Efficient and Wideband Load Modulated Power Amplifiers for Wireless Communication

The increasing demand for mobile data traffic has resulted in new challenges and requirements for the development of the wireless communication infrastructure. With the transition to higher frequencies and multi-antenna systems, radio frequency (RF) hardware performance, especially the power amplifier (PA), becomes increasingly important. Enhancing PA energy efficiency and bandwidth is vital for maximizing channel capacity, reducing operational costs, and facilitating integration.In the first part of the thesis, the bandwidth limitations of the standard two-way Doherty PA are discussed. A comprehensive analysis is provided, and the frequency responses of different Doherty combiner networks are presented. Furthermore, a Doherty combiner network is proposed, notable for its inherent broadband frequency and its capacity to account for the influence of output parasitics and packaged components from the active devices. The introduced Doherty combiner network is experimentally verified by a wideband gallium nitride (GaN) Doherty PA operating over 1.6-2.7 GHz.In the second part of the thesis, an analytically based combiner synthesis approach for the three-stage Doherty PA is proposed and presented. A compact output combiner network, together with the input phase delays, is derived directly from transistor load-pull data and the PA design requirements. The technique opens up new design space for three-stage Doherty PAs with reconfigurable high-efficiency power back-off levels. The utility of the proposed technique is demonstrated by the implementation of a 30-W GaN three-stage Doherty PA prototype at 2.14 GHz. Measurements show that a drain efficiency of 68% and 55% is exhibited at 6- and 10-dB back-off power, respectively.In the third part, a new PA architecture named the circulator load modulated amplifier (CLMA), is proposed. This architecture utilizes active load modulation for achieving enhanced back-off efficiency. Two active devices are incorporated in this innovative architecture, and a non-reciprocal circulator-based combiner is leveraged. Following this, the sequential CLMA (SCLMA) is introduced, characterized by its ability to enhance back-off efficiency without the necessity of load modulation. GaN demonstrator circuits for both CLMA and SCLMA architectures, whether with dual-input or RF single-input, are designed and fabricated, with excellent performance being measured.\ua0The thesis contributes novel design techniques and architectures to enhance PA efficiency and bandwidth. These findings pave the way for energy-efficient and adaptable RF transmitters in future wireless communication systems

Advanced High Efficiency and Broadband Power Amplifiers Based on GaN HEMT for Wireless Applications

