated by OI technology. This dissertation extends the evaluation of OI technology to advanced FinFET technology, targeting 7/8-nm low power technology node. A bulk-Si FinFET design comprising a super-steep retrograde (SSR) fin channel doping profile achievable with OI technology is studied by three-dimensional (3-D) TCAD simulations. As compared with the conventional bulk-Si (control) FinFET design with a heavily-doped fin channel doping profile, SSR FinFETs can achieve higher $I_{on}/I_{off}$ ratios and reduce the sensitivity of device performance to variations due to the lightly doped fin channel. As compared with the SOI FinFET design, SSR FinFETs can achieve similarly low $V_{DD,min}$ for 6T-SRAM cell yield estimation. Both SSR and SOI design can provide for as much as 100 mV reduction in $V_{DD,min}$ compared with the control FinFET design. Overall, the SSR FinFET design that can be achieved with OI technology is demonstrated to be a cheaper alternative to the SOI FinFET technology for extending CMOS scaling beyond the 10-nm node. Finally, this dissertation investigates the benefits of OI technology for reducing the Schottky barrier height ($\Phi_{Bp}$) of a Pt/Ti/p-type Si metal-semiconductor (M/S) contact, which can be expected to help reduce the specific contact resistivity for a p-type silicon contact. Electrical measurements of back-to-back Schottky diodes, SIMS, and X-ray photoelectron spectroscopy (XPS) show that the reduction in $\Phi_{Bp}$ is associated with enhanced Ti 2p and Si 2p core energy level shifts. OI technology is shown to favor low-$\Phi_{Bp}$ Pt monosilicide formation during forming gas anneal (FGA) by suppressing the grain boundary diffusion of Pt atoms into the crystalline Si substrate

Design Strategies for Ultralow Power 10nm FinFETs

Integrated circuits and microprocessor chips have become integral part of our everyday life to such an extent that it is difficult to imagine a system related to consumer electronics, health care, public transportation, household application without these small components. The heart of these circuits is, the metal oxide field-effect transistor (MOSFET) which is used as a switch. The dimensions of these transistors have been scaled from a few micrometers to few tens of nanometer to achieve higher performance, lower power consumption and low cost of production. According to the International Technology Roadmap for Semiconductors (ITRS), beyond 32 nm technology node, planer devices will not be able to fulfill the strict leakage requirement anymore due to overpowering short channel effects and need of multi-gate transistor is inevitable. The motivation of the thesis therefore is to investigate techniques to engineer threshold voltage of a tri-gate FinFET for low power and ultra-low power applications. The complexity of physics involved in 3D nano- devices encourages use of advanced simulation tools. Thus, Technology Computer Aided Design Tools (TCAD) are needed to perform device optimization and support device and process integration engineers. Below 20nm technology node, the Fin-shaped Field Effect Transistor or Tri-gate transistor requires extensive use of 3D TCAD simulations. The multi-gate devices such as FinFETs are considered to be one of the most promising devices for Ultra Large Scale Integration (ULSI). This device structural design with additional gate electrodes and channel surfaces offers dynamic threshold voltage control. In addition, it can provide better short channel performance and reduced leakage. In this study, new design strategies for 10nm node NMOS bulk FinFET transistors are investigated to meet low power (LP) (50pA/μ