In advanced wireless communication systems, a rapid increase in the mobile data traffic and broad information bandwidth requirement can lead to the use of complex spectrally efficient modulation schemes such as orthogonal frequency-division multiplexing (OFDM). Generally, complex non-constant envelope modulated signals have very high peak-to-average ratios (PAPR). Doherty Power Amplifier (DPA) is the most commonly used power amplifier (PA) architecture for meeting high efficiency requirement in advanced communication systems, in the presence of high PAPR signals. However, limited bandwidth of the conventional DPA is often identified as a bottleneck for widespread deployment in base-station application for multi-standard communication signals. The research in this thesis focuses on the development of new designs to overcome the bandwidth limitations of a conventional PA. In particular, the bandwidth limitation factors of a conventional DPA architecture are studied. Moreover, a novel design technique is proposed for DPA’s bandwidth extension. In the first PA design, limited bandwidth and linearity problems are addressed simultaneously. For this purpose, a new Class-AB PA with extended bandwidth and improved linearity is presented for LTE 5 W pico-cell base-station over a frequency range of 1.9–2.5 GHz. A two-tone load/source-pull and bias point optimization techniques are used to extract the sweet spots for optimum efficiency and linearity from the 6 W Cree GaN HEMT device for the whole frequency band. The realized prototype presented saturated PAE higher than 60%, a power gain of 13 dB and an average output power of 36.5 dBm over the desired bandwidth. The proposed PA is also characterized by QAM-256 and LTE input communication signals for linearity characterization. Measured ACPRs are lower than -40 dBc for an input power of 17 dBm. The documented results indicate that the proposed Class-AB architecture is suitable for pico-cell base-station application. In the second PA design, an inherent bandwidth limitation of Class-F power amplifier forced by the improper load harmonics terminations at multiple harmonics is investigated and analyzed. It is demonstrated that the impedance tuning of the second and third harmonics at the drain terminal of a transistor is crucial to achieve a broadband performance. The effect of harmonics terminations on power amplifier’s bandwidth up to fourth harmonics is investigated. The implemented broadband Class-F PA achieved maximum saturated drain efficiency 60-77%, and 10 W output power throughout (1.1-2.1 GHz) band. The simulated and measured results verify that the presented Class-F PA is suitable for a high-efficiency system application in wireless communications over a wide range of frequencies. In the third PA design, a single- and dual-input DPA for LTE application in the 3.5 GHz frequency band are presented and compared. The main goal of this study is to improve the performance of gallium–nitride (GaN) Doherty transmitters over a wide bandwidth in the 3.5 GHz frequency band. For this purpose, the linearity-efficiency trade-off for the two proposed architectures is discussed in detail. Simulated results demonstrate that the single- and dual-input DPA exhibited a peak drain efficiency (DE) of 72.4% and 77%, respectively. Both the circuits showed saturated output power more than 42.9 dBm throughout the designed band. Saturated efficiency, gain and bandwidth of dual-input DPA are higher than that of the single-input DPA. On the other side, dual-input DPA linearity is worse as compared to the single-input DPA. In the last PA design, a novel design methodology for ultra-wide band DPA is presented. The bandwidth limitation factors of the conventional Doherty amplifier are discussed on the ground of broadband matching with impedance variation. To extend the DPA bandwidth, three different methods are used such as post-matching, low impedance transformation ratio and the optimization of offset line for wide bandwidth in the proposed design. The proposed Doherty power amplifier was designed and realized based on two 10 W GaN HEMT devices from Cree Inc. The measured results exhibited 42-57% of efficiency at the 6-dB back-off and saturated output power ranges from 41.5 to 43.1 dBm in the frequency range of 1.15 to 2.35 GHz (68.5% fractional bandwidth). Moreover, less than -25 dBc ACPRs are measured at 42 dBm peak output power throughout the designed band. In a nutshell, all power amplifiers presented in this thesis are suitable for wideband operation and their performances are satisfying the required operational standard. Therefore, this thesis has a significant contribution in the domain of high efficiency and broadband power amplifiers

AC Power Combining Strategy with Application to Efficient Linear Power Amplifiers

With the ongoing push for wireless systems to accommodate more users and support higher data rates more efficient modulation schemes have been created that are more advanced than simple FM and AM modulation used for radio broadcasting. These modulation schemes, such as orthogonal frequency division multiplexing (OFDM), suffer from high peak to average power ratios. Standard Class A and Class AB amplifiers cannot simultaneously achieve good linearity and efficiency, and therefore there has been an increase in the development of new topologies to combat this issue. Common features to these circuits is power combining of two or more separate transistors. In this work, we consider various ways of two-source power combining and identify four topologies of interest. We notice that linear power-efficient amplifiers reported to date are based upon two of the identified combining strategies. We believe that no amplifiers have been reported that leverage the other two alternatives. This work produces a fully-functional amplifier based on one of these alternatives. The prototypes are intended to serve as concept verification of the architecture and hence are implemented at lower (1 MHz) frequencies

Transmissor RF de elevado rendimento com duas entradas digitais para sistemas 5G

In recent years, there has been a need to increase the capacity and speed of information transmission, so the communication signals used in mobile communications have been improved to meet the expectations. This will be even more significant in future 5G systems, since due to the high expansion of wireless devices, current 4G systems are starting to push their limits, where only small improvements can be achieved. Which complicates the design of transmitters, since these new signals have a wider bandwidth and a large variation between their average and peak value, causing amplifiers to operate most of the time in a zone where they are not as efficient. For this reason, amplifier architectures not only aim to have high efficiency when operating at maximum signal excursion, but also to increase efficiency in the zone where they will operate most of the time. For this purpose, there are architectures based on supply voltage modulation and load modulation to improve the efficiency at lower powers. This work addresses load modulation architectures, where Doherty and Chireix are the most prominent. In addition, with the increase in digital signal processing capabilities, new amplification architectures based on the load modulation technique have recently been proposed, but instead of using only one RF input, they use two independent digitally controlled inputs. This dissertation aims at implementing a Doherty-Chireix amplifier with two digital inputs to achieve efficient amplification for the 1.7 to 2.4GHz frequency band. In the end it was possible to design and implement a Doherty-Chireix power amplifier, with 700MHz bandwidth, with a gain between 13.9-11.3dB, a maximum power of 45dBm, a PAE of over 60% and peak-to-average power ratio between 5.2-4.1dB.Nos últimos anos, tem havido uma necessidade de aumentar a capacidade e velocidade de transmissão de informação, deste modo os sinais de comunicação utilizados nas comunicações móveis têm evoluído por forma a corresponder as expectativas. Tal será ainda mais significativo nos futuros sistemas 5G, já que devido à elevada expansão de dispositivos sem fio, os atuais sistemas 4G estão a começar a atingir os seus limites, onde apenas pequenas melhorias podem ser alcançadas. Isto vem complicar o projeto dos transmissores, uma vez que estes novos sinais apresentam uma maior largura de banda e uma grande variação entre o seu valor médio e de pico, fazendo com que os amplificadores operem na maior parte do tempo numa zona em que não são tão eficientes. Por esta razão, as arquiteturas de amplificação nos dias de hoje não só visam ter um grande rendimento quando operam com a máxima excursão de sinal, mas também o aumento do rendimento na zona onde irão operar a maior parte do tempo. Nesse sentido existem arquiteturas baseadas em modelação de tensão de alimentação e modelação de carga de modo a melhorar a eficiência a potências mais baixas. Neste trabalho são abordadas arquiteturas de modulação de carga, onde Doherty e Chireix são as que mais se destacam. Para além disso, com o aumento da capacidade de processamento digital de sinal, recentemente foram propostas novas arquiteturas de amplificação que se baseiam nestas técnicas, mas em vez de utilizar apenas uma entrada de RF, usam duas entradas independentes controladas digitalmente. Esta dissertação visa a implementação de um amplificador Doherty-Chireix com duas entras digitais de modo a obter uma amplificação eficiente para uma banda de frequências de 1.7 a 2.4GHz. No final foi possível projetar e implementar um amplificador de potência Doherty-Chireix, com 700MHz de largura de banda, com um ganho compreendido entre 13.9-11.3dB, potência máxima de 45dBm, uma PAE superior a 60% e peak-to-average power ratio entre 5.2-4.1dB.Mestrado em Engenharia Eletrónica e Telecomunicaçõe

High-Power Microwave/ Radio-Frequency Components, Circuits, and Subsystems for Next-Generation Wireless Radio Front-Ends

As the wireless communication systems evolve toward the future generation, intelligence will be the main signature/trend, well known as the concepts of cognitive and software-defined radios which offer ultimate data transmission speed, spectrum access, and user capacity. During this evolution, the human society may experience another round of `information revolution\u27. However, one of the major bottlenecks of this promotion lies in hardware realization, since all the aforementioned intelligent systems are required to cover a broad frequency range to support multiple communication bands and dissimilar standards. As the essential part of the hardware, power amplifiers (PAs) capable of operating over a wide bandwidth have been identified as the key enabling technology. This dissertation focuses on novel methodologies for designing and realizing broadband high-power PAs, their integration with high-quality-factor (high-Q) tunable filters, and relevant investigations on the reliabilities of these tunable devices. It can be basically divided into three major parts: 1.Broadband High-Efficiency Power Amplifiers. Obtaining high PA efficiency over a wide bandwidth is very challenging, because of the difficulty of performing broadband multi-harmonic matching. However, high efficiency is the critical feature for high-performance PAs due to the ever-increasing demands for environmental friendliness, energy saving, and longer battery life. In this research, novel design methodologies of broad-band highly efficient PAs are proposed, including the first-ever mode-transferring PA theory, novel matching network topology, and wideband reconfigurable PA architecture. These techniques significantly advance the state-of-the-art in terms of bandwidth and efficiency. 2.Co-Design of PAs and High-Q Tunable Filters. When implementing the intelligent communication systems, the conventional approach based on independent RF design philosophy suffers from many inherent defects, since no global optimization is achieved leading to degraded overall performance. An attractive method to solve these difficulties is to co-design critical modules of the transceiver chain. This dissertation presents the first-ever co-design of PAs and tunable filters, in which the redundant inter-module matching is entirely eliminated, leading to minimized size & cost and maximized overall performance. The saved hardware resources can be further transferred to enhance system functionalities. Moreover, we also demonstrate that co-design of PAs and filters can lead to more functionalities/benefits for the wireless systems, e.g. efficient and linear amplification of dual-carrier (or multi-carrier) signals. 3.High-Power/Non-Linear Study on Tunable Devices. High-power limitation/power handling is an everlasting theme of tunable devices, as it determines the operational life and is the threshold for actual industrial applications. Under high-power operation, the high RF voltage can lead to failures like tuners\u27 mechanical deflections and gas discharge in the small air spacing of the cavity. These two mechanisms are studied independently with their instantaneous and long-term effects on the device performance. In addition, an anti-biased topology of electrostatic RF MEMS varactors and tunable filters is proposed and experimentally validated for reducing the non-linear effect induced by bias-noise. These investigations will enlighten the designers on how to avoid and/or minimize the non-ideal effects, eventually leading to longer life cycle and performance sustainability of the tunable devices

Amplifier Architectures for Wireless Communication Systems

Ever-increasing demand in modern wireless communication systems leads researchers to focus on design challenges on one of the main components of RF transmitters and receivers, namely amplifiers. On the transmitter side, enhanced efficiency and broader bandwidth over single and multiple bands on power amplifiers will help to have superior performance in communication systems. On the other hand, for the receiver side, having low noise and high gain will be necessary to ensure good quality transmission over such systems. In light of these considerations, a unique approach in design methodologies are studied with low noise amplifiers (LNAs) for RF receivers and the Doherty technique is analyzed for efficiency enhancement for power amplifiers (PA) on the transmitters. This work can be outlined in two parts. In the first part, Low Noise RF amplifier designs with Bipolar Junction Transistor (BJT) are studied to achieve better performing LNAs for receivers. The aim is to obtain a low noise figure while optimizing the bandwidth and achieving a maximum available gain. There are two designs that are operating at different center frequencies and utilizing different transistors. The first design is a wideband low-noise amplifier operating at 2 GHz with a high power BJT. The proposed design uses only distributed elements to realize the input and output matching networks. Additionally, a passive DC bias network is used instead of an active DC bias network to avoid possible complications due to the lumped elements parasitic effects. The matching networks are designed based on the reflection coefficients that are derived based on the transistor’s available regions. The second design is a low voltage standing wave ratio (VSWR) amplifier with a low noise figure operating at 3 GHz. This design is following the same method as in the first design. Both these amplifiers are designed to operate in broadband applications and can be good candidates for base stations. The second part of this work focuses on the transmitter side of communication systems. For this part, Doherty Power Amplifier (DPA) is analyzed as an efficiency enhancement technique for PAs. A modified architecture is proposed to have wider bandwidth and higher efficiency. In the proposed design, the quarter-wave impedance inverter was eliminated. The input and the output of the main and peak amplifiers are matched to the load directly. Additionally, the input and output matching networks are realized only using distributed elements. The selected transistor for this design is a 10 W Gallium Nitride (GaN). The fabricated amplifier operates at the center frequency of 2 GHz and provides 40% fractional bandwidth, 54% of maximum power-added efficiency, and 12.5 dB or better small-signal gain. The design is showing promising results to be a good candidate for better-performing transmitters over the L- and S- band

On the design of high-efficiency RF Doherty power amplifiers

Power amplifiers (PAs) are one of the most crucial elements in wireless standards becasue they are the most power hungry subsystems. These elements have to face an important issue, which is the power efficiency, a fact related with the output back-off (OBO). But the OBO depends on the kind of modulated signal, in proportion to the modulated signal peak-to-average power ratio (PAPR). The higuer is the data rate, the higer is the OBO, and consequently the lower is the efficiency. A low efficiency of PAs causes the waste of energy as heat. Furthermore, the trade-off between linearity and efficiency in PAs is another major issue. To cope with the undesired circumstances producing efficiency degradation, the Doherty power amplifier (DPA) is one of the useful techniques which provide high efficiency for high PAPR of modern communication signals. Nevertheless, the limited bandwidth (BW) of this kind of PAs (about 10% of fractional bandwidth) and its importance (in modern wireless systems such as LTE, WiMAX, Wi-Fi and satellite systems) have encouraged the researchers to improve this drawback in recent years. Some typical BW limiting factors effect on the performance of DPAs: i) quarter-wave length transformers, ii) phase compensation networks in/output matching circuits, iii) offset lines and device non-idealities; The quarter-wave length transformers performs as an inverter impedance in the load modulation technique of DPAs. The future objective in designing DPAs is to decrease the impact of these issues. In this context, this PhD-thesis is focused on improving fractional bandwidth of DPAs using the new methods that are related to impedance transformers instead of impedance inverters in the load modulation technique. This study is twofold. First, it is presented a novel DPA where a wideband GaN DPA in the 2.5 GHz band with an asymmetrical Wilkinson splitter. The impedance transformer of the proposed architecture is based on a matching network including a tapered line with multi-section transformer in the main stage. The BW of this DPA has ranged from 1.8 to 2.7 GHz. Plus, the obtained power efficiency (drain) is higher than 33% in the whole BW at both maximum and OBO power levels. Second, based on the benefits of the Klopfenstein taper, a promising DPA design is proposed where a Klopfenstein taper replaces the tapered line. In fact, this substitution results on reducing the reflection coefficient of the transformer. From a practical prototype realization of this novel Doherty-like PA in the 2.25 GHz band, this modification has demonstrated that the resulting DPA BW is increased in comparison to the conventional topology while keeping the efficiency figures. Moreover, this study also shows that the Klopfenstein taper based design allows an easy tuning of the group delay through the output reactance of the taper, resulting in a more straightforward adjustments than other recently published designs where the quarter-wave transformer is replaced by multi-section transmission lines (hybrid or similar). Experimental results have shown 43-54% of drain efficiency at 42 dBm output power, in the range of 1.7 to 2.75 GHz. Concretely, the results presented in this novel Doherty-like PA implies an specific load modulation technique that uses the mixed Klopfenstein tapered line together with a multi-section transformer in order to obtain high bandwidth with the usual efficiency in DPAs.Los amplificadores de potencia (PAs) son uno de los elementos más importantes para los transmisores inalámbricos desde el punto de vista del consumo energético. Un aspecto muy importante es su eficiencia energética, un concepto relacionado con el back-off de salida (OBO), que a su vez viene condicionadpo por el PAPR de la señal modulada a amplificar. Una baja eficiencia de los PA hace que la pérdida de energía se manifieste en forma de calor. De hecho, esta cuestión conduce al incremento de los costes y tamaño, esto último por los radiadores. Además, el compromiso entre la linealidad y la eficiencia en los PA es otro problema importante. Para hacer frente a las circunstancias que producen la degradación de la eficiencia, el amplificador de potencia tipo Doherty (DPA) es una de las técnicas más útiles que proporcionan una buena eficiencia incluso para los altos PAPR comunes en señales de comunicación modernos. Sin embargo, el limitado ancho de banda (BW) de este tipo de PA (alrededor del 10% del ancho de banda fraccional) y su importancia (en los sistemas inalámbricos modernos, tales como LTE, WiMAX, Wi-Fi y sistemas de satélites) han animado a los investigadores para mejorar este inconveniente en los últimos años. Algunos aspectos típicos que limitan el BW en los DPA son: i) transformadores de longitud de cuarto de onda, ii) redes de compensación de fase y circuitos de adaptación de salida, iii) compensación de las líneas y los dispositivos no ideales. Los transformadores de cuarto de onda actuan como un inversor de impedancia en la técnica de modulación de carga de la DPA "("load modulation"). Concretamente, el objetivo futuro de diseño de DPA es disminuir el impacto de estos problemas. En este contexto, esta tesis doctoral se centra en mejorar el ancho de banda fraccional de DPA utilizando los nuevos métodos que están relacionados con el uso de transformadores de impedancias en vez de inversores en el subcircuito de modulación de carga. Este estudio tiene dos niveles. En primer lugar, se presenta una novedosa estructura del DPA de banda ancha usándose dispositivos de GaN en la banda de 2,5 GHz con un divisor Wilkinson asimétrico. El transformador de impedancias de la arquitectura propuesta se basa en una red de adaptación, incluyendo una línea cónica con múltiples secciones del transformador en la etapa principal. El BW de este DPA ha sido de 1,8 a 2,7 GHz. Además, se obtiene una eficiencia de drenador de más del 33% en todo el BW, tanto a nivel de potencia máxima como a nivel del OBO. En segundo lugar, aprovechando los beneficios de un adaptador de Klopfenstein, se propone un nuevo diseño del DPA. Con la sustitución de la lina conica por el Klopfenstein se reduce el coeficiente de reflexión de transformador de impedancias. Sobre un prototipo práctico de esta nueva estructura del Doherty, en la banda de 2,25 GHz, se ha demostrado que el BW resultante se incrementa en comparación con la topología convencional mientras se mantienen las cifras de eficiencia. Por otra parte, en este estudio se demuestra que el diseño basado en el Klopfenstein permite una afinación fácil del retardo de grupo a través de la reactancia de salida del taper, lo que resulta en un ajuste más sencillo que otros diseños publicados recientemente en el que el transformador de cuarto de onda se sustituye por multi-líneas de transmisión de la sección (híbridos o similar). Los resultados experimentales han mostrado un 43-54% de eficiencia de drenador sobre 42 dBm de potencia de salida, en el intervalo de 1,7 a 2,75 GHz. Concretamente, los resultados presentados en esta nueva estructura tipo-Doherty implican una técnica de modulación de carga que utiliza una combinación de un Klopfenstein junto con un transformador de múltiples secciones con el fin de obtener un alto ancho de banda con la eficiencia habitual en DPAs.Els amplificadors de potència (PA) són un dels elements més importants per els sistemes ràdio ja que sone ls principals consumidors d'energía. Un aspecte molt important és l'eficiència de l'amplificador, aspecte relacionat amb el back-off de sortida (OBO) que a la seva vegada ve condicionat pel PAPR del senyal modulat. Una baixa eficiència dels PA fa que la pèrdua d'energia en manifesti en forma de calor. De fet, aquesta qüestió porta a l'increment dels costos i grandària, degut als dissipadors de calor. A més, el compromís entre la linealitat i l'eficiència en els PA es un altre problema important. Per fer front a les circumstàncies que porten a la degradació de l'eficiència, l'amplificador de potència Doherty (DPA) és una de les tècniques més útils i que proporcionen una bona eficiència per als alts PAPR comuns en senyals de comunicació moderns. No obstant això, l'ample de banda limitat (BW) d'aquest tipus de PA (al voltant del 10% de l'ample de banda fraccional) i la seva importància (en els sistemes moderns, com ara LTE, WiMAX, Wi-Fi i sistemes de satèl·lits) han animat els investigadors per millorar aquest inconvenient en els últims anys. Alguns aspectes tipicament limitadors del BW en els DPA son: i) transformadors de longitud d'quart d'ona, ii) xarxes de compensació de fase en circuits / adaptacions de sortida, iii) compensació de les línies i els dispositius no ideals. Els transformadors de quart d'ona s'utilitzen com a inversors d'impedàncies en la tècnica de modulació de càrrega del DPA ("load modulation"). Concretament, l'objectiu futur de disseny d'DPA és disminuir l'impacte d'aquests problemes. En aquest context, aquesta tesi doctoral es centra en millorar l'ample de banda fraccional dels DPA utilitzant nous mètodes que estan relacionats amb l'ús de transformadors d'impedàncies, en comptes d'inversors, en el subcircuit de modulació de càrrega. Aquest treball té dos nivells. En primer lloc, es presenta un DPA novedós que fa servir dispositus GaN DPA a la banda de 2,5 GHz amb un divisor Wilkinson asimètric. El transformador d'impedàncies de l'arquitectura proposada es basa en una xarxa d'adaptació, incloent una línia cònica amb múltiples seccions del transformador en l'etapa principal. El BW d'aquest DPA ha mostrat ser d'1,8 a a 2,7 GHz. A més, s'obté una eficiència de drenador de més del 33% en tot el BW, tant a nivell de potència màxima com de OBO. En segon lloc, sobre la base dels beneficis del adaptador de Klopfenstein, un proposa un nou disseny on un Klopfenstein substitueix la anterior línia cònica. Aquesta substitució repercuteix en la reducció del coeficient de reflexió de transformador d'impedàncies.Des d'una realització pràctica (prototipus) d'aquest nou amplificador tipus Doherty a la banda de 2,25 GHz, s'ha demostrat que el BW resultant s'incrementa en comparació amb la topologia convencional mentre es mantenen les xifres d'eficiència. D'altra banda, en aquest estudi es demostra que el disseny basat en el Klopfenstein permet una afinació fàcil del retard de grup a través de la reactància de sortida de la forma cònica, el que resulta en un ajust més senzill que altres dissenys publicats recentment en què el transformador de quart d'ona es substitueix per multi-línies de transmissió de la secció (híbrids o similar). Els resultats experimentals han mostrat un 43-54% d'eficiència de drenador en 42 dBm de potència de sortida, en l'interval de 1,7-2,75 GHz. Concretament, els resultats presentats en aquest nou amplificador tipus Doherty impliquen una tècnica de modulació de càrrega específic que utilitza una combinació del Klopfenstein juntament amb un transformador de múltiples seccions per tal d'obtenir un alt ample de banda amb la usual eficiència en DPAs.Postprint (published version

Design of a wideband doherty power amplifier with high efficiency for 5g application

This paper discusses the design of a wideband class AB-C Doherty power amplifier suitable for 5G applications. Theoretical analysis of the output matching network is presented, focusing on the impact of the non-ideally infinite output impedance of the auxiliary amplifier in back off, due to the device’s parasitic elements. By properly accounting for this effect, the designed output matching network was able to follow the desired impedance trajectories across the 2.8 GHz to 3.6 GHz range (fractional bandwidth = 25%), with a good trade-off between efficiency and bandwidth. The Doherty power amplifier was designed with two 10 W packaged GaN HEMTs. The measurement results showed that it provided 43 dBm to 44.2 dBm saturated output power and 8 dB to 13.5 dB linear power gain over the entire band. The achieved drain efficiency was between 62% and 76.5% at saturation and between 44% and 56% at 6 dB of output power back-off

Vidutinių dažnių 5G belaidžių tinklų galios stiprintuvų tyrimas

This dissertation addresses the problems of ensuring efficient radio fre-quency transmission for 5G wireless networks. Taking into account, that the next generation 5G wireless network structure will be heterogeneous, the device density and their mobility will increase and massive MIMO connectivity capability will be widespread, the main investigated problem is formulated – increasing the efficiency of portable mid-band 5G wireless network CMOS power amplifier with impedance matching networks. The dissertation consists of four parts including the introduction, 3 chapters, conclusions, references and 3 annexes. The investigated problem, importance and purpose of the thesis, the ob-ject of the research methodology, as well as the scientific novelty are de-fined in the introduction. Practical significance of the obtained results, defended state-ments and the structure of the dissertation are also included. The first chapter presents an extensive literature analysis. Latest ad-vances in the structure of the modern wireless network and the importance of the power amplifier in the radio frequency transmission chain are de-scribed in detail. The latter is followed by different power amplifier archi-tectures, parameters and their improvement techniques. Reported imped-ance matching network design methods are also discussed. Chapter 1 is concluded distinguishing the possible research vectors and defining the problems raised in this dissertation. The second chapter is focused around improving the accuracy of de-signing lumped impedance matching network. The proposed methodology of estimating lumped inductor and capacitor parasitic parameters is dis-cussed in detail provi-ding complete mathematical expressions, including a summary and conclusions. The third chapter presents simulation results for the designed radio fre-quency power amplifiers. Two variations of Doherty power amplifier archi-tectures are presented in the second part, covering the full step-by-step de-sign and simulation process. The latter chapter is concluded by comparing simulation and measurement results for all designed radio frequency power amplifiers. General conclusions are followed by an extensive list of references and a list of 5 publications by the author on the topic of the dissertation. 5 papers, focusing on the subject of the discussed dissertation, have been published: three papers are included in the Clarivate Analytics Web of Sci-ence database with a citation index, one paper is included in Clarivate Ana-lytics Web of Science database Conference Proceedings, and one paper has been published in unreferred international conference preceedings. The au-thor has also made 9 presentations at 9 scientific conferences at a national and international level.Dissertatio